Search Documents

The mineralogical composition of the ore was determined and the mineral phases with which nickel is associated were identified. The ore was prepared by grinding to -420 micrometres and classification into granulometric fractions. Prior to the main series of experiments the effect of agitation rate on nickel recovery was investigated. The influence of sulphuric acid concentration, temperature and particle size on the kinetics of nickel extraction was then studied, both quantitatively and qualitatively, over fixed value intervals. Application of the initial rate method enabled determination both of the order of reaction with respect to sulphuric acid concentration and the activation energy for the dissolution of nickel. The results indicate that a physical mechanism can be ruled out as the rate-determining step in the extraction of nickel from the ore and that a chemical mechanism is more likely

Dec 1, 1991

By G. R. Doughty

It is shown that sodium can be removed very readily from molten aluminium by the use of a beta"-alumina, the more highly conducting form of beta-alumina, provided that the surface of the tube is wetted by a layer of salt. From current/time plots the theoretical amount of sodium removed has been calculated and excellent agreement obtained. The beta"-alumina tubes can be immersed directly in the Al without fracturing if they are pre-heated for a few minutes prior to immersion. According to its stability beta"-alumina should be attacked by molten Al at low Na contents, but in these experiments the salt acted as a protective layer. Magnesium chloride is a relatively cheap salt, whose Mg product can be used within a foundry. The only other product is NaCl, which can be used in-house as a flux or sent for disposal. No polluting gases are used or produced and no drosses created. The time for removal of sodium was quite short, comparable to that for chlorination

Jun 21, 1905

By Ruddle R. W.

Solid mattes are generally held to be either (a) eutectiferous mixtures of the component sulphides Cu2S and FeS or (b) mixtures of complex sulphides. This chapter shows that liquid mattes consist essentially of a homogeneous phase in which iron, copper and sulphur are present. The amount of sulphur is generally less than that required to account for all the metals as stoichiometric sulphides; mattes cannot therefore be regarded as mixtures of FeS and Cu2S. Some iron oxide may be dissolved in the sulphide phase and magnetite is often present as a second phase. If the sulphur content of the matte is reduced the composition enters the miscibility gap in the ternary system and either an iron- or copper-rich solution (depending upon the composition of the matte) separates as a new phase. On solidification any one of four phases (iron, copper, Cu2S and FeS solid solutions) may crystallize as primaries. The remainder of the matte solidifies as a ternary eutectic. It is possible that iron oxides enter into this eutectic. Knowledge of the ternary Cu-Fe-S system is far from complete and nothing is known of the quaternary system Cu-Fe-S-O

Jan 1, 1953

By G. Mellgren, O. Mellgren

The conductivity of a solution is often used industrially to control the salt concentrations of reacting systems, normally using electrodes made of glass fitted with platinised platinum electrodes. When a standard platinum conductivity electrode was used to control the acid fed to the leaching circuit for an ilmenite flotation concentrate at Titania, Norway, a deposit of calcium sulphate (containing some calcium phosphate) covered both the platinum electrode and the external glass fitting, rendering the electrode inefficient in the course of a few minutes. A new electrode consisting of a casing, two measuring tubes and an electrode stem is described and illustrated. A significant advantage of its design is that the useful range of conductivity measurement can be adjusted by adjusting the concentration of the electrolyte in the electrode. It has been in use at Titania for about four years with an electrolyte consisting of 0-1 n HCI. It is robust and demands little maintenance.

Dec 1, 1971

By C. C. Harris

The use of Alyavdin's equation Y(x,t) = 1-e(-bt) for describing the effect of grinding time on size distribution is discussed. The equation transforms into linear form by expressing it as log-log reciprocal (1 - Y) versus log t. For plotting, specially divided grids are available; Rosin-Rammler or Weibull charts may be used. The data of Herbst and Fuerstenau are especially useful for illustrating the Alyavdin-Weibull chart in two applications: (1) presenting data (which are relatively unaffected by experimental scatter) and comparing them with theoretical predictions, and (2) as a test for the zero-order kinetics production hypothesis. The chart based on the Alyavdin-Weibull equation is suggested as a useful aid in the analysis of kinetic data (/ versus f), though not as a procedure in its own right. Proposed applications are (1) displaying data with excellent clarity, since it avoids the kind of congestion inherent in some other plotting methods, and (2) as a test for assumed kinetic relationships. Sometimes, equation 1 describes the data quite closely, and in these cases the parameter values appear to be related to certain operating conditions.

