Search Documents

By Bernard S. Borie

THE U-A1 binary system has been studied by Kaufmann and Gordon.' They have shown that three intermetallic compounds occur in the system: UAl², UAl², and a third compound tentatively identified as UA15. UA1³ is simple cubic, a, = 4.26A. Its unit cell contains one formula weight, and it is iso-morphous with AuCu³. UA1² is face-centered cubic, a, = 7.72A, with eight formula weights per unit cell. Rundle and Wilson have shown that it is iso-morphous with Cu²Mg.² A Debye-Scherrer pattern of the Al-rich compound indicated a more complex structure than either UA1² or UA1³. The following is a report of an investigation of the crystal structure of this compound and a determination of its stoi-chiometric formula. A melt of uranium (99.9 pct pure) and aluminum (99.9 pct pure) was prepared which contained about 25 pct U by weight. It was cooled from 950" to 650°C at a rate of 500" per hr and then taken from the furnace and air cooled. An X-ray diffraction pattern of the ingot showed only lines of aluminum and the Al-rich compound. Filings from the ingot were reacted with a solution of sodium hydroxide, producing a fine black powder, the diffraction pattern of which showed no traces of aluminum. A comparison of the Debye-Scherrer pattern of our sample with the data published by Kaufmann and Gordon1 showed that it is identical with the Al-rich phase which they reported. Single crystals were obtained by cooling the melt more slowly (about 50°C per hr). After reaction with sodium hydroxide, the crystals appeared as small black needles attached to the ingot surface. Cell Size, Space Group, and Uranium Positions A series of Weissenberg photographs for rotation about two of the crystallographic axes, taken with copper radiation filtered through nickel foil, revealed an orthorhombic cell of dimensions: a = 4.41 ± 0.02A b = 6.27 ± 0.02A c = 13.71 ± 0.03A Reflections of the type hkl were observed only if: h + k + I = 2n, of the type hkO only if: h = 2n and k = 2n, of the type h01 only if: h + 1 = 2n, and of the type Okl only if: k + 1=2n. Hence, the cell is body-centered with an 001 glide plane. The evidence for the existence of the glide plane is the observed extinction of 23 possible re- flections of the type hkO with at least one index odd. There are only two space groups consistent with these data: C"" — I2ma and D28 2h — Imma.³ he possible sets of atomic positions for these space groups are: 12ma: (0 0 0; ½ ½ ½) + 4: (a) x 0 %; x % % (b) x ¼ z; x ¾ Z 8: (c) x y z; x y z; x, ½ + y, Z x, M - y, z Imma: (0 0 0; ½ ½ ½) + 4: (a) 0 0 0; 0 ½ 0 (b) 0 0 ½; 0 ½ ½ (c) ¼ ¼ ¼; ¾ ¼ ¼ (d) ¼ ¾ ¾ ; ¾ ¾ % (e) 0 ¾ Z; 0 ¾ z 8: (f) x 0 0; x 0 0; x 1/2 0; x ½ 0 (g) ¼ Y ¼; ¾ Y ¾; ¾ y ¼; 1 y ¼ (h) 0 y z; 0; ;; 0, ½ + y, z; 0, l/2 - Y, Z (i) x 1/4 z; x ¾ z; ¼ z; x ¾ z 16: (j) xy z; x y z; x y z; x y z; x, ½ + y, Z; x,½ - y, z; x, ½ - y, z; 11 1, + y,Z Though density measurements on different samples were found to vary somewhat, they were all within the range 5.7 * 0.3 g per cu cm. If it is assumed that the unit cell contains four formula weights of UAl,, it is 6.5 g per cu cm. If there were as many as eight uranium atoms per unit cell, the

