Search Documents

By Ryan W. Ulansky

This paper presents the conceptual design of a magnetically-levitated skip for use in an underground mine. A skip is used to move rock from an underground mine to its surface processing facility. Conventionally the skip is raised and lowered by cables, similar to an elevator. In a magnetically-levitated skip, the cable is replaced with a linear induction or synchronous motor to provide propulsion and levitation. Removal of the cables in a magnetically-levitated skip provides many advantages over a conventional system including the ability: to negotiate corners, to travel vertically in the shaft as well as horizontally to the mining face, and to move a very large volume of material using multiple skips in a small shaft. A magnetically-levitated skip is a safer, more environmentally-friendly, productive alternative to conventional skipping. It has the further advantage to decrease haulage distances for underground vehicles.

May 1, 2002

[This Bureau of Mines report presents results of a survey of underground mining equipment and of two demonstration programs showing the feasibility If quieting; a load-haul-dump (LHD) machine and a personnel vehicle. Typical noise levels are presented for the major machine types used in underground mines, along with estimates of the noise overexposure of miners who operate or work near these machines. General principles of noise control are explained, and the application of these principles is illustrated in the description of modifications made to the LHD machine and the personnel vehicle. The noise control package installed On the persona of vehicle lowered its noise level by 14 dBA after 4 months of operation, and inspection of the LHD machine after 2 1/2 years of operation with the modifications showed its noise level 7 dBA lower than that of the unmodified machine. Noise dosimeter measurements indicated that both machines were in compliance with Federal noise regulations for a typical shift.]

Jan 1, 1980

By Oliver C. Ralston, Dorsey A. Lyon

The data reported in this bulletin are largely the result of experiments conducted by the Salt Lake City station of the Bureau of Mines in cooperation with the department of metallurgical research of the University of Utah. The work on lead is only one of the phases of the investigations carried on at that station during the years 1914 to 1916. The results of similar work with zinc ores and with copper and other ores will be published in future reports of the bureau.

Jan 1, 1918

By Steven A. Mathe, Seokbin Lim

Current analytical models can accurately predict the final velocity of explosively driven flyers and can somewhat predict the acceleration profile, but do little to address the deformation of the flyers. Explosive systems such as linear shaped charges and explosively formed projectiles, which can be described as multiple interacting explosively driven flyers, often involve interactions between the flyers that occur much before the flyers reach their predicted final velocity. In this regime, it is important to accurately understand both the acceleration profile and the deformation profile of the flyers, as both significantly affect the functioning of the explosive systems. Previous work proposed an analytical model to meet this need. As the expanding gas cloud of detonation products drives the flyers, rarefactions impinge upon the gas cloud from around the flyer edges, which produces a pressure difference across the back face of the flyer leading to deformation of the flyer. Previous research condensed the effects of the rarefactions into a single term, the pressure release ratio, ?, which was calculated based on hydrocode simulations of a block of explosive only and an assumption of isentropic expansion. This work intends to determine the value of ? for different explosive compounds. The results of this analysis were compared to hydrocode simulations of an open-faced sandwich configuration explosive/flyer system with an average accuracy of 15% across the tested compounds.

Jan 1, 2015

By Minna Karstunen, Patrick Becker

"Abstract The deformation behaviour of a foundation on deep mixed columns in a natural soft soil is a three-dimensional problem, which has to be considered adequately in numerical modelling. However, simplifications are often made due to the computational costs of fully coupled 3D analyses by either modifying geometry of the problem or material parameters in 2D for plain strain analyses or by modelling the problem as 2D axisymmetric case. The volume averaging technique (VAT) is an enhanced 2D FE technique that enables mapping the 3D problem in two-dimensions, yet modelling the two constituents (column and soft soil) with appropriate different constitutive models within a homogenized material. The performance of the volume averaging technique is demonstrated by considering unit cell simulations of floating and end bearing columns in soft soil. The results with VAT are compared and validated against conventional 2D axisymmetric and fully coupled 3D finite element analyses.IntroductionThe properties of very soft clays, silts and organic soils can be improved by stabilizing agents, such as lime and/or cement that are mixed into the soil in situ by using auger-type mixing tools in situ. Deep mixed columns are extensively used to reduce deformations and to improve the overall stability of embankments and foundations on soft soils. Whilst the most typical applications are embankments, increasingly the method is used under foundations. The first category of applications is very common in Scandinavian countries, whilst the latter application has been pioneered in Poland, as an environmentally friendly (low CO2) and cost effective alternative for piling. Due to economic and environmental reasons there is an increasing interest in the technique elsewhere in Europe. With deep mixing, the strength and deformation properties of the soft soil can be improved, and the risk of unwanted deformations is substantially reduced.Numerical methods, such as finite element (FE) analysis, can be used as an alternative to conventional design methods. They are particularly suitable when considering serviceability limit state, i.e. deformation analyses under working loads. FE analyses allow using advanced constitutive models that take account of the complex stress-strain behaviour of natural soil and stabilized columns, respectively. The problems that involve a grid of circular columns under an embankment or a strip footing are fully three-dimensional problems. As 3D analyses are very laborious and expensive, an enhanced 2D technique using the so-called volume averaging technique (VAT) is utilised. The basic idea is to describe the column-improved ground as a homogenized composite material, and using clever mathematics to map the true 3D problem into 2D. Once the constitutive relations of both composites are defined, the response of the column-improved ground can be simulated in 2D subject to arbitrary loading and boundary conditions."

