Search Documents

By L. X. Zeng

The low-grade nickel resource is very abundant in the western China. To make the best of the low grade nickel ore, we studied the process mineralogy and beneficiation process of nickel ore in the Yangliuping of Sichuan province. The grade of nickel is 0.45% in the nickel ore and the nickel exists in the sulfide including pyrrhotite, nickel pyrite, chalcopyrite primarily. The nickel distributes in pentlandite and magnetite over 90% and the copper does in the chalcopyrite over 95%. The carri-er minerals of useful elements tend to concentrate in space for concentration. As is shown in grain-size analysis of three major minerals, there are some more fine-grained grains with the percent of from 10% to 15% (<40 µm) and from 3.5% to 5.5% (<20 µm). So there will be some smaller size disseminated sulfide minerals difficulty to liberate in the process of concentration. The liberation degree of sulfide is not high and there are much associativity in the sulfides. Therefore, we should reclaim the sulfide aggregation dominating as pentlandite when concentrating. In addition, the sulphide minerals is so brittle that we should take care of preventing from crashing when grinding. The gangue mineral is mostly metamorphic mineral including serpentine, chlorite and amphibole which is easy to be argillization and difficult to concentrate.

Jan 1, 2014

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

"The morphology of pellet feed is known to influence several properties of iron ore pellets, including drop number, compression strength and reduction properties. The effect of grinding method on the particle size, specific surface area and particle shape of an iron ore concentrate has been studied. Grinding methods considered were ball mill and high pressure grinding rolls (HPGR). 5 different samples (Blaine= 1800, 1900, 2000, 2100 and 2200 cm2g-1) were used to compare the size, shape and specific surface of particles for each grinding methods. Particle size was meticulously examined by sieve analysis, laser sizing and image analysis. In samples ground by ball mill, it has been observed that the fraction of particles <10µm increases from 39% to 46% as the Blaine number increases from 1800 to 2200 cm2g-1. For HPGR samples, corresponding figures are 41% and 49% respectively. It is evident that for samples ground by HPGR, the fraction of fine particles is higher than that of those ground in the ball mill. To measure the specific surface area of particles, Blaine and BET were used. A higher real surface area was observed from HPGR treatment in comparison to ball mill grinding, provided by a higher porosity, cracks, roughness and new surfaces. Shape factor of particles was determined using three descriptors: circularity, roughness, and aspect ratio. It was also observed that particles produced by HPGR were more elongated, less circular, and rougher than those processed by the ball mill. 1. INTRODUCTION Particle size and shape are important parameters that can significantly affect mineral processing plants and pelletizing plant performances (Brozek and Surowiak, 2007). It has also been proposed that green pellet quality is directly related to the amount of fine particles in a pelletizing plant (Dwarapudi et al., 2008; Umadevi et al., 2008; Gul et al, 2014; Van der Meer, 2015). Particle size distribution and specific surface area (SSA) are also key factors that can control the quality of green and fired pellets. Processing circuits generally reduce the fines fraction to lower than the required specific surface area (SSA). It is therefore necessary to regrind concentrates to produce suitable pellet feed for further treatment in the balling and firing steps [1, 2]. Two main methods are used for re-grinding of concentrate; high pressure grinding rolls (HPGR) and ball mill. Given the different forces used to reduce size in these methods, it is expected the shape of particles will be different (Pourghahramani and Forssberg, 2005)."

Jan 1, 2018

By F. S. Niu

With the feature of finely-dissemination particle and complex mineral composition, oolitic hematite is considered to be the ore dressing difficult problem in the world. Series research on refractory oolitic hematite in Zhangjiakou Area are introduced as following: ore properties?technology mineralogy and mineral processing technology. The survey shows: with the fine grinding of the hematite to a fineness of -0.076mm 95%, obtaining iron concentrates grading 62.74% Fe at the recovery of 46.80% by high intensity magnetic separation- reverse flotation flowsheet; under the three stages intensity magnetic separation,four stages grinding and four stages gravity separation, getting the iron concentrates grading 61.09% Fe at the recovery of 45% using high intensity magnetic separation- gravity separation flowsheet; with roasting temperature of 800°C, time for 75~90min and ore-coal ratio of 11, gaining the iron concentrates assaying 62.74% Fe at the recovery of 87% by roasting- magnetic separation flowsheet. At present, this research is still doing for the target of raising the concentration recovery on the base of high grade concentrate. It is in the hope of fully utilizing the existing hematite resources in Zhangjiakou

