Search Documents

By R. J. Howarth, P. L. Llowenstein

The errors resulting from field sampling, sample preparation and analysis are investigated for drainage sediments derived from homogeneous sandstone, shale, limestone, basic igneous and granite lithologies as a background to a primary reconnaissance survey of England and Wales. Emission spectrographic analyses of approximately 350 samples for Al, Ca, Fe, K, Si, Ba, Co, Cr, Cu, Ga, Li, Mn, Ni, Pb, Sc, Sn, Sr and V and atomic absorption analyses for Cu, Ni, Mn, Co, Zn and Pb have been treated statistically. For routine broad-scale surveys analysis of the unground -80-mesh sediment fraction proves satisfactory. Sampling error between localities in a stream is shown to be less than spectrographic analytical error for many of the elements considered here, except where mineralisation (contamination) occurs, but exceeds the atomic absorption analytical errors in most cases. Unless it it critical to reduce the amount of between-site variability (having regard to analytical errors) in the regional survey, there appears to be no advantage in the use of a more sophisticated sampling technique. The utility of moving-average maps in reducing the width of the confidence belt around the regional 'geochemical surface', and thus compensating to some extent for the sampling errors, is also demonstrated.

Dec 1, 1971

By I. A. Scott, T. J. Napier-Munn

Size-by-size partition curves for mineral separation in dense-medium cyclones pivot about a single characteristic point. This is defined for stable, non-segregating media by the medium density and the proportion of the medium reporting to the underflow. The pivot point departs from these values for unstable, conventional media. The phenomenon can be represented by an equation with two parameters defining pivot point coordinates and two the Ep value. On the basis of experiments in a 200 mm cyclone using ferrosilicon media, simple regression equations were developed for the separation parameters in terms of operating conditions (the coefficients were likely to be site-specific). The experiments successfully decoupled the effects of medium density and viscosity and showed that the value of Ep was independent of the former but strongly dependent on the latter. A classification model was used to predict the density of the underflow medium, a knowledge of which is required to determine the pivot parameters. The model correctly reflects the performance trends observed in dense-medium cyclone operation and has the potential to be generalised to a wide range of industrial practice.

Jan 8, 1992

By A. Ludkin

The paper presents the history of the occurrence of spontaneous combustion in the north area, together with the associated problems. These are examined and a description is given of the methods used to combat the danger, including the use of modern scientific instrumentation. Detailed reference is made to the underground trials with pack injection and sealant coatings which were carried out at Seafield Colliery following the formation of a working group to assess the performance, in the same underground conditions, of (1) sandbagging, (2) pack injection, (3) surface coating. Based on these trials, an improved and more economical method of prevention has been established. There is, however, still scope for further improvement in techniques which would take into account the problems of gradient, transport, manpower and cost.

May 23, 1905

By C. M. Lesher, R. R. Keays

"The komatnte-associated Fe-Ni-Cu sulphide mineralization at Kanihalda, Western Australia, is generally believed to be magmatic in origin, but a number of postmagmatic processes significantly modified the original distribution, structure, texture, mineralogy and chemistry of the ores. Two important types of mobilized magmatic sulphides are interpillow/interbreccia sulphides and hydrothermal vein-type sulphides. Interpillow and interbreccia sulphides occur interstitial to pillowed or volcaniclastic footwall metabasalts beneath or adjacent to the stratiform contact ore horizons. They are mineralogically and compositionally similar to massive ores (and are similarly depleted in PGE relative to the compositions of bulk samples of mined ores), but normally do not contain the distinctive chalco-phile ferrochromites characteristic of contact ores. They are interpreted as magmatic sulphides that have been mobilized from the overlying or adjacent massive sulphide layer during peak tectono-nietamorphism.Hydrothermal sulphide-quartz + albite veins also occur in the footwall metabasalt and contain unannealed deformation fabrics indicative of emplacement during retrograde metamorphism. The high Ni and Pd contents of these sulphides (7-13% Ni, up to 70 ppm Pd) indicate that the metals have been derived from the spatially associated komatiites and/or contact ores, consistent with the Pd depletion previously inferred for massive ores. Very low Ir contents and high Pd/Ir ratios of the vein-type sulphides confirm an aqueous transportation-deposition mechanism; hydrothermal transfer of PGE results in strong decoupling of Pd from Ir.There appears to be a complete continuum of sulphide mobilization at Kambalda ranging from whole-scale phy sical dislocation (fault offset ores) and selective mobilization (stringer sulphides) through nietamorphie replacement (interpillow/interbrec- cia sulphides) to jiydrothermal dissolution and redeposition (vein-type sulphides)."

