Search Documents

By John L. Ellenberger, Gabriel S. Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

By Bryan Ulrich

Rroundtable 2009, a Knight Piésold and Co.-hosted roundtable discussion on mine closure and cover design was held at the Red Lion Inn and Casino in Elko, NV on Feb. 12, 2009. Knight Piésold?s Bryan Ulrich and Steve Boyce, as well as Knight Piésold representatives Cynthia Parnow and Corey Conrad from Denver, CO, and Rick Frechette from the Tucson, AZ office were on hand to help facilitate the discussion. The meeting played host to approximately three-dozen attendees from four states. Attendees included personnel from seven mining properties and attendees from corporate offices. The majority of attendees were people directly involved with environmental work on a day-to-day basis. Other attendees were project managers whose jobs involve some level of environmental focus. The purpose of Roundtable 2009 was to exchange ideas and information pertaining to mine closure and cover design associated with almost any aspect of a mining operation. This type of forum provides a less inhibited format for discussion, when compared with traditional conferences and symposia. In the roundtable format, lively discussions are encouraged. This discussion was the fourth in the series of Elko Roundtable events. Previous roundtables pertained to heap leach pad design, construction and operation; design, construction and operation of tailings storage facilities and site-wide water considerations. The initial subtopics for Roundtable 2009 included:

Jan 1, 2009

By W. Pawlak, J. Janiak, C. Rodkiewicz, B. Ignasiak

"There is a general consensus that, in order to widen the utilization of Western Canadian coals, a major effort must be devoted to their transportation, utilization of fines, beneficiation and mining techniques. It is postulated that the concept studied extensively over the last four years at Alberta Research Council (ARC), and based on a combination of hydraulic mining, selective agglomeration with bitumen and/ or heavy oil, pipeline transportation and oil recovery from agglomerates, offers a particularly attractive solution to the problems associated with extraction, beneficiation, transportation and utilization of Western bituminous and subbituminous coals. Results of preliminary experimental work on the feasibility of pipeline agglomeration of metallurgical coal and hydraulic transportation of agglomerates are presented and discussed in the context of conventional agglomeration techniques in stirred tanks. IntroductionAlberta is endowed with enormous reserves of low-sulphur coals which could attract considerable attention of potential customers, but the remote location of this province handicaps its competitiveness on the world market. It is known that Alberta's Cretaceous, particularly metallurgical, coals differ significantly from their Carboniferous counterparts; current R&D work on indigenous coals should continue to expand in order to encourage overseas client s to use these coals more extensively.There is a genera l consensus that, in order to widen the utilization of Western coals, a major effort must be devoted to their transportation, utilization of fines, beneficiation and mining techniques."

Jan 1, 1986

The emergence of China as a global economic power has not been without its birth pangs and the current coal market is testimony to this. Traditionally the coal market has been controlled by mature economies that functioned along balanced lines of supply and demand. The emergence of China and India as major forces in the international market has shifted this balance of power from mature economies to the developing economies of China and India. Of late Chinese Central Government policy has caused wide swings in the supply of Chinese coking coal and thermal coal to the international Asian markets. This has resulted in huge increases in demand for coal from producers in Australia, Canada, Indonesia, USA and Russia. Additionally since the late 1990s the liberalised Chinese economy has been growing by between nine to 12 per cent per annum. The corresponding rise in the standard of living of their 1.4 billion people has resulted in a strong demand for raw materials, initially met by domestic production and more recently met by the importation of raw materials including iron ore, oil, coking coal and thermal coal. Commensurate with this growth in China has been the emergence of India (pop one billion) as another major developing economy in the region. Whilst the Indian standard of living is lower than that of the Chinese, this subcontinent still has some 300 million people with middle class consumption demands. India is a major importer of oil, coking coal and thermal coal. It exports iron ore to China with growth parallel to China (seven to nine per cent per annum). These combined new demands from India and China have put unprecedented pressure on the global supply of coking and thermal coals. These pressures are reflected in the current world spot prices for coking and thermal coals which are at historically high levels. Whilst current demand from China and India is high it is anticipated that new projects will partially satisfy this increasing demand. Expectations are that overall thermal and coking coal prices will rise steadily. This paper seeks to identify the potential effects of Chinese and Indian economic growth on the international markets for coal.

