Search Documents

Updraft sintering of lead concentrates was introduced at Port Pirie in 1955 and since that time a considerable amount of investigational work has been carried out in the laboratory and on the plant with the objective of improving both the understanding of the process and its practical application.From this work it is now possible to predict trends in design and operation, which should result in capital savings and increased efficiency of future updraught plants.INTRODUCTIONOver the last 70 years a remarkable advance has been made in the method of preparing lead concentrates for smelting in the Port Pide blast furnaces of The Broken Hill Associated Smelters Pty. Ltd. (RH.A.S.). Beginning in 1889 with heap roasting, the process progressed to Ropp roasters and Huntington-Heberlein pots in various combinations, then to multiple small Dwight Lloyd (D.L.) downdraught machines. In 1940 two large 10 ft by 50 ft D.L. downdraught machines were installed, and finally in 1955 updraught sintering was ,introduced with the installation of the present 10 ft by 99 ft sinter machine.At the time this last machine was built it was the first unit of its type and thus, of necessity, an experimental machine. During the eight years it has been operating a considerable amount of investigational work on sintering has been carried out both on the plant and in the laboratory.It is now felt that sufficient information is on hand to predict at least tentatively, some of the future developments in lead sintering, whereby both the quality of the sinter and the rate of production may be improved. This will result in a considerable reduction in smelting costs.

Jan 1, 1964

Two small coral islands in the Pacific Ocean, situated close under the equator, and formerly classed among the Line Islands, have, during the last three or four years risen into prominence owing to the valuable deposits of phosphate of lime discovered on them.The deposits of Ocean and Pleasant Islands are under the control of the Pacific Islands Company (1902) Limited, of London and, Sydney, and the high grade of the phosphate, together with the exceptionally favourable facilities for mining this mineral, of which there are several millions of tons on these islands, give this company advantages which enable them to command the Australian and New Zealand markets, and also to make large contracts with Japan and other countries. Both islands, as far as surface indications are concerned, are entirely constructed of coral, with phosphate on the top from the highest points to the present sea level, there being no sign of volcanic rocks, with the exception of a few pieces of drift pumice on the coast.Banaba (Paanopa according to. the Admiralty charts), also known as Ocean Island, was discovered in 1804. It is situated in lat. 0° 52" S. and long. 169P 3[)" E.

Jan 1, 1904

By Matters, R T, Coldham, Slee, J C, R J, Wallman

The Committee desires to thank the managers of the various mines along the line of lode for their hearty co-operation in its labours. It would also extend thanks to Messrs J C Moulden, Howchin, Twelvetrees, and the West Australian Geological Surveyfor various information; to Messrs J G Dreyer, S Pope, T Read, P Moncrieff, R Williams, and W J Rose for analyses; and to a number of local gentlemen for advice and help. Professor Skeats, of Melbourne University, gave much valued assistance in petrology, and Mr Herbert Lavers kindly undertook the study of the garnets.INTRODUCTIONThe famous Broken Hill lode is situated in a low range of hills, the Barrier Ranges, near the western border of New South Wales. It has been worked since 1884-fust for silver, then for silver and lead, and at present for lead, silver, and zinc...

Jan 1, 1910

By Greenwood J. N

This work was commenced at a time when information on the manufacture of cemented tungsten carbide was urgently needed in Australia. Much information of a general type has been published, but many of the details of the processes used are still undisclosed. The aim of this research was to determine a satisfactory way in which cemented tungsten carbide could, be made, and to investigate the problems which are associated with the process. As the work proceeded, its ramifications grew continually, and it was necessary to limit the possible lines of investigation. After much experimental work, a 9% cobalt-tungsten carbide alloy was developed which had satisfactory properties when used as a cutting tip. The effect of certain variables on the properties of this particular alloy was investigated.The tungsten carbide was prepared in stages from King Island scheelite concentrates under strict laboratory control, whilst the cobalt (1) used was made from cobalt oxide prepared from crude cobalt oxide obtained from Eisdon.In order to clarify the detailed experimental work, a brief summary of the method used for the preparation of cemented tungsten carbide follows.Tungsten carbide and cobalt are prepared in a very finely powdered state, and are then thor,oughly mixed by a ball milling operation. The resultant mixture is pressed in a suitably shaped die into small compacts which are subsequently '''presintered,'' i.e., heated' in hydrogen between 800°C. and 1000°C. The final sintering is carried out in hydrogen between 1,400°C.and 1,600°C. for about half an hour. These "alloys" may contain from 3 to 13% cobalt, depending on the particular properties required of them.PREPARATION OF MATERIALSThe tungsten oxide prepared as described by Smithells (2) was extremely finely divided, and after a few hours' grinding in a ball mill, the powder consisted of material below 10 microns iJ;l size. The oxide was reduced to tungsten metal with hydrogen in a tube furnace. The reduction was carried out at 800-900° C., a rapid flow of hydrogen being maintained in order to remove the water vapour' formed as a result of the reactions:

Jan 1, 1942

By Graeme McWhirter

This paper discusses the Installation of a Vibwall for the Cardiff Bay Barrage Project Wales, UK, by Kvaerner Cementation Foundations. Only the second use of the technique in the UK the wall was successfully placed to a depth in excess of 20 metres, in unique and challenging conditions. The installation of the Vibwall was a technical success, but not a financial one. The use of the technique was at its "limits" and this paper recommends some of the controls essential in the carrying out of such work in the future.

Jan 1, 2000

By Ning Shi

This paper suggests an alternative design approach for an innovative shovel dipper, for use in ground conditions where cutting of virgin ground rather than scooping of blasted material is required. Not only does the new design have an optimized dimension ratio (width:height:depth) and attachment arrangement (angle, position), but also a non-linear pro¯le in 2D and 3D. The approach is based on the simulation of a shovel's duty cycle to verify a pilot dipper model. In order to achieve a realistic simulation that could be used to evaluate a dipper design, the model is e®ectively a descriptor of actual shovel activity under soft ground conditions. The shovel geometry, motion and operation, with an emphasis on digging and dumping kinematics and dynamics are the principal elements of the simulation. The simulation considers a fresh face location, repeating tucking, digging and dumping swing motions within the geometric range of the machine, ending when no more face material remaining within reach without re- positioning. The simulation yields digging force, friction force, trajectory, ¯ll time, ¯ll factor, etc, which may be integrated into two basic considerations: power draw (output) and volume delivered (production), as indicators of dipper performance. The simulation has been used as a tool to modify an existing dipper design, prior to looping further simulation cycles. Ultimately, an optimized or totally-new-concept shape is realized. A prototype dipper as a fractional scale model will be built to verity the performance under actual mining conditions.

May 1, 2004

By M. H. Moys, J. A. Finch, A. R. Laplante

"A detailed review of ball milling circuit control practices in industry has been carried out. Based on fundamental process performance objectives, a standard system for base-level control of most ball mill installations is presented. This system is simple, inexpensive, and provides the major economic benefits available from contemporary automatic control technology.Value Analysis of Grinding OperationsValue analysis (or engineering, or management), originally developed by Lawrence D. Miles of the General Electric Company (1), focuses on the identification of value (product or process worth versus cost) and provides a systematic procedure for its improvement. A recent research and development project involving the application of the principles of value engineering to grinding operations has provided a basic technoeconomic model of grinding processes (2). The functional objectives of the ball milling process and the means to achieve value based grinding circuit control originate from this study.The Need for Grinding Circuit ControlThe economic effectiveness of a process is determined by the quality or value of the product and the related processing costs. If the inputs (both the raw feed and the applied processing work) are absolutely constant, the product characteristics and the process efficiency will be determined only by the engineering design. The need for and degree of process control is therefore determined by the nature of variations or upsets in the process inputs, and the extent to which these effect product value and operating costs."

Jan 1, 1988

By R. T. Stain

Integrity testing of deep foundations is now common practice in Europe, indeed in the City of London such testing is a contractural requirement on every site. This paper is in two parts: Part 1 describes the most commonly used test methods and their applications. Part 2 presents a case history where both of the above techniques were used.

Jan 1, 1987

By Richard Rice

TURBO blowers for blast-furnace blowing have now been in use for some years, and a review of the experience gained and the present state of progress may be interesting. FIG. 1.-STEAM TURBINE DIRECT CONNECTED TO AIR COMPRESSOR. The first blast-furnace blowing engine of this type to be installed in America was built by the General Electric Co. and is installed at the oxford Furnace of the Empire Iron & Steel Co. This machine was put into operation March 8, 191.0. A duplicate unit is situated at the furnace of the Northern Iron Co. at Port Henry, N. Y., which unit was put into opera ion June 30, 1910 (Fig. 1).