Jan 1, 1984

By D. W. Holliday

The major deposits of anhydrite and secondary gypsum in Jamaica occur discontinuously at a single horizon within the Lower Eocene succession of southeast Jamaica. They are not intruded from other horizons of different age, as has previously been supposed. The gypsum and anhydrite occur in a regressive sequence at the junction between marine (Richmond Formation, Halberstadt Volcanics, Halberstadt Limestone) and overlying non-marine (Wagwater Formation) sediments. They are thought to have been formed in an arid supratidal (sabkha) environment. A variety of 'nodular' structures occurs in the gypsum and anhydrite which can be related to early diagenetic processes and compaction effects. All gradations exist between single isolated anhydrite nodules and structureless anhydrite due to closer packing and coalescence of nodules. The structures and textures in the anhydrite are thought to be consistent with penecontemporaneous formation from gypsum crystals rarely more than 2 cm in diameter. Single anhydrite nodules are not usually larger than 2 cm; nodules of greater size are compound, due to the coalescence of several smaller nodules. Some large compound nodules may have developed from single sand crystals or rosettes. Compaction of anhydrite appears to have been largely mechanical, but some rocks have an aligned fabric, suggesting later flowage

Dec 1, 1971

By J. Ivon Graham, T. D. Jones

This paper presents methods in use in British coal-mines for the suppression of dust. While the effect of present-day treatment will not be apparent for several years, in pits in South Wales, concentrations as high as 50 gm./1,000 cu. ft. were some years ago fairly common in various operations at or near the coal-face, with an average concentration of 20 gm./1,000 cu. ft. Now the average concentration in what were previously dusty pits is probably not greater than 3 gm./1,000 cu. ft.Nevertheless, every effort must be made to improve conditions still further. In South Wales it is claimed that 99% of the coal-faces requiring treatment have been dealt with either by wet cutting, infusion, or hand-spraying. The extent of the treatment by these methods can be gauged by the fact that the total length of coal-faces now being treated by water infusion in Cardiff and Swansea areas is about 33,000 yds., by wet cutting 25,000 yds., and by hand-spraying nearly 14,000 yds. The influence of methods of mining upon dust production is only mentioned very briefly in this review, and there is no doubt that much more is to be learned concerning this aspect. It can be stated, however, that good mining practice is essential to prevent unnecessary dust production, and the problem of dust in mines will be solved only by the closest co-operation between mine managers, workmen, and scientists.

Jan 1, 1947

Discussion of the papers with a written contribution and authors' written replies.

Jan 1, 1947

By S. Y. Ezz

Report of discussion at February, 1971, IMM general meeting (Chairman : M. J. Cahalan, President) of a paper published in Transactions/ Section C (Mineral Processing & Extractive Metallurgy), vol. 79, September, 1970, pp. C226-C233 with contributions by Wild R. and Astier J. on fluidised bed reduction of iron ore fines

Dec 1, 1971

By I S. Lowndes, K. Moloney

Diesel powered equipment is currently used extensively in mining and tunnelling operations around the world due to its mobility, flexibility and through selective application to enhance productivity. However, the increased use of diesel equipment has exacerbated the pollutant load (including heat, humidity, exhaust gases and particulates) placed upon the environmental systems of many underground operations. This expansion in the use of diesel equipment has prom pted researchers to evaluate m easure ment and control technology. This paper reviews the recent research conducted in various countries.

Jan 10, 1996

By Dean S.

Further discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 12th February 1916, with Mr. T.Y. Greener, President, in the chair, of the paper published in Trans. I.Min.E. vol.L, 1915, p.179 and 388. Written contributions to discussion included Mr. Dean's reply to earlier discussion (p.35-44), further written contributions by Tate S. (p.44-54) and Brown E.O.F. (p.54-56), and oral comments by Hare S., Merivale J.H., Greener T.Y. and Tate S. Particularly debated were the causes of the difference in output between American and British coal miners

Dec 1, 1916

By J. H. Chesters

The main, though rarely mentioned advantage, is likely to be the standardisation of best practice and product. In a batch process conditions vary cyclically, but with a continuous process they would, at least ideally, remain the same for long periods of time. The other main advantages of continuous over batch processes are likely to be reduced operating and capital costs, the improved possibilities for automatic control, and more consistent product quality. Recent developments are surveyed for ironmaking and steelmaking with reference to blast furnaces; solid-product and molten-product direct reduction; the trough-type processes of Thring, Worner, the Japanese National Research Institute for Metals and Glinkov; basic-oxygen furnace (LD) variants; spray steelmaking; continuous casting and vacuum degassing; rolling; and coating. Encouragement in the devleopment of continuous processes may be drawn from the way unexpected difficulties, such as trouble with sulphur and refractories, were tackled and overcome to achieve the float glass process

Dec 1, 1971

By R. B. Scott, J. Hewitson

The paper investigates the historical information relating to spontaneous heatings which have occurred within the area from 1955 to date. From this information the seams most liable are identified and the location within the workings is enumerated, together with the possible reason for the occurrence of the heatings. Details are given of the precautions taken during development, working and withdrawal. Sampling procedures are outlined and the interpretation of the results is discussed. Reference is made to the various types of material and techniques employed in both preventing and combating heatings and examples are given of their relative cost and the operational experience obtained. Special observations are made on the changes in mining techniques and their influence on spontaneous combustion.

