Search Documents

By M Wilson, D Whiteman, P Kuiper, S Talu, G Watt, A van As

Once the draw process has begun in a block cave, it is very difficult to identify which regions of the cave have successfully propagated, where the caved material is flowing from and where it is flowing to. The uncertainty around cave flow increases as the cave is drawn and can be further compounded by poor draw control practices. These uncertainties make it difficult to plan effective draw strategies to control dilution, as flow model predictions tend to gradually diverge from the actual state of the cave. There have been documented occasions where observed caving phenomena, such as muck pile surface rilling, could not be reproduced with the cave flow models of the time. The ultimate consequence of cave flow uncertainty is generally manifest as higher dilution and lower grades.In order to measure the real-time flow of caved material within an active block cave, CRC Mining and Elexon have developed, together with Rio Tinto, a cave flow monitoring system called Cave Tracker, which is being trialled at Argyle Diamond Mine (ADM) in Western Australia. The Cave Tracker system at ADM comprises electronic ‘beacons’ that have been installed down long HQ diameter drill holes located above the extraction level. As the cave-back propagates and the rock mass fragments, beacons are released into the muck pile and flow along with the caved material to the drawpoints below. At Argyle, the beacons are configured to emit a signal every three days. These signals are picked up by detectors installed on the extraction and undercut levels, allowing the positions of the beacons to be determined.By examining the real-time material flow in different regions of the cave, flow mechanisms can be better defined. Draw control strategies can then be actively tailored to manage the current state of the cave. Thus, previously undetectable indications of excessive rilling, rapid cave propagation, cave stall, air gaps and dilution entry can now be identified early and assessed continuously as the cave progresses. For the first time it is possible to amend draw strategies based on measurements from inside and outside of the fractured zones, allowing caves to be managed more effectively.CITATION:Whiteman, D, Talu, S, Wilson, M, Watt, G, Van As, A and Kuiper, P, 2016. Cave Tracker flow monitoring system installation at Argyle Diamond Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 479–488 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Robert P. Bruno

This report covers the study of the feasibility of using a hand-held infrared viewer as a methane indicator to observe methane gas at the face of an underground coal mine. The objective of this program was the development of a hand-held device to remotely detect the presence of concentrations of methane gas in underground coal mines. Convenient "mapping" of methane from a remote location would allow rapid and safe corrective procedures for working personnel. Modified commercially available equipment was evaluated both in the laboratory and in a working mine. Although readings were obtained and the general principle of operation demonstrated, the power levels necessary, and protective enclosures required, would raise the weight of the instrument beyond practical limits of portability. Based on currently available technology, it is the conclusion of the investigations that a practical, portable, hand-held visual methane indicator is beyond the state-of-the-art. The recommendation was, therefore, made that work be suspended, and the results and data compiled and presented in a final program report.

Jan 1, 1979

Errors in ore reserve estimation can occur during drilling and sampling, sample preparation and analysis, geological logging and modelling, database construction, statistical or geostatistical evaluation, selection of economic parameters, selection of ore reserve method and assessment of mining constraints. Core sample recovery can be a major source of error, and it is proposed that the modelling of grade, metal accumulation and thickness should be accompanied by the modelling of core recovery (or core loss) so that for each ore block a weighted block recovery factor is obtained. This gives a good indicator of the reliability of a reserve estimate. It is suggested that a resource reliability rating (RRR) system be established to quantify what is meant by geological assurance and to combine this with an estimate of the precision of estimation as gained by geostatistical analysis. Proven and probable minable reserves would be those with an RRR better than 50% and a precision of estimation better than 20%