Jan 1, 2014

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

Green pellet strength including drop number and green compression is highly depended on particles size and shape. The used grinding method, ball mill or high pressure grinding roll (HPGR), directly vary the particle size and shape. Considering mode of pellet crack, green pellet is composed of particle-binder-moisture system. Different type of forces existed in such a system to create a stable green pellet: solid particle interaction, magnetic, binding and cohesive forces in the interface of particle-moisture. The pellet failure can occur at solid-liquid interface and/or through liquid phase. Pellet crack occurs when crack passed through entirely the plane failure. In this research, the effect of particle size and shape of pellet feed on green pellet strength has been investigated. It was deduced that green pellet strength highly improved by increase of specific surface area. The drop number and green compression strength of pellets prepared by HPGR was higher than ball mill. It was found that the main reason responsible for this difference was the particle shape. Capillary force is responsible for part of pellet force and improves by decrease of particle size. Also more elongated shape of HPGR particles resulted in higher capillary force due to thinner interface layer between particles. The less circular shape of particles lead to improvement of capillary force as can be occurred for HPGR particles. The rougher shape of HPGR particles resulted in higher wettability of particles and better diffusion of water among particles. In fact the rougher particles means lower connection angle. Aspect ratio of particles was of great importance of crack growth because the required energy of pellet failure increases directly. The required energy for pellet failure increases by increment of particle aspect ratio. The relationship among crack failure force, roughness and aspect ratio has been modeled considering 3 shape descriptors.

Jan 1, 2018

By Zhang Zhonghan

A domestic tungsten-tin ore presents very complex property. How to effectively recover the scheelite, wolframite and cassiterite in the ore has long been a difficult problem to be solved urgently. On the basis of process mineralogy study, a main flow-sheet for effective recovery of tungsten-tin minerals has been developed, which including ?fine grinding of feed?bulk flotation of all sulfides followed by their selective separation?iron recovery by LIMS?tungsten-tin minerals bulk flotation using new technique developed by our institute?tungsten-tin recovery by gravity from above tungsten-tin bulk flotation tailings?. As for the treatment of tungsten-tin bulk rougher concentrate, several flow-sheets of tungsten-tin separation by direct hydrometallurgy or a flow-sheet consisting of scheelite cleaning at elevated temperature followed by the gravity separation of scheelite cleaner tailing?separation of wolframite from cassiterite by dry HIMS or by direct hydrometallurgy are developed. For a low grade head ore, all valuable sulfide, magnetite, scheelite, wolframite and cassiterite are recovered with satisfactory in lab scale test. Keywords: micro-fine cassiterite, tungsten-tin bulk flotation, gravity separation-flotation-dry HIMS combined flow-sheet, hydrometallurgy

Sep 1, 2012

By G. B. Abaka-Wood

"The versatility of froth flotation has made it vital in the beneficiation of rare earth elements (REE) minerals from either high or low grade ores of complex mineralogy. There has been a significant increase in the tonnage of rich iron oxide tailings obtained from extraction of primary commodities such as copper and gold in Australia, which have been identified to have very low grade rare earth oxides (REO) (= 1%). There is a vast knowledge gap in the upgrade of REO from such tailings. The aim of this research is to investigate the feasibility of the use of fatty acids for the upgrading of REO from selected iron-oxide rich tailings. Two forms of fatty acid collectors (oleic acid and sodium oleate) were employed in this investigation. Bench scale flotation tests were carried out using a Denver D-12 cell.The effects of pulp pH, fatty acid dosage, particle size distribution (-150 +75 µm, -75 +38 µm and -38 µm) and conventional depressants (sodium silicate and starch) dosage on flotation recovery of REO were investigated. A comparison of the flotation results indicated that sodium oleate was the more efficient fatty acid for REO flotation at all the pulp pH investigated. The flotation performance is demonstrated to be particle size-dependent. The results on the effect of depressants dosage indicated that both sodium silicate and starch were unselective in reducing the recovery of hematite (Fe2O3) and quartz (SiO2) with corresponding decrease in REO recovery. Generally, Fe2O3 and SiO2 formed substantial contents of the flotation concentrates obtained, both in the absence and presence of depressants, which indicates liberation is a major challenge in achieving selective REO upgrade and recovery.The flotation tests carried out on the iron-oxide rich tailings suggest the possibility of REO upgrade using fatty acids, although particle size distribution and minerals liberation are key limiting factors in achieving selective REO upgrade and recovery."

