Search Documents

By G. de B. van Niekerk

This paper briefly outlines some mining technology that is used with success in Australia but is not yet fully utilized in South Africa. The following aspects are discussed: improved rotary-drill bit performance, use of trucks and load haul- dump units underground, long-hole raising, blasting techniques, and the use of butterfly roofbolt plates for support.

Jan 1, 1989

By S. Parada, P. T. Jones, M. Guo, S. Smets

The corrosion behaviour of a high-quality rebonded magnesia-chromite refractory in contact with a vacuum oxygen decarburization (VOD) slag with high Al2O3content (15?20 mass per cent) is investigated under VOD process conditions by rotating finger tests in a vacuum induction furnace. The refractory degradation mechanisms are studied by the characterization of corroded microstructures using scanning electron microscopy, equipped with energy dispersive spectroscopy. The influence on the refractory wear of the process temperature and the Al2O3content in the slag is discussed. Keywords: corrosion, magnesia-chromite refractory, VOD slags, vacuum induction furnace

Jan 1, 2004

By R. Abela

In over ninety per cent of mineral sand plants, the most commonly used equipment is the spiral concentrator. The tonnage treated over typical spiral plants can range from as low as 200 ton per hour up to 6 000 tons per hour. Due to the limited capacity of each spiral, plants consist of multiple spirals assembled into banks. The mixture of minerals present in the sand feed requires several spiral stages to achieve the desired mineral recovery. Due to the complexity of the spiral circuits, there are always some design and operating problems that present themselves in plants. These range from slurry distribution, spirals operating at incorrect design parameters and feed variations. The material being treated is difficult to maintain in suspension due to its high density, resulting in segregation and preferential flow in pipelines, distributors and sumps. The objective of this paper is to highlight common problems associated with spiral installations to designers and operators of plants. Practical solutions are recommended in order to prevent and minimize these mistakes in the design. These solutions may be used to improve performance on operating plants.

Jan 1, 2003

By M. Dworzanowski

The beneficiation of fine iron ore will increase in importance in the future because most new iron ore resources will be in the form of lower grade ore deposits that will require liberation of iron ore minerals at finer sizes. Generally this fine iron ore will be beneficiated to produce a pelletizing concentrate with very strict chemical and physical specifications. In addition, because of the increasing demand for iron ore there are now more opportunities to produce by-product iron ore from mining operations producing other commodities. In the past the associated iron ore minerals would report to final tailings but now there is potential value to be realised from by-product revenue. These by-product iron ore opportunities are almost all centred on producing pelletizing concentrate. Currently pelletizing concentrates are produced mainly by various combinations of flotation and magnetic separation. The selection of the beneficiation route will depend on ore mineralogy and considerations around plant capacity and final concentrate quality. The main economic iron minerals are magnetic, haematite being paramagnetic and magnetite being ferromagnetic. This, therefore, means that magnetic separation can be applied, in principle, to all fine iron-ore beneficiation plants. While flotation has a considerable capacity advantage over magnetic separation, the real advantage of magnetic separation over flotation in fine iron-ore beneficiation is that treatment of -10 µm iron ore is possible-in flotation, the feed is deslimed at 10 µm and the -10 µm stream is considered to be final tailings, even though there is often a significant amount of contained iron ore. This paper describes a study around the recovery of fine magnetite in the form of a pelletizing concentrate. The study is based on an evaluation of an iron ore by-product opportunity from an iron oxide copper-gold (IOCG) deposit. Experiments were conducted to quantify the differences in magnetic separation performance with decrease in particle size treated. A mineralogical evaluation of all the test work products was undertaken to facilitate the interpretation of the test work results. These results were then used to propose an economically viable flowsheet for maximizing fine magnetite recovery using magnetic separation.

Jan 1, 2012

By P. M. Mashaba, S. O. Bada

An advanced high internal phase water-in-oil (HIP W/O) emulsion binder and flotation with an internal dispersed water phase of 95 vol% was used to beneficiate South African weathered coal from discard dumps. Five coal samples with calorific values ranged from 8.48 MJ/kg to 20.94 MJ/kg were utilized. The performance of the HIP W/O emulsion was compared to that of kerosene in terms of the physicochemical properties of the clean coal products. A 5 kg/t emulsion binder addition produced a high-quality coal concentrate with 11.76% ash and a heating value of 28.61 MJ/kg from a sample containing 29.34% ash. Using the same dose and coal sample, kerosene resulted in a clean coal concentrate with 17.47% ash and a calorific value of 26.42 MJ/kg. Further samples were also beneficiated using 5 kg/t of W/O emulsion. The highest increase in calorific value was achieved from the beneficiation of a sample containing 48.71% ash, from 8.48 MJ/kg to 18.16 MJ/kg. It has been established that emulsion binders can upgrade coal samples dumped many decades ago.