Jan 1, 2014

"Polycom, a new approach to ore processing based on pressure comminution, is obviously a very attractive alternative to conventional processing methods.Since a full-scale pilot plant was commissioned in 1986, more than 125 commercial installations, with capacities up to 1000 t/hr, have gone ahead.Already successfully used in processing cement clinker, limestone, coal, and other minerals, Polycom high pressure grinding results in:o Significantly reduced capital costs, because smaller units can be used m new installations;o Capacity increases of up to 100% in existing facilities; and o Operating economies that include energy savings of 20% or more, and reduced wear parts consumption.1. IntroductionAutogenous or semi-autogenous mills in conjunction with rod or ball mills are used with preference for ore processing. Most ball mills are of closed-circuit design and operate with mechanical classifiers (spiral or rake classifiers) or hydrocyclones. In other words, the ores undergo wet primary grinding, since slurries are required for the downstream separation stages anyway. This paper presents a new grinding system based on high pressure comminution of ores. This grinding process allows:- Energy savings of up to 20 % or more- Capacity increases of up to 100 % and more- Reduction of wear costs- Smaller units for new installation and thus- Reduced investment costsThese advantages are highly interesting for both new installations and conversion projects, particulary in cases where an increasing hardeness of the ore, i.e. rising Bond Work Index, reduces the output of the plants or where the metal assay of the ore decreases and the capacity of the existing systems has to be increased. POLYCOM high-pressure grinding rolls have established themselves with great success already for grinding cement clinker, granulated blast furnace slag, limestone, cement raw materials, coal and other materials.Meanwhile more than 250 high pressure grinding rolls have been installed worldwide. Capacities up to 1.000 t/h with roller diameter up to 2.8 m and drive units up to 2.400 kW are installed."

Jan 1, 1991

By G. Balletto, C. Furcas

"The mineral raw materials industry is a key-component of the Gross Domestic Product of industrialised economies, closely related to both the building and the industrial sectors. Despite this, at local level mining and quarrying are associated with both irreversible environmental damage and several visual alterations affecting the natural landscape. In this sense, SIA (Social Impact Assessment) has become a strategic tool that can not only improve the prediction but also the assessment of the social impact by involving the local communities in a participatory process. Taking into account the SIA experience, together with the examination of some relevant international case studies, it is possible to draw up a list of good practices for mining project management, from exploration through to closure and beyond, with quarry restoration. Such good practices will complement the existing studies, focusing on environmental issues, with the social issues arisen considered in SIA application."

