Search Documents

By Yuexin Han, Jie Liu, Shuai Yuan, Yanjun Li

"In order to improve recovery efficiency of iron minerals from iron ore tailings and to reduce its connected environmental pollution, this article investigated the reducing roasting of iron ore tailing in a laboratory fluidized magnetization roasting reactor to optimize the roasting method and conditions. The examined parameters included roasting temperature, roasting time and reducing atmosphere. The parameters evaluating magnetizing roast efficiency and theoretical value were determined. X-ray diffraction (XRD) analysis was used to investigate the conversion of iron phase after roasting. The results show that the best magnetizing roast conditions are roasting temperature of 540?, holding time of 15min, and CO concentration of 20%. The magnetization conversion ratio of roasting products is over 80%, under the best magnetic separation condition, the concentrate grade of iron is 65.61 % and the recovery of iron is 83.77 %. The XRD analysis shows that Fe exists in hematite and siderite before roasting and exists in magnetite after roasting. The technique not only recovers the iron minerals from tailings with good economic benefit, but also reduces the environmental pollution of tailings accumulation.INTRODUCTION Iron ore tailings are the solid wastes generated during the beneficiation process of iron ore concentration and are one of the main pollution concerns in the mining industry (Das et al., 1996). Continuous development of the iron and steel industry has led to the increasing amount of iron ore tailings; there are over 300 million tons of iron ore tailings discharged per year (Rao et al., 2016). The huge amount of stockpiled iron ore tailings brings a series of environmental and social problems. Comprehensive utilization of iron ore tailings can not only reduce environmental load but also conserve resources, promoting sustainable development of the society. In recent years, iron ore tailings as secondary resources have received considerable attention in many countries in the word and numbers of studies on utilization of iron ore tailings were carried out, such as recycling the valuable minerals (Datta et al., 1996; Jia et al., 2013; Panda et al., 2018), used in construction material compositions as alternative source of raw materials (Das et al., 2012; Zhou et al., 2012; Luo et al., 2016) and other utilization. The iron minerals were recovery by magnetization roasting (Rao et al., 2016; Yang et al., 2013; Yang et al., 2011) and flotation (Kumar and Mandre, 2016). By comparison the reduction roasting has more advantages, but it was found that the conventional roasting equipment was inefficient, high energy consumption and un-economically applied on an industrial-scale."

Jan 1, 2018

By W. Yao, M. L. Li, R. Cui

"The purpose of this research is providing a flotation process for recovery of lead in lead silver residues from a zinc smelting plant with a new hydroximic acid collector (HOC). The collecting ability and reaction mechanisms of HOC were investigated based on pure mineral flotation tests and analysis of zeta potential. The pure anglesite flotation tests showed that HOC has a good collecting ability for anglesite. Zeta potential measurements proved that HOC adsorbed on anglesite surface physically and chemically. The lead-silver residues in a zinc smelting plant with lead grade about 17.5% was used as raw material for flotation tests. The results showed that under the conditions of pH adjusting agent lime 500g/t, inhibitors sodium silicate 2000g/t, collector HOC 1500g/t, frother alcohol oil 75g/t, the grade of the lead concentrate can be reach 47.18% and the recovery was 76.39% by one roughing-one scavenging-three cleaning and middles back to the flow-sheet in turn after the lead-silver residues were washed by two stages of cleaning-filtration.INTRODUCTION Nowadays, with the increasing exploitation of natural mineral resources, more and more secondary resources should be researched and used for the valuable metals. Hydrometallurgical zinc leaching residues, which contain a considerable amount of zinc, lead, silver and other minor valuable constituents, is a typical and abundant secondary resources (Zhang et al., 2011). A huge quantity of zinc leaching residues (ZLR) had been produced per year (Jiang et al., 2017).This residues not only occupy precious land but also threaten the environment because of the dissolved heavy metals especially in rainy days (Han et al., 2014). Consequently, it is urgent to develop an effective and clean method to dispose this residues which can benefit not only in economical but also in environmental (Jha et al., 2001)."