Jan 1, 2018

By H. R. Manouchehri

Sustainable development requires the optimal use of natural resources and recycling of the wastes. In fact recycling is the final productive use of obsoletes. ELVs, obsolete appliances and industrial wastes have become important resources for production of iron and steels, non-ferrous metals, and composites. Within shredding plants, these obsoletes are firstly shredded to the pieces and then processed to recycle different materials, especially ferrous and non-ferrous metals for metallurgy. Traditional and new developed mineral processing technologies are nowadays used for recycling different materials from waste effluents. Shredding and separating plants are currently recycle the wastes by make use of different technologies to mainly produce raw material for metallurgical application. However, other non-ferrous components are also treated for energy conservation and protecting environment. Currently, recovery in shredding and recycling plants maximises to 75% and about 25% of the feed is land-filled. However, recycling rate must be increased in due to the economical, environ-mental and social concerns. A comprehensive study for recycling, with especial focus on ferrous metal recovery, was sup-ported by Swedish Environmental Agency (MISTRA) to look at possibilities to increase the recycling rate and to reduce the amount of disposal. Part of this study was dedicated to study the shred-ding plant facilities and to look for possibilities to improve the quality and quantity of the shredding product streams. The aims were to improve the quality of ferrous scrap (apparent density > 0.9 and Cu<0.25%) for iron and steel production as well as having better quality for non-ferrous metals through the recycling schema, and finally to treat the shredder residue (SR) to recover metals and plastics to reduce the disposals. This paper summarises the results of sampling and conducting separation tests for improving the recovery of the ferrous and non-ferrous metals. The results indicated to be possible to obtain high quality ferrous scrap at recovery of 88%. However, the total recovery for metal scrap has reached 93%. Furthermore, test results on fine, P< 8mm, shredding residue (SR) showed promising prospect in recovery of metals and protecting environment by physical separation, i.e. electrical separation technique.

Jan 1, 2014

By J. D. Miller, C. L. Lin

In general, x-ray computed tomographic (CT) techniques are able to provide 3D images of the internal structure of opaque materials in a nondestructive manner. The unique cone beam geometry allows acquisition of all 2D projections with only one rotation of the sample thus providing for fast data acquisition and better x-ray utilization, as a complete 2-D detector array receives the cone-shaped flux of rays. Thus, an isotropic 3D volume can be reconstructed without the mechanical translation and the stacking of sequential slices as is the case for more conventional CT scanners. In this regard, a state-of-the-art, custom designed xray microtomography facility to provide very detailed 3D spatial analysis of multiphase particles has been installed and is in operation at the University of Utah. The reconstructed 3D tomographic volume allows for an adjustable spatial resolution from 5 to 20 microns for sample dimensions from 10 to 40 mm in diameter, respectively. Utilization of this custom designed cone-beam x-ray microtomography system is discussed. Applications described include: coal washability analysis for the design and operation of coal preparation plants, liberation analysis for evaluation of grinding practice and separation efficiency, mineral exposure analysis for prediction of the ultimate recovery from heap leaching operations, and analysis of the pore structure network of packed particle beds for simulation of flow through such porous structures as encountered in filtration and heap leaching.