Aug 2, 2022

By V. B. Teffo

The aim of the project was to experimentally determine the coefficient of restitution, and static and rolling friction of Eskom-grade coal for discrete element modelling (DEM). These parameters will be used in further DEM studies to simulate the flow and behaviour of coal during conveyance. For the simulation to yield realistic results, the parameters for the different coal shapes identified in the samples were determined. DEM uses spherical particles, and it was found that the difference between the DEM default parameters and those measured is significantly different, by as much as 97%, which illustrates the importance of experimentally determining these parameters. The spherical particles in DEM can be used to construct the various coal shapes identified, and the parameters measured can be used to simulate realistic results. The conveyance system can then be optimized accordingly.

Jan 1, 2013

By K. Liddell

Current practice for the recovery of platinum group metals (PGM) from flotation concentrates is by energy-intensive smelting processes followed by separation and refining of the base and precious metals. Energy costs are rapidly increasing in South Africa and this trend is forecast to continue in future years. Moreover, the smelting operations are highly susceptible to deleterious constituents, particularly chromite; and the increasing tonnages of UG2 chromititic ore being mined results in an increasing chromite content of smelter feeds. Hence there is a substantial incentive to assess and implement alternative processes to smelting for the treatment of PGM concentrates. The Kell process is a patented hydrometallurgical alternative to smelting that is totally insensitive to the chromite content of the feed concentrate and comprises three commercially proven unit operations (pressure oxidation leaching of base metals and sulfur, roasting and chlorination of precious metals). The Kell process provides the opportunity for existing and new PGM producers to significantly reduce their energy consumption, and in particular their consumption of electricity, by removing the need to smelt PGM concentrates. Energy costs, greenhouse gas emissions and installed power requirements are also much reduced. Compared with smelting and refining these reductions are calculated as: ? Total energy consumption-50% reduction ? Electrical energy consumption-84% reduction ? Energy consumption costs-76% reduction ? C02 emissions-70% reduction ? Installed power requirement 92% reduction. The data obtained from simple laboratory batch amenability testing can be readily applied to the Simulus mass and energy balance simulation procedure to determine energy and reagent consumptions, equipment selection and process optimization. The applicability of Kell to treating low-grade 'dirty' concentrates with high UG2 content as well as to polymetallic concentrates containing base metals as the major payable metals with subordinate PGM means that these savings can also be expected when the process is used for treating a range of concentrate types and grades. Keywords PGM,UG2, Merensky, smelting, chromite, electricity, hydrometallurgy, Kell Process, Eskom.

Jan 1, 2011

By J. A. Theron

"This paper provides guidelines on performing mass and energy balance modelling involving coal and coal derivatives. Usually, the inputs to a pyrometallurgical process would be specified in terms of elements and compounds. Reliable thermochemical data is more widely available for species involving uniquely defined, relatively smaller molecules. However, in the case of coal, the molecules are extremely large and not uniquely defined. Consequently, modelling processes involving coal and its derivatives involve several potential pitfalls. These are outlined in the present paper.It was found that coal proximate analysis should not be regarded as absolute; it could vary with several parameters, including heating rate. For modelling, the use of ultimate analyses should be considered a preferable option to proximate analyses, where ‘fixed carbon’ and ‘volatiles’ are not defined in terms of chemical composition. Significant errors could be incurred if the larger molecules are neglected during calculation of the calorific value (CV) of coal gas (the gas liberated when coal is heated in the absence of oxygen).For elemental analysis determination, the oxygen content (which is calculated by balance) should be checked to ensure it is within the expected range. For representation of sulphur in coal, one should avoid doublecounting due to SO3 in the ash analysis.Potentially, oxygen in coal could be represented as O2, H2O, CO, or CO2.However, use of some of these species without considering the experimentally determined gross CV leads to significant errors in the energy balance. If coal enthalpy is calculated from elemental analyses without correction, representation of coal oxygen as H2O(l) gives reasonable accuracy. Coal volatiles could be represented by a complex mixture of compounds, even using different oxygen-containing species than these four, provided the enthalpy is corrected.It is recommended that an ‘enthalpy correction value’ be incorporated in energy balances involving combustion, devolatilization, or conversion of coal and coal derivatives, e.g. coke, char, or tar. That would imply that proximate analysis, elemental analysis, as well as the gross CV would be required for all solid or liquid coal-derived substances being modelled. No other correction due to carbon being present in a form other than graphite should be used, as that would imply double-counting some effects."