Jan 1, 2018

By Peter Kondos

The need for a sustainable development of ore deposits makes it imperative to be innovative and mindful in creating an economically and environmentally viable operation, while maintaining a good working relationship with the various stakeholders involved in developing and operating a large and complex mining project. This is becoming immensely important as gold ore deposits are becoming more mineralogically complex along with lower grades presenting both metallurgical and environmental challenges that need to be addressed in mitigating risks and improving project economics. This paper presents Barrick?s approach to development of strategic technologies for our long-term sustainable growth through conversion of valuable resources into reserves for both our green-field development projects and the expansion of our existing mining operations. Some of the key strategic solutions, including mineral processing, metallurgical and energy technologies, developed by Barrick and their impact on some of our complex gold and copper-gold ores will also be discussed in this paper. Keywords: gold ores, copper-gold ores, processing, breakthrough technologies

Sep 1, 2012

By Lilong Huang, Yuan Long, Li Shi, Guowang Zhang, Xiao Xiao

"Graphite is the key raw material of new carbon materials such as graphene and spherical graphite. The size and completeness of graphite flakes directly affect the performance of new carbonaceous materials.The research aims to increase the yield of large flake graphite by way of preventing the flake graphite from being damaged during the grinding process. A series of grinding and flotation studies on the flake graphite samples of Yichang in Hubei Province were carried out by vertical stirred mill . The damage coefficient L characterising the degree of graphite flake fractured and corresponding formula was proposed to determine the quality of the grinding and grinding of the flake graphite. The way the damage coefficient L of graphite flake would be affected if with different mill, different media material and size, stirrer speed were investigated. The test results show that vertical screw stirred mill helps the protection of large flake of graphite as well as the graphite liberation. When grinding to the same fineness, the damage coefficient L of graphite flake is 1.20 for vertical stirred mill, while the damage coefficient is 2.93 for ball mill. Minimum damage coefficient of graphite flake was obtained when using 6 mm polyurethane coated ball as grinding media, under the condition that rotation speed of the stirrer within the range of 100~130r/min. The grade of graphite in the concentrate floated from the ground product was 94.16%, the rate of recovery for graphite was 94.66%, and the content of +0.15mm was 54.83%.1 INTRODUCTION Flake graphite is a very important non-metallic mineral[1,2],and due to its special flake structure, the greater the scale and the higher the C grade, the value of its application is larger too. Therefore, in the grinding of graphite sorting process, We should minimize the destruction of graphite scales.. In this paper, graphite mine in Yichang, Hubei Province was used as the raw material for the study. Rough concentrate with C-grade of 36.49% was prepared by rough grinding and coarse separation. Then a series of grinding and flotation studies on the rough concentrate were carried out by vertical stirred mill , which aims to increase the yield of large flake graphite and to provide technical support for improving the beneficiation process of graphite ore."

Jan 1, 2018

By Liu Jie

Refractory iron ore deposits in China have various genesis and complicated types, the nature of which is poor, fine-disseminated and complex. Therefore, refractory iron ore could scarcely be separated and utilized by traditional mineral processing technology at present. It is necessary to explore deep reduction technology to change the characteristics of refractory iron ore and to use effectively the iron resource. And deep reduction technology is that on the condition of higher reduction temperature than that of magnetic roasting and stronger reducing atmosphere, the iron oxides from iron ore was reduced to metallic iron particle that is easy to dissociate. And then production from deep reduction is easily separated by magnetic separation and iron powder production was obtained finally. Deep reduction technology for Lingyang iron ore from Jilin, China, as the refractory iron ore, was studied in this paper. The influences of such main factors as reduction temperature, time and coal content were investigated. The results showed that the Metallization rate of reduction product was up to more than 90% under optimum conditions, and then higher iron grade and recovery of reduction iron powder were obtained from subsequent magnetic separation. Furthermore, the deep reduction mechanism in the system was studied by the means of XRD and SEM analysis for reduction production and Physical Chemistry of Metallurgy. Analytical results indicated that during deep reduction, the size of iron particle from deep reduction materials was increasing as reduction temperature rising and reduction time extending. The growth of metallic iron particle from deep reduction production was divided into such three stages as reduction nucleation, deep reduction and growth of metallic iron particle.