Jan 1, 1952

By W. J. Taylor

Nature has furnished us with fuel in three forms, solid, liquid, and gaseous; solid, the most common; liquid, containing the greatest energy; gaseous, the most convenient for use. The tendency of the day is to the conversion of solid and liquid fuel into the gaseous form. There is magic in the word gas to many men who through ignorance or indifference imagine that by mere conversion into gas an immense quantity of energy can he added to fuel of other forms, forgetful of the law of nature, that. the conversion of any substance from one form to another involves a loss of effective energy, and therefore that if in certain cases more duty can be obtained out of the gas resulting from a given amount of coal than the coal itself will supply when used direct, the cause lies solely in the more efficient utilization of the fuel in its gaseous state. Nevertheless, new processes for making gas are constantly crowded upon our notice with claims of less cost for manufacture and delivery than natural gas, and often of far more energy for the product than is contained in the coal or oil from which it is made. I was recently asked to examine a new process of this kind. From an analysis shown me the calorific energy of the gas approximated 375 heat-units per cubic foot; on ascertaining the quantity of gas claimed to be made from a given amount of solid and liquid fuel, it appeared, that for every 325 heat-units contained in the latter 900 heat-units were alleged to he delivered into the gas, or nearly three times as much energy as the original fuel really held. The extravagant claim of some oil-gas advocates is still frequently heard, that by vaporizing oil with steam and then passing the mixture through a coil of hot iron pipe, an oil-water-gas containing 26,600 heat-units is formed from 1 pound of oil carrying originally 21,000 heat-units, while the only energy expended on the gas has been by the introduction of a -little steam and a little extraneous heat. Theoretically, 1 pound of oil converted into water-gas carries 26,600

Jan 1, 1890

By H. W. C. Prommel

While Utah remains an unimportant factor in oil production, exploratory drilling was carried on in six widely separated areas, extending from the southwest to the northeast corner of the state. One new gas field, the Last Chance or Starvation Creek anticline in Emery County, and two new gas horizons in the Clay Basin field of Daggett County, were thereby discovered during 1934. Exploratory Drilling South Central Utah Emery County—Last Chance Anticline.—The test of the Ramsey Petroleum Corporation in sec. 18, T.26S., R.7E., on the apex of this anticline (vert. closure 700 ft.; area within closing contour line, as mapped by U.S. Geological Survey, 26,000 acres) encountered gas in the Moenkopi formation of lower Triassic age at depths ranging from 2530 to 2863 ft. The total thickness of sandstone, sandy shale and -limestone beds in which gas was encountered is approximately 50 ft. The well was tested at a depth of 2755 ft., gaging 21,000,000 cu. ft. of gas, R.P. 410 lb. The well is being plugged back to the lowest gas horizon at 2771 ft. from a total depth of 3168 ft. Gas from this well probably will be used for the drilling of a second well structurally lower, to test the oil possibilities of the Moenkopi formation as well as of the upper and lower Pennsylvania formations, of which the latter so far remains untested in South Central Utah. The well was not drilled deep enough to determine more definitely the western margin of the petroliferous Paradox Basin of lower Pennsyl-vanian age of southeastern Utah. Woodside Anticline.—This field, lying immediately northeast of the San Rafael swell, contains, according to maps of the U.S. Geological Survey, 8380 acres within its lowest closing contour line 700 ft. below the apex. A well was drilled by Utah Oil Refining Co. at the apex in sec. 12, T.l9S., R.l3E., during 1924. Gas was encountered in the Moenkopi and Kaibab formations of Triassic and Carboniferous (Permian) age respectively. The flow is estimated at 21,000,000 cu. ft., R.P. 900 lb.,