Jan 1, 2003

Micro-fine disseminated molybdenite was ground in a laboratory stirred mill using steel media and zirconium media respectively. The floatability of ground molybdenite and slurry chemistry was investigated. It was found that the total recovery of ground molybdenite using zirconium media was higher while the pH and Eh of the slurry are lower than that using steel media. When steel media was used, iron oxy-hydroxides had been generated coated on the surface of molybdenite, and decreased the floatability of molybdenite, especially of the -10µm particles. The iron and lead oxy-hydroxides was generated by the reaction between steel media with pyrite and galena associated with molybdenite. It was also found that changing the grinding media to inert can benefit the flotation of molybdenite. Keywords: stirred mill, grinding environment, floatability, micro-fine disseminated molybdenite, fine grinding

Sep 1, 2012

By S. Jagdish

India ranks fourth in the world of iron ore production and exported 55% of the total iron ore production of 180.9 million tons in 2006-07. As per United Nations Framework Classification (UNFC), the total iron ore reserves in India is 25249 mt. This consists of about 14630 mt of Hematite ore and 10619 mt of Magnetite ore. While the deposits of magnetite iron ore are limited to the states of Karnataka, Andhra Pradesh and Tamil Nadu, hematite ore is available in abundance in Jharkhand, Orissa, Chhattisgarh, Karnataka and Goa. National Steel Policy, declared by government of India in 2005 envisages 110 million tons of steel production by 2020. This is likely to be revised upwards. Massive exploration work in iron ore is needed to convert the available resources of iron ore into reserve category. Steel Authority of India Limited (SAIL) produced more than 24.5 million tons of iron ore during 2006-07 and plans to produce 42.0 million tons per year by the year 2010-11 to meet the requirement for a hot metal production of 26.2 million tons. While processing iron ore, the challenge faced would be the reduction of the gangue materials ? alumina and silica. It is proposed to bring down alumina and silica in the iron ore to less than 2% each from the current level of 2.5%~3.5% each. Appropriate beneficiation schemes are being developed depending upon the mineralogical characteristics of iron ores at different mines in the country. The state-of-art beneficiation technologies like Hydro-cyclone, jigging, magnetic separation etc. will be incorporated. SAIL?s corporate plan envisages blast furnace burden of 15% iron ore lumps, 15% pellets and 70% sinter by 2010. This strategy opens up the opportunity of utilization of micro fines generated in the mining and beneficiation processes for pellet making. This also directs towards all together new technological approach to the beneficiation process. SAIL is planning to set-up three pelletisation plants of 2~3 mtpa capacity. Environmental issues like reduction in slime loss and utilization of dumped low-grade iron ore are very important. R&D Centre for Iron and Steel, SAIL has carried out extensive laboratory investigations in the above area. This will help in reducing the loss of valuable iron through slimes and also increase the iron ore resource base. Laboratory investigations indicate that low grade dumped ore fines with Fe: 55.5% can be upgraded to a product with Fe: 66.2% with about 48% recovery.

Jan 1, 2014

By Graeme Heyes, Warren J. Bruckard, Michael A. Somerville

"A limited series of laboratory batch flotation tests was conducted on a suite of calcium-ferrite-based slags made in laboratory smelting trials. The smelting tests were conducted as part of a wider CSIRO Minerals’ research project aimed at developing a single-stage continuous copper-making process. The objective of the flotation work was to maximise copper recovery and iron rejection from slags made in the process.The slags treated included a reduced low copper slag, an oxidised high copper slag composite, and a very reduced low copper self-pulverising slag. The copper content of the slags varied from 2.9% to 14% Cu. The copper was present as metallic copper, oxide copper and copper-calcium ferrite phases with the phase mix related to smelting conditions. The slags were crushed, ground, wet-screened at 355 or 210 µm to remove coarse metallic particles of copper, and floated at natural pH (about pH 11) using reagents and conditions appropriate for the selective recovery of the copper phases.In rougher/scavenger tests on the reduced low copper and self-pulverising slags copper recoveries above 92% were obtained with copper enrichment ratios varying between 2.3 and 2.9. For the oxidised high copper slag copper recoveries were poorer - only 47% of the copper was recovered with an enrichment ratio of 3.3. The presence of the slow floating copper-ferrite phases in the slags limited further (selective) copper recovery. Ageing of the high copper slag, that is, a significant delay between grinding and flotation, resulted in a deterioration of the copper flotation response.The critical parameter affecting the flotation of copper from direct converting slags was found to be the form of the copper in the slag. Slags containing a higher proportion of the more desirable form of copper for flotation will provide the best opportunity for high copper recoveries to be consistently obtained, allowing improvements in the economics of the overall copper-making process."

