Search Documents

By Natalia Konstantinova, Kira Mizell, James R. Hein, Georgy Cherkashov, Amy Gartman, Pavel Mikhailik

INTRODUCTION Ferromanganese (FeMn) crusts from Mendeleev Ridge, Chukchi Borderland, and Alpha Ridge, in the Amerasia Basin, Arctic Ocean, are similar based on morphology and chemical composition. The crusts are characterized by two- to four-layered stratigraphy. The chemical composition of the Arctic crusts differs significantly from hydrogenetic crusts from the North Pacific Prime Zone (PCZ; Hein et al., 2013), such as a high mean Fe/Mn ratio (2.6 versus 1.3) and low Si/Al ratio (1.8 versus 4.0), with lower Mn, Ca, Ti, P, Ba, Co, Cu, Ni, Pb, Sr, and Zn and higher Si, Al, Mg, As, Li, V, Sc, and Th. Based on Arctic FeMn crust mineralogy, chemical composition, and growth rates, crust formation was dominated by three processes: Precipitation of Fe-Mn (oxyhydr)oxides from ambient ocean water, sorption of metals by the Fe and Mn phases, and fluctuating but large inputs of terrigenous debris (Konstantinova et al., 2017; Hein et al., 2017). The Mn and Fe phases are hydrogenous and reflect bottom ocean-water chemistry and the aluminosilicate phase contains stable detrital minerals such as quartz, feldspars, zircon, monazite, and clay minerals. A precise method of studying the distribution of elements in FeMn crust phases is sequential leaching that dissolves four mineral phases of different stability step-by-step, in the following order: easily leachable phase, mostly bio-calcite; manganese oxides; iron oxyhydroxides; and residual aluminosilicate minerals (Koschinsky and Halbach, 1995). Twelve bulk crusts and crust layer samples obtained from six hydrogenous FeMn crusts were studied. Those crusts were collected during Russian (Arktika 2012) and USA (HLY0805, HLY0905, and HLY1202) research cruises from different parts of the Amerasia Basin (Mendeleev and Alpha Ridges, Chukchi Borderland). Samples were chosen for the sequential leaching experiments based on their morphology, location, and water depth. Hydrogenetic crust (D07-33) from the Tuvalu EEZ, central-west Pacific Ocean, was included in the experiment for comparison. Recovery during the four-step sequential leaching, with respect to the bulk analyses, was between 80% and 120%.

Jan 1, 2018

By Stephen J. Juras

The Myra Falls deposits comprise a complexly metal-zoned polymetallic volcanogenic massive sulfide district located 90 km from Campbell River in central Vancouver Island, British Columbia, Canada. The massive sulfide deposits are hosted by subaqueously-deposited rocks of the Devonian age Myra Formation of the Sicker Group volcanic assemblage. The deposits comprise many individual massive sulfide lenses grouped into several major zones within two main felsic volcanic stratigraphic intervals - the upper Lynx-Myra-Price Horizon and the lower H-W Horizon. The largest of these zones, the H-W and Battle, occur within the H-W Horizon. The first claims in the area of what is now Boliden-Westmin?s Myra Falls Operations were staked in 1917. Early prospecting resulted in the discovery of three massive sulfide showings which eventually became the Lynx, Myra and Price mines. Sporadic exploration was carried out until 1961 when Western Mines Ltd. (now Boliden-Westmin Ltd.) acquired the claims. Subsequent ore definition outlined 1.9 million tonnes of ore (approximately 5 years of mine life) in the Lynx deposit, and mining began in 1966. Pre-mining geological reserves (to January 1, 1997) comprised 6.7 million tonnes grading 3.3 g/t Au, 130.6 g/t Ag, 2.0 % Cu, 1.4 % Pb and 10.2 % Zn for the Lynx-Myra-Price deposits, 17.1 million tonnes grading 2.3 g/t Au, 32.7 g/t Ag, 2.3 % Cu, 0.3 % Pb and 4.2 % Zn for the H-W deposits and 4.2 million tonnes grading 1.1 g/t Au, 27.0 g/t Ag, 2.2 % Cu, 0.5 % Pb and 12.0 % Zn for the Battle deposits. Property-wide production to January, 1996 has been 15.7 million tonnes grading 2.1 g/t Au, 58.7 g/t Ag, 1.9 % Cu, and 5.2 % Zn.