Dec 1, 1971

1994 estimates for Porgera are probable and proven reserves of 58 200 000 t of ore grading 5 g/t Au. Gold mineralisation is related to an intrusive complex emplaced at shallow levels in poorly consolidated sedimentary rocks. The complex is located in a zone of fold-and-thrust deformation, whose formation may have been initiated shortly before emplacement and continues locally today. Abundant primary magnetite in the complex gives an intense, 5 km wide aeromagnetic anomaly. The deposit formed during two main stages of mineralisation, the first related to early magmatic-hydrothermal activity and the second representing later epithermal overprinting centred on the Roamane fault. Hydrothermal alteration followed closely on emplacement indicating a close genetic relationship between magmatism and mineralisation. Both stages of hydrothermal activity post-date and overprint early propylitic alteration. Several factors have acted in unison or sequentially to concentrate metals at the deposit, including an extensional or trans-tensional tectonic setting within an arc or collisional environment, the exsolution of a magmatic hydrothermal fluid prior to sulphur saturation in the melt, the development of the hydrothermal system into one favourable for transporting gold, the action of late-stage faulting in focusing epithermal fluid flow, and the role of dissolved gases in promoting fluid phase separation and high-grade ore deposition

Jun 19, 1905

By R. Winand, P. Harlet

he cathodes produced are of electrorefined grade; metallographic structure and surface roughness are controlled to a depth of 1.3 cm (single-side deposits); silver levels in the cathode are regulated by the presence in solution of Cl- and Br- ions; organics must be used at very low concentrations (around 0.1 mg/l with a consumption of about 0.01 mg/l/hr). The required concentrations of additives were established according to a well-defined strategy based on the consumption of organics at the cathode by a mass transfer limited-process.

Jan 4, 1992

By S. Vardy

The paper notes that the extraction of 22% of the remaining workable reserves in the north western area involves a risk of spontaneous combustion higher than is normal in Britain. Mining systems have been tailor made in order to minimize the risk of spontaneous heatings, and these systems are described. Well-proved methods of combating spontaneous combustion are referred to, as well as the limitations which now apply to them as the result of the introduction of modern mining techniques. A substantial part of the paper is devoted to the circumstances in which spontaneous combustion occurs underground in the north western area. Several actual incidents which have occurred in the last few years, along with the practical application of the lessons learned, are described. Of particular note are: a) the procedure adopted in the north western area to equalize pressure differences across stoppings using pressure chambers, and b) a retreat mining system, primarily designed to deal with high methane emission and steep gradients, which also affords some protection against spontaneous combustion.

May 23, 1905

By K. C. Misra, W. Wrightson Jr.