May 23, 1905

By J. C. Loretto

The philosophy and detail of mill design in developing countries, where it is frequently difficult to obtain experienced, qualified supervision to operate the plant, are discussed. The resulting design suggests the desirability of simple units, with maximum visibility of equipment operation and material movement, which allow the minimal technical supervision to see the plant conditions prevailing. Information on plant conditions during periods of lesser supervision can be provided by the use of simple, low-maintenance recorders. Where the mill is intended for operation in a developing country, it is insufficient for the flowsheets and plant layouts merely to be drawn: the process metallurgist must pay meticulous attention to details that could ordinarily be left to the design detailing group. The design of this type of mill requires a knowledge of human engineering—of the type of individual who will operate and supervise the plant; probable changes in personnel should be taken into account. Details are suggested for coarse-ore handling, screens, feeders, secondary and tertiary crushers, conveyors, dust collecting, fine-ore feeding, grinding mills, conditioners, flotation, thickeners, filters, reagent systems, sand pumping, sampling, instrumentation, safety and construction

Dec 1, 1971

By J. Laskowski, J. Lekki

"The mechanism of joint action of a frother (alpha-terpineol) and a collector (ethyl xanthate) in the flotation of chalcocite has been examined. In order to study the dynamic effects of frother and collector in bubble-particle collisions, the following aspects were investigated : determination of zeta-potential. Measurements of the thickness of fluid film on the surface of chalcocite and adsorption of xanthate, as influenced by alpha-terpineol, induction time and flotation versus concentration of alpha-terpineol and ethyl xanthate.The mechanism of the adsorption-desorption phenomenon on chalcocite with regard to non-ionic molecules, e.g. a-terpineol, has been considered, and the influence of this on the stage and thickness of the intervening wet layer between a bubble and a particle, changing the probability of collision and attachment, is suggested."

Dec 1, 1971

By K. C. Dunham, M. Solomon, T. A. Rafter

Sulphur isotope ratios have been determined for 81 sulphides and S and O isotope ratios for 26 barites from the Alston Block in the northern Pennine ore field. In addition, both isotope ratios have been determined for 29 evaporitic anhydrites of various ages from European and Australian localities. The consistency of the sulphate isotope ratios over a wide area of the northern Pennines, and their similarity to values for Lower Carboniferous evaporites, suggests that the sulphate originated from Lower Carboniferous connate waters. It is suggested that these mingled with warm brines rising through granitic plutons beneath Tynehead and Upper Weardale, the aqueous sulphide ion in these brines having a delta34S value of approximately +10 per mille. The delta34S values for the sulphides range from +15.0 to -5.9 per mille and show an outward zoning with higher values in the central fluorite zones and mainly negative values in the outer barite zones. The wide range of delta34S values for the sulphide S is not characteristic of magmatic S and there is no adequate local source in the Carboniferous sediments. It is suggested that formation waters, probably mainly of connate origin, sank down sufficiently deep to become heated above 200°C before rising through Caledonian granite plutons into the Carboniferous sediments, where they spread laterally to mingle with cooler sulphatic connate water. The rising fluids were hypersaline brines carrying F, Ba, Pb, Zn, Cu and S. Temperatures of deposition calculated from galena-sphalerite isotope fractionation are similar to temperatures previously determined from fluid inclusion studies.

Dec 1, 1971

By P J. Borrington

Offering 1000 hour salt spray protection, the KEYCOAT 1000 coating presents no chipping, cracking or deformation when hammered or flexed through 90 degrees or more. This cost-effective metal protection system features lubrication performance equal to molybdenum disulphide and Poly Tetra Fluoro Ethylene (PTFE) grease providing complete anti-seize protection whilst aiding assembly and disassembly. In addition, the coating is impervious to acids, alkalis, solvents and attack by oils and all fuels. KEYCOAT 1000 has been exhaustively tested in three main industry sectors - automotive, heavy earthinoving vehicles and chemical - where it lias been proven to outperform conventional systems in all respects and as the film formed is less than one thousandth of an inch thick (typically 20 microns), it rarely presents the engineer with any tolerance difficulties. KEYCOAT 1000 is one of a w ide family of products which offer protection and lubrication to a wide industry base, from aerospace to food and with temperatures ranging from minus 190 C to plus 30 C.