Jan 1, 2004

By John R. Wolosick

MACROPILES are defined as ultra-high-capacity micropiles, with working loads in excess of 250 tons. The piles are typically 9-5/8 to 24 inch (244 to 610 mm) outside diameter. They are drilled and grouted in place, with either large diameter steel bars and/or steel pipe reinforcement. The piles are typically tested to twice the working load. Piles with working capacities of up to 500 tons and tested to 1000 tons have been installed. The paper discusses MACROPILE design philosophy, construction techniques, and two case histories where this innovative foundation system has been installed. Macropiles are descended from micropile technology pioneered in the early 1950s by Fernando Lizzi of Italy.

Jan 1, 2006

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008

By Qingwei Wang

This study focused on acidic wastewater from producing sulfuric acid system in zinc smelter containing mercury 21.48mg/L, zinc 55.85mg/L, lead 38.50mg/L, copper 1.68mg/L, cadmium 10.25mg/L, As 29.86mg/L treated by biologics. The factors of pH value, the ratio of biologics to mercury, complexing time, hydrolytic time and temperature were studied in this paper. Experimental results indicated that at pH value 10, quantity of biologics to mercury ratio was 16, complexing time 30min, hydrolyzation time 20min, temperature at 40?, concentration of mercury in treated water was removed to 22.15µg/L. At same time heavy metals such as Zn, Pb, Cu, Cd, As was removed by biologics, the remained concentration in treated water was Zn 0.53mg/L, Pb 0.12mg/L, Cu 0.01mg/L, Cd low to 0.01mg/L and As 0.023mg/L. According to EDAX analysis, mercury content in complexing sediment reached 28.49% easily to recycle as raw material and low concentration of heavy metals in hydrolytic sediment easily to dispose and treat.

Jan 1, 2009

By P. W. Godbehere

"INTRODUCTIONMagnetic mill linings have been developed from an invention by Mr. Bertil Brandt, the originator of the Skega rubber lining. The OREBED magnetic mill lining is a concept in which rubber covered strontium ferrite permanent magnets are arranged on the inside wall of a mill shell so that they attract magnetically susceptible material be it ore, media or tramp, to form a protective layer over the magnets and to serve as an operating surface with indefinite life.Noranda Mines Ltd. through its associate Norcast Division of Noranda Metal Industries formed a joint venture with the inventors to market magnetic mill linings in North America. For the past twelve months trials have been undertaken in conjunction with Orebed Inc. to test and develop these linings for grinding mill applications at the Horne Concentrator. Two independent milling circuits are currently being operated, one treating a siliceous gold ore and the other a copper slag.This paper presents the results of the magnetic lining test programme to date."

Jan 1, 1983

By B M. Washington, R R. Lovel, G J. Sparrow, M J. Fisher-White

"Work in CSIRO with several Australian ores has shown that?by heating a high-phosphorus goethitic iron ore and then leaching with caustic or acid, the phosphorus levels in the ore can be lowered to a commercially acceptable value of around 0.08 weight per cent phosphorus (P). With increasing heating temperatures up to 1300¦C, the extent of phosphorus removal increased. This is considered to be associated with mineralogical changes in the iron oxide phases in the ore during the heating.Little phosphorus was removed from four high-phosphorus goethitic iron ores containing 0.12 - 0.16 weight per cent P in leaches with boiling water. However, leaches with sulfuric acid removed ten to 20 weight per cent of the phosphorus and leaching with sodium hydroxide removed even more phosphorus to produce leach products containing between 0.08 and 0.12 weight per cent P from three of the ores.After heating at 300¦C, leaches at a low pulp density of 0.5 weight per cent solids with 1 - 5 M NaOH and 0.1 - 1 M H2SO4 gave leach products with 0.06 - 0.09 weight per cent P. The lixiviant concentration required and extent of phosphorus removal depended on the ore. At a higher pulp density of 25 weight per cent solids, leach residues with between 0.07 - 0.14 weight per cent P were obtained.More phosphorus was removed from ores heated at 900¦C. Leaches at both the low and high pulp densities, with 1 - 5 M NaOH and 0.1 - 1 M H2SO4, gave leach products with 0.05 - 0.09 weight per cent P. However, the lowest phosphorus levels were obtained after heating the ores at 1200 or 1300¦C and leaching with 1 M NaOH or 0.1 M H2SO4. Leach residues with 0.02 - 0.06 weight per cent P were obtained, even from leaches at the higher pulp density of 25 weight per cent solids. Leaching tests on heated samples under heap leaching conditions at ambient temperatures have shown that phosphorus levels can be reduced to similar levels to that achieved in an agitation leach within ten days.CITATION:Fisher-White, M J, Lovel, R R, Sparrow, G J and Washington, B M, 2013. Effect of temperature on removal of phosphorus from Australian Goethitic iron ores, in Proceedings Iron Ore 2013, pp 373-380 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By Steven C. Borell