The Lick Fork prospect shows appreciable nickel sulphide mineralization in a narrow, steeply dipping, layered sequence of metamorphosed hornblende peridotite, gahhro and hornblende gahhro, intrusive into the Pedlar Formation (charnockitic pyroxene granulite) of the Virginia Blue Ridge Complex (Precambrian). Rocks of the intrusion have equilibrated to granulite- facies metamorphism, as indicated by pervasive polygonal texture of silicate aggregates, development of biotite- and hornblende-preferred orientation, compositional equilibration of the silicate minerals, the Mg-Fe2+ (orthopyroxene-dino- pvroxene) distribution coefficients (average 0.57), (MgO + FeO + Fe20 3)/Al20 3ratios in orthopyroxenes, and Ti contents and AI(i\)/A I(\i) ratios of hornblendes. The sulphides, consisting of pyrrhotite-pentlandite (with up to 4 wt% Co)-chalcopyrite-pyrite-marcasite-violarite- bornite—mackinawite, are virtually restricted to the ultramafic unit of the intrusion and constitute 20-30% of the samples of hornblende peridotite studied. Although the basal accumulation of the sulphides may suggest magmatic segregation, sulphide- silicate textures typical of sulphide liquid immiscibilitv are not present, even in the sparsely mineralized gahbro units. On the other hand, the transgressive and relict textures are strongly suggestive of replacement of the silicate minerals by sulphides. These include chaleopyrite ± pyrrhotite ± pentlandite (violarite) ± pyrite ±magnetite veins crosscutting silicates, sulphide penetration into silicates at silicate-sulphide contact zones, rounding of silicate grains against sulphide matrix, and islands of silicate minerals (olivine, hornblende, pyroxene, biotite) in sulphide masses. Metamorphic mobilization of pre-existing sul­ phides is a possibility, but involvement of post-metamorphic, hydrothermal fluids is suggested by the following features: paucity of annealing and deformation textures in the sulphides, replacement of metamorphic and deformed silicates, lack of differential sulphide mobilization and the common occurrence of sulphides along grain boundaries and triple junctions of poly gonal silicate aggregates. The consistent association between sulphides and hydrothermal alteration products of silicates suggests that they are cogenetic. The hydrothermal fluids may have merely mobilized and concentrated the pre-existing, disseminated, magmatic sulphides, or there may have been significant addition of sulphides during this process. This question cannot be resolved unequivocally with the existing data.

Jan 1, 1984

By Evans E. C.

At first sight, the extinction of a mine fire by the action of some such gas as carbon dioxide would appear to be quite a simple and practicable operation. From a consideration of the theoretical aspects only of the question, it becomes evident that the matter is not so simple as it appears to be at first sight. The fire at the Senghenydd Colliery occurred as the result of the disastrous explosion of October 14th, 1913. This explosion was confined to the west side of the colliery; and as a result the timbers in the main intake on this side were set on fire; but these were soon buried beneath falls, and the tire continued under them. Attempts were made to extinguish it with water, with the aid of chemical extinguishers, and by digging it out; hut these had to he abandoned, and ultimately the fire-zone was sealed off by “ bashings” (stoppings). By December, progress in the decrease of combustion was so slow that it was decided to try the effect of inert gas. The installation, control and operation of the carbon dioxide plant and associated water-gauge are described in detail and conclusions drawn for the extinguishing of mine fires by CO2

Dec 1, 1916

By D. J. Allan, W. R. Wilson

For conventional aerospace aluminium alloys of the 2000 (copper) and 7000 (zinc, magnesium) series the recycling of process scrap from both metal suppliers and aircraft manufacturers is a well-established, worldwide industry. The recent introduction of a new family of alloys that incorporates lithium has posed a new challenge to the recycling industry owing to the high cost of lithium, its high reactivity to the atmosphere and to refractories and its absence from the specifications of all other registered alloys. Various process options for recycling have been identified, but vacuum distillation has been selected as the most cost-effective and technically feasible solution. Experimental work established that the separation of Li from AI-Li scrap is feasible and an industrial process has been designed. The economics of Li recovery are very sensitive to the AI-Li content of the feed material. Owing to the design of aerospace vehicle manufacturing plants it is expected that the swarf will be mixed with other alloys. A method of enriching this feed has been developed that is based on the control of swarf morphology by thermal and mechanical treatments as a precursor to eddy-current separation. After eddy-current separation and vacuum distillation small proportions of Li are retained in the AI residue. The effects of this on the properties of conventional AI-Si shape-casting alloys were investigated and safe threshold levels have been established.