Sep 1, 2012

By M. L. Wu

A moderately thermophilic acidophiles strain had been isolated from the bio-heap leaching plant in Zijinshan Copper Mine, and the identification based on the PCR-16S rRNA gene sequence homology analysis with morphologic and physiologic methods was conducted by polyphasic taxono-my and phylogeny research. The results show that the strain by depurated belongs to Acidthiobacillus genus and is considered as Acidthiobacillus albertensis.

Jan 1, 2014

By F. H. Wang

The Yinmao Lead-Zinc Mine Co. Ltd. has got 50 years of mining history. In recent years, the manganese grade in the flotation tailings has been continuously increasing. In order to make fuller use of the existing resources, as well as to increase the company?s economic efficiency, our company adopted the technique ?magnetic separation? and ?iron removal? to effectively recycle the manganese concentrate resources.

Jan 1, 2014

By W. Rubarth

The kaolin losses in hydrocyclone classification are determined by the fines, which are discharged together with the water to the underflow. This paper presents an improved technique of water injection to the conical part of the cyclone applied especially for small cyclones in kaolin preparation. In small hydrocyclones water, injection is a sensitive process. Therefore, the process was stabilized by controlled water injection dependent on the measurement of the underflow shape. Three applications of this innovation are presented. In the first case, the water injection is applied for the separation stage in dilute suspension where the final product is produced in the overflow of a 50mm hydrocyclone. The underflow contains sand and residual kaolin. For a higher kaolin recovery, the underflow is usually treated downstream in washing cyclones. The wash water injection results in a 45 ? 50% - reduction of the kaolin fraction <25µm in the underflow. Thus, water injection to the classifying cyclone leads to a separation comparable with a downstream washing stage. An additional hydrocyclone stage can be deleted. The second application refers to a classification in dense suspension. Here, the underflow of the last hydrocyclone stage was directed to a washing in a 50mm hydrocyclone. The additional injection of 3L/min water in to the conical part of the cyclone reduced the kaolin losses by half.The third application was executed in the washing stage equipped with 75mm hydrocyclones where the underflow is directed to flotation. Using the water injection the kaolin recovery in this stage was increased by approximately 20%. Keywords: hydrocyclone, classification, kaolin beneficiation, water injection, underflow washing

Sep 1, 2012

By Qidong Zhang, Yongsheng Song, Wenjuan Li, Guiying Zhou, Kun Song

"Molybdenum is a very important rare mineral resources, which exists largely in oxidized ores and sulphide ores in nature. About 99% of metallic molybdenum comes from molybdenite. The talcose molybdenum resources are abundant but the resources utilization is low, because the talc is naturally hydrophobic and the floatability of talc is similar with molybdenite, which lead to difficult separation by flotation. Talc is easy entry into concentrate in flotation which can cause the content of MgO overhigh, therefore the molybdenum concentrate grade can not meet the industrial requirements. Thus the utilization level of talcose molybdenum resources has been restricted greatly.The adsorption of water on talc and molybdenite surfaces and natural floatability of minerals were studied by density functional theory method. The results showed that molybdenite and talc were layered minerals which exhibited similar surface wettability and H2O molecule prefers to stay with water rather than the minerals surfaces. N2 is adsorbed on talc and molybdenite surfaces more easily than H2O. The interaction and flotation behavior were studied by SEM and flotation experiments. The reason why talc interferes with the flotation molybdenite has been revealed. The agglomeration between molybenite and talc was caused easily in neutral or acidity solution, and it was dispersing between molybenite and talc particles in alkaline solution. The flotation results showed that good floatability of talc was the key factor causing a low grade of concentrate in alkaline solution. Thus, it is the key factor to enlarge floatability difference between molybdenite and talc.INTRODUCTIONMolybdenum is a kind of important rare metal and strategic reserve resources (Zhitao Y et al, 2016a). Due to excellent characteristic, such as high melting point, good thermal property and et al, it’s widely used in metallurgy, machinery, chemical, aerospace, and many other areas. It has become an indispensable metal in modern industry. Molybdenum generally exist in the form of molybdenite which is a kind of mineral with excellent natural floatability. Talc is a kind of typical hydrous and layered magnesium silicate minerals (Beattie D et al,2006a), which is one of the most common gangue mineral of the platinum group metal ores and metal sulfide ores (Tao L et al,2011). Due to its good native floatability, talc is easy entry into the concentrate product with foam in the process of sulfide ore flotation (Kelebek S and Smith S, 2006b), which resulted in decreasing concentrate indexes. Not on that, the high-content MgO of concentrate will also produce a series of adverse impact to the subsequent smelting (Lotter N O et al, 2008). Therefore, it is difficult to separate talc from sulfide ore concentrate effectively."

