Search Documents

By M. Y. Zhou

The paper elaborates on the significance of producing ultra-low-moisture ore concentrate, the operating principle and technical features of thermocompression- filtration process, the kinetics involved in the dewatering process, and the technological process system and equipment used. It is pointed out that it is possible to reduce the moisture of fine ore concentrate to a minimum. By way of example, the case of the treatment of flotation molybdenum (Mo) using the thermocompression- filtration process is cited.

Jan 1, 2014

By Y. S. Song

Flotation separation of galena, sphalerite with pyrrhotite in ethanoic acid + sodium acetate sys-tem was studied in this paper. The flotation tests show that galena and sphalerite can float but pyr-rhotite can hardly float in the pH range of 3.6 to 5.6 in ethanoic acid + sodium acetate system. The flotation tests also show that galena can be separated efficiently from pyrrhotite and sphalerite can be separated on the whole from pyrrhotite, but the separation efficiency of the former is much better than the latter. The flotation results have been investigated by ultraviolet spectrum and XPS analysis, and explained by theory of hard and soft acid and base (HSAB), hydrogen bond and galvanic coupling.

Jan 1, 2014

By Abhilash

Different methods of utilizing refractory bauxite and disposing red mud are practiced throughout the world, but none of them are known to be environmentally innocuous due to the complexity and /or high cost, and none has been found to be feasible on an industrial scale. Under these conditions, the use of bioleaching process seems promising. The present study emphasizes on the isolation of native extremophiles from the source Indian bauxite and red mud, with their detailed cellular and physio-chemical, and biochemical characterization. These organisms were tested for their ability to thrive in physically or geochemically extreme conditions. The gram positive capsule rich mesophiles and thermophiles were tested for removal of gangue minerals from the bauxite and red mud samples. Keywords: refractory bauxite, red mud, extremophiles, bio-beneficiation, gangue

Sep 1, 2012

By Chuanyao Sun, Zhenguo Song, Aijun Ren

"Lead-Zinc sulfide ore containing carbon is one of typical refractory resource. Because organic carbon has natural floatability, it has a great negative influence on flotation of lead-zinc sulfide ores. It is difficult to obtain qualified lead concentrate by flotation using conventional reagent system. In order to reduce the influence of organic carbon on lead and zinc flotation, two alternatives, i.e., removal carbon by pre-flotation or adding carbon depressant in lead and zinc flotation, can be adopted. If the flowsheet of removal carbon by pre-flotation is adopted, the lead and zinc recovery which are lost in the carbon tailings is often higher. If conventional carbon depressants are used in lead and zinc flotation, it has a certain depression effect on lead minerals. In the paper, the ore grading 1.49% Pb, 5.73% Zn, and organic carbon 3.14% has been carried out by flotation tests. In the bulk flotation of carbon and lead minerals, Pb concentrate is only about grading 21.00% Pb. In the pre-flotation of organic carbon, it’s hard to remove most of carbon, and the loss of Pb and Zinc recovery is too much in carbon tailings. New carbon depressant BK547 and three conventional carbon depressants including sodium lignosulphonate, Fe-Cr-lignosulfonate, and dextrin, are used in comparative tests of Pb flotation, and results show that BK547 have a good depression on organic carbon, and have almost no effect on Pb flotation. Using BK547 as carbon depressant, cycle test in flowsheet of two-stage Pb and Zn selective flotation and coarse concentrate regrinding have been carried out, and results show that concentrates grading 62.51% Pb and 41.33% Zn are obtained at recoveries of 70.24% Zn and 83.58% Zn.INTRODUCTION Lead and zinc mineral resources are still the main source of lead and zinc metal. For lead-zinc sulphide ore, lead concentrate and zinc concentrate are obtained by flotation. Minerals separation by flotation is a complex process and is dependent, along with other factors, on the relative distribution of hydrophobic (e.g. collector, polysulfide, elemental sulfide) and hydrophilic (e.g. metal hydroxide) species between different particles of the same mineral phase and between mineral phases (Piantadosi & Smart, 2002; Boulton, Fornasiero & Ralston, 2003). Organic carbon has natural floatability and is often associated with lead-zinc sulphide ores. If the content of organic carbon in the ore is more, the flotation index will become worse. The main problem is that the concentrates has too low grade to be qualified grade products for sale. At the same time, the consumption of reagents is more than ordinary ores without organic carbon. In order to solve the influence of organic carbon on the flotation of lead and zinc and other sulphide ores, a lot of research works have been carried out."