Jan 4, 1993

By P. Danson, D. A. White, S. Bashir

Composite ion exchange materials made of SnO2, TiO2 and MnO2 can be used to remove radioactive contaminants from nuclear waste streams. In several cases their selectivity and capacity are enhanced by mixing hydrous silica into the matrix. MnO2-SiO2 materials are especially useful for a number of reasons, such as their selection of heavy elements over caesium. Distribution constants and determinations of exchange capacities show that in many instances the properties of the composites are better than those of the oxides alone, while the presence of a chelating agent has been found to reduce the uptake of nuclides considerably. Methods are being developed for the bulk manufacture of the materials. Further work on sorption mechanisms is required to explain anomalous results, particularly the variation in exchange capacity for different elements and the ability of the oxides to sorb colloidal material in alkaline solution.

Jan 8, 1992

By D. J. Wall, T. D. Johnson, M. T. Parry, G. R. Heath

In coal-fired power stations coal is ground to a fine powder and then transported pneumatically at 25-30 m/s velocity to remote burners. Wear of the conveying pipework is a well recognised problem and traditional lining materials are Nihard and basalt. In many cases these are being replaced by alumina tiles in order to improve life and reduce the frequency of replacement. A programme of laboratory testing of candidate aluminas with AIO, contents between 85% and 99-5% has been undertaken and the results compared with field experience. This gives confidence in the erosion tests, which were designed to replicate most of the field conditions. However, it has not proved possible to draw correlations between the laboratory erosion rates and any of the materials’ bulk properties. SEM, TEM and microanalysis studies have therefore been made in order to look for microstructural aspects that could be influencing erosion rates and it has been shown that intercrystalline cohesion, the matrix phase and porosity appear to have most influence on wear performance. It is necessary to quantify these microstructural parameters if reliable erosion performance is to be obtained. This paper was read at the Institute of Ceramics Annual Convention at the University of Durham, April 1988.

Jun 12, 1905

By D. R. Hudson, M. J. Donaldson

"Study of gravity concentrates from the gold-recovery circuit of the Kambalda nickel mill has enabled an assessment to be made of the nature, relative abundance and compositional variability of platinum group element (PGE) minerals and other associated heavy minerals that are present in the Kambalda nickel deposits. The major platinum minerals are sperrylite, PtAs2, and nioncheite, (Pt. Pd, Ni)(Te, Bi)2, and the major palladium minerals are sudburvite, (Pd, Pt, Ni)(Sb, Te, Bi), stibiopalladinite, Pd6Sb2, and palladoarsenide, Pd2 (As, Sb), together with a palladium antimonide and a palladium arsenide that have not been fully characterized. Palladian melonites, which contain up to 10 wt% Pd, and palladian nickeline are also important PGE hosts. Sperrylite and sudburyite are by far the most abundant discrete minerals in the gravity concentrates.Gold occurs as argentian, cuprian and nickeloan—cuprian gold, and as the tellurides calaverite, petzite and auriferous hessite. Silver is present in petzite, hessite and volynskite. Other rare phases contained in the gravity concentrates include native bismuth, altaite, frohbergite, breithauptite, gersdorffite, parkerite, scheelite, tantalite, cassiterite, rutile, bunsenite, gahnite, barite and uvarovite.Descriptions of in-situ occurrences of PGE minerals at Kambalda are rare. Michenerite, PdBiTe, and testibiopalladite, PdSbTe, have been described from a telluride-rich quartz-carbonate vein that intersects massive sulphide ore in Lunnon Shoot. Moncheite has been observed in chalcopyrite-rich stringers, and sudburyite occurs as inclusions in nickeline in a quartz- carbonate veinlet. No discrete PGE minerals have been found within the massive and matrix ore zones in the Kambalda ore- shoots, and the geochemical distribution of PGE suggests that the formation of discrete PGE phases may be related to post- magmatic processes—in particular, metamorphic segregation of sulphides, and the interaction of the ore sulphides, containing PGE in solid solution, with younger hydrothermal fluids. This has led to local redistribution of the PGE, with concentration in footwall stringers and veins, and in reaction zones."

Jan 1, 1984

By Haldane J. S.

