Search Documents

The Use of Automated Mineralogy to Interpret the Batch Flotation Performance of Merensky Reef Ore

Sep 13, 2010

By C. Musingwini

The Bushveld Complex is economically significant and strategically important to South Africa, thus it is imperative that optimal extraction of platinum group metal (PGM) resources on the Bushveld Complex is achieved. Optimal extraction broadly requires that the maximum amount of ore is extracted by excavating and hauling the minimum amount of waste in the shortest possible time, at the least cost, and in the safest and most environmentally acceptable manner. In open-pit mine planning this entails among other things, minimizing the waste stripping ratio, whereas in underground mine planning it includes minimizing the metres of waste development. In conventional mining, the main development that is in waste or partly in waste and defines the mining grid pattern includes levels and raises. It was prudent to consider optimizing level and raise spacing in conventional mining because the method is a prevalent mining method on the Bushveld Complex accounting for nearly 70% of platinum production.

Jan 1, 2010

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. sand and gravel mining workforce from March through September 1986. Similar reports have been prepared for the metallic, stone, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

By Belcher C. B

A procedure was required for the rapid determination of silicon in low-alloy irons and a suitable method used the formation and reduction of silicomolybdic acid at 50°C. The procedure gives results for elemental silicon and this enables the correct computation of oxidation requirements in basic oxygen steelmaking. The method could be useful in iron foundries which have not installed direct reading spectrometers.INTRODUCTIONOxygen steelmaking experiments required rapid determinations of 0,5-1,6 per cent silicon in iron (3-4 per cent C) within 10 min of sampling; a reproducibility better than ±0.03 per cent Si was desired. Only elemental silicon (Si°) is of interest as a fuel in basic oxygen steelmaking technology, and the proposed procedure determines exclusively this form of silicon. The method is described as it may prove useful to other workers although the interference study would be incomplete for some applications.The analysis of silicon in iron is frequently obtained using direct reading spectrometers, but for the proposed experiments the spectrometers could not be used because of the prohibitive distance from the furnace. It should be noted that spectrometers determine both the elemental silicon and that present as silicon dioxide in occluded slag and inclusions.The silicon content of iron and steel is determined in this laboratory by spectrophotometric measurement of a "molybdenum blue" colour. The reactions involved have been extensively investigated; Strickland (1952) showed that a...

Jan 1, 1965

Reduce the potential for injuries in underground mines by providing an alternative to manually lifting and holding heavy roof-support beams. The Problem I-beams, rail sections, and wooden cross-beams are often used in mine haulageways where extensive roof support is needed. Studies by the Bureau of Mines have shown that many mines must resort to manually lifting, moving and installing these beams. Such manual-handling activities have the potential for causing injury to mine workers, particularly back injuries. I-beams used for roof support can typically weigh from 400-500 lbs. Rail sections weigh about the same as the I-beams. Wooden beams can weigh from 200 to 300 lbs. To lift a single beam usually requires the efforts of 3 to 5 mine personnel.

Jan 1, 1988

By Gerald E. H. Verbeek

As the number of driven concrete piles with Embedded Data Collectors increases, it has become possible to compare the widely used Beta Method to assess pile damage (using the change of pile impedance) with the so-called Measured Pile Integrity (MPI) method (a combination of two approaches using both the change of pile impedance and the change in pile pre-stress levels). After a brief introduction of both methods, this paper presents the outcome of that comparison based on data from more than 400 concrete piles driven in Florida, which brings into question the reliability of any damage assessment method based solely on the change of pile impedance (such as the Beta Method), especially to detect damage near the pile toe. Moreover the paper demonstrates the need to re-assess the damage classification used for the Beta Method as well as the use of Pile Driving Analysis (PDA) to detect pile toe damage.