Jan 1, 2018

By Paulo Braga, Carlos Junior, Silvia França

"Lithium is the lightest of the metals, with high reactivity and great electrochemical potential. It has a low thermal expansion coefficient and high caloric value, and it forms very light and resistant aluminium alloys. These properties make lithium an attractive element for use in battery manufacture and glass and ceramics production, in addition to its applications in the aeronautic industry. Today, two sources of raw material are economically viable for lithium production: pegmatite rocks and brine. The world production, in 2012, was approximately 150,000 tons of LCE (lithium carbonate equivalent), almost triple the production in 2000. The forecasted consumption for the current year, 2013, was approximately 162,000 tons of LCE, and for 2020, it could be as much as 280,000 tons of LCE, stimulated essentially by the growth of world production of electric (EV), hybrid (HEV) and hybrid plug-in vehicles (PHEV), the batteries of which are based on Li-ions. With the growth of world demand and increasing prices, lithium minerals such as spodumene, petalite and amblygonite, once considered uneconomical for the production of lithium carbonate, are regaining their economic value. New projects to produce lithium compounds based on mineral sources are being developed in many countries, aiming to produce battery-grade lithium carbonate (99.95% Li2CO3). Although Brazil has large lithium pegmatite reserves, the domestic production of lithium carbonate and hydroxide is very low, at approximately 600 tons of LCE, which represents 0.4% of the world production. The application of these products is mostly in the grease and ceramic industries. The national lithium market is under government protection due to its potential use for nuclear purposes. Thus, the industrialization activities and import and export of ores and lithium minerals, as well as organic and inorganic products, such as metallic lithium and lithium alloys, are controlled by the National Commission for Nuclear Energy (Comissão Nacional de Energia Nuclear - CNEN). The objectives of this work to quantify the real lithium demand in the Brazilian market, considering that a large amount of lithium is indirectly imported in the form of the Li-ion batteries used in equipment such as mobile phones, cameras, tablets, notebooks and e-bikes, and to compare this demand with the current national production of LCE. Finally, some technological alternatives will be discussed, with the aim of increasing the competitiveness of the lithium industry in Brazil."

Jan 1, 2014

By H. L. Liu

With the exploitation of mineral resources, valuable minerals are more and more finer and poorer. Priority reclaiming liberation grind particle under rough grinding, will help to pervert loss of melts, raise dewatering efficiency of concentrate, reduce consumption of reagent. And it is propitious to reduce energy consumption and raise the utilization rate of resources. With the feature of coarse particle?s desorption and deposition, CLF flotation machine has special pulp circulating way, which is not only apply to treat coarse particle but also normal size particle. The paper advanced the history, the design principle, the structure feature and the application of CLF flotation machine.