Jan 1, 1998

By Sang Joon Pak

Deep-sea mineral resources explored by Korea are categorized into mainly three types; manganese nodules, manganese crusts and seafloor massive sulfides. Manganese nodules have high Pt enrichment factors (EF=400, ore/crust ratios). Rare earth oxides (REO) contents from manganese nodules show from 0.037 to 0.302 REO% with mean value of 0.12%. Te and Pt are highly enriched in manganese crusts, displaying EFs of 10800 and 150, respectively. REO contents of manganese crusts are slightly richer than manganese nodules (0.013~0.387 REO%, average = 0.18 REO%). Seafloor massive sulfides deposits are featured by outstanding values of Se (EF=1300) well as In (EF=110). Au (0.8~26.3 g/t) and Ag (0.9~348.0 g/t) are another enrichment metals in SMS, although they belong to precious metals. Rare earth elements of SMS are meaningless as resources but REE are increasing in sediments overlying SMS. Heavy rare earth elements (HREE) from both manganese nodules and manganese crusts are typically higher than ones from land-based REE deposits. HREO grade and their portions of manganese nodules as well as manganese crusts are greatly similar to ion-absorbed type REE deposits in China, implying REE of subsea mineral resources are absorbed in nodules and crusts. Rare metals including REE could be exploited as by-production of commodities such like Ni, Co, Cu and so on. Rare metal resources from manganese nodules and manganese crusts are featured by low-grade and large scale deposits. Therefore rare metals in subsea mineral resources will add its economic values.

Jan 1, 2011

By V. V. Ivanov, A. I. Khanchuk, E. V. Mikhailik, M. G. Blokhin, P. E. Mikhailik

At present, marine ferromanganese crusts of seamounts are of great interest as a source of high-tech metals. The metals most enriched in these deposits are essential for a wide variety of green-tech, emerging-tech, and energy applications (Hein et al., 2013). There is a grate number data on the content of major and minor metals (thousands analyses). However, information on the content of such elements as platinum, gold and silver in the world literature is limited. The concentrations (N – number of analyses) of platinum, gold and silver in the Pacific are 418 ppb (N = 105), 35 ppb (N = 72), 1.02 ppm (N = 26), respectively, and in the North Pacific Prime Zone - 477 ppb (N = 66), 55 ppb (N = 13), 0.1 ppm (N = 4); in the Atlantic Ocean is 567 ppb (N = 2), 6 ppb (N = 2), 0.20 ppm (N = 18), in the Indian Ocean, 211 ppb (N = 6), 21 ppb (N = 2), 0.37 ppm (N = 9) respectively; (Hein et al., 2013). The northern part of the Pacific is poorly studied in this question. The samples of ferromanganese deposits (FMD) was recovered from the Govorov Guyot (Magellan seamounts), MZh-33 Guyot (Marshall Islands), as well as the Detroit Guyot (Imperor Ridge) and Yomei Guyot (Fe-Mn placer Holes 431 and 431A DSDP, Imperor Ridge).

Jan 1, 2018

By Grigori Abramov

Borehole Mining (BHM) is a remotely operated underground and underwater method of extracting (mining) mineral resources by high-pressure water jets. It can be carried-out from the land surface, open pit floor, underground mine and floating platform or vessel. The method is currently in use in mining and exploration of such natural resources and industrial materials as: uranium, iron ore, quartz sand, gravel, coal, poly-metallic ores, phosphate, gold, diamonds, rare earths, amber and several more. Yet another application of Borehole mining technology is construction of subsurface collectors, ground walls and storage for compressed or liquefied gases, oil and other products.