Jan 1, 2018

By Gaom M. W.

The Mount Isa copper concentrator started operation in 1973. Its secondary grinding circuit consisted of two 5 meters diameter ball mills in closed circuit with 505 mm cyclones. At the design throughput of 800 t/h, the 80% passing size of the circuit product (P80) was about 140 µm. The then Mount Isa Mines Limited (?MIM?) installed two autogenous grinding (?AG?) mills in 1991 to replace two stages of crushing, a rod milling stage and one primary ball milling stage. One of the AG mills was later converted to semi-autogenous grinding (?SAG?) operation by the addition of a steel grinding medium to achieve the designed plant throughput of 800 t/h. The cyclone over-flow P80of the secondary ball mill circuit was reduced to 120 µm by the increased operating power in the AG/SAG mill circuits. The two secondary balls mills had a grinding power of 5.2 MW. A mineralogical study of the milled products indicated that half of this grinding power was sufficient for adequate chalcopyrite liberation. Eliminating one of the secondary ball mills could reduce energy and operating costs by more than A$2 million dollars per year. An optimisation project team was established to achieve the predicted power saving. Grinding circuit simulations were conducted for different circuit configurations. Ball mill parameters such as ball size, ball charge and feed slurry density were optimised. Cyclone body diameter, spigot and vortex finder sizes, and cyclone types were tested. The secondary ball mill circuit was redesigned and several proposed circuits were run as trial production campaigns to determine their operability and efficiency. The plant trials confirmed that one of the secondary ball mills could be decommissioned. Significant cost savings were achieved as a result. The success of the project demonstrates optimising grinding circuits can not only deliver the plant performance, but also a much lower unit operating cost through energy and maintenance savings.

Jan 1, 2014

By L. Tong

Stirred milling of laterites offers possibilities for improving liberation and selective size reduction of soft nickel-bearing minerals in laterites. Batch grinding tests were performed in a Netzsch LME4 stirred mill on a siliceous goethitic (SG) nickel laterite sample (-2000 µm particle size) to evaluate the effect of operating conditions such as stirrer speed, grinding time, pH, solid content, water salinity and charge volume. The target was to produce a -38 µm fraction in the milling product with high nickel recovery and grade. Addition of dispersant (sodium hexametaphosphate) was also optimized with respect to the rheology of the slurry. In terms of stress intensity, the optimum grinding conditions for selective size reduction were: 1000 rpm, 50 per cent charge volume. At higher stress intensity (2000 rpm), Ni recovery in the -38 µm product was higher, but Ni grade was low, due to the breakage of the harder siliceous particles. Decreasing the yield stress by modifying slurry pH or adding dispersant improved the rheological properties of the pulp, but had no great influence on Ni upgrade in the fine product. Modifying water salinity by adding 2 M NaCl had also little effect. The breakage of the +38 µm particles in the feed determined Ni upgrade greatly. Ni grade in the -38 µm product decreased with grinding time, suggesting that the Ni-bearing minerals break first, while the harder siliceous minerals have a lower breakage rate. The breakage rates with respect to sample mass for Ni, Mg and Si indicate that: Mg > Ni > Mass > Si. The optimum grinding time for the highest Ni upgrade was 0.25 min. The Ni grade increased from 0.88 per cent to 1.35 per cent (upgrade 54 per cent), with 24 per cent Ni recovery. Keywords: fine grinding, stirred media mill, nickel laterite, slurry rheology