(Paper presented at the Institution of Mining Engineers' general meeting held in London on 8th June 1916.) It was shown in the last Supplement to the Registrar-General's Reports, in connection with the census of 1901, that the general death-rate among colliers was considerably lower than in the great majority of occupations but that there is an exception to this in the case of colliers above the age of 55. Examination of the statistics finds that the excessive death-rate among old colliers is to a large extent only apparent, and that the real excess of bronchitis from which they have suffered has greatly diminished. It is concluded: (1) that good ventilation is of considerable importance to the health and continued working efficiency of miners, as well as to their safety from accidents; and (2) that there is no real statistical evidence of harm resulting from the inhalation of coal-dust or shale-dust in the quantities ordinarily breathed by miners, and a strong presumption that the dust they breathe protects them against serious dangers from bacilli that are removed from the lungs by the dust-clearing cell mechanisms

Dec 1, 1916

By Y. L. Ding, N. A. Warner

Cylindrical pellets made from graphite and chromite mixtures were reduced in high-carbon ferrochromium melts at 1 600-1 695 degrees C, under an atmosphere of almost pure CO. The reduction rate, as measured by gas evolution, increased with increasing melt temperature and graphite addition and with decreasing pellet diameter or height, although reductant particle size had a very limited effect on kinetics. At a pellet size, heat and mass transfer were significant in controlling the early stages of reduction of large pellets while at chromite grain size, gas diffusion was probably a rate-controlling step. The time required for dissolution of unfluxed pellets into the melts was significantly longer than that for reduction. This indicates that pellet dissolution may be the limiting factor in determining the operating parameters for a proposed new process to produce high-carbon ferrochromium using melt circulation

Jun 19, 1905

By Gibson J.

The writer hopes to prove that the economical tram is of even greater importance than, say, the economical engine, and as no difficult and involved calculations are required, and all the governing facts are simple and well known, the former is more easily attainable than the latter. In the first section of this paper the factors that determine the size and the construction of the tram are examined; whilst in the second section the road on which it runs is dealt with

Dec 1, 1916

Paper presented at the Mining Institute of Scotland's annual general meeting held in Glasgow, 8th April 1916. Although there is nothing novel or difficult about the sinking described, circular shafts are not numerous in Scotland so the details connected with such a sinking may be of interest. The shaft was sunk at Dykehead Colliery, Larkhall, which has been worked for over 50 years from the upper seams. It became necessary to sink another shaft to serve as a replacement downcast, by which the output might be maintained and some of the lower seams won. As the sandy clays regularly caused bulging into the rectangular shaft and sinking of the surrounding ground it was decided to make the new shaft circular and to enclose its mouth in a foundation-block of concrete resting on the solid clay. Details are given of the sinking, brick seating and lining, kettle strike, water-rings and doorhead lintels as well as the permanent fittings, winding gear and the cages themselves

Dec 1, 1916

By P. C. Kapur

Several empirical and semi-empirical laws of comminution, which describe the relationships between the cumulative grinding energy input and the degree of size reduction of brittle solids, have been rationally derived in the time-domain in a unified manner, starting with an integro-differential equation of grinding kinetics. The analysis leads to and provides explicit interrelationships between the energy-size reduction laws associated with Kick, Rittinger, Holmes, Bond, Charles and others, and gives useful estimates of their relative merits and validity. It is shown that Holmes' expression is, in fact, a solution to the grinding equation; consequently, this classical law is compatible with the modern theory of comminution based on population balance on particulate species

Dec 1, 1971

By D. Newman

Mineral production in the Highlands and Islands of Scotland during the last ten years has been confined to the sporadic production of industrial minerals—for example marble, anorthosite, limestone, talc and silica. From 1962 onwards there has been an upsurge in mineral exploration in the Highlands, increasing in tempo from 1966 onwards due to the efforts of the Institute of Geological Sciences, the Highlands and Islands Development Board, and private and public companies. Geological, chemical and economic aspects of some of the more interesting mineral prospects are discussed: these include anorthosite, feldspar, magnetite, quartzite and brucite marble. Reference is made to a geochemical survey undertaken in the Rosehall district of Sutherland, the results obtained being summarised. Problems that affect the future of mineral exploration in the Highlands are stated.

Dec 1, 1971