Jan 1, 2011

By P Meehan, R McAree, Z Guan

Equipment maintenance is 30 - 50 per cent of the operating costs for a typical mining company. While this is substantial, its importance is beyond its significance as a cost heading. Modern mining requires large amounts of investment in capital infrastructure and equipment to produce a product sold at a low unit cost. To stay competitive, such a business has to focus on full realisation of its capital investment, ie sustained production at high levels. Maintenance plays an essential role in achieving this goal. Mining companies typically use a mix of breakdown or corrective maintenance, planned maintenance, and some condition-based maintenance. The share of breakdown maintenance has been coming down through more effective planned maintenance and better condition monitoring tools. Planned or preventive maintenance (PM) is playing an increasingly important role in todayÆs mining maintenance. This is the suite of inspection and repair/replacement actions performed at scheduled time intervals as part of a preplanned activity. The activities are scheduled well in advance and, usually, the current wear-state of the machine is irrelevant. For example, the replacement of a major gear may have been planned 18 months in advance; replacement is carried out when the time comes regardless of the actual condition of the gear. The PM costs are significant and include direct cost of parts and labour as well as the opportunity cost of lost production while the machine is under maintenance. It is important to identify the optimum PM effort because over-maintenance should be avoided as much as under-maintenance. A new concept called severity-based maintenance is introduced in this paper. We have seen that measuring equipment ageing in mining merely by counting the engine hours is a very imprecise way of planning and scheduling maintenance because the damage accumulated in one hour varies enormously from operator to operator and with changing pit conditions. We recommend continuous monitoring of duty on all major equipment. This is feasible without having to fit out the machine with an army of sensors because most of the physical sensors required by dutymeters are already installed and maintained as part of the existing performance monitors. While the investment is modest, the potential benefits are huge and can be grouped under three headings:Immediate benefits will come from providing operators with direct feedback on the effect of their behaviour on machine health and training them to use this feedback to correct their operating style. The equipment can operate closer to the limits of capacity, producing more without unduly sacrificing the availability by monitoring and controlling the severity of the operation, ie the duty on the machine. Longer term benefits accrue from establishing correlations between actual time to failure data and measured equipment duty and using these correlations to optimise maintenance effort as well as planning new equipment purchases and warranty conditions.

Jan 1, 2002

"The Detour Lake Mine is located in northeastern, Ontario, approximately 300 kilometres northest of Timmins and 185 kilometres by road northeast of Cochrane. The mill processes a free milling gold ore using both gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 mtpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The present paper will describe the methodology used to successfully prove that gold of the Detour Lake Mine ore is mostly concentrated into the fine size fraction of the blasted rocks. It will describe the various options possible to create value from this ore property.IntroductionThe purpose of this test work was to determine the grade of the pebbles and consider if there was value into discarding the pebbles and replacing the material by fresh feed.1. Pebble samplingThe pebbles were sampled and assayed for grade every day for 3 months. After 3 months of sampling, the results showed that the pebbles only carried 28% of the fresh feed grade. This phenomenon can possibly be explained by the fact the gold is located into area of fracture in the rocks.January-March 2014 – Pebble assay average• Line #1 = 0.222 g. Au/t• Line#2 = 0.275 g. Au/t• Head grade = 0.88 g. Au/t2. Crushing and grinding circuit surveysWith the above information, a grinding circuit survey was planned. The purpose of the survey was to build a JKSIMMET model of the grinding circuit for mill optimization but also to understand the deportment of gold into various size fractions that may explain why there is so little gold in the pebbles. All streams and size fractions was analysed for particle size analysis and for gold.Since Detour has dual grinding lines, both circuits were sample at the end of May. Two supplemental survey of the secondary crushers were also done and a survey of the gyratory crusher."

Jan 1, 2016

By M. Hooman, W. M. Marx, R. C. W. Webber-Youngman

This paper discusses a study that investigated different underground bulk air heat exchanger (>100 m3/s) design criteria. A literature review found that no single document exists covering all design criteria for different heat exchangers, and therefore the need was identified to generate a guideline with decision analyser steps to arrive at a technical specification. The study investigated the factors influencing heat exchanger designs (spray chambers, towers, and indirect-contact heat exchangers) and the technical requirements for each. The decision analysers can be used to generate optimized, user-friendly fit-for-purpose designs for bulk air heat exchangers (air cooler and heat rejection). The study was tested against a constructed air cooler and heat rejection unit at a copper mine1. It was concluded that the decision analysers were used successfully. This tool (decision analysers) can be used by engineers for the efficient and cost-effectively design of heat exchangers.

Jan 1, 2015

By R. S. Dewey

The purpose of this study was to assess the various aspects of public safety related to the thousands of abandoned or inactive underground mines found throughout Western Colorado. Review of available published mine inventories yielded data on over 8,000 abandoned underground mines. A random sample of 200 mines was then selected for field visits representative of mining activity in Colorado. Inspections of the openings at two hundred abandoned underground mines were performed recording descriptive information regarding the opening, the mine site, the surrounding area, the primary opening hazard, secondary hazards related to structures or dumps, other openings to the same mi ne, available construction materials, possible safeguard methods, and any special observations such as apparent activity, previous closure attempts, environmental constraints on construction, and access problems. Of the 200 mines visited, twenty mine openings representative of varying geologic, environ-mental, access, and mining conditions were selected for detailed low-cost safeguard application. Description of these safeguards is presented in narrative, itemized labor-materials equipment tabulations, and illustrations. Research into the regulations of mine closure and safeguards was also undertaken to determine jurisdiction of public lands. Recommendations were suggested to improve the awareness and ability to continue this program into an implementation stage.