Jan 1, 2003

By G. Prabhulingaiah, D. M. R. Sekhar

"A phosphate deposit of estimated 6 billion tons of P2O5 is located 180 to 300 meters below the sea level, 185 kilometers north of port Luderitz, Namibia. The ore bed is 6 kilometers wide and 220 kilometers long. The ore deposit analyzing 16% P2O5 is loose sediment of 1.5 meters thick without over burden. Sizing of the ore to - 1.4 mm + 0.150 mm improves the grade to 23.54% P2O5 with a P2O5 recovery at 83.75% containing phosphate pellets and flakes of sea shells. Clay, bacterial debris as organic matter, flakes of broken sea shells and fine phosphate containing particles report to - 0.150 mm fraction and + 1.4 mm fraction contains sea shells and few phosphate containing pellets. The mineralogical composition of phosphate containing pellets is estimated (Droste, T.C., 2004) 80% frankolite, 6% pyrite, 4% illite, 3% quartz, 3% amorphous SiO2, 1% carbonates, 1% organic carbon and = 1% ilmenite, magnetite, zircon etc. The phosphate content in the pellets is around 27.7% P2O5. Trials to separate by gravity or flotation processes were not successful. Leaching of carbonates (sea shell flakes) under mild acidic condition (= 2% acetic acid or HCl solutions) or calcinations followed by leaching however yielded residues (concentrates) of grades 27.85 - 32.74% P2O5 at P2O5 recoveries ranging from 78.45 - 96.8% P2O5."

Jan 1, 2014

By E. T. Tuzcu

In this manuscript, a new approach for modeling the rate of grinding process is explained. A review about grinding rate definitions so far is given and the possible ultimate way for grinding modeling is given as modeling the rate based on energy spectra. The traditional/phenomenological approaches for modeling size distribution of grinding mills give their place to a new generation modeling technique. Developments in the computational methods and necessity to model product size distribution of large mills, larger than ball mill size, paved the way for this novel technique. The traditional grinding rate models are mostly based on the back calculated breakage parameters from the experimental data. However, direct modeling of breakage parameters and hence the prediction of size distribution of the grinding mills may become possible with this approach. The material breakage data and discrete element method (DEM) energy spectra are the main components of this approach. Albeit the focus in this study is on modeling of breakage rate under impact mode of breakage, the abrasion mode of breakage was also tested by carrying out abrasion tests. Impact mode of breakage was analyzed using ultra-fast load cell device (UFLC) and drop weight tester. Dry tumbling test was carried out for abrasion experiments. Obtained material breakage versus energy data are combined with the collision energy spectra to obtain the breakage rate function. In addition, the material breakage versus energy information from the tests is converted into breakage distribution function. The model was verified in a lab scale mill (90 cm diameter-15 cm length). 10 to 15 kg of limestone was ground using 50 mm steel ball at varying conditions, i.e., rpm, volume loading. It is shown that the proposed model predicts all (1, 2, 4 min.) grinding intervals for all experiments highly accurate.