Jan 1, 1935

By ROBERT R. ABUOTT

(Cleveland Meeting, October, 1912.) THE practice of carbonizing steel for the purpose of case-hardening has assumed great commercial importance within the past, 10 years. Formerly, case-hardened steel was held in more or less contempt, since it. was considered a cheap substitute for tool-steel. This is no longer the case. The development of the motor-car industry, and coincidentally that of modern alloy-steels, has resulted in overcoming many difficulties formerly experienced in case-hardening. This result has been accomplished by increased knowledge regarding the analysis of the steel which would respond most readily to case-hardening, and by more careful methods of treatment of the carbonized steel. The ordinary method of carbonizing consists in packing the steel with the carbonizing-material in cast-iron boxes and placing them in a furnace at a temperature of from 1,500° to 1,900° F. for a time sufficient to give the required depth of cc case." The steel is then either quenched directly from the box, or is allowed to cool without unpacking, and finally given a single hardening-heat., or, for special work, two or three heats. During the year 1911, more than 100,000 tons of carbonizing-material was sold in the United States, at an average price of probably $55 per ton. More than 85 per cent. of this material consisted of granulated bone. Within the past four years, many manufactured compounds have been placed on the market, consisting largely of some form of carbon or carbonaceous material, with or without the addition of chemicals. Steel will absorb carbon placed in contact with it at the temperature of the atmosphere. The reaction is exceedingly slow, but. increases rapidly with increasing temperature. Below * Metallurgical Engineer, The Peerless Motor Car Co.

Dec 1, 1912

By Emil Gathmann

(San Francisco Meeting, September, 1915) THROUGH wide experience at numerous mills in the United States I have found that there is a decided difference of opinion among the producers of steel as to what constitutes commercially sound steel. Some metallurgists insist upon having, for certain grades of steel, a so-called "open steel," -i.e., one which contains numerous blowholes of varying sizes, and consequently but little volume of true pipe, although a central intermittent shrinkage cavity often extends well down into the ingot: Such blowholes and pipe are expected to weld up during rolling or forging, because their surfaces are not oxidized. Even if this be admitted, included slag particles and a high degree of segregation are bound to be present in the product of such ingots. Blowholes are the result of an oxidized heat, and all heats, unless made or finished in the electric furnace, are oxidized more or less. Subsequent deoxidation, or rather degasification, either in the ladle or in the mold, or in both, is necessary to reduce or prevent blowholes. As is well known, a greater yield of billets or sheets is secured from the ingot by allowing the formation of blowholes, but this is undoubtedly obtained at the expense of the quality of the product. Decided segregation of carbon, phosphorus, and sulphur, as well as small included slag particles, undoubtedly exists throughout the greater portion of all so-called open steel, and cannot be removed by cropping. The first requisite for sound, homogeneous steel ingots and blooms is therefore, in my opinion, so to treat the steel in the furnace, ladle, and mold that "piping" steel is produced. The line of demarcation between harmful and so-called "harmless" blowholes is practically impossible to define. Is it not, therefore, the better and safer practice to use means for the elimination of blowholes and correspondingly reduce the segregation and allow the formation of a well-defined shrinkage cavity or pipe .at the upper end of the ingot? With the relatively cheap deoxidizers available at the present time, e.g., ferro-silicon, aluminum and titanium,

Jan 8, 1915

By Joseph Bernhardt

THE Cornwall Ore Mines, Division of the Bethlehem Steel Co., at Cornwall, Lebanon County, consists of two separate magnetite ore bodies, approximately one mile apart. The one ore body was an outcrop in which open-pit mining operations were begun in 1742 and continued without interruption. This mine is also served by a shaft for mining that portion of the ore body not recoverable by open-pit methods. The other property had no outcropping and is entirely an underground operation. This mine, cap-tioned No. 4 mine, is serviced by two shafts 220 ft apart. The No. 4 shaft is for hoisting rock and ore, and the No. 5 shaft is for handling men and ma- terials. The shafts are on a catenary curve, closely following the dip of the ore body. Slope of the shafts at the collar is 36", flattening to 26" at the bottom. The footwall at Cornwall is a traprock which varies structurally from solid to highly fractured. Grizzly stations at the top of each chute raise were reinforced by setting timber sills on concrete. Occasionally it was necessary to concrete the entire chute raise. Concreting was done by using 35-yd electric mixers set up in the breaking subs. Sand, stone, and cement were hoisted up through the chute raises to the breaking subs. Late in 1937 it was decided to eliminate chute raises and breaking subs in future development. Haulage levels are 50 ft apart vertically. When ore is below a 40 " dip, slushing drifts are driven normal to the haulages and on 40-ft centers. In a few areas, ore dips greater than 40" and slushing drifts are then placed parallel to the haulage drifts. Finger raises are opposite each other and on 20-ft centers making 20x20-ft draw areas (fig. 1). For loading