Jan 1, 2015

By J. J. Dekker

Controlling noise has proven difficult in mining, and noise-induced hearing loss (NIHL) remains common. In 2008, a South African Mine Health and Safety Council study focused on small- to medium-sized mines in relation to the milestones set by the industry to prevent NIHL. An evaluation of the compliance of ten diamond, sand, aggregate and Ready mix concrete mines and production sites with standards, legislation and best practice guidelines relating to NIHL prevention was conducted, using a noise compliance audit tool. The findings indicated that all mines surveyed had poor compliance with the international standards, compliance with International Standards Organization standards being the poorest. There was a clear distinction between the small and the medium-sized mines in their compliance with local standards and legislation (ranging from 14 per cent to 66 per cent). The areas of best compliance were audiology and medical examinations. The lower-than-expected compliance was largely attributable to shortcomings in hearing conservation programmes for occupational noise. Initiation of remedial practices in the small- to medium-scale mining sector to facilitate improvements in NIHL prevention and compliance with standards and legislation is recommended. Keywords Hearing conservation, small-to-medium mines.

Jan 1, 2011

By Grant Loveday, Vincent Dieudonné, Andrew Jonkers

Bateman Minerals & Metals supplies the APIC Technologies which include the under-bed air-pulsed APIC jig and related technologies such as the JigScan controller and advanced mathematical models of the jig process. Bateman have developed a methodology for predicting process performance for jigs from simplified testing and modelling, based on batch equipment matched to industrial designs. Batch tests conducted on laboratory scale air-pulsed jigs can process small batches of material, such as those obtained from drill core samples. The novelty comes from using an advanced jig process model, ASTRAD, to link the results of batch and continuous jigs. The batch jig presented as a novelty in this paper has been designed to be hydraulically equivalent to the full-scale APIC Jig, allowing the generation of equivalent pulse shapes and using JigScan controller. Lump and fine ferrous ore material have been separated in this unit and any feed >1mm can be tested and extracted. The global test procedure and further modelling focus on the stratification of material, with emphasis on key aspects such as pulse shape, feed characteristics and residence time. The splitting of rejects from concentrates is itself more difficult to reproduce in batch jigging, however the ASTRAD model includes a separation imperfection module, and the APIC Technologies have extraction systems adapted to each type of material. Air pulsed batch jigs are available in several locations and are relocatable. They have been used to treat samples from Australia, South Africa and India as part of studies into ore processing using jigs. Each test layer is available for various physical testing procedures (density and chemical analyses). Test-work is performed on a case by case basis, and analysed using an advanced model ?now available over the internet. Some fundamentals of air-pulsed jigging are recapped along with some of the features of APIC jigs. The process of designing a ?hydraulically equivalent? batch jig test is then described. Some results from jigging tests are presented plus the results of the ASTRAD advanced jig model, which was first developed at the JKMRC with ferrous ores and coal and is now being supported and further developed and utilised by Bateman.

Jan 1, 2006

COALTECH 2020 initiated a research project to provide the coal mining industry with a modelling tool to determine the expected types of subsidence, risks and the investment required in post-closure funds to cater for subsidence associated with bord and pillar mines. A detailed literature review was conducted to determine the most important parameters in calculating the cost associated with surface subsidence. A subsidence prediction model was developed to determine the likelihood of different types of subsidence. The study made use of current knowledge of failure mechanisms and its aim is to assist the industry and government in arriving at the most suitable arrangements when authorities require financial instruments to assure compliance with environmental regulations.

Jan 1, 2003

Often plant performance suffers as a result of poor control. Poor control leads to low mill throughputs, poor classification and less than satisfactory concentrate grades and overall recoveries. By using the appropriate control tools, substantial gains in plant performance can be made. Mintek?s MillStar and FloatStar controllers have been implemented at various sites across the world. The MillStar controller incorporates leading technology that controls process units from the mill feed through to the flotation feed. Typical results show that milling circuit throughput is increased by 6-10 % and the final product grind size is tightly controlled, thereby enhancing flotation performance. The FloatStar controller is aimed at stabilising and optimising flotation circuits. Through improved level control alone, recovery improvements of up to 1 % have been achieved. Furthermore, by using on-line grade analysers, the controller stabilises final concentrate grades, whilst maximising flotation recovery.