Sep 1, 2012

By V. I. Ryaboy, V. P. Kretov, S. E. Levkovets, I. V. Ryaboy

"Using the flotation of a gold-containing ore from a deposit in Kazakhstan as an example, we have conducted a study designing dialkyldithiophosphate collectors, in addition to xanthates, for the flotation of hard-toenrich gold-containing ores to increase gold recovery.The increased flotational ability of the dialkyldithiophosphates was determined by their surface activity at the liquid-gas interface and their hydrophobic ability, the changing of which allowed us to control the collecting power and selective ability of the dialkyldithiophosphates. The studying of the surface activity of aqueous solutions was done using the stalagmometric method and the evaluation of the hydrophobic ability was done in percentage of the relative value of the zinc ion binding in the solution in standard conditions.Studying the influence of surface activity in our designed dialkyldithiophosphate collectors, with their close hydrophobic ability, showed that even with a small increase in surface activity in their aqueous solutions, gold recovery increased by 2-3% in laboratory conditions. Using this enabled us first to apply the dialkyldithiophosphate collector BTF-161 at a plant in Kazakhstan, and then to introduce the specially designed dialkyldithiophosphate collector BTF-163, which has been in use since. Further study of dialkyldithiophosphate activity based on this concept showed us that for the range of short-chain dialkyldithiophosphate collectors with a chain length of up to ?5, the effectiveness of ore processing became lower the higher their surface activity got, with relatively small differences in their hydrophobic ability. For long-chain dialkyldithiophosphates with a chain length of over ?5, ore processing effectiveness increased with the increase of their hydrophobic ability.Based on these studies, a new effective dialkyldithiophosphate collector, BTF-1517, was designed. Using this reagent in continuous gold recovery tests allowed us to reach an 84.21% recovery with a concentrate quality of 15.66 g/t, while using the applied collector BTF-163 in similar conditions led to the recovery of 82.87% with a concentrate quality of 15.65%. As a result, the Kazakhstan processing plant decided to conduct industrial tests with the BTF-1517 collector."

Jan 1, 2018

By T. Bhambhani, O. Yavuzkan, D. R. Nagaraj

"The recovery of oxide Cu minerals by flotation is a longstanding challenge in the minerals industry, especially for high acid-consuming ores which would not be economical for direct acid leaching. Sulfidization (often using controlled potential sulfidization or CPS) using NaSH (or Na2S) followed by flotation using traditional sulfide collectors is the widely used technique. CPS has certain limitations: a) inability to recover certain oxide Cu minerals because they are refractory to sulfidization, b) high consumption of NaSH (or Na2S), and c) potential health and safety hazards associated with NaSH (and Na2S). Flotation of oxide copper minerals using alkyl hydroxamate (AHX) collector has been studied extensively. Investigations using single minerals and laboratory ore flotation have been conducted in the past to demonstrate the efficacy of alkyl hydroxamates. The technology has been used intermittently in plants. One of the main challenges in plant use has been quantifying the true potential for alkyl hydroxamates for recovery of various oxide Cu species in complex and variable ore systems and identifying the most suitable conditions for optimal use. Quantitative mineralogical analysis using QEMSCAN was used in this study to characterize flotation products lab flotation samples. Analysis of concentrates and tails from hydroxamate flotation and CPS flotation stages demonstrated that certain oxide Cu minerals respond exclusively to alkyl hydroxamates and not to CPS. The hierarchy of interaction of AHX with the various oxide Cu minerals could be inferred from these studies. Finally, these studies also allowed quantification of a group of minerals species, which (erroneously) report as part of the Acid-Soluble Cu [ASCu] but cannot be recovered by flotation, thereby facilitating an estimation of the true recovery potential for alkyl hydroxamate.INTRODUCTIONCopper that is economically recoverable occurs in three major types of ores, which are defined by the modal mineralogy of Cu. For sulfide ores, Cu occurs as sulfide minerals and is satisfactorily recovered by flotation using sulfide collectors. Non-sulfide ores, which contain Cu in the form of oxides, phosphates, carbonates and silicates, described in the industry as “oxide” ores (or ores containing “acid-soluble” Cu or ASCu), are currently treated using hydrometallurgy, which involves leaching with dilute sulfuric acid followed by solvent extraction and electrowinning, unless the ores contain acid consuming gangue minerals such as dolomite. For mixed sulfide-oxide ores (i.e. containing both sulfide and oxide Cu minerals) that do not contain acid consuming gangue minerals, Cu values are easily recovered by flotation of sulfide Cu minerals followed by leaching of oxides (only when a leach plant is available). However, when the ore contains acid consuming gangue minerals flotation is required to recover both sulfide and oxide Cu minerals."