Jan 1, 1951

By Joseph Bernhardt

THE Cornwall Ore Mines, Division of the Bethlehem Steel Co., at Cornwall, Lebanon County, consists of two separate magnetite ore bodies, approximately one mile apart. The one ore body was an outcrop in which open-pit mining operations were begun in 1742 and continued without interruption. This mine is also served by a shaft for mining that portion of the ore body not recoverable by open-pit methods. The other property had no outcropping and is entirely an underground operation. This mine, cap-tioned No. 4 mine, is serviced by two shafts 220 ft apart. The No. 4 shaft is for hoisting rock and ore, and the No. 5 shaft is for handling men and ma- terials. The shafts are on a catenary curve, closely following the dip of the ore body. Slope of the shafts at the collar is 36", flattening to 26" at the bottom. The footwall at Cornwall is a traprock which varies structurally from solid to highly fractured. Grizzly stations at the top of each chute raise were reinforced by setting timber sills on concrete. Occasionally it was necessary to concrete the entire chute raise. Concreting was done by using 35-yd electric mixers set up in the breaking subs. Sand, stone, and cement were hoisted up through the chute raises to the breaking subs. Late in 1937 it was decided to eliminate chute raises and breaking subs in future development. Haulage levels are 50 ft apart vertically. When ore is below a 40 " dip, slushing drifts are driven normal to the haulages and on 40-ft centers. In a few areas, ore dips greater than 40" and slushing drifts are then placed parallel to the haulage drifts. Finger raises are opposite each other and on 20-ft centers making 20x20-ft draw areas (fig. 1). For loading

Jan 1, 1951

By Horace R. Graham

CHEMICAL nitrogen and the "nitrates" of commercial significance are derived mainly from three basic sources: (1) the natural deposits in the form of nitrate-bearing earth and clay, which, being largely water-soluble, can exist only in the most arid portions of the earth; (2) coal, which yields not only nitrogen but also the additional by-product hydrogen required for the synthesis of ammonia and its compounds; (3) the atmospheric air, which contains 75.5 pct by weight of pure nitrogen gas. NATURAL NITRATE DEPOSITS Occurrence Although natural nitrate deposits consisting principally of the salts of sodium and potassium have been reported in Egypt, South Africa, Mexico, Argentina, Colombia, Peru and the USA, the only known natural nitrate resources of commercial importance are the vast deposits found in the Atacama, Tarapaca and Antofagasta regions of northern Chile, lying in a narrow strip 10 to 50 miles wide and roughly 450 miles long, between latitudes [19O] and [26OS]. In addition to yielding nitrates of sodium and potassium, these deposits are the source of the major portion of the world's supply of iodine. The nitrate-bearing ores known in Chile as caliche are variable in composition and may contain from 5 to 30 pct each of nitrate, chloride and sulphate. While the deposits are present chiefly in the form of the sodium salt, potassium, magnesium and calcium also occur in percent- ages from 0.1 to 5; usually as double salts with sulphate, which are but slightly soluble in nitrate leach solutions. These double salts are bloedite(Na2S04.MgS04.4H,0), glauberite (Na2S04.CaS04), polyhalite (K2SO4.- MgS04.2CaS04.2H20). Some deposits contain up to30 pct of their ni-