By Jiahua Pan, Yanxiong Mei, Shuqin Liu, Rongfu Pei

Growth characteristics of Co-rich crusts from the Western Pacific have been approached. The thick crust shows 3 structural layers: compact upper layer, porous middle layer, and compact lower layer. The middle and lower layers have obviously different microscopic structure, color, and luster. Preliminary study of Calcareous nanofossils in one crust shows that the crust began to grow since Paleogene. The porous middle layer was formed from late Miocene to late Pliocene (Ca. 0.5 ~ 11.9Ma) and the compact lower layer was formed from late Paleocene to late Oligocene (Ca. 56.3 ~ 23.2Ma). The sedimentary hiatus of a 14.26Ma was observed between the middle and lower layers. The boundary between them to be Oligocene/Miocene (O/M) shows an important message on growth age.

By Fernando JAS Barriga

The world-class Neves-Corvo deposits were intersected by drilling in 1977. They occur in the (Carboniferous) Iberian Pyrite Belt (IPB), Western Europe&apos;s largest stock of base metals (see Bamga, 1990, in Dallmeyer RD, & Martinez E, eds, Pre-Mesozoic Geology of Iberia, Springer-Verlag). Massive and stringer sulfides in the area sum up to about 200 Mt (109 kg), in five main orebodies (Neves, Corvo, Graca, Zambujal and Lombador). They include unique, extremely high grade copper and tin ores ( - 33 Mt Cu ores, -7.5% Cu, and -4 Mt Sn ores, -2.6% Sn, - 12.5% Cu). Also present are -50 Mt polimetallic ores (-6% Zn, 1.2% Pb, 64 ppm Ag). The remaining are relatively low grade pyritic massive and stringer sulfides (Cu < 2%. Sn < 1%, Zn equivalent < 4%). The geological setting is one of bymodal submarine volcanism, with predominant felsic, explosive volcanism and associated sedimentation (detrital and chemical), which took place on a shelf-facies, quartzite-phyllite basement (of Upper Devonian age). The plate tectonic setting has been the object of much debate. Current interpretations favour that the IPB volcanism took place in a tensional fore-arc region, associated with oblique subduction and collision (Silva et al., 1990, same volume as above). At Neves-Corvo there are many different ores, that may be grouped in four main types: fissural (at the base), breccia, massive (intermediate) and "ruban6 " (at the top). Fissural ores seem to correspond to stockworks in contrasting types of host rocks (gray to black shale, sericitic, chloritic and graphitic, and light gray volcanic rock). Massive ore may contain significant shaly gangue, at the base of individual orebodies, and silica-rich (cherty) varieties towards the top. The more sulfide-rich varieties predominate, and are usually well banded.

Jan 1, 1993

By Raymond A. Binns

The Eastern Manus Basin (EMB) contains three major active hydrothermal zones and a number of smaller occurrences of hydrothermal deposits, and can be considered as a regional-scale modern analogue for volcanic-hosted mineral fields on land. Unlike the central Manus Basin, a back-arc spreading zone with some MORB-like basalt-hosted massive sulfide deposits, the EMB is a pull-apart rift zone between two transform faults, where a basement of Eocene-Oligocene arc crust is being thinned by extension, with rapid sedimentation on the tilted fault blocks. Present-day submarine igneous activity in the EMB, with which hydrothermal activity is associated, has arc geochemical affinities and is related to subduction of the Solomon Sea Plate at the New Britain Trench. Overall, hydrothermal deposits in EMB are found with lavas ranging from picritic basalt to rhyodacite in composition, although the two major occurrences of massive sulfide are hosted by the more siliceous dacite and rhyodacite variants. Some volcanic edifices are central eruptions, mostly of porphyritic lavas or domes, while others are elongate ridges formed by fissure eruption in which the typically aphyric lavas were very fluid. Evidence for shallow-level fractional crystallisation controls of lava chemistry implies presence of subjacent differentiated intrusions or former magma chambers. Seismic tremor at one site during the nearby 1994 Rabaul eruption suggests magma movement in the chamber.