Jan 1, 2014

By E. Yigit

In the flotation process the physical factors such as agitation intensity air flow rate and pulp solid concentration are very important parameters affecting grades and recoveries of the products. The flotation tests were performed on the samples of Bigadic colemanite ore to investigate these factors at different agitation intensities ranging from 1000 rpm to 1400 rpm and air flow rates from 1000 cm3 ? min-1 to 2000 cm3 ? min-1 with 2 L and 4 L cells using Denver laboratory flotation machine. The tested collectors were Cytec Aero 825, Aero 848N and their mixtures. Agitation intensity and air flow rises resulted in more floated material although sometimes being not selective. These effects can be attributed to powerful collisions between air bubbles and mineral particles. The first observation was the effect of pulp solid concentration on the floatability of minerals, while the flotation in 2 L cell (0.125 g.L-1 solid concentration) at 1000 rpm (0.176 wattcm-3), and with 1000 cm3.min-1 air flow rate was possible, the flotation in 4 L cell (0.0625 g.L-1 solid concentration at 1000 rpm. (0.176 wattcm-3) and with 1000 cm3 ? min-1 air flow rate was not possible. However at 4 L cell after increasing agitation intensity to 1200 rpm (0.201 wattcm-3) keeping 1000 cm3 ? min-1 air flow rate, flotation was possible again. This shows that these factors such as agitation intensity have some critical role on flotation. Another interesting observation was on the selective effect of pulp solid concentration. In the flotation with 1 L cell at different agitation intensities, collector Aero 848N was selective against calcite, while in the flotation with 2 L cell at different agitation intensities the same collector Aero 848N was selective against colemanite.

Jan 1, 2014

Hydrofluoric acid (HF) is traditionally used in plant operation to separate feldspars from quartz. It acts during the conditioning step as a pH regulator and an activating agent providing an excellent selectivity. However, a corrosive chemical environment and the ecological impacts from the potential fluoride ion contamination are limiting factors to use this chemical agent at an industrial scale. Investigations of the amine-feldspar interactions in the absence and presence of non-linear long-chain alcohols were carried out on two ore samples. The presence of alcohol molecules led to form a closed packed layer only on the surface of feldspars. The highest order and packing at the feldspar surface were observed with a particular alkyl chain structure as Guerbert alcohols. A new flotation process was developed and tested at both lab and pilot scales on different feldspar ores. The Guerbert alcohols allow to perform a feldspar concentrate with very low content in quartz (2.3-3.5 %) and feldspars recovery from 78 to 81 % while the aliphatic isoalcohols show a more higher recovery level (88-89 %). New HF-free process is strongly dependent on the pH range (1.7-2.5) and sulphuric acid consumption during conditioning steps. Optimal amine/alcohol weight ratio is ranged between 0.8 and 1.0. The values below 0.8 decrease strongly the flotation selectivity and the quartz recovery within the feldspar concentrates is higher than that occurs with HF.

Sep 1, 2012

By W. Y. Gao

Diaojuntai Concentrator adopts a process of low intensity and high intensity magnetic separation and anionic reverse flotation, with all the concentrate from magnetic separation being treated by re-verse flotation to obtain a qualified final concentrate. The high reagent cost and energy consumption of the reverse flotation have led to a high concentrate cost. The test research on reducing the feed to the reverse flotation was therefore carried out. Based on the study of the properties of the ore sample, the concentrate of low intensity magnetic separation was screened at 0.076 mm and the undersize fraction was concentrated by concentrator with gravity and magnetic field. The results show that a qualified concentrate can be obtained at various rising current rate, pulsating current and power-on style, with the operation rate over 85%. The extraction of some part of qualified concentrate from the concentrate of low intensity magnetic separation by magnetic separation can reduce the feed to the reverse flotation by about 35% so as to reduce the production cost of concentrate.