Dec 1, 1996

By Richard Phiri, Mike Milupi, Jackson Kapobe, Anton Lemmer, Charles Mazala

Sustainability of plant operations in a rapidly changing mining environment requires a well-trained workforce to ensure smooth running of operations. To ensure availability of trained labor, Mopani Copper Mines PLC set up a training facility in 2013. The school offers training in Engineering, Mining and Process. The engineering section enrolls grade 12 school leavers for artisan training. Mining section offers comprehensive safety induction program to employees and contractors to meet the Mopani zero tolerance accidents safety policy. The process training section offers advanced training programs for plant operating personnel and university graduates. The program includes needs analysis, theoretical metallurgical modules, practical plant training and e-learning modules. The school also offers assaying and sampling courses. All the above courses are extended to individuals and other mining houses outside Mopani wishing to have their personnel trained. The Mopani sustainable development academy ensures that contractors engaged on the Mopani sites are fully registered, comply with all relevant regulations and have undergone induction program before they can be allowed to work on the mine. INTRODUCTION “Sustainable operation of the mining industry requires a continuous supply of trained human resources” (Kapobe et al., 2018). The publication by the Asian Development Bank (2014) argued that there was a mismatch between the demand for high-level skills and the oversupply of low-level skills. Globally, the mining industry requires continued supply of skilled manpower for its complex operations and long term projects whose sustainability is absolutely necessary. Implementation of newer technologies in plant operations to ensure cost effective and efficient operations requires trained and skilled labor at various levels to handle ever-changing challenges. Dutz (2007:152–156) made three recommendations for Building Worker and Management Skills in India: Strengthen enterprise - based training. The government should help ensure that the benefits of in- service training are widely recognized by enterprises, while simultaneously providing strong financial incentives Improve vocational training - Vocational education and training systems have been unsuccessful in preparing graduates to meet market needs, particularly because of a lack of interaction with industry. Public and private vocational education and training providers should be strengthened to make them more responsive to industry demands. Curricula should be updated to reflect modern technologies. Strengthen business, management education, management of research and commercialization - business and management education should be strengthened through public-private partnerships. Innovative management courses should be introduced. Although these recommendations were made for India, they also apply to Zambia and other low and medium income nations.

Jan 1, 2019

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining' the potential fur reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By S. Lubbe

South Africa and Australia are the biggest suppliers of zircon sand to the international zirconium industry. However neither South Africa nor Australia is well known for zircon beneficiation. Geratech Zirconium Beneficiation Ltd (GZB) continued with additional research on sodium hydroxide (NaOH) cracking of zircon sand during 2002-2003. In 2003 GZB started extracting zirconium from zircon sand by means of NaOH cracking on a commercial scale. Experience has shown that temperature profile and atmospheric control inside the furnace is crucial for the beneficiation of zircon sand. Silica carryover to zirconium chemicals could result if a high temperature is used. Once the sodium silicate is extracted from the sodium zirconate and dissolved in hydrochloric acid, two distinct routes can be followed to precipitate various zirconium chemicals. The most common route is to precipitate zirconium oxychloride crystals (ZOC), with subsequent purification from all contaminants (crystal route). Less known is the process (liquid route) that involves the direct precipitation of zirconium basic sulphate (ZBS). This route will yield a less pure product, with contaminants such as silica and titanium. An important factor in this route is the prevention of silica gel formation, which could hamper final product filtration. For applications like paint drying (zirconium octoate) or antiperspirants (zirconium hydroxychloride) low levels of contaminants have no effect on the final product. The advantage of the liquid route is fewer production stages compared to the crystal route. The disadvantage of the liquid route is that the market for the products will be significantly smaller. The optimum solution could be a plant design that could cater for both routes. Another example of an application of zirconium chemicals is the use of ammonium zirconium carbonate (AZC) in the paper industry. Zirconium basic carbonate (ZBC) is dissolved in ammonium carbonate to produce AZC solution. AZC is used mainly in European countries in the paper industry. For example, carton boxes were initially produced with formaldehyde as the binder, however, it has now been replaced with AZC since formaldehyde is considered toxic. AZC reacts with the cellulose fibres in the paper to act as the binder. The resulting product is not toxic, and printing ink dries very quickly due to the porous paper structure. Other applications of zirconium chemicals involve the use of acid zirconium sulphate tetrahydrate (AZST), zirconium orthosulphate (ZOS), potassium zirconium carbonate (KZC), and zirconium hydrous oxide (ZHO). Fluoride-based zirconium chemicals like zirconium tetra-fluoride (ZrF4) and hexafluoro-zirconic acid (H2ZrF6) are used in the aluminium industry. Zirconium oxide (Zr02) can be produced from any of the abovementioned precipitated chemicals via a high-temperature decomposition process. The physical properties of such oxides can differ tremendously, depending on the final application. The fired density of sanitaryware is typically 5.8 g/cm3, compared to milling media at >6.1 g/cm3. The required fired density is achieved by controlling the precipitation and decomposition conditions for these two oxides. The same applies to stabilized and mixed oxides, for example where zirconium oxide acts as an oxygen carrier in fuel cells.