Jan 1, 2018

By L. S. Zhou

HermesTM metal magnetic liner (MML) has been invented and manufactured by China Metallurgy and Mining General Co. (CMMC). This paper describes its mechanism, structure, magnetic field distribution, application, economic benefit and safety performance. The 10 years? service life in Benxi Steel?s Waitoushan Mine, along with 6 years? technological analysis on its application in 5500mm×8800mm (diameter × length) ball mill in Anshan Steel?s Diaojuntai mineral processing plant, has proved its advantages such as super reliability, long service life, light weight, thin thickness, low noise and short payback period. It has also demonstrated its positive effects on the grinding process such as high productivity, energy-effective performance and low consumption of grinding media. It reduces labour intensity and improves working conditions, due to its easy installation, free maintenance and the fact that it doesn?t require fastening bolts or cause slurry leakage. It is de-signed scientifically in accordance with the varieties of processing lines, mill specification, ore type and grinding media, and has been applied in different grinding processes for magnetite, hematite, gold ores, nonferrous ores and other materials. HermesTM MML has three types of products: General, Composite and Heavy-duty. They are designed to meet the requirements from customers in China and abroad. So far, more than 400 sets of MML have been applied in ball mills with diameter rang-ing from 1500mm to 5500mm. It has become highly popular in American market recently due to its safe and effective performance.

Jan 1, 2014

By G. Alfano

This investigation is concerned with the optimization of ultrafine grinding of solids. It is focused on a dynamic classifier for recovering the fine fraction, for automatic recycling of the oversize particles and for reducing power consumption. Power consumption plays a major role in these energy intensive processes and depends on several parameters such as nature of the solid, degree of fineness of the finished product and, above all, grain size of the feed. This study indicates the optimal conditions for a dynamic classifier, that is, geometric characteristics of the apparatus and its capacity, inlet air flow rate and dimensions of the classification circuit. It is also shown that a mean grain diameter (dm) of about 2.00 µm with top size (dmax) of 50 µm can be achieved with an imperfection value of below 0.40 and energy consumption of 215 kWht-1. Keywords: air classification, dynamic classifier, jet mill, energy