Jan 1, 1949

By T. H. Aldrich

The Aldrich Mining Go. holds under lease from the Illinois Central R. R. Co. about 14,000 acres, in the east half of Township 12, Range 12 W., in Marion county, Alabama, and owns other lands, of which about 1,000 acres adjoin this leased tract, making a total area of about 15,000 acres, all of which is underlain by the coal-seam upon which the company is operating. This seam is nearly horizontal; and a ravine, diagonally crossing the tract, exposes the outcrop on either side for about 2 miles. The territory has been so divided that nearly the whole of it can be worked out by two collieries. The mines at Brilliant were opened in the fall of 1898, and shipments began in the following spring. The original plan was to furnish steam-coal for locomotives to the Illinois Central R. R. Co.; and upon this expectation the investment of capital was made. The field was entirely new; and the softness of the coal at the outcrop induced the belief that it could be very cheaply mined. A contract for the delivery of a large quantity of coal to the railroad was accordingly executed. But with the advance of' the entries to increasing distances from the outcrop, the coal proved so hard that it could no longer be drilled with a breast-auger; and the expense of mining became so great that the contract for cheap steam-coal had to be canceled. It became evident that the work must be done with machinery and explosives, if it could be profitably done at all. On the other hand, the excellent quality of this coal opened, at the same time, a possible market not specially contemplated at the outset—namely, that of a first-rate coal for domestic and general uses. Since no other deposit of such coal was known to exist on the line of the Illinois Central, or any other railroad

Jan 1, 1907

By David S. Butts

There are many solution mining operations that use solar ponds as a mineral recovery step. Other locations in the world are now under investigation to recover minerals by solution mining but require the cheap energy of solar ponds to make the recovery viable. This paper shows a step-by-step material balance system that can be used in both simple and complex solar ponds. Use of this system will help the engineer determine if solar ponding efficiency can be improved or if solar ponding will work at all with a given set of conditions. Even the most complicated solar pond can be reduced to six flow streams. These are (1) feed, (2) exit, (3) leakage, (4) entrainment, (5) salts, and (6) evaporation. The equations developed in this paper will allow the solar pond engineer to easily evaluate the effect of each of the flow streams on the mineral production of a pond or pond complex.

Jan 1, 1985

[ ]

Jan 1, 1907

By E. De Golyer

THE petroleum production of the world, in 1923, for the first time reached the billion-barrel mark. A preliminary estimate of production is 1,014,413,000 bbl., an increase of 159,604,000 bbl., or 18.6 per cent. over the 854,809,000 bbl. produced in 1922, the year of next highest production. This increase resulted from an increase of 178,469,000 bbl. in the production of the United States; the total for the rest of the world shows a loss of 18,865,000 bbl., a loss caused by the decrease of approximately 32,278,000 bbl. in Mexican production. The Mexican decrease more than offset increases in the production of Russia, Persia, Roumania, Venezuela, Sarawak, and various minor fields. The increase in production for the United States, and consequently for the world, was the result of flush production from development to maximum capacity during the year of eight, bonanza fields-fields reaching daily yields of 100,000 bbl. or better. It might be ascribed more exactly to the production from the three flush fields of the Los Angeles basin. Their production alone was greater than the increase in the world petroleum production, or the increase in the production of the United States, and it was cheap oil from these fields that demoralized the oil markets of the world. The Basin fields were. the features and dominating factors in the oil industry of the world during 1923. The bonanza fields of 1923, their estimated production for the year, and peak are given in Table 1.

Jan 3, 1924

By Max W. Ball

Our ever-increasing use of minerals has been the outstanding fact in our American economic development. The rise in our standard of living in the past century is without equal in human history. Nowhere in time or place has the man who works lived so well, or the man who cannot work been so well cared for. We live in a new world, even the poorest of us, that our forebears of 1849 could not have dreamed. That new world has come mainly from our use of minerals. Our per capita use of nonmineral products has grown too, but by only a modest amount. Food consumption per person has grown about 15 per cent in the past fifty years; lumber use per person ,has fallen 56 per cent and that of wood for fuel 65 per cent. Of all the products of field and forest, our use, per capita, may have increased by one fifth during the present century. In contrast, our per capita use of minerals has multiplied several times. Each of us uses 2% times as much steel and 16% times as much petroleum as our fathers used in 1900. In less than half a century our per capita consumption of all minerals has probably risen by 200 to 250 'per cent. Man once built with wood; today he builds mainly with brick and stone and steel. Once he traveled by the power of hay and oats; today he travels by the power of coal and oil. Rubber made from minerals is already better for some uses than rubber tapped from trees; before long it will be better for most and perhaps all uses. Even our ladies' graceful legs are clad in mineral fiber, where once animal or vegetable fiber would have covered them. Our high standard of living is a product of the machine.. The machine is made of minerals. The machine is driven by minerals. The machine age is a mineral age.

