Search Documents

By Dennis Dolinar

Improperly designed support systems have led to unplanned roof falls in longwall tailgates. To prevent such falls requires appropriate support and adequately designed support systems. The National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. To design the support system with this methodology requires a quantitative assessment of the ground and support interaction, which is developed from instrumented test sites installed in longwall tailgates. To compliment and expand the field data results and to optimize the support design, numerical modeling is also conducted. The models are calibrated from the test site data. In the present study, data was obtained from a longwall tailgate in the Illinois basin. The test site was located in the Herrin No. 6 coal seam at a depth of 500 ft. At the site, the immediate roof was a weak shale overlain by a competent limestone. Above the limestone, sandstone formed the intermediate roof. The floor consisted of a weak underclay. In the study, the performance and interaction with the surrounding rock mass of two different standing supports, an engineered crib and a conventional 4-point wood crib were monitored. The two cribs have similar load-displacement characteristics at least through 6 in of displacement. Beyond 6 in, the engineered crib becomes unstable and begins to strain soften and shed load. The measurements and developed ground reaction curves indicated that the tailgate at the mine was a low convergence environment until well inby the face. Because the convergence was well below their capacity, both supports provide more than adequate levels of support to the tailgate. Significant convergence and support loading did not occur until 90 to 100 ft inby the face. The results of this study were also compared with results from similar studies conducted in the Pittsburgh seam to further advance the development of the ?ground reaction curve? based support system design.

Jan 1, 2009

By Mark G. Lafontaine

Underground 802.11 wireless communications has become widely adopted for automation and communication purposes but maximizing the wireless signal presents many obstacles given the harsh environment as well as the presence of materials and conditions that can reduce signal propagation. Changes in elevations and curvatures in ramp to drift transitions also affect the wireless signal. Based on the requirements of wireless applications such as voice, data, or location tracking, the wireless site survey is the key tool for measuring and predicting signal strength and signal-to-noise ratio. These readings help determine the maximum distance between access points in order to sustain an overlapping wireless signal where required. This paper describes the methodology and tools used for measuring 802.11 wireless signal strength in an underground mine environment in Northern Ontario. The physical characteristics of the mine and the actual recorded wireless signal data will be presented in order for the audience to gain an understanding of the factors that affect signal throughput. Antenna selection used for the site survey will also be discussed as it played a key role in propagating the wireless signal.

May 1, 2013

By E. G. Baglin

As part of an effort to decrease U.S. dependence on imports of critical and strategic metals, the Bureau of Mines investigated three leaching methods for extracting the base metals and recovering platinum-group metals (PGM) from matte prepared from Stillwater Complex flotation concentrates. Because of a limited supply of natural material, synthetic matte of composition similar to matte prepared from natural concentrates was used to devise the extraction sequences. The validity of the sequences was verified with matte prepared from Stillwater concentrates. In two-stage matte leaching, first-stage H2S04 leaching extracted 99 pct of the nickel and iron from the matte but negligible amounts of copper and PGM. Second-stage oxidative leaching with Fe2(S04)3 or FeC13 solubilized more than 98 pct of the copper and no precious metals. Sequential leaching, in which acid and oxidizing lixiviants were added sequentially to the matte without an intervening filtration step, extracted 99 pct of the Fe, Ni, and Cu. A roasting-leaching technique, in which the residue from first-stage leaching was roasted between 360° and 500° C before a second leaching with H2S04, solubilized 98 pct of the copper. The three leaching methods yielded high-grade PGM residues containing more than 98 pct of the PGM in the matte.

Jan 1, 1982

By Donald P. Tuchman, Justin R. Patts, Emanuele G. Cauda, Andrew B. Cecala, Elaine N. Rubinstein

Video techniques for monitoring exposure, such as NIOSH’s “Helmet-CAM,” employ both real-time dust monitors and mobile video cameras to assess workers’ respirable dust exposures. Many real-time personally worn dust monitors utilize light scattering sensing elements, which are subject to measurement biases as a function of dust type (size, composition, shape factor) and environmental conditions such as relative humidity. These biased and inaccurate dust measurements impair the monitor’s ability to properly represent actual respirable dust concentrations. In the testing described, instrument mass concentration data was collected using three different types of commonly used commercial off-the-shelf personal dust monitors and compared to a reference standard. This testing was performed in a calm air (Marple) dust chamber in which three units of each make and model (for a total of nine monitors) were used for each test. Equivalency factors (EF, a multiplier to match the Thermo TEOM 1400a reference instrument) ranged between 0.746 and 1.879 across all dusts and environmental conditions tested, and between 0.821 and 1.519 on the ISO test dust.