Sep 1, 2012

By F. Karakas

Organo-bentonite production enjoys important applications including solvent based paints and, more importantly, the production of polymer/bentonite nanocomposites. Quarternary ammonium salts in this regard are still considered as the most versatile reagents in the process of hydrophobization. In this study, a purified form of Resadiye region bentonites, which is one of the most significant sodium bentonite deposits in the world, was used. The raw Na-Bentonite was typically characterized by chemical analysis, XRD and DTA analysis and more importantly for its cation exchange capacity (CEC). Other technological properties such as swelling index, pH, apparent viscosity, water absorption, oil absorption were also conducted on the raw bentonite. The mineralogical analysis of the raw bentonite reveals that it contains about 80 % montmorillonite together with other associated gangue minerals including feldspar, quartz, calcite, dolomite, coloured impurities and other clay minerals. The raw bentonite was subjected to two stage processing involving a series of hydrocylones. Different apex and vortex diameters and different pressures were employed in order to produce a bentonite concentrate with 95 meq/100g CEC from a CEC of 71 meq/100 g. This high quality concentrate was used in the production of organo-bentontonite. The modification was performed with two different quaternary amines, i.e. Trimethyl Phenyl Ammonium Chloride (TPAC) and Hexadecyl Trimethyl Ammonium Bromide (HDTMA-Br). In the modification procedure, three parameters, i.e., adsorption density, zeta potential, swelling index and apparent viscosity were studied simultaneous-ly from the same suspension to identify both the mechanism of the process and also the degree of hydrophobicity. Adsorption measurements were made as a function of conditioning period, pH, and reagent concentration. Simultaneous examination of the adsorption density, zeta potential and apparent viscosity enabled us to pinpoint the optimum region of hydrophobicity which was subsequently tested by settling and critical coagulation concentration in both water as polar and toluene as nonpolar solvents. The results are analyzed in the light of experimental data.

Jan 1, 2014

By Jianjun Tian, Changjiu Zhang, Chunmin Wang

Two lines of single stage autogenous milling circuits have been installed and commissioned as the primary grinding process for the Sino Iron project where magnetite ore is treated to produce iron concentrate via magnetic separation. Various challenges were encountered during the commissioning and ramp up stages which are discussed in the paper and include treating a highly competent ore in a closed circuit AG mill, operating the largest mills in the world and dealing with a number of engineering issues related to plant operability. Details of how these challenges were overcome are described as well as the observed operating characteristics of the mills and their optimisation through rigorous study, simulation and successful solution implementation. Further potential improvement opportunities are also discussed as part of the ongoing technical program at site.

Jan 1, 2014

By R. T. Dec

Current industrial compacting and briquetting practices are largely based on trial-and-error techniques. This paper introduces a two-dimensional finite element model of briquetting process in the roller press. Compared with other modeling techniques used in the past, finite element method offers the most versatile approach because it incorporates adequate information about powder behavior, geometry and frictional conditions and offers predictions for the density distribution, the velocity field, the stress distribution, roll force and torque. More over, when the model includes elasticity, it offers predictions on the internal stress state in the briquette after its exit from the roll. This enables to perform realistic computer experiments which are helpful for establishing the forming cavity geometry and process conditions necessary to produce briquettes with the desired properties. Three forming cavity profiles are analyzed. Results from model are verified on experimental roller press and best cavity profile is recommended for briquetting of sub bituminous coal fines.

Jan 1, 2014

By M. Brozek

The constant of flotation velocity is the value characterizing the kinetics of cyclic flotation. In the statistical theory of flotation its value is the function of probabilities of collision, adhesion and tearing off the grain from the air bubble. The grain ? air bubble collision plays a key role since there must be a prior collision before the grain ? air bubble adhesion happens. The probability of such an event to occur is proportional to the relation of the grain diameter to the bubble diameter. When the grain sizes are given, it is possible to control the value of collision probability by means of the size of air bubbles. Consequently, it is significant to find the effect of physical and physicochemical factors upon the diameter of air bubbles in the form of a mathematical dependence. In the pneumo-mechanical flotation machine the air bubbles are generated by the blades of the rotor. The dispergation rate is affected by, among others, the rotor rotational speed, the amount of air transported to the flotation chamber an time and the liquid surface tension, depending on the type and number of applied flotation reagents. In the proposed paper the authors will present the distribution of air bubble diameters on the grounds of the above factors, according to the laws of thermodynamics. The correctness of the de-rived dependences will be verified empirically.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, M. Mohammadinejad, M. Zare