For more than a decade, changes have occurred each year that have improved the regulatory and business climate for mining in Alaska. These changes have taken place during Republican and Democratic governorships as well as when the state House of Representatives and Senate were controlled by either party. During some years, the changes have been relatively minor. In others, including the 2003 legislative session, the changes could only be characterized as massive. These improvements have encouraged exploration. This, in turn, has resulted in some major new discoveries. But Alaska is essentially unexplored and tremendous opportunities remain.

Jan 1, 2004

By K C. Williams, A W. Roberts, J D. Prigge

For stockpile design, the flowability and structural interfaces are critically dependant on the stress conditions throughout the pile. Historically, the predictive methodologies for stress determination have been too conservative, which adds inefficiency to the stockpile reclaim interface selections, especially for live reclaim stockpile systems. In addition, accurate pressure profiling throughout stockpile is essential to correctly design the stockpile support structures, which are buried within the stockpile. Such buried structures include trestle legs or columns to support load-out conveyors or the roof of bulk storage sheds. Improved methodologies with respect to the development of the hoop stress condition which exists in material ædrawn-downÆ within the stockpile has been developed. This hoop stress approach has significantly improved the live capacity prediction to over 90 per cent accuracy and improved rathole structure prediction within live reclaim stockpiles. Additionally the methodologies in estimating the vertical and circumferential stress variation acting on buried stockpile structures have been significantly progressed, with experimental testing shown good agreement with the theory.CITATION:Williams, K C, Roberts, A W and Prigge, J D, 2013. Recent developments in stress analysis and live reclaim prediction within iron ore stockpiles, in Proceedings Iron Ore 2013 , pp 501-510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By J. E. Rourke, O&apos

A wide variety of techniques and equipment are available for coring soft or poorly consolidated geological material. This report presents a comprehensive literature review and evaluation of these techniques and equipment. A potential user will find guidelines in this report to assist him in selecting sampling equipment. A bar chart shows what samplers have been used under what geological conditions, and gives the specific literature references. Two matrices rate the present techniques and equipment with respect to reported success for sampling specific materials, and with respect to several performance characteristics including complexity of use and core quality. These matrices are supplemented with tables of typical sampling equipment. and program costs. Near-term future developments are seen primarily in improved training of drillers, and in instrumenting the drilling operation to provide objective data on drilling characteristics. An extensive annotated bibliography, a catalogue of equipment suppliers including specifications and cost ranges, and a list of manufacturers and distributors are appended to the report.

Jan 1, 1978

By Thomas J. Kuli, Tim Rape

When a fan or blower breaks down or becomes worn, customers have two choices. They can replace it or they can have it repaired. In the past, replacement was the preferred option, especially when the equipment was severely damaged or worn. Now, however, customers are discovering the benefits of repairing or rebuilding. Even when the cost of repair is more than 60 percent of the cost of a new fan, customers are choosing the repair option. The cost savings can range from 20 percent to 80 percent. In many cases, the quality of the repaired part or component will exceed the quality of the original. This is because repair engineers have an advantage over the original designers. They can see how the existing fan performed — or failed to perform — in a specific application.

Jan 1, 2005

By M. L. Tucker, William H. Langer

Many countries, provinces, territories and states in the European Union, Australia, Canada, the United States and elsewhere have begun implementing sustainability programs. Most of those programs, however, stop short of sustainable management of aggregate resources. Sustainable practices do not always have to be conducted under the title of sustainability. This case study describes how Lafarge implemented the principles of sustainability even though there was an absence of existing local government policies or procedures addressing sustainable resource management. Jefferson County is one of three counties in the six-county Denver, CO, region that has potentially available sources of crushed stone. Crushed stone comprises 30percent of the aggregate produced in the area. And it plays a major role in regional aggregate resource needs. Jefferson County is home to four of the five crushed stone operations in the Denver region. Lafarge operates one of those four quarries.