Jan 1, 1949

By Herbert Dlaska

The BBU - rotary hearth treats lead concentrates and battery scrap by the roast-reaction process. It corresponds in principle to the long-known Newnam hearth, however its hearth-basin is not straight but curved to a closed ring. In operation this annular hearth is filled with liquid lead and rotates around a central blast-box. The charge, heated to a glowing-red, floats on top of the lead bath, into which air is blown from the blast-box through a horizontal slot-type tuyere. Ore pellets and brown coal are continuously charged onto the reacting mass from two storage bins. Lead is set free by the roasting reactions and trickles through the charge into the lead bath from where it is tapped from time to time. The reacting mass is continuously stirred by a mechanical agitator and backed, by a mechanical shovel, against the water-jacketed wall of the blast-box. The gangue of the charge forms lumps of scorified character, the so-called hearth slag or grey slag, which are discharged from the hearth. The waste gases are collected in a hood and conducted to a baghouse from where the fumes and dust are automatically transported to the pelletizing installation and are recycled with new material. The daily output of lead bullion depends mainly on the lead content of the charge. With lead concentrates containing 74% lead, about 24 tons of lead bullion per day are produced on the hearth at a direct lead recovery of about 89 per cent. Approximately 10 per cent of the lead content of the new material passes into the hearth slag from where it can be recovered in a blast furnace or in a rotary furnace. For small lead smelters the BBU-process represents the most economical way of melting high-grade lead concentrates. The process requires a relatively small capital investment, consumes little fuel, utilizes cheap fuel and is very flexible. Further, of great importance, is the fact that battery scrap can be treated by the BBU-process with very good results.

Jan 1, 1970

Jan 1, 1916

By E. P. Pfleider, W. G. Pariseau

This paper reports the theoretical and experimental results of an analysis of ore pass drawdown as a problem in soil plasticity. The method of analysis developed appears to be a promising technique of investigating the mechanics of fragmented materials. A reconstructed plasticity theory brings experiment and theory into reasonable agreement, and hence may provide the foundation needed for rational ore pass design. The gravity-induced movement of broken rock through ore passes is an economical method of transporting fragmented materials through large vertical distances in underground mines, provided the ore pass is well designed. Unfortunately, the design procedures now followed do not very often result in ore passes that function properly. On the one hand, the huge accumulation of empirical data pertaining to the movement of materials in gravel bunkers, storage bins, deep grain silos and other structures that have features in common with ore passes remains uncorrelated. On the other hand, there is a dearth of experimental data substantiating theoretical models of material behavior. Consequently, reliable generalizations encompassing the broad spectrum of problems involved have not been forthcoming. AS an initial step towards improving the situation, a detailed case study of two-dimensional ore pass drawdown was made. The mechanics of the process were analyzed theoretically as a problem in soil plasticity and tested experimentally through observations of a laboratory ore pass model. THEORY Taylor1 defines a soil as a "mass commonly considered to consist of a network or skeleton of solid particles, enclosing voids of varying size." Broken rock in an ore pass is such a material. In plasticity theory this material is replaced by an idealized substance that deforms elastically up to some state of stress at which slip or yield occurs,2 For com-pressive states of stress, the Mohr-Coulomb criterion is a satisfactory yield condition. After the yield point is reached, the ideal soil deforms in accordance with the concept of plastic potential.4 Under plane strain conditions the governing equations separate into a system of stress equations and a system of velocity equations.' Only stress variables appear in the stress system. The velocity system, however, contains a stress variable. The two systems are, therefore, coupled. Both systems are hyperbolic, and each has two real, distinct families of characteristic curves that coincide according to the classical theory of ideal soil plasticity. The