"Water quality and quantity at the Tailing Thickening Section of processing plants is considered to be a crucial factor and impacts the performance of several sections. Therefore, gaining stable and effective performance at the Tailing Thickener Section is one of the principal goals of minerals processing plants. Different factors such as: qualitative and quantitative sustainability of plant feed, the balance between the mass of input and output water flow, the dissolving method and distribution of flocculant and the amount of dirt, solid percent of thickener inlet pulp, affect the performance of Tailing Thickener. The present study investigates the successful improvement of Tailing Thickener performance at Jalal Abad Hematite Iron Ore Concentrate plant through optimizing the above operational parameters. For this purpose, the following optimizations have been done: homogeneity and sustainability of plant input feed rates, fine pulp removal collected by the bag filters at the input of the thickener, adding an quietness box before moving the tail pulp into the thickener to reduce the pulp turbulence, replacing flocculant pump and injection pipes, improving water mass balance which leads to optimizing and stabilizing the concentration of input tail pulp into the thickener, adding a mixer to increase the flocculant preparation time, increasing the locations for adding flocculant to thickener from 1 point to 6 points. Applying the above modifications and monitoring the Tailing Thickener performance over the course of months, has led to the improvement of recovered water quality from 500 ppm to 200 ppm, increasing the solid underflow of the thickener from 40% to 48.5%, and similarly, reducing water loss by 60%. Of other important effects, due to improvement of water quality, grade of final concentrate 0.5% increased and because of 73% increase in monthly working hour, concentrate tonnage 55% increased. Finally, sludge thickener optimization has had a significant effect in selecting and designing the dewatering system from the underflow of the sludge thickener."

Jan 1, 2018

By F. Ngoroma

Concentrators processing PGM bearing ores make use of polysaccharide depressants to reduce the recovery of the undesired naturally floatable gangue minerals, mainly silicates, present in the ore. Recent work has shown that high depressant dosages can completely depress naturally floatable gangue and thus prevent it from reporting to the concentrate. These high depressant dosages can, however, have a negative effect on the recovery of valuable minerals present in the ore by reducing the stability of the froth. In order to counterbalance the effects of depressant addition, frothers are added. It is, however, preferable to maintain independent control over bubble size and froth stability which is difficult to achieve with only one frother. An alternative strategy is, to use a blend of frothers, e.g. a weaker frother in combination with a stronger frother. Such a system allows an additional degree of freedom: changing the ratio of the two frothers, that would provide more independent control of bubble size and froth stability. This study demonstrates, through the use of batch flotation tests, how blending low molecular weight alcohols with commercially available frothers impact the solids and water recovery, as well as the valuable mineral recovery and concentrate grade in different PGM ores. Higher water and solids recoveries together with higher valuable mineral recoveries (>90% copper and >70% nickel) were obtained from tests using frother blends.

Sep 1, 2012

By E. Scheepers

The process under investigation is the large-scale production of phosphorus. Gravity delivers the feed, consisting of pelletised apatite, coke and silica (in the form of gravel), to a submerged arc furnace through ten, evenly distributed feed chutes ensuring constant packed bed volume. Within this packed bed, solid-gas reactions are dominant in generating the gaseous product. These reactions, as well as the packed bed itself, were the main focus in the development of a fully three-dimensional CFD model in which fluid flow and energy distribution are represented as functions of chemical reactions, heating and melting of material and heat losses. The associated complex process interactions necessitated the creation of two process-specific, user-developed models that integrates accurate, thermodynamical data with computational fluid dynamics calculations, as well as reaction kinetics. The boundary conditions are provided by industrial measurements, and the key model parameters of reaction kinetics were obtained by laboratory experiments for different feed mixtures. Thirteen temperature probes installed inside the refractory lining of the furnace especially for this project allowed parameter fitting and validation to be guided within the constraints of real measurements. Simulation results reveal a thin, dome-shaped, reductive zone where conditions are optimum for maximum phosphorus recovery, as well as evidence of a thermal reserve zone similar to an ironmaking blast furnace located above this reduction zone. When compared to actual operating data, the CFD model can successfully predict the specific power consumption, the phosphorus in the slag and gaseous product flowrate under given operating conditions. This CFD model forms part of a larger project that aims to create a Dynamic-CFD hybrid control model.

Jan 1, 2014