Jan 1, 2014

By Jingzhong Kuang, Zheyu Huang, Chuanzhou Guo, Pengfei Liu

"In this paper, scheelite and scheelite coated with Pb2+ (SC) were synthesized by chemical precipitation with the help of ultrasonic. The role of the Pb2+ on scheelite was evaluated. Additionally, the dissolution behavior of minerals and the adsorption mechanism of collectors were investigated systematically via SEM, XRD, EDS. The results indicate that the ultrasonic cavitation can promote the formation of scheelite with large particle size and high crystallinity. Due to the exchange of WO4 2- and OH-, the dissolution of scheelite are not in a 1:1 equivalent amount by chemical formula and the concentration of WO4 2- is higher than that of Ca2+ in the solution because Pb2+ promotes the transfer of WO4 2- from scheelite surface into the solution. The dissolution of scheelite is an endothermic reaction and its enthalpy reaches the maximum value of 692.59J·mol-1 at pH=8~10. But the coating of Pb2+ changes the thermal effect of scheelite in the solution and the dissolution of SC is an exothermic reaction with the dissolution enthalpy of -262.30 J·mol-1. At pH=8~10, the adsorption capacity of sodium oleate and salicylhydroxamic acid on the surface of SC is higher than that of scheelite which delivers that Pb2+ contributes to the scheelite surface dissolution and enhances the adsorption of collectors on the mineral surface, thus achieving activation.INTRODUCTIONIn modern society, tungsten is a type of quite important rare metal and also a strategic resource. Because of its low vapor pressure, high melting point, good electrical and thermal conductivity properties, it is widely applied in high-temperature technology, lighting, machine and engine construction (Zhao,Z.W, 2013; Yan, W, 2017; Ilhan, S, 2013). Both scheelite and wolframite are the major tungsten deposits. With the depletion of easily-processed wolframite, scheelite has drawn a great deal of scientific and industrial attention. Scheelite can be recovered by flotation due to the metathesis of polarity and chargeability on minerals surface via adding regulators and collectors."

Jan 1, 2018

By S. Patra, R. Venugopal

"The quality of pellets produced is affected by quality anssastd quantity of green pellets, amount of addition of binders, type of binders added, amount of moisture added along with the other variables like rotation, inclination and fineness of feed. The green pellet quality depends upon chemistry, mineralogy and granulometry of fines used for pellet making, the feed size, its moisture content and porosity. During firing of green pellets ingredients present within reacts to form different phases and microstructure. So in turn physical and metallurgical properties of pellets are influenced by amount and type of binder and flux addition, induration time and temperature. During iron making process, the metallurgical properties of fired pellets are decided by the type and amount of these phases and their chemistry. Green pelletizing and induration studies have been already carried out with hematite ore fines. Indian iron ores of high alumina content showing different pelletizing characters, these studies can’t be directly interpreted. The main objective of proposed research work is to understand the green pelletizing process and determine the water bentonite interaction at different levels. Detailed investigation on swelling behavior of bentonite and microstructure of the green pellets of iron ore fines from SAIL captive iron ore fines from the Barsua in the state of Odisha. To convert these ore fines into pellets, the key raw material, additives and process variables that influence the pellet quality needs to be identified.INTRODUCTION Pelletization is the unit operation of agglomerating iron bearing fines (generally below 150µ with 65-80% passing 40µ) by tumbling in horizontal rotating drums or inclined discs, (Sivrikaya and Arol, 2013; Bhuiyan et al., 2011; Forsmo et al., 2006; Sastry et al., 2003) and the pellets are approximately spherical lumps formed by this process in presence of water and binder, on subsequent induration at 1300°c (Sivrikaya and Arol, 2014; Sivrikaya and Arol, 2013; Sivrikaya and Arol, 2012; Sivrikaya and Arol, 2010; Sastry et al., 2003; Kawatra and Ripke, 2003; Iveson, 2001a; Iveson, 2001b)."