Jan 1, 1969

By K. F. Veith, R. L. Marovelli, T. S. Chen

An analytical study is made of thermal stress distribution in a thin circular disc subjected to a peripheral thermal shock at various rates of heat transfer. The problem is of importance in predicting the thermal shock response of a rock body of finite size. The theoretical analysis is based on radial heat flow by conduction in the disc and heat exchange by convection between the disc and the surroundings. The case of constant properties and plane stress is treated. Solutions of the stress distribution are presented for both cooling and heating shocks and an average stress theory is formulated. Preliminary experimental verification was obtained from the results of shock tests on thin rock discs insulated on both flat end faces so that heat exchange took place through the exposed peripheral surface. Physical properties vital to the analysis are Young's modulus, tensile strength, coefficient of linear thermal expansion, thermal diffusivity and thermal conductivity. Plots of these properties are presented. Historically, thermal energy has been used for primary rock removal throughout the ages. Although it is not widely known, the fire-setting method of thermal rock fragmentation was still in use 100 years ago in systematic underground mining operations in Scandinavia.' There, the availability of cheap labor and abundant wood fuel made the method competitive with the early blasting powders. By 1880, as high explosives replaced powder, use of the method declined and it was finally abandoned about 1885. Only 40 years ago, some experimental fire-setting methods were used for rock removal underground at Pribram and Zinnwald in Central Europe.2 Compressed air-oil burners replaced the earlier wood fuels. About 15 years ago, gaseous oxygen-oil burners were introduced in the United States and gained acceptance for difficult blasthole drilling and some quarry opera- tions. At present, there is renewed interest in the compressed air-oil burner designs. The literature included information on thermal secondary processes for rock weakening or particle liberation3,4,5,6,7,8 on thermal spallation of rock 9,10,11,12,13 and on the thermal fracture of materials other than rock. The 1955 Symposium on Thermal Fracture14 and the later work of Hassel-man, cover recent developments in thermal shock investigations on brittle ceramics. Although the number of published analytical and experimental investigations conducted on ceramic and refractory materials is large, the literature reveals that there is a lack of information on both the theoretical and actual response of rock to thermal shock. Many of the thermal shock studies on ceramic and refractory bodies are based on the case of heat transfer at the solid's surface by convection in either liquid or air. A similar heat transfer situation was adopted for a theoretical analysis of the thermal stresses in a thin circular disc subjected to a peripheral thermal shock. Experimental thermal shock tests were then conducted on rock specimens to check the analytical results. Specially insulated quartzite, basalt and taconite discs were shocked in either liquid or still air bath at various rates of heat transfer. The work was done in order to resolve the question as to whether theoretically determined tensile stresses are actually realized in a finite rock body undergoing thermal shock. Specifically, if theory predicts that the tensile strength of a rock should be exceeded in a particular type of controlled thermal shock, will fracture occur? This information is needed by Bureau researchers working on thermal and electrical rock fragmentation methods. The object of this paper is to present the main features of the theory and procedure being used in the authors' approach to quantitative prediction of rock response to a thermal shock. THEORETICAL ANALYSIS In the analysis to follow, simple geometry of a thin circular disc is considered. The disc is assumed to be isotropic, homogeneous and perfectly elastic, and to have constant thermal and mechanical properties. The effect of radiation is neglected so that heat is transferred by conduction inside the disc and by convection with its surrounding. In addition, the end

Jan 1, 1967

Jan 1, 1968

[L. W. KEMPF, Chairman E. E. SCHUMACHER, Past-Chairman E. A. ANDERSON, Senior Vice-Chairman A. A. SMITH, JR., Vice-Chairman 11. A. MALONEY, Treasurer ERNEST KIRKENDALL, Secretary 29 West 39th Street, New York 18, N. Y. Executive Committee 1947 C. Y. CLAYTON A. B. GRENINGER CURTIS PIGOTT 1948 WALTER BONSACK W. A. DEAN LOUIS JORDAN 1949 J. D. HANAWALT W. A. JOHNSON E. W. PALMER]

Jan 1, 1946

Jan 1, 1963