Jan 1, 1998

By Jelena Milinovic, Sofia Martins, Anna Lichtschlag, Sven Petersen, Fernando J. A. S. Barriga, Bramley Murton, Adeline Dutrieux

"The active TAG hydrothermal mound is one of the largest and better studied. Due to its size (one of the largest, known so far, in the Atlantic Ocean) and concentration of specific economic valuable elements, it might be considered for future exploitation due the increasing demand for raw materials. However, the discovery of several large inactive sulfide mounds, some partially buried under sediments may relieve this pressure. Exploration for such occurrences can, together with geophysical exploration tools, be accomplished by mineralogical and geochemical studies of those sediments.INTRODUCTION AND GEOLOGICAL SETTINGThis study reports the results from sediment samples collected during the Meteor M127 cruise on the TAG hydrothermal area in 2016. The Trans-Atlantic Geotraverse (TAG) hydrothermal field (Mid-Atlantic Ridge, 26°08’N) is located 2.4 km east of the main rift valley at depths of about 3650 m. The TAG hydrothermal field stands as an example of a massive sulfide deposit on a low-spreading ridge associated with an active detachment fault (Humphris et al., 2015).Associated with the TAG hydrothermal field are metalliferous sediments/deposits that can reach several meters in thickness (Metz et al., 1988). These sediments/deposits can be formed by hydrothermal plume fall out (buoyant and nonbuoyant), massive wasting of hydrothermal edifices (sulfide mounds and chimneys) and authigenic mineralization (Gurvich, 2006). By studying the grain size, mineralogy and geochemistry of the sediments it is possible to identify each type of sediments and find their proximal or distal distribution. The location of the gravity cores studied here is distributed along sediment ponds near inactive hydrothermal mounds [Three mounds area (B)], actively venting low-temperature mound [Shimmering mound (A) and Mir zone (D)] and an area of sediment accumulation [Central area (C)] (Rona et al., 1993) (see Figure 1)."

Jan 1, 2017

By Michael J. Cruickshank

A workshop to examine recovery systems for selected strategic and critical materials in the U.S. National Seabeds for the National Defense Stockpile in the 21st Century was held in Hawaii September 26-28, 1991, sponsored by the National Science Foundation and the Marine Mineral s Technology Center. The National Defense Stockpile of critical and strategic mineral commodities is presently in a deficit position of more than 7.5 billion dollars. Current domestic reserves of some commodities are limited or nonexistent. As defined by the U.S. Bureau of Mines, "Reserves are select resources . . . which at the time of classification, can be mined at a profit." Occurrences of these minerals have been discovered offshore within U.S. jurisdiction. If the technology could be developed to convert these resources into usable ore reserves, our dependence on foreign ores could be greatly reduced. Preliminary estimates indicate that a ten-year program of ore reserves definition, with appropriate technical developments to demonstrate a recovery system, could cost less than half the amount authorized for stockpile acquisition in FY 1989 alone.

Jan 1, 1991

By Masaomi Kurihara, Seiya Kawano, Norihiro Yamaji, Satoshi Shiokawa, Nobuyuki Okamoto, Hironobu Sakurai

Seafloor polymetallic sulphides are distributed in the EEZ of Japan, including substantial deposits in the Okinawa Trough and Izu-Bonin back-arc basin. In this new frontier, the successful development of these resources in Japan is expected to bring about a new domestic supply of mineral resources. The initial stages of this development are authorized by the Basic Plan on Ocean Policy, approved by the Japanese Cabinet on April 26, 2013, and the Plan for the Development of Marine Energy and Mineral Resources, formulated by the Ministry of Economy, Trade and Industry (METI) on December 24, 2013. In 2008, the Japan Oil, Gas and Metals National Corporation (JOGMEC), commissioned by METI, began a survey and technological development programme for the development of the seafloor polymetallc sulphides (PMS) based on these Plans. The examination of four different fields: the evaluation of the amount of the resource, environmental assessment, mining technology, and processing & smelting technology, are concurrently promoted, aiming for commercialization as soon as possible. Based on the results of research for properties of geomorphology and marine environments of the target test sites in the Okinawa trough, which have been ongoing for several years, the preparation of the pilot lifting test included an in-situ excavation and crushing test conducted using test excavating and crushing systems.