By Donald P. Tuchman, Justin R. Patts, Emanuele G. Cauda, Andrew B. Cecala, Elaine N. Rubinstein

Video techniques for monitoring exposure, such as NIOSH’s “Helmet-CAM,” employ both real-time dust monitors and mobile video cameras to assess workers’ respirable dust exposures. Many real-time personally worn dust monitors utilize light scattering sensing elements, which are subject to measurement biases as a function of dust type (size, composition, shape factor) and environmental conditions such as relative humidity. These biased and inaccurate dust measurements impair the monitor’s ability to properly represent actual respirable dust concentrations. In the testing described, instrument mass concentration data was collected using three different types of commonly used commercial off-the-shelf personal dust monitors and compared to a reference standard. This testing was performed in a calm air (Marple) dust chamber in which three units of each make and model (for a total of nine monitors) were used for each test. Equivalency factors (EF, a multiplier to match the Thermo TEOM 1400a reference instrument) ranged between 0.746 and 1.879 across all dusts and environmental conditions tested, and between 0.821 and 1.519 on the ISO test dust.

Trans. No. Place Date Vol. Page 1. Wilkes-Barre Pa......May.71 1 3 2. Bethlehem, Pa.........Aug., '71 I 10 3. Troy, N.Y............Nov..: 71 1 13 4. Philadelphia, Pa........Feb., 72.. 1 17 5. New York. N. Y.*......May, '72.. 1 20 6. Pittsburgh. Pa.........Oct..' 72.. 1 25 7. Boston, Mesa..........Feb., '73.. 1 28 8. Philadelhia, Pa.*......May, '73.. 2 3 9. Easton, is............Oct..' 73.. 2 7 10. New York, N. Y.......Feb..' 74 . . 2 11 11. St. Louie. Mo.*........May,' 74 . . 3 3 12. Hazleton, Pa...........Oct., '74.. 3 8 13. New Haven Conn......Feb., '75.. 3 15 14. Dover,N.J.*..........May, 75.. 4 3 15. Cleveland,O...........Oct. 75. 4 0 16. Washington D. C......Feb.'' 76.: 4 18 17. philadelphia, Pa.......June,: 76.. 5 3 18. Philadelphia Pa........Oct 76.. 5 19 19. New York, N. Y.......Feb: '77.. 5 27 20. Wilkes-Barre. Pa.*.....Mag :77.. 0 3 21. Amenia N. Y..........Oct. 77.. 6 10 22. Philadeiphia Pa........Feb.;' 78. . 6 18 23. Chattanooga' Term.*. . . May' 78. . 7 3 24. Lake George: N. Y....: Oct. 78. . 7 103 25. Baltimore, Md.*.......Feb:' 79.. 7 217 26. ~ittsburgi, Pa.........~a;' 79.. 6 3 27. Montreal, Canada......~ept.;' 79.. 8 121 28. New York, N. Y.*......Feb., '80.. 8 275 29. Lake Superior, Mich....Aug., '80. . 9 1 30. Philadelphia, Pa.*......Feb., '81. 9 275 31. Staunton, Va..........May, '81. .10 1 32. Harrisburg, Pa.........Oct.. '81..10 119 33. Washington, I). C.*....Feb., '82. . 10 226 34. Denver. Colo..........Aug.. '82. . ll 1 35. Boston. Mass.*.........Feb.. '83..11 217 38. Roanoke, Va...........June, '83.. 12 3 37. Troy, N. Y...........Oct.. '83. .12 175 38. Cincinnati. O.*.... Feb, '84..12 4 39. Chicago Ill............May, '84. . 13 1 40. philadelphia, Pa........Sept., '84. . 13 285 41. New York, N. Y.*......Feb., '85. . 13 586 42. Chattanooga, Tenn.....May, '85..14 1 43. Halifax, N. S..........Sept., '85.. 14 307 44. Pittsburgh, Pa.*........Feb.. '86 . . 14 587 45. Bethlehem. Pa.........May, '86 .. 15 Ixiii. 46. St. Louis, Mo..........Oct, 86.. 15 Ixx. 47. Scranton, Pa.*.........Feb.', '87. . 15 lxxvi 48. Utah and Montana.....July '87.. 16 xvii. 49. Duluth, Minn...........July' '87. -16 xxiv. 50. Boston. Mass.*.........Feb.: '88. . 16 xxviii. 51. Birmingham, Ala.......May, '88. .17 xix. 52. Buffalo N. Y..........Oct. '88.. 17 xxiv. 53. New york, N.Y........feb.' ;89 . . 17 xxxi. 54. Colorado..............June' 89 . . 18 xvii. 55. Ottawa, Canada........Oct., 89. . 18 xxiv. 56. Washington, I). C.*. . . Feb. 90. .18 xxx. 57. New York, N. Y........sept:, '93. .19 vii. 58. New York, N. Y.*......Feb. '91. . 