Jan 1, 2018

By B. Orberger, J. M. Milazzo, S. B. Blancher, J. Lützenkirchen, J. L. Dubos

"Industrial dusts are commonly agglomerated using empirical recipes with binders such as bentonite, while Sludges are agglomerated into mixes. Those materials contaminate the products, are expensive and generate significant amounts of slag. Achieving cold dust agglomeration with little or no binder requires understanding the controlling parameters in order to predict and optimize the process behavior. This in turn necessitates comprehensive dust characterization to base predictions on measurable characteristics. In the present work we collected 13 Mn-rich dusts over all the process chain: feed fines, smelting, and refining dusts, as well as ferromanganese alloy dust. This is the first systematic study of dusts along the Mn-processing chain for chemical, physical and mineralogical parameters. X-Ray Diffraction, Qemscan® and laser granulometry analyses show that the mineralogy, Particle Size Distribution (PSD) and morphology evolves from complex heterogenous to simple, homogenous along the process chain: The mineralogy of the primary ore dusts shows various hydroxides, oxides, carbonates, tectosilicates and phyllosilicates. The furnace dusts contain oxides, tectosilicates and carbonates with volatiles, while the refining dusts present only oxides and metal. Finally, the Metal dust is nearly pure metal. Particle morphologies and PSD vary from jagged, irregular particles with broad PSD (>1 mm to <0.3 µm) to smooth and spherical with narrow PSD (100 µm to <0.3 µm). The Metal dust is an exception with angular particles. The Cationic Exchange Capacities (CECs) of all samples range from 0 to 22 meq/100g. Specific surface areas (SSAs) range from <0.1 to 27m²/g, and seem to decrease with from ore feed to Metal dust. This may be due to the disappearance of hydrated and/or sheet-bearing minerals, since a smaller grain size usually implies an increased SSA. The zeta potential varies strongly over the range of the samples tested. However, beside the Gabon ore which has an Isoelectric Point (IEP) ~ 4.1, the other IEP ranges between 2 and 2.5."

Jan 1, 2018

By Arkady Senchenko, Yevgeny Zhagun, Yury Kulikov, John Starkey

"The paper contains description of a new project in Russia - gold-processing plant at Aleksandrovskoye deposit (start up in September, 2013). The paper includes a brief description of plant flowsheet, data for material composition and technological properties of ore, as well as information about the achieved parameters of ore processing over the first months of plant operation. The project is interesting because a new semiautogenous mill and a ball mill were purchased on the basis of SAGDesign Consulting Group recommendations after the testing of ore samples characterizing the deposit according to specific years of operation. The plant has relatively small design capacity - 750 000 tpa, but nevertheless is the biggest gold-processing plant in the territory of Zabaikalsky region. Major valuable component in the ore is gold, silver is recovered as a by-product. The ores are very hard to grind. The design grinding flowsheet includes a semiautogenous mill operating in closed circuit with a screen, and a ball mill operating in a closed circuit with hydrocyclones (SAB). Process technology includes gravity processing and flotation with subsequent cyanide leaching of concentrates. Mill operation analysis and conclusions about the compliance of the achieved values to target ones are shown, as well as the accuracy of SAGDesign method when applied to very hard ores of Aleksandrovkoye deposit are presented in this paper. Basic directions of technological flowsheet optimization are also given."

Jan 1, 2014

By J. T. Liu

Packing in a flotation column is one way to increase separation efficiency and effective descending flotation-column height. In this paper, the difference between filling packing and sieve packing is described, and the flaws of filling packing in flotation columns in industrial application are pointed out. A change of flotation process and its effect on flotation results are reported. Based on sieve-plate filling, a high-efficiency mixed packing mode consisting of screen-plate packing and honeycomb-tube packing has been proposed, with the packing mode optimized in the cyclonic static microbubble flotation column in the separation zone. In the mixed packing mode, the honeycomb tubes are used to reduce the vortex effect at the base of the column and weaken the radial dispersion of jetting bubbles, and the sieve plates are used to comminute bubbles in the separation zone, to lengthen the bubble migration path, and to stabilize the foam layer. The superiority of honeycomb-tube packing is analyzed using bubble-particle collision theory, and the dynamic equations of collision probability are derived. The role of mixed packing in guaranteeing mineral recovery is analyzed by the axial dispersion method, and a dimensionless axial dispersion model is derived. When a high-turbulence flow is maintained, a static separation environment is formed in which secondary mineral processing is rendered more effective. In this way, a nonlinear separation environment is formed in the flotation column. Finally, mixed packing was applied in an industrial test. A large vortex developed at the base of the column. It was observed that the bubbles in the radial flow were homogeneously dispersed, the residence time of the pulp was prolonged, and the froth layer became thick and stable. Based on the test data, it was found that the sieve packing has the potential to yield a product of approximately 25.83% copper concentration with 91.78% recovery from a feed concentration of approximately 0.727%. If mixed packing were used, the product concentration could be further increased to 27.60% from a feed of approximately 0.739% concentration with 93.38% recovery.