Jan 1, 2011

By J. Brent Hiskey

Thiourea is a reagent capable of complexing gold and silver. With the proper oxidant, thiourea can effectively dissolve metallic gold and silver. A thiourea leaching system possesses potential advantages over conventional cyanidation including acidic solutions instead of alkaline, cationic complexes in contrast to metal-cyanide anoionic complexes, and faster leaching rates with acidic solutions of thiourea. Generally, the rate of metal dissolution in thiourea solution is fastest when ferric ion is employed as an oxidant. Acidic thiourea solutions for certain applications could offer a nontoxic and noncorrosive option for processing gold and silver. This paper provides information regarding the fundamental chemistry of the acidic thiourea system, and reviews the dissolution of both silver and gold in acidic solutions of thiourea. The recovery of gold and silver from acidic thiourea solution is discussed.

Jan 1, 1981

By M. D. Balen

The U. S. Bureau of Mines has undertaken the development of mineral industry cost escalation factors to enable the estimation of mineral development and extraction costs for mineralized sites in Alaska throught the use of the Bureau's Cost Estimating System v2.0 (CES 2.0). For the purposes of this document, all calculations are based on, and reflect the economic environment in Alaska in July 1992. The greater cost of mining in Alaska as compared to the contiguous-48 States can be estimated for Alaskan mining operations through (1 ) the analysis of capital and operating costs for analogous mine and mill plants in operation in the contiguous-48 States; (2) the hypothetical relocation of mine and mill plants from their actual location(s) to Alaska by making engineering modifications to the mine and mill plant design as required by the Alaskan site characteristics; (3) calculation of the cost of the required engineering modifications and; (4) the escalation of all costs to a level representative of the economic environment in Alaska at some specific point in time.

Jan 1, 2011

By William R. Yernberg

The Cripple Creek & Victor Gold Mining Co.(CC&V) celebrated completion of a two-year, $168.5-million expansion and capital improvement program. An open house celebration was held in the historic mining town of Victor, CO on Oct. 4, 2002. Hundreds of townspeople, the press and other invited guests from the mining industry joined the employees of CC&V in the celebration. The event included mine tours, company displays and a barbecue picnic, complete with a country and western band. The Cresson Mine is located about 40 km (25miles) west of Colorado Springs, CO between the towns of Cripple Creek and Victor. The mine is the only large-scale gold mining operation in Colorado and now employs about 300 (ME, October 2001, pp.21-28). The operation is a joint venture between Anglo-Gold (Colorado) (67%), based in Greenwood Village, CO, and Golden Cycle Gold (33%), based in Colorado Springs. CC&V is managed by AngloGold North America. AngloGold North America is the U.S. subsidiary of AngloGold, the world’s second largest gold mining producer. AngloGold is based in Johannesburg, South Africa.

Jan 1, 2002

By D. B. Lovett

The work described in this report was directed toward identifying and devising methods to minimize the previously observed variability between working level hour exposures and the alpha particle track densities resulting on Track Etch films exposed to mine atmospheres containing radon and radon daughters. The disequilibrium between radon and its daughters was shown to directly affect this Track Etch film calibration factor. The wide range of disequilibrium states possible in mine situations amply explains the variability in the previous tests. A file of published mine atmosphere composition data was compiled and was used, along with atmospheric compositions derived from several theoretical models ref the atmospheric behavior, to evaluate the variability of several dosimeter configurations and concepts. A nonlinear, iterative regression analyse; was formulated that successfully predicted working levels to within 8 to 10% from only the alpha particle activities (Rn, RA, and RaC') data such as are obtainable from Track Etch films over a wide range of disequrlibrium conditions. A model expressing atmospheric concentrations as a function of radon source strength, plate out rate factor, ventilation rate and the fractional re-entry by recoil of previously platted-out daughters was derived and used in the regression program in addition to preparing a set of reference tables and graphs showing the disequilibrium behavior of the atmosphere. Other factors that can affect the Track Etch Film response writ considered and shown to he less crutial than the disequilibrium state. The results of a series of exposures of a dosimeter concept fixture in the Denver Mining Research Center radon chamber air presented and discussed.