19 xxv. 59. Cleveland, O.......... June, :91 . .a xvi. 60. Glen Summit, Pa.......Oct, 111. . 20 lxi. 61. Baltimore, Md.*.......Feb.: '92. .21 xix. 62. Plattsburg, N. Y.......June, '02. . 21 xxxiii. 03. Reading. Pa...........Oct., :92. .21 xliv. 64. Montreal. Canada*.....Feb. 93..21 65. Chicago, Ill............aug.: '93..22 XI. 66. Virginia Reach. Va.*. ...Feb., '04. .24 xwl. 67. Bridgeport Coon.......Oct., '94..24 xxx?. 08. Florida ...'............Mar., '95. .25 xix 69 Atlanta. Ga......... Oct 95. 25 xi 70. Pittsburgh. Pa.*........Feb., '96.. 26 xvii. Trans. No. Place Date Vol. Page 71. Colorado..............Sept. '96. .26 xxix. 72. Chicago, Ill............Feb.. "97.. 27 xvii. 73. Lake Superior..........July '97. .27 xxx. 74. Atlantic City, N. J.*. ..Feb.: :98. .28 xvii. 75. Buffalo N. Y..........Oct. 08. .28 XXXVI. 76. New York,N. Y.*......Feb.: '99. .29 xvii. 77. California.............Sept., ;99. . 29 xlix. 78. Washington, D. C.*.....Feb., 00. .30 xix. 79. Canada...............Aug.. '00. .30 xlv. 80. Richmond. Va.*........Feb.. '01. . 31 xix. 81. Mexico................Nov..'01.. 32 cxviii. 82. Philadelphia Pa. $......May, :02. . 33 xxxv. 83. New Haven, Conn......Oct.. 02.. 33 xlvii. 84. Albany N. Y.*........Feb '03. .34 xxiii. 85. New York, N. Y........Oct.': '03. .34 xi. 86. Atlantic City. N. J.*....Feb., '04. .35 XXIII. 87. Lake Superior..........Sept.'04. .35 dii. 88. Washington. D. C......May' '05. .36 xlii. 89. British Columbia.......July, '05. . 36 90. Bethlehem. Pa.........Feb. '06. .37 xli. 91. London, England.......July: '06. .37 xlviii. 92. New York, N. Y........April, '07. . 38 lii. 93. Toronto, Canada.......July. '07. .38 lix. 94. New York, N. Y........Feb., :08. .39 xli. 95. Chattanooga, Tenn.....Oct.. 08..39 xlviii. 06. New Haven Conn......Feb. '09. .40 xli. 97. Spokane,Wash.........Sept:.'09. .40 xlviii. 98. Pittsburgh, Pa.........Mar.,'10. .41 xxxviii. 99. Canal Zone............Nov.,'10. .41 dv. 100. Wilkes-Barre, Pa.......June. ' 11. . 42 xxxiv. 101. San Francisco, Cal......Oct.. '11..42 xliv. 102. New York. N. Y.*......Feb 12. .43 Ixxvii. 103. Cleveland, Ohio........0ct;' '12.. 44 wii. 104. New York, N. Y.*......Feb.. '13. .45 xv. 105. Butte, Mont...........Aug., '13. .46 ?' 108. New York, N. Y........Oct., 13..47 vii 107. New York. N. Y.*......Feb.. '14..48 xv. 108 Salt Lake City. Otah Aug. :l. 49 5: 109. Pittsburgh, Pa.........Oct., 14. .50 vii. 110. New York, N. Y.*......Feb., '15. .51 xvi. 111. San Francisco, Cal......Sept., '15. .52 xii. 112. New York,N. Y.*......Feb., '16..54 xvi. 1 Arizona...............Sept.,'l6. .55 VII 114. New York, N. Y.*......Feb., '17: .56 vii. 115. St. Louis, Mo..........Oct.. '17..57 vii. 116. NewYork,N. Y.*......Feb.. '18..59 xvii 117. Colorado.....:........Sept.,'18. .60 vii. 118. Milwaukee, Wis........Oct.. '18. .60 x:!: 119. NewYork,N. Y.*......Feb., '19..61 xi. 120. Chicago...............Sept.,' l9.. 62 VII. 121. New York, N. T.*......Feb., '20..63 ix. 122. Lake Superior District. .Aug., '20.. 66 ix. 123. New York, N. Y.*......Feb., '21. .66 xiii. 124. Wilkes-Barre, Pa...... Sept.. : 21.. 66 xix. 125. New York, N. Y.*......Feb., 22. .67 ix. 126. San Francisco. Cal......Sept.,:22. .68 xxix. 127. New York, N.Y.*.....Feb., 23. .69 xxix 128. Canada...............Aug., '23. .69 xxxv! 128.129. New York, N. Y.*......Feb., ;24. .70 xxxi. 130. Birmingham, Ala.......Oct. 24. .71 xxxiii 131. NewYork.N Y.*......Feb.: '25.. 71 xxxviii. 132. 131.Salt Lake City, Utah .. .Sept., '25. .73 xvi 133. New York, N. Y.*......Feb., '26. .73 xxii. 134. Pittsburgh Pa ....... Oct.. '26. .74 xv. 135. New York,' N. Y.*............Feb., '27. .75 x::: 135.136. NewYork,N. Y.*......Feb., '28..76 104 137 NewYork.N. Y.*......Feb., '29. .291 116 138.San FranciscoYork,N.Y. Cal..........Oct. 29..308 406 139. New York, N. Y.*...Feb., '30..30H 1321