Jan 4, 1997

By T. J. White, R. A. Farnfield

Early computerised blast monitoring equipment consisted of a digital version of the existing analogue machines with, perhaps, a few enhancements. Many additional facilities have since been developed to enable the efficient collection of high quality data. These developments are examined with reference to digital sampling, triggering systems, the storage of complete recordings and signal processing. Recent advances have been made in the use of blast monitoring systems that comprise multiple blast monitoring locations with centralised control and data collection. Software has been developed to help record blast parameters and assess environmental effects. Computer databases have many advantages over their paper counterparts. Data can be easily retrieved and processed. The scaled distances used in the prediction and control of peak particle velocities can be calculated rapidly when the data are obtained directly from a database. Since the whole vibration signal can now be recorded, signal processing can be used to provide information such as signal length, dominant frequency and response spectra.

Jan 4, 1993

The probability of detachment of quartz particles from air bubbles during bubble oscillations was investigated by means of a vibration method. Theoretical calculations of the detachment force based on the work of Nutt and Schulze for a single spherical particle show a correlation with the experimental results described. However, the forces that were determined experimentally were considerably lower than the theoretically derived values. Some of the factors which were expected to affect the probability of detachment, such as particle size, bubble size, collector concentration and vibrational acceleration, were also investigated

Dec 1, 1991

"The sulphide nickel resources of Australia are concentrated in the Western Australian Shield. This shield is considered to have developed by extensive, but incomplete, Proterozoic reworking of once-continuous Archaean crust. It now constitutes relic Archaean cratons and intervening orogenic mobile belts transected by narrow, curvilinear tectono-thermal mobile belts of younger Proterozoic age. Remnants of the Archaean cratons are exposed in the Yilgarn and Pilbara Blocks. In the former an ancient (to ca 3600 m.y.) high-grade gneiss terrain (Western Gneiss Terrain) occurs along the western margin of the block and is interpreted to flank younger (ca3000-2800 m.y.) greenstone belts to the east. Ancient (to ca3500 m.y.) granitoid-greenstone terrains dominate the Pilbara Block.Proterozoic mobile belts contain only traces of nickel mineralization, except for one locality in the Halls Creek Province. The Archaean high-grade gneiss terrains contain no important mineralization, and the Pilbara granitoid-greenstone terrains contain only scattered examples of less important types of mineralization.The important deposits (e.g. Kambalda, Windarra, Agnew, Mt Keith) are all of komatiitic affinity and are best developed in the youngest greenstone belts of the eastern part of the Yilgarn Block. In particular, they are concentrated within, and adjacent to, the Norseman-Wiluna Belt, which contrasts in age, lithofacies and structural style with all other greenstone belts in the shield. It is interpreted to have been a rift zone. Within this belt the two main deposit types—the volcanic peridotite-associated and intrusive dunite-associated deposits—are concentrated into spatially separate zones. Precise controls on this heterogeneous distribution cannot be determined unequivocally from available data. One possibility is that the major volcanic peridotite-associated deposits were developed selectively in the actively subsiding axial part of the rift zone during the early extensional phase, whereas intrusive dunite-associated deposits were formed during a subsequent (less active?) stage of volcanic basin development. Distinctive sub-types (facies) of the volcanic peridotite-associated deposits form clusters that are generally within the rift zone. These may represent deposits related to discrete eruption centres, and at least part of their variation is due to relative position within extensive, topographically confined, linear flows."

Jan 1, 1984

By Ruddle R. W.

Magnetite occurs in the reverberatory furnaces, blast furnace and converter (a) as the result of its presence in the materials charged, and (b) as the result of oxidation of the FeS in the charge in the absence of sufficient SiO2 to slag the FeO as it is produced and thus prevent its subsequent further oxidation. Magnetite is reduced by FeS according to FeS+3Fe3O4=10FeO+SO2 and similar reactions. This reaction is markedly affected by temperature and does not proceed to any important extent below about 1200°C. To ensure comparative freedom from magnetite it is therefore necessary to raise the temperature of the furnace to the highest practicable figure and to use plenty of siliceous flux. Since the maximum operating temperature is likely to be limited by the resistance of the refractories to attack by the slag, investigation of the factors affecting this attack should be helpful. It is reasonable to suppose that the formation of magnetite might be minimized by ensuring intimate admixture of matte and slag during conversion so that silica is readily available for combination with ferrous oxide as the latter is formed. The literature gives no clue to the importance of this factor and some experimental work on this aspect might be fruitful

Jan 1, 1953