Jan 1, 2012

By A. Ersoy, M. D. Waller

The principal factors which require consideration in predicting drilling rates are the bit-type, the bit operating parameters and the characteristics of the penetrated rock. A single index is not a sufficient basis for predicting performance. A variety of rock types were drilled in the laboratory with polycrystalline diamond compact (PDC) and impregnated diamond core bits using a fully instrumented drilling rig at different rotational speeds and with a range of weights on the bit. Quantitative determinations of a wide range of textural, mechanical and intact rock properties were also made. Multi-variable linear regression analysis was then used to develop predictive models of rates of penetration from the operating and rock property data. The models have been verified by statistical tests. The analysis indicated that the models for the pin and hybrid PDC bits have potential for practical application. However, although the model for the impregnated diamond bit appears to be reasonable from a purely statistical point of view, it may not be satisfactory for drilling uses as it is based on two measures of rock hardness alone. The application of multiple regression analysis to PDC drilling performance is novel and the technique shows promise for the prediction of rock drillability with PDC bits. The ability of the technique to provide a mathematical characterisation of the performance of new drill bits in specific rocks may prove to be of value to drill manufacturers and users

Aug 1, 1995

Prefeasibility planning and cost estimation of conveyor systems has historically been undertaken by comparing fixed plant transport requirements to that of similar systems in service. This paper describes the development of a prefeasibility conveyor technical design and cost estimation application using Microsoft Excel Visual Basic for Applications (VBA) platform. The application tool known as D-Convey (Dachshund Convey) was developed with the goal enabling the end user:- to develop a technical model for conceptualised conveyor systems,- to perform economic analysis on the developed technical model, and - to conduct a comparative and risk analysis.An Excel VBA based platform was utilised to draw upon both the analytical and graphical capabilities of a spreadsheet. Some of the features of D-Convey system include a revolutionary dynamic graphical help system, known as the 'information pane' in lieu of traditional help files as well as the use of familiar graphical user interface elements such as the MS Office 2007 task ribbon. The D-Convey system incorporates material database allowing for mass handling prefeasibility estimation in other industries; it has been validated at a local quarry.

Dec 6, 2010

By Ronald Molnar

"High demand for metals is driving the exploitation of lower grade and more complex orebodies. These projects are often the initiatives of junior mining companies with limited financial resources. In addition, existing operations seek to enhance revenue from their existing metal recovery operations, through the production of value-added by-product metals and chemicals. Typically, hydrometallurgical circuits, often with novel chemistry, are required to exploit these new ores, to produce the multiplicity of products that will make a marginal project economical, or to increase the product range of an existing operation. Often, the mineral processing engineer is given the task of coordinating the development of a back-end hydrometallurgical flowsheet for their mineral processing project. This paper discusses the objectives that companies have when they commission the operation of a hydrometallurgical pilot plant. The paper goes on to enumerate some of the principal differences between mineral processing and hydrometallurgical pilot plants and the effect these have on the design, operability and potential pilot plant outcomes. Important factors include working with chemically reactive solutions and pulps, elevated temperatures operation, changing rheological properties of slurries, the complexity of integrated circuit flowsheets with long hold-up times and multiple recycle streams, and the need in some cases for extreme attention to purity and cleanliness. Examples will be drawn from the extensive experience base of SGS Minerals Services at the Lakefield site, in piloting both mineral processing and hydrometallurgical process flowsheets.INTRODUCTIONWe are currently experiencing a period of strong growth in the demand for metals. This in turn is turning the spotlight on a great many smaller mining companies and mining promotion ventures trying to tap into the rising metal demand. Some of these companies want to develop their properties and recover metals while others want to develop to the point that a major company will take an interest, or in some cases buy them out completely.With the heightened interest in metals, many orebodies that have been known about for years are being reconsidered for exploitation. Often, the reason they have not been developed to date is because of difficult metallurgy and marginal grades leading to marginal economic viability. In both cases the key that unlocks the resources is often the application of a novel metallurgical flowsheet, often a hydrometallurgical flowsheet."

Jan 1, 2006

By A. P. Squelch

The question of what stress condition exists in the hangingwall of tabular stopes remains topical and largely unanswered. Limited field data exist to quantify the situation and provide calibration for investigative computer modelling exercises. Work conducted in1989 and 1990 under a Chamber of Mines Research Organization (now the CSIR: Division of Mining Technology) programme of research into the behaviour and benefits of backfill may assist with this situation. The original work was motivated by the premise that the improved hangingwall stability in backfilled panels (identified by rockfall accident analyses) is due to a change in the hangingwall stress regime. Current, largely theoretical, studies into mechanisms of stope hangingwall behaviour and support interaction could benefit from considering these data. Keywords: Backfill, horizontal stress, stope hangingwall, hangingwall stability, support interaction.