Jan 1, 1930

By Jacob Chacko

The east span of the San Francisco-Oakland Bay Bridge (SFOBB), which is one of the most heavily traveled bridges in the world, will be replaced due to seismic safety concerns. The majority of the new bridge will be founded on large-diameter (1.8 to 2.5 meters), approximately 60- to 100-meter-long pile foundations The large-diameter steel pipe piles and soil conditions are similar to those used/encountered in many offshore structures. Thus, the design methods used are based on site-specific modifications to the procedures recommended by the American Petroleum Institute rather than the conventional procedures that have been formulated and used for the design of much smaller piles. Pile foundations will experience their maximum loads during the design earthquake. For the Safety Evaluation Earthquake, tension loads of up to approximately 80 to 90 meganewtons (MN) and compression loads of up to approximately 120 to 140 MN were calculated. Due to the economic importance of the SFOBB and the consequences of catastrophic failure in both economic and human terms, the design and analysis of the pile foundations supporting the bridge consider a number of aspects of pile-soil behavior that are normally ignored. Those aspects include: 1) the effects of consolidation and setup, 2) the behavior under dynamic loading, 3) the losses of resistance under cyclic loading, and 4) the load-settlement behavior of the piles under severe cyclic loading conditions. Since the treatment of complex aspects of pile foundation behavior is not codified in any guiding documents, several project-specific methods were developed for design and analysis of the foundation piles.

Jan 1, 2002

By Jai-Woon Moon, Wonnyon Kim

Deep-sea hydrothermal vents (hereafter chimneys) are commonly found on the new crust forming along divergent plate boundaries. Related to the chimney cycle from birth to death, it is hard to define the growth stage of the chimney due to a brief life span of the venting hydrothermal plume. Here we try to categorize the mineral magnetic properties of the chimneys according to their venting fluid-temperatures. Hydrothermal sulfide deposits in the Southwest Pacific were explored in 2012 and chimneys were collected using remotely operated vehicle (ROV) and Grab with AV camera (GTV). In the present study, mineral magnetic properties of three Cu-rich chimneys were measured: a high-temperature chimney showing a venting fluid-temperature of about 200°C (ROV01); a lowtemperature chimney of about 80°C (GTV01); and an inactive chimney (ROV02). The chimneys were sliced to ~1 cm intervals from core to outer margin. Magnetic properties of ROV01 are dominated by pyrrhotite, except for the most outer part that experienced severe oxidation. Concentration and grain-size of pyrrhotite are relatively low and fine respectively. In the GTV01, pyrrhotite, dominant in the core, is gradually mixed with hematite toward the outer margin of the chimney due to secondary oxidation. Both the concentration and grain-size of the magnetic minerals are greater compared to the GTV01. High concentration and large grain-size of magnetic minerals characterize ROV02. Dominant magnetic phases are pyrrhotite, hematite, and goethite. In particular, the most outer margin shows the presence of magnetite produced possibly by magnetotactic bacterial activity. Such distinctive contrast in magnetic concentration, grain-size, and mineralogy among three different types of chimneys enables the life stage of the Cu-rich chimneys to be determined through a mineral magnetic study.