Jan 5, 1914

By Paul J. Sabatini, Yazen A. Khasawneh

"A Demag CC1800 crawler crane was partially erected on crane mats adjacent to a seawall when settlements near a corner of the crane mat area were observed to be slightly larger than previously assessed. A ground improvement program including installation of dry soil cement mix (DSM) piers was implemented to improve soil bearing capacity. Due to near-surface obstructions, only 75 percent of the DSM piers were installed to the design depth. Because of the partial installation of the DSM piers, an evaluation of the crane pad stability and the effect of the crane loading on the stability of an adjacent 10-ft high concrete seawall, which was believed to have limited (if any) reserve capacity, was required. A two-dimensional finite element model was developed to evaluate the responses of the partially improved ground and the sea wall to the loads imposed by the crane. Geotechnical site investigation and laboratory testing programs were performed to better define the subsurface conditions near the area where settlements occurred and to provide the required mechanical parameters for the soil constitutive model. Analysis results indicate that total and differential settlements of the crane pad and the increase in load on the seawall were tolerable provided limited excavation and replacement of weak dredged soils outside the DSM area would be implemented.INTRODUCTION & BACKGROUNDA Demag CC1800 was erected on 8 ft × 16 ft crane lattice mats at about 12 ft from an existing seawall. Approximately 3.5 in. of subsidence was observed at one corner of the crane mats, while the crane was partially erected and stationary. The approximate location of the crane mats with respect to the existing seawall when the subsidence occurred is shown on Fig. 1.The seawall consists of a reinforced concrete wall connected by reinforced concrete bents to a composite section of sheet pile wall; the total depth of the seawall is about 29 ft. The bents are spaced at about 20’4” and supported by five piles at each bent location. The composite sheet pile consists of concrete and a sheet pile section with a reinforced concrete wale section. The retaining wall is about 10 ft in height and is supported at three levels. The first support level comprises a 2-½” diameter steel rod near the top of the wall spaced at 40’8” the second and third level supports comprise 1-½” diameter steel rods spaced at about 5’6”. The second level support is inclined at about 10 degrees below horizontal and the third level support is oriented horizontally through the wall footing. A schematic of the seawall section is shown on Fig. 2.A geotechnical site investigation was implemented soon after the subsidence was observed. The program included advancing four borings to a depth ranging from 16 ft below ground surface (bgs) to about 30 ft bgs. In general, the investigation showed sandy material (likely fill that was used behind the retaining wall) from the ground surface in two borings located immediately behind the retaining wall. The other two borings furthest from the retaining wall showed very soft to soft clay (possibly dredged material) from the ground surface to a depth of about 10 ft bgs. Based on this information, the ultimate bearing capacity of the subsoils was estimated to range from 1,200 to 2,000 pounds per square feet (psf). From the anticipated crane loading (weight of the crane and loading lifts), a minimum allowable bearing capacity of about 1,500 psf would be required for safe operation. To achieve the required bearing capacity a ground improvement program was selected and implemented."

Jan 1, 2017

By Walter Valery, Peter Radziszewski

"The NewCrest Cadia operation boasts the largest SAG mill commissioned last June 1998. A request was made to shed some more light on possible SAG mill charge behaviour. Three different software were used to simulate SAG mill charge behaviour:Mishra/Rajamanis MillSoft DEM charge motion program, Radziszewskis agglomerated DEM charge motion program and Powell/Nuricks MillTraj outer trajectories program. The contexts simulated are: 20/30 % charge volume, 65/75/85 % critical speed using the Hi-Lo lifter configuration specified for the mill as well as a Hi-Lo 60 degre lifter face configuration. Further, lifter interval was also studied to determine the effect on power draft. Power predictions are compared with those obtained during the commissioning period.INTRODUCTIONThe NewCrest Cadia operation is located outside of Orange, New South Wales, Australia. With proven reserves of 190 million tonnes at a grade of 0.75 g/t Au, the mill was designed to process 17 Mtpa (2065 tph) of ore with an 86% copper and 73% gold recovery. The grinding circuit (Fig. 1, Table I) boasts the largest SAG mill (Fig. 2) and was commissioned last June 1998."

Jan 1, 1999

Sluice box operating practices in Papua New Guinea (PNG), and published work on sluice boxes are briefly reviewed. Some recent work on sediment entrainment mechanisms occurring in sluice boxes have also been described. In the light of this information, some drawbacks in the commonly adopted sluice box operating practices in PNG, and ways of overcoming them, are also highlighted.