Sep 1, 2012

By K. C. Corin, M. S. Manono, R. M. Manenzhe, J. G. Wiese

"Environmental concerns necessitate the recycling of process water within mining operations. Given that recycled water is chemically different from fresh water, and collectors are added such that they adsorb at the liquid-particle interface, changes in the aqueous phase are expected to affect collector adsorption. A Finnish nickel-copper ore was floated in synthetic plant waters of varying ionic strengths and plant waters obtained at Boliden Kevitsa Mine, with aerophine and sodium isopropyl xanthate as collectors. Of the tested waters, the copper thickener overflow was the least conducive to xanthate adsorption and valuable mineral recovery. The nickel thickener overflow, standard process water, and raw water were the most conducive to xanthate adsorption. For the raw water and nickel thickener overflow, increased adsorption correlated with increased valuable mineral recovery. Further, recycling xanthate retained in water affected the selectivity of the collector and hence the concentrate grades.INTRODUCTIONFlotation is a separation process that exploits the differences in the surface properties of the particles being separated. The efficiency of separation is dependent on the degree of hydrophobicity achieved by the particles meant to be floated, which are, in most cases, valuable minerals. The hydrophobicity is in turn dependent on the adsorption of the chosen collector onto the surfaces of the floated particles (Fuerstenau, 1984; Taggart and Hassialis, 1946). Empirical findings suggest that species dissolved in solution strongly influence collector adsorption and overall flotation response (Fuerstenau and Chander, 1986). Due to environmental concerns, it is becoming more pertinent for mining plants to recycle process water and hence limit the usage of potable water. There is an interest to ensure minimal discharge of plant water into the environment, as this water is typically polluted with process reagents that may render it toxic (Levay et al., 2001)."

Jan 1, 2018

By Jacek Kolacz

"Comex has carried out an extensive research work related to optimising sensor based sorting systems. The main target was to achieve efficient separation and maintain high capacity of the process. Eventually, the operating cost of the sorting process was investigated in terms of potential industrial applications and possible replacement of the existing traditional processing equipment. The study included an influence of the following factors on the separation efficiency: capacity, particle size and distribution, particle shape, material properties like colour, density and composition, as well as percentage of the rejected fraction. The above factors were also considered in the calculation models for the operating cost of the sorting process. In addition, other elements were considered like compressed air cost, cost of energy, labour cost, and necessary service and maintenance cost. All these elements were implemented into the calculation model allowing quick and effective evaluation of the major parameters for sorting applications. Finally, the study was carried out for two popular sorting principles: visible light sorting utilising differences in color, texture and shape and X-ray sorting using differences in density and chemical composition. GENERAL INFORMATION ABOUT SORTING POSSIBILITIES Application of the sensor based sorting systems, without any doubt, brings a lot of possible advantages in many mineral operations. The main advantage of the new system is related to its universality and at the same time very sophisticated image processing functions, which can be carried out in the same processing unit (Kolacz, 2014). Figure 1 shows the CXR-1000 system from Comex with 1 m belt width, in the configuration where many different analysed parameters can be used to provide particle separation. The image analysis system includes a camera installed either over the transport belt conveyor or at its discharge end. The system includes the X-ray attenuation analysis realized by the XRT system in the central part of the conveyor belt. The sorting system can be used with both optical and XRT analysis or separately depending on an application."

Jan 1, 2018

By V. F. Petrov, O. D. Khmelnitskaya, V. M. Lodeischikov

"The processing of copper gold ores is one of the major issues of gold-mining industry in the beginning of 21st century. In this case, application of ammoniacal cyanidation process for this type of mineral raw materials deserves special attention. Irgiredmet Institute has carried out a wide range of studies on ammoniacal cyanidation process and evaluated the possible commercial use of this process for Russian operating plants. Copper gold-bearing ore from a current Russian deposit was studied. The content of gold and copper in the ore is 9.4 g/t and 0.4%, respectively. Based on the results of preliminary test work, a flow sheet was developed. It included gravity concentration followed by cyanidation of the gravity tailings using CIP. The flow sheet provides sufficient total gold recovery (91.5%). However, this technology has disadvantages, such as high specific consumption of reagents: 4.5 kg/t NaCN and 13.5 kg/t Ca(OCl)2 the ore and the increased gold grade in the liquid phase of the tails slurry (0.2 g/t). In order to improve cyanidation process parameters, test work on gravity tails processing using ammoniacal cyanidation was carried out. After the test work was completed, ammoniacal cyanidation flow sheet for copper gold-bearing ores was developed. Leaching conditions were optimized using recycled process solutions. Recommendations on gold recovery from the solutions and tails detoxification are given. The proposed flow sheet provides 91.5% gold recovery. In this case, compared to the conventional option, the consumption of cyanide decreases by 3-4 times.INTRODUCTION The technology of precious metals recovery from gold-bearing ores is based on cyanidation. This accounts for up to 90% gold recovery and the significant portion of silver (Lodeischikov, 1999). However, there exists the category of so called refractory ores. They are not amenable to direct cyanidation (without using additional expensive processes), or they are characterized by low indices of metals recovery and high consumption of reagents. The latter also include copper gold ores. Their deposits can be found extensively both worldwide and in Russian Federation. A feature of these ores is that they contain not only gold but also copper. It is considered not only as a valuable component but also as a harmful mineral impurity that hinders gold cyanidation, gold precipitation from the solutions by cementation onto zinc dust and adsorption onto activated carbon (CIL, CIP-processes), detoxification of cyanide bearing effluents."