Jan 1, 2004

By Barry C. Slocombe

The development of new ports, extensions of existing facilities and reclamation of former docks will involve consideration of a variety of geotechnical problems. This paper presents data including instrumentation of structures from three UK projects involving vibro techniques to provide economic engineering solution.

Jan 1, 2008

The southern portion of the Swan Coastal Plain, a geomorphological element formed since late Tertiary times, contains commercially exploitable accumulations of ilmenite, zircon, rutile and monazite associated with a series of raised shorelines. The location of the deposits is controlled by a locally outcropping Archaen granite/ granulite complex and a sea current pattern determined by local geography and a prevailing wind direction. A progression from medium to high titanium ilmenite is evident parallelled by progressive leucoxenisation as the age of the deposits increases. Variations in trace element content accompany this process. Circulating groundwater has caused vertical mineralogical variations within individual deposits and by precipitation of iron has formed layers of hardpan.The Geographe Bay deposits are of important economic significance.INTRODUCTIONObservations made during the course of a brief survey of the southern portion of the Swan Coastal Plain provide an outline of the geology and mineralogy of the mineral sand deposits of the area. This preliminary study will require considerable modification in the light of more detailed work in the future.REGIONAL GEOLOGYThe Geographe Bay area is situated in the south-west corner of Western Australia between longitudes 115° O'W. and 116° O'W. and latitudes 33° 15'S. and 33° 45'S.The general geology of the area is shown in Fig. 1 where the control of the physiography exercised by the Cape Leeuwin-Cape Naturaliste basement ridge is readily apparent. Between this ridge and the Precambrian east of the Darling fault lies the southern part of the Perth basin which contains outcropping Jurassic to Recent sediments and lavas (McWhae, et al., 1958).The Leeuwin-Naturaliste ridge is the exposed portion of L Assistant Production Managcr. Laporte Titanium (Aust.) Ltd.

Jan 1, 1964

By S. G. Gibbs, A. B. Neely

Jan 1, 1967

By Penrose E. K

With the exception of occasional periods, when up to 80% of oxidized ore was treated, the G.M.K. plant treated all sulphide ore until October, 1939. The treatment was, briefly, as follows:The ore was ground to approximately 17% plus 200 mesh Tyler and agitated in cyanide solution, after straking. After agitation, the pulp passed through two stages of counter-current decantation washing in Dorr thickeners and was filtered once, to complete the precyanidation stage.The precyanide filter cake was repulped with flotation circuit solution and floated in a Denver Sub A flotation machine, consisting of twelve cells. The concentrates were roasted, cyanided and filtered four times before disposal to the' dam. The flotation tailings were thickened to conserve water and pumped away to a separate dam.The average results of flotation operations for the six months before October, 1939, are shown in Table 1.

Jan 1, 1942

By A. Asadi

Subsidence phenomenon as an unwanted consequence of underground mining can cause problems for environment and surface structures in mine area. Surface subsidence prediction for inclined and steep seams has been given less attention than horizontal seams due to the difficulties involved in the extraction of such coal-seams. This paper introduces a new profile function method for prediction of surface subsidence due to inclined coal-seam mining. The results of calculation with the new function indicate that the predicted value has good agreement with the measured data. Keywords: subsidence; coalmining; caving mining methods; longwall mining; profile function.

Jan 1, 2005

By A. Raja, C. C. Harris

Apparatus for maintaining constant — but adjustable — pulp level and rate of froth removal are described. The results of preliminary experiments into the effect of scraping speed on the rate of solid and liquid recovery with a semi-batch system are presented. Glass spheres restricted to a narrow size range is the solid under investigation. Graphical methods for estimating the mass of recoverable material and the zero error are given. The semi-batch procedure1 is extensively used in laboratory flotation testing, though the method is subject to variability of moderate severity. Raffinot2 concluded from a statistical study of the difference between replicate tests, that the ptincipal source of errot was the test itself and not sampling or chemical analysis. These differences can be ascribed principally to changes in pulp volume and reagent concentration, and uncontrolled rate and depth of scraping. Semi-batch testing has been criticized1 on these grounds as a means of investigating flotation kinetics. This paper discusses and describes modifications to laboratory flotation equipment which reduce the number of manual operations and lead to improved control. Kinetic studies were the primary reason for developing the apparatus described. It should, however be a useful aid in normal flotation testing. Some preliminary results of experiments are presented.

Jan 1, 1967