Jan 1, 1991

The Hill 50 Gold Mine is situated at Boogardie, 3 miles on a bearing of 295 degrees from; Mount Magnet township. Mount Magnet lies 300 miles north-north-east of Perth, Western Australia (Fig. 1).The older workings of the mine may be identified with those of Sirdar, Gold Mining Lease 696M The Sirdar had been worked before 1902 though no records remain, and irom 1903 to 1912 about a thousana tons at a grade of 6' 2 dwt. was extracted annually; by the end of 1918 6,225 oz. of gold had been obtained from the milling of 17,852 tons of ore. In view of these yields, and the length and width of the lode, this mine was early recognized as one of the most promising in the district. From 1919 to 1924 the ground,including G.M.L. 1282M, was held as Mt. Zion G.M.L. 1183M.The Hill 50 Gold Mine N.L. company took up the workings as Hill 50 G.M.L. 1282M in 1934 and have continued operations to the date of writing. To the end of 1956 the Hill 50 Gold Mine had yielded 982,106 tons of ore for a return of 448,'602 fine oz. of gold.The mine has been described by: J utson (1915), Feldtmann (1920), Johnson (1949), and Finucane (1953). Finucane (1953) details the mine structure to a depth of 414 ft. The author was able to examine the mine to a depth of 1305 ft. Detailed main level mapping to the 1060 level and a detailed surface examination have revealed aspects of the structure which were previously obscure.

Jan 1, 1960

[ ]

Jan 1, 2008

By P. J. Hancox

Heavy mineral deposits have been known from Liberia since the1950s from both river and beach placers. The heavy mineral content of beach sands ranges between 28?62% and the suite includes ilmenite, rutile, zircon and magnetite. These occur together with kyanite, sillimanite, staurolite and garnet. The average ilmenite content is 82% with minor zircon (11%), rutile (6%) and monazite (1%). The ilmenite is, however, of poor quality with haematite intergrowths and a titanium content ranging from10?42.4% (average ±25% TiO2). The amounts of rutile and zircon, while of suitable quality, have also previously been deemed too low for economic exploitation.

Jan 1, 2000

When perusing articles which treat of mining geology, and when talking with miners on the field, one is at times unable to follow the exact thoughts intended to be expressed, owing to the introduction of occasional technical words, the meanings of which are not thoroughly understood either by the speaker or by the hearer, or possibly by both and laymen at times accuse their technical brethren of attempting to confuse them by employing unusual words in their conversations and writings. Technical words are necessary adjuncts to all arts and sciences. They creep into our language, frequently unnoticed by those who employ them, as being more concise and convenient than longer sentences to explain frequently recurring expressions. In many cases these words give the finest shades of meaning, such as aglomerate and congzomerate, but in others they are extremely ambiguous, for instance black sand, which in some places means ilmenite, in others, chromite, tourmaline, cassiterite, in fact, any black mineral occurring in the form of sand. Then, again, much confusion is cansed by the same rock or mineral having different names, e.g, jlu01'spa'i', which is known as cand, cann, cauk, kawk, blue-John, Derbyshire spar, &c. The multiplicity of local names is of course chiefly found among the more common minerals, which are widely distributed some people have a propensity for using words the meanings of which they understand as little as' they do how to pronounce them. We have heard such persons speak 'of vughs as "bugs," and oxides as "ox hides," and to show that there was no mistake in their intentions, we have seen these and other words written in the same way as they were pronounced. Then, again, some persons, relying more on examples than definitions, get a very vague idea as to what the true meaning of a term may be the word dimite is an example in point, which we have frequently heard applied to any dyke rock that the miner was unable to recognise as granite in fact, he uses the word in a general sense, just as the field geologist provisionally employs the word " greenstone " for certain rocks, until he has an opportunity of thoroughly investigating their character.

Upgrading of a Flow Sheet Selection PC Algorithm for Refractory Concentrates Treatment

Sep 13, 2010

The mineral composition and microtextures of a cubanite-rich sulphide ore are described and cubanite breakdown textures are illustrated. The occurrence of cubanite in macroscopic dimensions is featured.The origin of the ore is tentatively related to a composite ore fluid arising initially from an ultramalic source and extracting some metal components from an older granite mass along the margin of which the serpentine was emplaced. Some alternative possibilities as to origin are also mentioned.

Jan 1, 1969

Jan 1, 1970

By W Farnworth

The Huntly West Mine has undergone significant changes in the last two years, which will affect the remainder of the mine's life. The paper describes the evolvement of plans and an overview of the technical considerations made in planning for and implementing the first New Zealand longwall operation. The technical investigations involve the longwall equipment, exploration, ventilation and strata control. The focus on these areas was to ensure that unacceptable project risks were addressed. Implementation of longwall mining at West Mine is planned in three phases, Development, Panel One extraction trial, and Full Longwall operation.   At present the development phase is complete, longwall installation is in progress and production start-up is planned for the end of August, 1991.

Jan 1, 1991