Jan 1, 2014

By M. X. Jia

This paper discusses two mineralogy characteristics that may affect the flotation of sulfide ore. The first one, process mineralogy study on a Cu-Ni sulfide ore shows that valleriite and tochilinite are incline to form on chalcopyrite, pyrrhotite and serpentine surface, and the further guess is that the formation of valleriite and tochilinite may also causes the serpentine transform to talc, so the serpentine surface is a phase of talc or a transition phase from serpentine to talc and this enhances the flotability of the gangue minerals. The second discussion on the flotation behavior of the sulfide minerals from the point of view of the mineral semiconductor character.

Jan 1, 2014

By Mingfei He, Xianyang Qiu, Hongling Wang, Yude Gao, Qingbo Meng, Xiaoping Xu, Hao Bu, Guosheng Wang

"By the “HGMS-gravity separation-Flotation” combined technology, a Ta-Nb-Sn concentrates with the grades of Ta2O5 10.00%, Nb2O5 9.13% and Sn 42.62% at the recovery of 44.73% , 9.13% and 14.62% respectively , a Li concentrate with Li2O 3.11% at the recovery of 51.83% and a feldspar product are obtained. All the value elements are recovered. INTRODUCTION Tantalum and niobium widely used in electronics, atomic energy, aerospace and chemical industries with the advantages of high melting point, good ductility, low vapor pressure, strong corrosion resistance and high thermal conductivity are important strategic resources which occupy a special position in rare metals (Crockettand, 1993; GAO and Zou, 2004; LI and HUANG, 2012). China's tantalum and niobium resources are poor, and most of them are low grade, fine grain size, complex composition, and polymetallic associated with refractory mineral resources (GAO and Qiu,2013; Liang and Li, 2016). The Yifeng Lion Ore containing lithium and other rare metals (tantalum, niobium and tin) is an important lithium polymetallic deposit in China Jangxi province. While extensive previous studies have settled on the recovery of lithium minerals by flotation only for the extremely low grade of Ta, Nb and Sn. The regular gravity concentration is used, and the recovery of tantalum niobium is low. This paper sets out to investigate a combined flowsheet of “high gradient magnetic separation (HGMS),-gravity separation-flotation” to effectively comprehensively recover the Li, Ta, Nb, Sn and the feldspar resources in the Yifeng Lion Ore.ORE PROPERTIES Chemical analysis The run of mine comes from Jiangxi Yifeng Lion ore. The main elements of the ore chemical analysis results shows in Table 1. From Table 1, the grades of lithium and rubidium are relatively high, but the grades of tantalum and niobium are lower than the industrial grade; feldspar with high content of potassium and sodium and low content of iron can be used as high-quality ceramic raw materials."

Jan 1, 2018

By Z. Naziemiec

Since several years in Poland a huge demands on mineral aggregates occur, for the reason of intensive development of housing and road industry, as well as industrial building. Limitations in re-sources of broken aggregates in Central and Northern parts of Poland cause, that both the non-waste production of aggregates with high quality and the production of alternative aggregates from recycling gain greater importance, nowadays. It entails increase in demands for crushing devices, which are easy and reliable in operating as well as inexpensive and enabling to obtain a good quality products. Jaw crusher, regarded as the most spread in Polish industry, meet these requirements, however, their crucial disadvantage is a large content of irregular grains in crushing products. Numerous investigations show, that the shape of grains is a significant feature of aggregates, which influences on durability and quality of produced concretes. The advantage of jaw crushers is their easy operation, low price as well as low amount of dusts (wastes) generated in comminution products in comparison to other types of crushers (i.e. hammer crushers).