Jan 1, 1980

Basic parameters affecting the stability of foams have been studied. We used the thin film pressure balance (TFPB) technique of Scheludko and Exerowa (1959) to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, MIBC, and PPG. The results were compared with the froth stabilities measured using the shake tests and the film elasticity calculated using the model developed by Wang and Yoon (2006). It was found that the froth stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother concentration and type.

Jan 1, 2006

By K. Schrijver, G. Beaudoin

"Four occurrences of galena-cemented sandstones, exposed in the Lower St. Lawrence - Gaspésie area, are described. They constitute a new, insufficiently explored type of deposit in Quebec.One mineralized body, a minor occurrence, is hosted in Lower Devonian rocks deposited in an estuarine, intertidal river channel during a marine regression; major cements are dolomite and sulphides. Another occurrence, a drilled prospect, is hosted in Upper Silurian rocks deposited unconformably on Cambro Ordovician basement during a marine transgression. With galena and quartz as main cementing minerals, it is similar to some well-known, economic sandstone-lead deposits. A third and fourth, a drilled prospect and a minor occurrence, are hosted in Upper Cambrian rocks deposited on continental slopes. In both, sulphides mainly occupy a secondary porosity. The differences between the third and fourth occurrences are: (1) cementing translucent minerals (carbonates and barite in one; chlorite in the other); (2) chronology of final subsurface dissolution (prior and subsequent to sulphide precipitation, respectively); and (3) important fracture porosity only in the barite-bearing deposit.The diversity of the four occurrences, and the unequal geological knowledge of their respective features, prohibit the formulation of uniform guidelines for further exploration.IntroductionThe attention of the mineral exploration community is drawn to four occurrences of galena-cemented sandstones (Fig. 2A) in the Cambrian of the Taconian Orogen and in the Siluro-Devonian basin of the Lower St. Lawrence and Gaspésie area (Fig. 1). In view of the fact that sandstone-lead deposits (Bjerlykke and Sangster, 1981) are, or have been, mined in several countries (e.g . Laisvall in Sweden: see Rickard et al., 1979; Largentiere in France: see Foglierini et al., 1980), the mere presence of occurrences in Quebec indicates that the mineral potential of some parts of the Appalachians requires further evaluation.Exploration for the deposits considered here is essentially restricted to geological methods and drilJing (e.g . Mainguet Suares and Samama, 1969), since the response to geophysical methods is virtually nil, at least in the initial, surficial stage of an exploration program. As the particular disciplines of geology utilized in exploration depend a great deal on the geological setting of a mineral occurrence, the diversity of the Quebec deposits is of prime importance. Therefore, the four occurrences (Fig. I, Table 1) studied by the authors are herein briefly described with emphasis on their stratigraphic and tectonic setting, and on the evolution of pore space and sequential occlusion of pores and fractures. Prior to further research in and around the occurrences, now in progress (e.g. Beaudoin, 1987; Beaudoin et al., 1987), it is hoped that the following outline will be useful to the explorationist."

Jan 1, 1987

By L. Lehasa

The purpose of the project was to investigate the challenges faced by Khutala Colliery pertaining to underground road construction and maintenance. Furthermore the influence of these challenges on productivity and safety requirements were taken into consideration. The operating standards required for the construction and maintenance of the 2 seam road transport infrastructure was investigated, together with reasons why the standards of operating procedure are not met. The Code of Practice put in place by Khutala Colliery was used to view the standard operating procedures. Leading practices on underground road construction were researched. The project aims to discover the gaps that Khutala Colliery must bridge to implement enhanced practices with regards to underground road construction. During the period of study, observations were carried out to determine whether the road construction standards of operating procedure were being adhered to at all times for both road construction and road maintenance. Khutala Colliery has put in place a traffic management plan, which includes safety practices and work policies that must be adhered to while travelling on underground transport roads.

Jan 1, 2012

By Stuart Brashear, Robert Brush, Ben Cook

In early 1993, the Piney River quarry owned and operated by the Blue Ridge Stone Corporation of W W? Boxley received a series of complaints from the owners of a 130 year-old historic farmhouse that had been converted into a bed and breakfast establishment. Since the distance from the quarry to the farmhouse was substantial, a unique method of seismic data acquisition was utilized to determine if perceived blast effects were caused by air blast or low amplitude, low frequency ground vibration.