Jan 1, 2018

By Masaomi Kurihara, Seiya Kawano, Norihiro Yamajim, Satoshi Shiokawa, Nobuyuki Okamoto, Hironobu Sakurai

Seafloor polymetallic sulphides are distributed in the EEZ of Japan, including substantial deposits in the Okinawa Trough and Izu-Bonin back-arc basin. In this new frontier, the successful development of these resources in Japan is expected to bring about a new domestic supply of mineral resources. The initial stages of this development are authorized by the Basic Plan on Ocean Policy, approved by the Japanese Cabinet on April 26, 2013, and the Plan for the Development of Marine Energy and Mineral Resources, formulated by the Ministry of Economy, Trade and Industry (METI) on December 24, 2013. In 2008, the Japan Oil, Gas and Metals National Corporation (JOGMEC), commissioned by METI, began a survey and technological development programme for the development of the seafloor polymetallc sulphides (PMS) based on these Plans. The examination of four different fields: the evaluation of the amount of the resource, environmental assessment, mining technology, and processing & smelting technology, are concurrently promoted, aiming for commercialization as soon as possible. Based on the results of research for properties of geomorphology and marine environments of the target test sites in the Okinawa trough, which have been ongoing for several years, the preparation of the pilot lifting test included an in-situ excavation and crushing test conducted using test excavating and crushing systems.

Jan 1, 2018

By Isobel Yeo, Florent Szitkar, Sven Petersen, Sebastian Graber, Nico Augustin, Marcel Rothenbeck, John Jamieson

"INTRODUCTIONSeafloor massive sulfides (SMS) along mid-ocean ridges are often seen as a possible future contribution to a secure metal supply for global human needs. A growing interest over the past few years resulted in six national exploration licenses and one application pending, covering 10,000 km2 each, that have been brought before the UN International Seabed Authority (ISA) since 2011. Each contractor has to explore these 10,000 km2 within the 15-year runtime of the contract. However, the need to define areas that are not economically interesting is more pressing, as 50% of the 100 license blocks have to be returned to ISA after only eight years - hopefully areas that do not contain large and economically interesting SMS deposits. Current geochemical prospecting technologies, however, have mainly been developed for the search for active hydrothermal systems (e.g. hydrothermal vents and associated black smokers) that can easily be traced through physical and chemical anomalies in the water column (temperature, chemical variations of elements such as Mn, Fe, redox potential, and/or the particle concentration in the water column). Such plume surveys have been a primary tool for exploration of SMS systems, but they only identify active, and therefore mostly young and small hydrothermal systems. In a recent high-resolution AUV survey performed within the EU-FP7 funded project “Blue Mining”, we covered 47 km2 along the TAG segment of the Mid-Atlantic Ridge to test exploration methodology for fast and reliable exploration of larger areas of the seafloor for inactive seafloor massive sulfide occurrences using the autonomous underwater vehicle (AUV) “Abyss”."