Jan 1, 2014

By M. Unesi, S. Haj Mohammadi, M. R. Abdoli, M. R. Garmsiri

"Hydrocyclone-thickener circuit is a promising solution to enhance the dewatering efficiency in mineral industries. The challenges in the circuit is reducing particle size in the thickener feed and the good feature is a rise in the retention time of sediments in the thickener. In this work, the effect of particle size, bed depth and residence time on the thickener performance were investigated. In this order, pilot scale columns were employed at Sarcheshmeh and Shahrebabak copper complexes. Furthermore, the influence of residence time was differentiated due to the variations in the bed depth and settling flux. Moreover, a new approach was introduced to estimate solids residence time in the thickener. results indicated that with smaller particles that are introduced to the column, the bed density as well as thickener discharge solids concentration dropped significantly. It was found that thickener discharge solids concentration fell from 59.6 to 33.8 % with reducing particle size from 130 to 22 µm in the settling flux of 20 t/m2/day. Additionally, it was found that longer residence time and deeper bed resulted in an increase in the thickener performance while the bed depth has a stronger effect. It was proved that employing a hydrocyclone prior to the thickener resuted in an increase in the dewatering efficiency.INTRODUCTION Thickeners are widely employed in mineral industries to recycle tailings and concentrate water content. A limited fraction of suspension water content is recycled using a thickener. For instance, about 50 percent of tailings water content could be recycled using a shallow bed thickener during copper processing. Since the scarcity of global water resources became more serious, the demand for improving dewatering efficiency in mineral industries became more significant [1]. A number of solutions were recommended to enhance dewatering efficiency of thickeners including optimization of current thickeners, employing deep bed thickeners and utilizing thickener-filter or hydrocyclone-thickener circuits. Optimization of existing thickeners is essential, however, it does not meet the significant demand for recycled water. The application of deep bed thickeners (known as paste thickeners) has been rising in the mineral industries [2] due to a higher dewatering efficiency while its costs is remarkable."

Jan 1, 2018

By Kevin Galvin, James Dickinson

"The Reflux Flotation Cell (RFC) consists of an inverted fluidized bubbly bed, located above a system of parallel inclined channels. This novel arrangement enhances the hydrodynamics of flotation in a number of ways. Firstly, the free-surface of the flotation cell is enclosed via a fluidized bed distributor, ensuring uniform application of wash water to promote desliming. Secondly, foams can be variable in their stability and lack permeability. Hence this system is preferably operated in the absence of foam, instead opting for a bubbly zone of high bubble volume fraction through the use of a very high gas flux and/or wash water flux. Discharge of the product proceeds upwards through a central port of narrow cross-sectional area. Thirdly, the system of inclined channels increases the segregation between the bubbles and the water, ensuring the bubbly zone remains contained within the upper vertical zone, and the liquid flux reporting to the overflow is low. The expanded operating regime of the RFC was investigated by covering a very broad range of gas fluxes, up to 5.5 cm/s, and wash water fluxes, over 2 cm/s. Both laboratory and pilot plant performances were quantified by the recovery of hydrophobic particles and rejection of the hydrophilic particles, using model and industrial coal feeds. The new system hydrodynamics was found to offer significant advantages in flotation kinetics, desliming, and particle recovery across a broad particle size range. Bubble interfacial flux reached as high as 600 m2/m-2s-1. The upper system consists entirely of a high volume fraction of bubbles, which provides a "safety-net" to protect against the detachment of coarse particles, and a highly permeable zone for counter-current washing of the flotation product. Under relatively extreme conditions selective stripping of the product is observed, resulting in grade recovery values beyond those achievable using the tree flotation method."

Jan 1, 2014

By Y. S. Li

The life cycle assessment method is applied to investigate the environmental impacts of cop-per-slag and copper-ore concentration process. Some environmental load data of copper production are obtained. The result indicates that damage level of human health, ecosystem quality and re-sources respectively is 0.174, 0.0203, 0.246 in the copper-slag concentration and 0.112, 0.0136, 0.299 in the copper-ore concentration. Environmental impact of copper-slag production (0.44) is more than that of copper-ore production (0.42), but can meet the environmental protect demand. With domestic copper concentrate supply gap enlarging, recovering copper from slag will lead to a significant improving of resource utilization and development of circulation economics.

Jan 1, 2014