Jan 1, 1976

By Eugen Gluck, Gus Van Weert, Peter Kondos

"Microwaves have the capability to heat up sulphides, especially clusters of particles of approx. 1 mm. Some sulphides absorb microwaves more readily than others. Molybdenite is especially effective in this regard, possibly due to its flaky nature and/or electrical conductivity. Even where it occurs in low concentrations in a deposit, individual rocks may be ore grade due to the high monetary value of MoS2. Such rocks often result from crushing mined veinlets or stockwork, or are contained in the cutoff grade fraction of ROM. Machine segregation of rocks high in MoS2 by infrared sensors after microwaving could therefore advantageously be used to upgrade lower grade ore between Mine and Mill. This would reduce the size of the latter, and thus its CAPEX and OPEX. Such upgrading could also yield shipping ore for a distant Mill, or extend ore reserves.Barrick Gold Corp. has been supporting the development of MW/IR sulphide sorting for the past three years. The results of MW/IR sorting work on molybdenite and other (pyritic) ore samples from a variety of sources are being presented here.INTRODUCTIONThis paper looks at mechanized, i.e. machine ore sorting technologies currently available and under development, and what conditions would be needed for the potential application of such ore sorting to sulphide mining and milling. Current machine sorting involves no-contact sensing technology for rocks, and signal processing after sensing to activate airblast segregation of certain rocks, normally the smallest mass to keep compressed air costs down.The forerunner of modern sorting is probably magnetic separation, which utilizes an inherent property of certain ores to divert it into mag and non-mags fractions. Radiometric ore sorters, which have been applied successfully for decades in the pre-concentration of uranium ores (Wotruba and Riedel, 2006) initiated modern sorting. In the 90’s, sensor-based machine sorting became a viable means of increasing the overall economic recovery of a resource. This technology became driven by the availability of low cost computing equipment and the concurrent development of algorithms, and by the availability of extremely fast response sensors and air actuators, allowing the sorting equipment to run faster, dropping the cost per tonne. It has been in industrial minerals processing that rock sorting has been most widely adopted, not really surprising. Liberation occurs on a different scale than in the base metal industry. Most industrial minerals are mined from massive deposits, requiring (in the past) no upgrading. Many of these operations now run into product contamination problems, which ore sorting can solve. One illustration: in Finland, a quarry is separating limestone from dolomite at 500 tonnes / hour, with individual rocks weighing up to 15 kg. Many of these industrial minerals operations have stockpiles of earlier discarded below-quality rocks, now being reprocessed with the help of ore sorting. The economics of this are very favourable, going from zero or negative value (stockpiles can not be left when closing the mine) to full product value for at least a portion of the stockpile. This suggests that in the future the economics of overburden sorting could become attractive under the right circumstances and such treatment could well become an integral part of open pit mine development."

Jan 1, 2009

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that contains between 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By Clarence R. Zink

A problem has always existed in deep and fast drilling situations such as coal overburden drilling, or when drilling with a tight annulus, such as 9 7/8" bits and 8 5/8" pipe. This problem is the difficulty experienced by blasthole bit and blasthole drill rig manufacturers to attain large jumps in bit and drill rig productivity through bit and rig design, when drilling in these specific situations. In other drilling situations, these large jumps in productivity have been easily attained.

Jan 1, 1998

Mineral formations, accumulated during technogenic activities greatly influence an economic and ecological situation in the Kola North. On the one hand, the dumps from extraction of mineral resources, tailing ponds of beneficating plants, ash dumps, wastes of metallurgical and mechanical engineering productions destroy the regionÆs environment and require taking certain measures and costs to bury or protect from weathering, oxidation, etc. On the other hand, technogenic mineral formations contain a lot of valuable scarce components. The amount of solid wastes increases annually, causing damage to ecology and economy. Researches conducted in recent years showed a possibility and economic expediency of comprehensive processing of wastes from different enterprises in Murmansk region and their use for production of new competitive commodity output, possessing high consumer properties. Thus, involving mineral wastes from Khibiny apatite deposits into hydrometallurgical industrial processing provides the basis for setting up a large beneficating-metallurgical complex. In this case ores and wastes from other deposits on the Kola Peninsula, containing titanium, rare, rare-earth and other valuable elements, may be involved into processing. Establishing such a complex will allow to organise a deep processing of natural resources, utilise some production wastes, improve ecological security and supply production with competitive output. Expanding the complex implies not only involving new mineral raw material into processing, but mainly deepening raw material processing, maximum utilisation of local natural resources and obtaining a wider variety of prime products.