Sep 1, 2014

By Donald C. Strimbeck

The Bureau of Mines designed a down-fired refractory-lined combustor that efficiently burned pulverized coal to produce a gas suitable as working fluid for an open-cycle gas turbine. The gas contained relatively little carbon, so the load on the ash-separation equipment was significantly reduced. Moreover, reduction in carbon content of the gas increased the average density of the solid particles making them more amenable to removal by centrifugation. Centrifugal-type separators failed to remove sufficient ash; however, to limit blade wear enough to achieve operating periods generally deemed necessary for commercial practicability.

Jan 1, 1969

By Romano J. Micciche

One of the largest scale uses of a multiple, high-strength steel bar tiedown system is described. Tiedowns were installed to resist hydrostatic uplift forces acting on a section of the Interstate Highway Route I-90 southern approach roadway to the Third Harbor Tunnel, in Boston, Massachusetts. Site specific information is discussed regarding design, testing, and installation of Tiedowns. Conclusions are presented regarding the overall performance of this system and the application of this type of tiedown system on future projects.

Jan 1, 1994

By Ingemar Hermansson, Thomas Bjerendal, Mattias Grävare, Carl-John Grävare

"AbstractHigh strain dynamic pile tests (HSDPT) on driven piles have been carried out on a routine basis in Sweden for more than 30 years. The Swedish Commission on Pile research established, in the early 1980s, safety factors based on the percentage of piles tested. The safety factors could then be reduced, creating economic incentives for the contractor to carry out testing.Energy formulas adopted by our neighbour countries, Norway and Denmark, were not accepted in Sweden as a reliable method since the dynamic testing method was considered to be a more scientific and reliable method. It has become almost the only in-situ method used to verify geotechnical bearing capacity on driven piles.The typical Swedish geology of soft soils overlaying very hard strata makes it possible to verify high design loads, typically 20 kN per cm2 of pile cross sectional area for steel piles and 1,5 kN per cm2 for concrete piles.Conventionally a certain percentage of the piles have been tested in Sweden. The EC7, on the other hand states a number of piles to be tested, regardless of the total number of piles. The Swedish NA (National Annex) states a maximum distance between tested piles, which results in better distribution of the test piles over the foundation.For shaft-bearing piles in soft clays, dynamic pile tests have to be correlated by static load tests.Historical backgroundOn a research basis stress-wave measurements have been carried out for a long time in Sweden. One example is a project in the city of Gothenburg, conducted by Fellenius and Pejrud (1964). Strain gauges were glued on the reinforcement bars in 60 m long, precast concrete piles at 3 m and 25 m above the pile tip respectively. Evaluation was done with different methods such as dynamic formulas,stress-wave measurements and in addition compared with static load tests.In the 1975 Building Code in Sweden, driving criteria for concrete piles based on stress-wave theory were introduced, as summarized in Table 1. The driving criteria are intended for 3 and 4 tonne gravity hammers. For hydraulic rigs, which have free-falling hammers, the drop height indicated should be reduced to 80 % of the values in the table. The criteria were considered to include a safety factor of 3,0. For 330 - 450 kN pile load, pile with a standard a cross sectional area of 235 mm x 235 mm was used. For 600 kN load, the standard cross sectional area was 275 mm x 275 mm."

Jan 1, 2014

By J. Drelich, M. Pawlik

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size, and distribution of mineral inclusions in coal, on its wettability are briefly reviewed.