Jan 1, 2005

By Chris D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900?s. This versatile product displaced the expensive and easily-poisoned platinum-based catalyst in nearly all applications by the 1930?s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has world-wide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development program dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and pre-heater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By Chris D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900?s. This versatile product displaced the expensive and easily-poisoned platinum-based catalyst in nearly all applications by the 1930?s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has world-wide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development program dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and pre-heater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

"In mechanized mining, poor equipment efficiency (availability, utilization, productivity, and quality) can endanger the success of the operation. This case study will show how an initiative to improve equipment performance developed into a comprehensive turnaround plan for the mine that placed it in the forefront of performance achievement.As part of a company-wide review process, poor overall equipment effectiveness (OEE) was identified as a major reason for the mine not achieving its targets. A project to improve the OEE identified eight improvement areas (elements) that contributed significantly to the poor performances. Measurement metrics were determined for these elements, followed by determination of baseline and target (improved) key performance indicators (KPIs). Cost savings associated with the improved efficiencies were calculated and tracked throughout the project. The mine team determined the specific actions required to achieve the target KPI in each element. These were individually developed and managed like mini-projectswith allocated responsibilities for delivery. The paper will indicate how this OEE improvement initiative triggered an improvement in almost all sections of the mine. Soon after launch, the initiative gathered momentum as the KPIs starting to improve. A visible tracking system exists at the mine and each employee can see the improvements and feel the success. The original eight elements were extended by five more, and the mini-projects grew as participants saw the success of the initiative.This paper concludes that through management and worker involvement, visible measurement and controls, and carefully chosen improvement elements, the mine was turned around. It is now achieving and exceeding its targets, and employee relations and motivation as well as safety have improved considerably. All of these achievements are reflected in the bottom line."

Jan 1, 2016

By M. Olper

The change in regulations and the strong attention to the environment have suggested some changes in the traditional processes for the recycling of lead acid batteries. Engitec Technologies, marketing the Integrated CX® System, is continuously updating and improving its technology to fulfil the technical, economical and ecological requirements coming from the market and from the environmental authorities. In this paper Engitec Technologies will present the latest technical innovations introduced in the Integrated CX® System.

Jan 1, 2008

This paper provides a review of the chemical reactions occurring in the submerged arc processing of chromite ores. The excavations of industrial furnaces have shown that the charge, as it descends through the furnace, passes through a number of distinct reaction zones. Each zone is characterised by differing process conditions and reaction products. The phase equilibria, reaction steps and mechanisms occurring as the charge progresses through the furnace are examined, and the potential influences of these factors on the process outcomes are discussed.

Jan 1, 2004

By L. Rademan

The kinetic leaching behaviour of a low-grade surface gold ore and a high-grade reef ore were evaluated to determine the achievable gold recovery from these ores and particularly mixtures of these ores. The reef ore material has a head grade of 13.40 g/t with a relative standard deviation of 3%, and the unprocessed surface ore material a head grade of 0.43 g/t with a relative standard deviation of 15.6%. It is concluded that the kinetic leaching behaviour of these free milling gold ores during cyanidation, is not influenced by mixing of reef and surface ore material. No statistically significant relationship exists between the achievable recovery by direct cyanidation and the head grade of the material fed. No ideal ratio of surface ore to reef ore could be established. It is recommended that these materials should be processed simultaneously to minimize the costs, security risks, and losses incurred in transportation.

Jan 1, 2012

By G. G. le Roux

The purpose of the investigation was to assess various options for increasing the efficiency of the conveyor belt transporting system used at 4 Belt Shaft at Lonmin?s Marikana operations. The reason for the investigation was to prevent the occurrence of a ?bottleneck? at the main ore passes delivering ore to the conveyor belt system, thus creating more fluent operational conditions. The options assessed for increasing the efficiency of the conveyor belt transporting system were: ?Variation of the conveyor speed ?Concurrent tipping from two ore passes on the belt ?Increase the available drive unit power ?Increasing the feed rate from vibratory feeders ?Change in belt width/belt specifications The report shows that the most preferable option to the current situation at 4 Belt, Lonmin, would be the option of concurrent tipping from two ore passes to the belt.

Jan 1, 2008

By J. -W. Kim, Y. -B. Kang, H. -G. Lee

The effect of SiO2addition on the decomposition of Li2CO3was investigated at temperatures up to 1000ºC. It was found that addition of SiO2greatly enhanced the decomposition of Li2CO3. The main decomposition reaction started at around 600ºC, and completed just above the melting point of Li2CO3. The major decomposition product was Li2O?SiO2irrespective of the Li2CO3to SiO2mixing ratio while both reactants were available. It was ascertained that a liquid layer betweenLi2CO3and SiO2particles formed and facilitated the decomposition reaction. The governing reaction of the decomposition was the one between the dissolved Li2CO3and SiO2in the liquid layer to form Li2O?SiO2. The decomposition rate was independent of the Li2CO3/SiO2mixingratio until either one had been completely exhausted. When excess Li2CO3existed, it further reacted with the initial product of Li2O?SiO2to form 2Li2O?SiO2. When SiO2was found in excess, on the other hand, no further reaction took place. This is attributed to the fact that uponLi2CO3exhaustion there is no liquid phase available to facilitate further reaction. The apparent activation energy of the decomposition of Li2CO3in existence with SiO2is 198 kJ mol-1.

Jan 1, 2004