Jan 1, 2018

By L. E. Veki, S. M. Luukkanen, J. P. Karvonen, J. O. Leppinen

Today there is a consensus that xanthate adsorption on sulfide minerals is primarily controlled by redox reactions occurring at specific potentials on these semi-conductive minerals. Consequently, it is possible to control xanthate adsorption by controlling electrochemical conditions in the system by using oxidizing and reducing agents. The scope of this study was to investigate the possibilities to increase the selectivity of Cu-Fe-Zn ore flotation by applying electrochemical control in the conditioning of the flotation feed. In this work, mild steel grinding in a nitrogen atmosphere was used as the basis to provide a negative starting potential and minimize the amount of oxidation products on sulfide mineral surfaces. To study how different potential levels affect flotation results, a controlled conditioning procedure was utilized maintaining potential at a desired level by titrating the pulp with air. Xanthate adsorption kinetics during conditioning was examined by taking pulp samples for spectrophotometric analysis and laboratory flotation tests were conducted for samples that underwent the controlled conditioning procedure in the potential range of -200mV to +200mV vs. SHE. A clear correlation was detected between chalcopyrite recovery and the potential during controlled conditioning indicating that there was a constant increase in chalcopyrite recovery when the potential was shifted to more anodic values. It is possible that utilizing potential control in the conditioning stage, a smelter grade copper concentrate can be achieved directly in rougher flotation without cleaning stages. Conditioning in favorable conditions had significant positive effects on flotation selectivity of chalcopyrite. The improvement in copper concentrate grade being predominantly caused by the depression of pyrite. By applying the controlled conditioning procedure pyrite recovery in rougher flotation was reduced even low as under 1%, while in the tests without controlled conditioning, pyrite recovery varied between 7.5 – 65.7%. The result of this work indicate that affecting collector adsorption by electrochemical control in the conditioning stage can provide significant improvement in sulfide mineral flotation and industrial applications could lead to decreased chemical consumption, reduced equipment and maintenance costs.

Jan 1, 2018

By Nikkam Suresh

Dense medium cyclones have been in use for washing coarse and small coals for more than 50 years. There have been modifications in its design and today these units have become indispensable for washing of Indian coals possessing difficult washing characteristics. About 53 percent of the Indian coals (coking and non-coking) are being washed in jigs, about 38 per cent are washed in dense medium cyclones while the remaining 9 per cent is treated in other units like Barrel Washers, Heavy Media Baths and Drum Separators etc. The present paper deals with the attempts made for design of industrial Dense Medium Cyclones for enhanced coal recovery. Two industrial units of 500 mm diameter and 650 mm diameter were designed with their washing capacities being 200 m3/hr and 350 m3/hr, respectively. The results of the pilot tests conducted on 500 mm cyclone treating very high Near Gravity Material coals crushed to -3.0+0.5 mm gave an ash reduction of up to 19.5 percent with the new design i.e., from a feed ash of 34.5 percent to 15.06 percent in clean coal with an appreciable yield of 45 percent in one stage.

Sep 1, 2012