Jan 1, 1999

By C. Velásquez, W. Bergholz, C. Spence, P. Lind

NuevaUnión SpA (NuevaUnión) is a development project located in the Huasco province of the Atacama region of Chile. It is held in a joint venture company owned 50:50 by Teck Resources Limited (Teck) and Newmont Goldcorp. It includes the Cu-Mo Relincho deposit and the Cu-Au La Fortuna deposit, with plans to utilise a single concentrator to be built at the Relincho site. The Relincho site is at an altitude of 2,000 masl and is 40 km from the La Fortuna site which is at an altitude of 4,100 masl. The project is currently completing a Feasibility Study and is reviewing equipment selection and flowsheet options. This paper is based on the current thinking, and design decisions will be finalized at the completion of the Feasibility Study. NuevaUnión is currently planning for phased operation, processing Relincho ore at 104 ktpd followed by processing ore from La Fortuna at 116 ktpd. Plans for the third phase include doubling the main processing lines and returning to Relincho ore at a processing rate of 208 ktpd. The NuevaUnión concentrator will incorporate comminution and flotation circuits that are being designed to maximize the overall economic value of the combined ore deposits. Major ore characteristics differ between the two ore bodies, such as ore competency, grindability, liberation grind size, pulp rheology, tailings properties, minerals and metals of value, as well as gangue mineralogy. Mineral processing choices have been made to optimise value from each deposit and the combined project. INTRODUCTION Between 2010 and 2013, two significant mining projects were being developed in Chile: Goldcorp’s El Morro project had recently finalized a Feasibility Study and, in 2011, had received its environmental approval for construction; and Teck Resources Limited’s (Teck) Relincho project was finalizing a Feasibility Study and preparing its Environmental Impact Study. Both projects were: Geographically close, at only 40 km apart. Considering similar infrastructure. Each was planning to have its own concentrator, tailings management facility, high voltage power line, port, concentrate transport system, seawater desalination plant and pumping system to mine site.

Jan 1, 2019

By V. McLemore, A. Fakhimi, K. Donahue, D. Sweeney, V. Viterbo

In order to evaluate the relationships between weathering and durability and strength of rock samples from the Goathill North rock pile at the Molycorp Questa mine, NM, we conducted slake durability and point load tests. Slake durability index (ID2) values ranged from 84 to 98%. Point load strength index (Is50) averaged for all rock units ranged from 1.1 to 5.7 MPa. Results show a slight positive trend between ID2 and paste pH. Two populations of data are distinguishable when ID2 is plotted versus the percentages of chlorite, illite and internal friction angle. In general, Is50 values increase toward the interior of the rock pile. Preliminary conclusions indicate that the durability and strength of the rock pile material generally increase toward the interior of the rock pile. Pre-rock pile alteration and post-rock pile weathering history have affected the durability of the GHN rock pile samples.

Jan 1, 2007

By Congling Shi, Marek Borowski, Yue Wang, Jianwei Cheng, Xixi Zhang, Xuan Xu

As the first barrier to prevent accidents caused by explosions in underground coal mines, the integrity and stability of mine seals have great effects on mine workers’ lives and underground production safety. In this paper, the mechanical responding performance of typical mine seals under the impact load are studied by using numerical simulation method. By such simulation studies, the safety of different seals subjected to the explosion load is evaluated. Seals’stability are also investigated under effects caused by various influence factors including thickness of mine seal, cutting depth into surrounding rocks, rock type, and the roof-tofloor convergence under given the explosion load. The research results can provide theoretical basis and reasonable improvements for mine seal’s construction practices for improving its anti-explosion performance.

By Congling Shi, Marek Borowski, Yue Wang, Jianwei Cheng, Xixi Zhang, Xuan Xu

As the first barrier to prevent accidents caused by explosions in underground coal mines, the integrity and stability of mine seals have great effects on mine workers’ lives and underground production safety. In this paper, the mechanical responding performance of typical mine seals under the impact load are studied by using numerical simulation method. By such simulation studies, the safety of different seals subjected to the explosion load is evaluated. Seals’stability are also investigated under effects caused by various influence factors including thickness of mine seal, cutting depth into surrounding rocks, rock type, and the roof-tofloor convergence under given the explosion load. The research results can provide theoretical basis and reasonable improvements for mine seal’s construction practices for improving its anti-explosion performance.

By Richard E. Danell

"There are a variety of approaches for wall control blasting in open pit mining operations. Safety forworking in the pit is the principal benefit. There are also a number of economic and productivitybenefits when appropriate techniques are used. The purpose and requirements of wall control blasting can vary quite significantly for different operations. When considering blast design, geology, geotechnical factors, drilling, explosives, economics and blasting history are all part of the engineering design process. In many operations, there is a high reliance on blasting history and economics for determining wall control blasting measures. This presentation outlines approaches that broaden the design process and discusses their advantages."