Jan 1, 2002

By D. V. Karandikar

Contiguous bored piles have been used in the past for retaining the sides of deep excavation. An innovative version of this method was adopted successfully in two prestigeous projects in Bombay in which in a very constricted and congested locality, adjoining seashore at Walkeshwar, 14 m deep excavations with vertical sides were required. 600 mm dia bored cast-in-situ piles were first installed at 1.2 m c/c and subsequently as the excavation proceeded, they were tied to cast-in-situ RCC waling beams. The shear connectors to the beams were pre-fixed to the pile reinforcing cage at specified depths. The pile / waling beam system was anchored into the ground by installing inclined prestressed cable anchors at the designed depths. The waling beams were also used to support the brickwalls, which formed the required backup wall for fixing the tiled water proofing system. Catch-drains were installed behind the brickwalls for relieving the ground water pressure and thus ensuring a very economic design. The adequacy of the system was proven in that where the system was not installed in time, failure of the sides occurred during monsoon. Whereas in the areas where the above retaining system was installed, there were no problems inspite of heavy monsoon and surcharge of construction materials and equipment. The system became a very effective and economic alternative to an anchored diaphragm wall. The paper presents the case studies of these two projects.

Jan 1, 1996

By L Bartsch, M Kelahan, E Wingate, J-S David

The use of column flotation cells for recovery of phosphate is becoming more common practice in certain parts of the world (Brazil, Russia) where igneous phosphate ores are processed. Igneous phosphates are generally finer grained (< 200µm) than some of the traditional sedimentary phosphates (<400µm). Australian phosphate from the Georgina basin is sedimentary, but has a much finer grain size (typically < 106µm) than similar deposits in North Africa and the USA.In 2013, Arianne Phosphate completed a bankable feasibility study for the development of their igneous phosphate deposit at the Lac a Paul site in Quebec. Initially, lab test work and bench scale piloting indicated that using traditional mechanical flotation would be able to produce adequate concentrate grade and an economic level of recovery, but would necessitate the installation of a complex and operationally challenging flotation circuit. Later pilot plant testing using column cells resulted in a significant reduction in process complexity and facilitated the processing of the -20µm ore fraction which resulted in a 10% increase in P2O5 recovery and a 5% increase in concentrate grade %P2O5.Flotation column testing achieved a concentrate grade of 38.6% P2O5 at a P2O5 recovery of 90%. Using a mechanical flotation cell circuit, the concentrate grade was 36.4% P2O5 with a P2O5 recovery of only 78.8%. A noticeable feature of the testing was the simplicity of the column flotation circuit configuration (Rougher + 2 stages of cleaning + Cleaner Scavenger) compared to the mechanical flotation cell circuit (Rougher + Scavenger + 3 stages of cleaning).The financial benefit for this case study was estimated using a sales price of US$ 195/t FOB for a 38.6% P2O5 product, and an assumed cost of production of US$ 95/t, the netback price is calculated at US$100/t. For a daily milling rate of 55,000t/d, the improved flotation performance provides additional concentrate production of 1,203t/d. Using the netback price calculated above, this calculates to additional gross profit of US$ 120,260/d.Annualised, this equals US$ 40.7 million in additional revenue for a similar or reduced CAPEX.The use of column flotation on fine grained phosphate ore types often requires fine grinding and desliming to liberate the phosphate value, such as the Australian sedimentary phosphate ores. This may enable the development of deposits previously regarded as uneconomic.This paper discusses the potential benefits available to operators, and developers of new projects, for the use of column flotation cells in their metallurgical circuits as assessed by an engineering company.CITATION:Wingate, E, Kelahan, M, David, J-S and Bartsch, L, 2015. Does it make cent$ to use flotation columns for phosphate beneficiation?, in Proceedings MetPlant 2015, pp 353–365 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Dean Workman

Located in downtown New York City, this project necessitated an innovative conveyor design for successful muck removal. This paper will discuss the technical challenges and engineering solutions of the muck transport system which consists of every commonly recognized version of a belt conveyor. The elaborate system includes a TBM conveyor integral to the back-up system, a wall-mounted extensible conveyor, a crown-mounted transfer conveyor, a floor-mounted fixed-length conveyor, a pocket-belt vertical conveyor, three cascading overland conveyors, and one radial stacker. The most challenging design element was an over-land conveyor featuring a box truss for muck transportation over Northern Boulevard while simultaneously going under the Queens Plaza railroad viaduct. An overview of the project is provided along with the following topics: developing final plans from the proposal concept, interfacing with existing works, communication with the joint venture, and complying with local regulations.