Jan 1, 2002

A Process for the Flotation of Chrysocolla

Sep 13, 2010

By J. J. Gusek

There are hundreds of passive treatment systems accepting mining influenced water (MIW) throughout the world. Some systems do not perform to design expectations while others, including volunteer systems, have successfully operated relatively unattended for decades. The primary reasons for this situation include the common misconceptions that (1) a “cookbook” approach to design is valid for a wide array of MIW chemistries and site conditions, and (2) low maintenance means “no maintenance.” Passive treatment systems for MIW are typically manmade ecosystems that are designed to handle a specific range of metal loading conditions and MIW geochemistry. Thus, when design conditions are exceeded, the suite of microbial to macroscopic ecosystems may be slow to recover or mature. This should be no surprise to designers. But when a particular system fails, it may be inappropriately attributed to the technology, not the design. This paper presents a standard “phased” design protocol that appears to work and provides examples of sub-par performance of selected passive treatment systems.

Jan 1, 2002

By William J. Campbell

This report describes a Bureau of Mines study undertaken to determine the applications and limitations of solution techniques as a general method of fluorescent X-ray spectrographic analysis. Systematic errors due to variations in particle size, surface preparation, and sample inhomogeneity are eliminated by the use of solutions. The range of applicability of fluorescent X-ray spectrography is increased in two ways: (1) Samples in the form of wire, filings, turnings, etc., can be analyzed as solutions, and (2) samples submitted as solutions can be analyzed as received 0 The lower limit of detectability varies from 0.14 gram per liter for sulfur, atomic number 16, to 0.0015 gram per liter for strontium, atomic number 38. Most elements have limits of detectability between 0.02 and 0.002 gram per liter.

Jan 1, 1959

By Richard Weinstein, Richard Snoby

There are many advantages to upgrading coal with dry jigging technology. The most obvious is the lack of process water, which eliminates the need for fines dewatering and slurry confinement. Dry jigging eliminates the clean coal moisture penalty associated with wet processing. Particulate emissions are virtually nonexistent due to inclusions of fabric dust collectors on all modern dry jig plants. Because of the environmentally friendly nature of dry jig plants, installation permits are often measured in days, not months. There has also been a fundamental advance in dry jigging efficiency. All of these advantages have renewed the coal industry’s interest in dry jigging. But air jigging is not right for every application. There are limitations due to particle size, particle shape, moisture and near gravity content. This article explores the evolution of dry jigging. It reviews parameters important for determining the suitability of dry jigging. It also compares historical performance data as measured by imperfection, against results from modern dry jigging technology. The article also presents data from modern dry jig installations.

Jan 1, 2007

By Elsa Olivetti

Life cycle assessment (LCA) is used increasingly as a tool to provide quantitative metrics of environmental impact and inform early stage materials selection decisions. One common challenge in LCA stems from allocation of burden when multiple adjacent products share some of the same processes. A critical example of this is the partitioning of benefit or burden at product disposition in open-loop recycling scenarios. This work reviews the challenge of allocation and investigates the various methods proposed for allocating end-of-life (EOL) burden. Specifically this work examines whether these methods lead to different results and explores the trends in allocation method bias for or against particular materials classes.

Jan 1, 2010

By T. L. Owen

Since 1993 Cyprus Amax has brought $2.5 billion dollars of greenfield and expansion projects into production, taking it from a mid-sized domestic minerals company into a major international minerals organization. The near simultaneous development of these multiple mineral projects in different locations around the world provided the opportunity for Cyprus Amax to develop a formal project management approach based, in large part, on an outsourcing philosophy. This formal project management system along with its outsourcing philosophy has served the growth agenda of Cyprus Amax extremely well. These preceding factors, coupled with the in-house retention of a core project group that fully understands the breadth of skills and abilities needed to undertake development of multiple large projects successfully, have been the cornerstone of Cyprus Amax’s project development success.

Jan 1, 2000