Jan 1, 2017

By P. E. Halbach

On June 26, 1988, the Jade Hydrothermal Field was discovered in the Okinawa Trough by the German RV Sonne. This research cruise has taken place within the scope of a German-Japanese cooperative project. The Okinawa Trough, located between the Ryukyu Island Chain and the east coast of China, is an active backarc-basin formed by extension within the continental lithosphere. The Ryukyu arc consists of a nonvolcanic outer arc, forming the main island chain and representing compressive highs of the Asian continental margin, and an inner arc with present-day volcanism in its northern part (Sibuet et al. 1988). The valleys and ridges of the trough are cut across by transverse faults, giving rise to younger volcanic intrusions. The Jade Hydrothermal Field was detected in a caldera-like structure. It is. located at about 27°15,0&apos;N and 127°04,5&apos;E with a maxi- mum water depth of about 1650 m. Data of heat flow measurements show a high anomaly in the cauldron basin with values ranging from around 100 to 800 mw/m2 (Halbach et al. 1989). The hydrothermal vent area was discovered in the northern part of the inside northeast slope of the cauldron in a water depth between about 1300 and 1500 m. We identified different varieties of hydrothermal

Jan 1, 1989

By J. C. Wiltshire

Both ferromanganese crusts and nodules present potential processors with enormous volumes of tailings of dubious environmental character: most processing scenarios fail to utilize the uneconomic manganese itself, leaving a total waste volume on the order of 96% of the incoming ore. Each current disposal proposal seems flawed: (1) backhauling to the initial mine site is costly and might run afoul of EPA or UN marine dumping*regulations, (2) subsea disposal near a coastal processing site means almost inevitable community opposition, (3) agricultural soil amendment for improving barren lava or coral rubble appears to require prohibitive amounts of supplementary phosphate, and (4) the slag resulting from an energy intensive pyrometallurgical processing may have potential as road ballast, but few processors will opt for smelting in all but those locales where energy is very cheap. This unfortunately rules out a smelting operation in almost any Pacific Island environment. We envision at least one other scenario which could result in both the removal of tailings from a processing plant and an increase in the supply of useful building materials at little or no cost to either the processing or construction industries--transforming a tenacious waste into a novel resource. Ongoing experiments have demonstrated considerable potential for turning acid leach tailings into dark composite facing stone, fancy black tile, novelty ceramics or concrete aggregate. The tailings are commonly very fine grained and may also serve as an additive in drilling mud. Applications as an additive to asphalt also need to be explored. The metal scavenging nature of ferromanganese minerals should be considered as a radioactive waste disposal matrix. There is no doubt that the greatest challenge will be

Jan 1, 1991

By The DY125-33(Leg 2) Science Parties, Chuanshun Li, Xuefa Shi, Bing Li

"The slow-spreading Mid-Atlantic Ridge (MAR), with a length of ~1.26*104km (Bird, 2003), is the longest mid-ocean ridge on this plant. Separated by the large, left-stepping Equatorial fracture zones, it then be divided into two approximately equal-length parts: Northern Mid-Atlantic Ridge (NMAR, ~6292km) with an average spreading rate of 24mm/yr, and Southern Mid-Atlantic Ridge (SMAR, ~6332km) of 33mm/yr (calculated from PB2002 model, Bird, 2003). Previous works (e.g. Fouquet 1997, Hannington et al., 2011) suggest that slow-spreading ridge could support hydrothermal activities and further favorable for the development of extensive seafloor massive sulfide deposits (SMS). Unlike the NMAR for which large part has been explored for SMS (Hannington et al., 2011; Beaulieu et al., 2015), the SMAR is amongst the least hydrothermal explored spreading ridges until now (Haase et al., 2005, Beaulieu et al., 2015), though both of them show significant similarities in terms of spreading rate, ridge morphology, segmentation, etc. (Macdonald et al., 2001, Sandwell et al., 2014, Tucholke et al., 2008).Before this work, several hydrothermal cruises had been to SMAR since British and German programs starting in 2002, some hydrothermal fields, along with systematic geophysical data, were newly investigated, and types of geologic setting that can host hydrothermal activity were firstly identified (e.g. German et al., 2008; Haase et al.,2005; Haase et al.,2009; Devey et al.,2010; Schmidt et al.,2011).."