Jan 1, 1997

By Hui Wang

With the great increasing use of nickel metal hydride batteries recently, the waste of this kind batteries have been paid for close consideration. For the main reason that the waste of the batteries contained precious metals and lanthanide which cost great lose. This paper introduces the pyrometallurgical process of recovering nickel and cobalt from the waste of the nickel metal hydride batteries. Particularly, the waste for the process was from factory during the producing program. The use of designed solvent to divide nickel and cobalt in melted state from the waste is described. Also, the result of the nickel and cobalt and melted gangue that mainly consist of lanthanide oxide are included in details. The aim of the paper is to find out a simple and feasible way to reuse waste from nickel metal hydride batteries.

Jan 1, 2009

By J. E. Nesset, F. Rosenblum, J. A. Finch

"The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to highly reactive and potentially hazardous to both humans and infrastructure. It is essential that there be a reliable test methodology that can measure and categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral mixtures making it difficult to predict their self-heating behaviour a-priori based on mineralogy or with a simple “snapshot” test. Furthermore, self-heating behaviour will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to measure and reliably predict the latent self-heating hazard of a sulphide material. Several of the methods were tested and compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.INTRODUCTION Sulphides as well as other materials (coal, wood chips, hay, powdered milk, to name a few) that are stockpiled in an air atmosphere may undergo oxidation reactions which can result in the evolution of heat (Beever, 1984) (Hudak, 2002) (Blanchard, 2007). If the rate of heat generated exceeds the rate of heat dissipation, the stockpile temperature will rise, potentially leading to “hot spots” in the most reactive areas, and possibly even fires. The heat generation rate, the “self-heating” rate, depends on many factors such as the type and composition of material, particle size, moisture content, oxygen availability, ambient temperature and humidity, and of prime importance, the extend of prior oxidation, or more specifically, the presence of oxidation products. The desire of operators that mine, process or transport sulphide-bearing materials with a potential for self-heating is to have an accepted and reliable method for evaluating and quantifying the potential hazard of their material. The challenges are how to best measure the self-heating properties of given samples, and based on results, predict the behaviour of the bulk material over time and in-situ. Generally, when evaluating a given material one derives the self-heating characteristics of that sample at the time and under the conditions of testing, which will be referred to as a “snapshot test”. If that material is invariable, i.e. it will not change its response over time, then it may be considered to be a “predictive test”. However, if as a result of continuing oxidation or other changes, the material becomes more or less reactive with time, then a “snapshot test” is unreliable with respect to predictive ability."

Jan 1, 2014

By C. Pelley, S. Kelebek, T. Katsabanis, B. Nanthakumar

"As part of a larger investigation on generation of fines from mining activities and their effect on downstream operations, ore samples from Onaping area stockpiles of Falconbridge Ltd were studied. Batch flotation tests were conducted on the stockpile samples and fresh ore samples to explore the effect of stockpiling on grade-recovery performance. Head grade and particle size distribution of the samples from stockpiles were adjusted so that the samples compared are similar to each other. In additional tests, fresh ore samples were blended with stockpile samples at various percentages, representing 27.4, 50.2 and 81.5% of stockpile samples.The samples from stockpiles produced inferior nickel grade-recovery curves compared to fresh ore. The poorer grade-recovery performance was attributable to two factors. First, a significant dilution effect was observed due to the nearly complete flotation of pyrrhotite. Secondly, while pyrrhotite from stockpiled ore became highly floatable, the same stockpiling conditions caused nickel losses that were attributable to non-floatability of some pentlandite.In the case of blending, there was generally insignificant difference in the nickel grade-recovery between fresh and blended samples when the blending cases involved 27.4 and 50.2% stockpile samples. However, an increase in pyrrhotite recovery was observed for both blending cases. At 81.5% blending case, degraded grade-recovery was significant primarily due to the nearly complete flotation of pyrrhotite. There was a small, but noticeable amount of nickel loss for this case. However, for lower ratios of blending this loss was negligible.The increase in pyrrhotite recovery was partly attributed to its activation by Cu and Ni ions. Formation of a significant amount of elemental sulphur was also apparent from analysis of stockpiled samples. It can be concluded that pyrrhotite is mildly oxidized under stockpiling conditions while part of the pentlandite undergoes a more severe oxidation."

Jan 1, 2006