Jan 1, 2008

To allow routine measuring of the exposure of underground workers to N02 from diesel engines and residual gases from blasting. The Approach: A miniature sampler absorbs NO2 which can be measured using a simple method adaptable to both multiple automatic analyses or individual on-site analysis. How It Works: The NO2 sampler is encased in a plastic tube approximately half the length of an ordinary ball point pen and clipped to an underground worker's hard hat. Removal of the end cap activates the personal sampler. Air from the working place enters the open end and diffuses at a controlled rate down the tube interior. The diffusion rate is dependent on tube dimensions (ratio of cross-sectional area to length). The closed end of the tube contains stainless steel mesh which is coated with triethanolamine (TEA) for absorbtion of all NO2 reaching it. Other oxides of nitrogen are not absorbed. The amount

Jan 1, 1975

By Harold J. Rose

The economic situation in Switzerland during recent years has resulted in theoretical studies , engineering development work , and many commercial installations of ingenious methods for using energy more efficiently . The purpose of the present investigation was to learn of recent Swiss developments for the more effective use of coal , which comprises 98.9 percent of the romaining known mineral - fuel reserves of the United States .

Jun 1, 1947

By P. C. McWilliams

Theoreticians in soil mechanics have been pursuing a probabilistic approach to the factor of safety of an embankment or darn for the past 10 years. The motivation for this work is in contrast to the current practice of deterministically computing a factor of safety and treating it as an absolute with no regard to its inherent statistical variability. Basic to the probabilistic approach is the selection of an appropriate statistical model to represent the histogram or probability density function (PDF) of the factor of safety values, Rather than simply assuming which PDF is appropriate, the Bureau of Mines collected data at two waste disposal embankments for consideration, This report addresses three candidate models, using the techniques of nonlinear curve fitting, and identifies the "best" model. A propagation of error formula for estimating the variability of Fellenius? factor of safety is also discussed.

Jan 1, 1983

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. shuttle car. These instructions are based upon actual installations made in the mine on two shuttle cars, model 21SC-2E. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other shuttle cars with similar protective canopies. Skilled mechanics can determine if the instructions hexein would he applicable to the other shuttle cars and can determine any necessary modifications if they are not.

Jan 1, 1973

By D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2005

By D Beahm

Introduction The Energy Metals Corporation (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin including the JAB Property, one of several potential properties being planned for development as a satellite facility to the greater Antelope Uranium Project. A National Instrument 43-101 Technical Report has been completed for the JAB property. This report estimates total measured and indicated mineral resources on the property totaling 3,555,022 pounds U3O8 contained in 2,400,875 tons at an average grade of 0.073 % U3O8 at a .25 GT cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB Property is located in Sections 13, 14, 15, 16, 21, 22, and 23, Township 26 North, Range 94 West, approximately Latitude 42o 14’ North and Longitude 108o 00’ West (Figure 1, Location Map). This property consists of unpatented mining lode claims and Wyoming State mineral leases comprising approximately 2,100 acres.

Jan 1, 2007

By S F. Simmons

The Ohaaki Rhyolite and the Rautiwiri Breccia are two volcanic units occurring in the shallow and deep parts of the Broadlands-Ohaaki geothermal system. Alteration of these units by chloride waters results in distinct mineral assemblages that also have distinct whole rock compositions. The Ohaaki rhyolite is altered to an assemblage dominated by quartz, adularia, illite and pyrite as a consequence of silica, potassium and sulfur metasomatism. Locally, these rocks contain up to 0.5 ppm Au. The Rautiwiri Breccia by contrast is altered to an assemblage dominated by albite, adularia, quartz, illite, chlorite and pyrite in association with modest sodium metasomatism. Whole rock oxygen isotope compositions of altered rocks range between 3.3 and 7.5 ë, and are generally lower compared to their fresh rock equivalents having values of 9.5 to 10.6 ë; the result is broad pattern of lower values with increasing alteration intensity.

Jan 1, 2002