Jan 1, 2017

By Gary J. Massoth

Wherever hydrothermal fluids vent from the seafloor they will buoyantly rise (up to 100?s of meters) while mixing with seawater before attaining density equilibrium and dispersing laterally as neutrally buoyant plumes commonly 50 to several 100?s of meters in thickness and with order-of-magnitude or greater breadth. Although these plumes are typically >10,000-fold dilutions of vent fluids they can be reliably detected using sophisticated physical sensing and chemical techniques. Hence, hydrothermal plumes are spatially large targets compared to the actual sites of seafloor fluid discharge and resulting mineralization. For this reason plume prospecting techniques evolved over the past 20+ years have been widely used to systematically explore over 10% of the 60,000-km-long system of mid-ocean ridge (MOR) spreading centers for hydrothermal activity. While plume detection and gradient mapping can be used to home in on venting sites, plume chemical signatures provide additional insight regarding the nature of the fluids being discharged on the seafloor. We have applied the systematic plume prospecting techniques developed on MORs to the volcanic frontal arc setting as part of the NZAPLUME (New Zealand American PLUme Mapping Expedition) surveys. NZAPLUME I in March 1999 marked the first systematic reconnaissance of any intra-oceanic arc for submarine hydrothermal activity. Seven of thirteen previously mapped volcanoes that comprise a 260-km-long section of the southern Kermadec arc northeast of New Zealand were confirmed to be hydrothermally active. On average, one hydrothermally active volcano was found along each 35 km of arc front, a rate comparable to slow- and intermediate-rate spreading MORs. During NZAPLUME II in May 2002, thirteen previously unknown volcanoes and 8 satellite cones were first swath mapped for bathymetric detail and then surveyed using plume prospecting techniques. Three active venting sites were discovered along this 580 km-long arc section, bringing the total to 10, or 39% of 26 volcanoes surveyed overall, still an appreciable frequency rate for venting sites compared to MORs. While only chemical results for NZAPLUME I are available, the arc plumes characterized so far are chemically diverse and rich compared to MOR plumes. This diversity and enrichment was most evident as ultra-high concentrations of CO2, sulfur gases (St = SO2 + H2S), and Fe within plumes over several volcanoes. We suggest the fluids discharging from the seafloor at these sites are volcanic fluids, i.e., hybrid fluids comprised of MOR-like hydrothermal fluids evolved from seawater-rock reaction and fluids exsolved from magma as acid volatiles and liquid brines.

Jan 1, 2002

By Peter M. Herzig

In 1994 and 1998 the German research vessel R/V Sonne undertook detailed mapping and sampling of the largely uncharted offshore areas of the Tabar-Lihir-Tanga-Feni island chain in the New Ireland Basin of Papua New Guinea. The New Ireland Basin occupies a fore-arc position with respect to the formerly active Manus-Kilinailau arc-trench system and hosts a series of Pliocene to Recent alkaline volcanoes which are built on rifted Miocene sedimentary basement. Several of the volcanoes possess high-level porphyry stocks and active geothermal systems, including gold-depositing hot springs and the giant (40 million ounces) Ladolam gold deposit on the island of Lihir. On the southern flank of Lihir island, a group of three volcanic cones were discovered at water depths from 1.000-1.500 m. The volcanoes are located in a narrow zone of recent seismic activity and elevated heat flow (up to 100 mW/m2). The recovered volcanic rocks consist of fresh alkali-olivine basalts, clinopyroxene-rich basalts (ankaramites), porphyritic phlogopite basalts, and trachybasalts. Unusual gold-rich hydrothermal precipitates were recovered from the summit of the 600 m high Conical Seamount located only about 10 km south of Lihir Island. 1200 kg of sampled material systematically collected with a TV-guided grab from the top plateau (150 x 200 m, 1.050 m water depth) are intensely mineralized with pyrite, marcasite, minor sphalerite, chalcopyrite, galena, tennantite/tetrahedrite, and orpiment/realgar together with traces of anglesite, cerrusite, and amorphous silica in stockwork-like veins. Bulk samples of the vein mineralization consist mainly of clays, silica, and disseminated sulfides, and have an unusual high gold content ranging from 1.2-44.0 ppm Au. In some of these samples, grains of native gold (about 1 micron in diameter) were identified by SEM in pyrite and sphalerite. The gold-rich material also contains high concentrations of silver (up to 1000 ppm) and typical epithermal elements such as As (2.6 wt.%), Sb (0.2 wt.%), and Hg (34 ppm). Similar to epithermal deposits on land, which usually have only low base metal contents, the samples from Conical Seamount contain only minor amounts of Zn (max. 4.5 wt.%), Cu (2.0 wt.%), and Pb (2.0 wt.%). Many of the samples recovered from Conical Seamount are virtually identical to the gold ore at Lihir.

Jan 1, 1998

By Peter A. Rona

The recent discovery of the first black smoker-type hydrothermal venting and massive sulfide mineral deposits at a site in the rift valley of the slow-spreading Mid-Atlantic Ridge near latitude 26°N, longitude 45°W (Rona et al., 1986, Nature, 321: 33-37), demonstrates that a complete series of hydrothermal mineral deposit types exists at slow-spreading oceanic ridges (half-rate = 2 cm/y), similar to the series previously known at faster-spreading oceanic ridges (half-rate > 2 cm/y). The largest hydrothermal mineral deposit known at a seafloor spreading center is a stratiform massive sulfide body with bulk dry weight of about 100 x 106 metric tons in the Atlantis II Deep at the slow-spreading axis of the Red Sea. This observation invalidates the concept that size of a hydrothermal deposit is directly proportional to rate of seafloor spreading. Instead, the occurrence, grade and size of a hydrothermal deposit formed at a seafloor spreading center is controlled by anomalous chemical and physical conditions which may occur at extremely localized sites at the full range of spreading rates. The basic hydrothermal process involving subseafloor hydrothermal convection driven by magmatic heat sources appears to be similar at slow- and faster-spreading centers. However, differences exist in the periodicity of magmatic cycles that energize hydrothermal circulation (104 y at slow-spreading centers; 103 y at faster-spreading centers); in the distribution of hydrothermal sites along a spreading axis (estimated 100 km along slow-spreading centers; 10 km along faster-spreading centers); and in residence time

Jan 1, 1986

By Stephan K. Schwank

In mid 1993, Bauer Spezialtiefbau GmbH, based in Germany got the order to develop a sampling tool capable of penetrating all different types of seabed sediments including cobbles and boulders and into bedrock. BHP and their partners Benguela Concessions Ltd., had been convinced by the Bauer Trench Cutter Technology and a large scale test in Germany that this system will be the right one to fulfill their expectations for sampling the diamond area off the coast of Namibia. The technique of the tool is based on Bauer&apos;s standard cutter technology, which is widely used for the installation of cut-off and diaphragm walls all around the world. The two counterrotating cutter wheels with 12.1 tom torque each cut an area of 3 x 1.2 m (up to 3 x 3 m are possible). The material mixed with seawater was then pumped to the separation plant on board the vessel Geomaster with a capacity of approximately 700 m3/h. Cutter wheels and mud pump were mounted on a special cutter frame and connected by wire ropes and hydraulic hoses to the vessel. An outer frame with four telescopic legs supported the cutter vertically on the uneven seabed and allowed a controlled penetration of the tool up to 6 m into the diamond bearing ground. The tool required a total power installed of approximately 800 kW. All hoses, the 6-inch mud hoses as well as the hydraulic hoses, were stored and compensated on drums on board suitable for a water depth of up to 200 m. Launch and recovery of the tool was effected through the moon pool of the vessel and the 25 m high, special designed drill tower. The 65? to sampling tool had been commissioned in early 1994 in Cape Town. After intensive testing the sampling programme of more than 4000 holes could be successfully completed by January 1995.

Jan 1, 1998