Jan 1, 1996

By P E. H Gregg, R B. Stewart

Reclamation field trials commenced in 1985, two years before the granting of the Mining Licence. The level of pasture production on varying soil depths (0 cm, 5 cm, 15 cm and 25 cm) overlying both tailings and oxidised waste overburden was assessed.   After seven years, the rate of increase of N, C, P and S, losses of Sand P and pH changes were investigated on the plots where grass seed was sown into bare tailings. It was determined that on these plots it would take approximately 24 years to reach the original carbon and nitrogen levels at the mine site. Further tailings trials have been initiated to investigate alternative land use options for the tailings dam. Growth increases of 73% occurred in native species growing directly in tailings, and growth increases of 78% occurred in tailings amended with compost over the first six months. Pasture trials on tailings with and without a compost amendment have also been initiated. Research has commenced to investigate the restoration options for acid producing pit slopes. The early field trials have been put into practice with the restoration of oxidised waste on the tailings embankment. This is progressive with approximately 16 ha restored to productive pasture at present. Yields compare well with those of the most versatile and productive soils types investigated in baseline studies of the area before the tailings dam was constructed.

Jan 1, 1995

Pillars with width to height ratios of less than 1.0 are frequently created in underground hard rock mines. The strength of slender pillars can be estimated using empirically developed equations. However, the equations can provide variable results when the width-to-height ratios approach 0.5. This paper investigates some of the issues affecting pillar strength at low width-to-height ratios in hard brittle rock. The investigation includes an evaluation of empirical pillar strength data presented in the literature and observations of pillar performance in underground limestone mines in the eastern United States, supplemented by numerical modeling in which failure processes and sensitivity of slender pillars to variations in rock mass properties are evaluated. The results showed that the strength of slender pillars is more variable than that of wider pillars. The numerical model results demonstrated the increasing role of brittle rock failure in slender pillar strength. The absence of confinement in slender pillars can result in a fully brittle failure process, while wider pillars fail in a combined brittle and shearing mode. The onset of spalling in slender pillars occurs at or near the ultimate strength, while this is not the case for wider pillars. Slender pillars are shown to be more sensitive to the presence of discontinuities than wider pillars, which can partly explain the increased variability of slender pillar strength. Two examples are presented, which illustrate failure initiation by brittle spalling and the sensitivity of slender pillars to the presence of discontinuities.

By Karl Nienhaus

The BGMR has developed a method for an online-analysis during drilling processes in cooperation with Fraunhofer Institute for Laser Technology in Aachen and various industrial partners. This allows for efficient utilization of deposits, maximum recovery of desired minerals and frequent and costefficient updates of deposit models. The used method, namely laser-induced breakdown spectroscopy (LIBS), was implemented into a compact demonstrator in order to analyze drill dust and loosened material within mining environments and directly on drill rigs. The consequently developed OFURanalyzer (OFUR ? online-analysis of mineral deposits) provides possibilities for exploration and visualization of deposit models in real-time and thus creates an opportunity for innovative applications, such as contactless, continuous quality control of minerals throughout the extraction process. A major challenge in the execution of this project was the necessity to develop a laser system that could withstand rough mining environments dominated by dust, shocks, vibration and therefore would be suited to operate under such conditions.

Oct 1, 2009

By William C. McBee

Sulfur concretes have been developed by the Bureau of Mines as construction materials with physical and mechanical properties that suit them for use in acid and salt corrosive environments where conventional concretes fail. Mixture design methods were established for preparing sulfur concretes using different types of aggregates and recently developed mixed-modified sulfur cements Bench-scale testing of the sulfur concretes has shown their potential value. Corrosion resistance, strength, and durability of sulfur concrete are superior to those of conventional materials. Field in situ evaluation tests of the sulfur concretes as replacement for conventional concrete materials are in progress in corrosive areas of 24 commercial chemical, fertilizer, and metallurgical plants.

Jan 1, 1983

By Alok Garg, Rajeev Kumar Dayal

The Himalayan ranges have complex geological formation induced with locked up tectonic stresses and squeezing ground conditions. High overburden, steep slopes, perennial snow, and forest cover restricts accurate prediction of geological features, resulting in surprises during excavation. The tunnel planning under high altitude, extreme climatic, and unfavorable approachability conditions requires elaborate detailing. The construction technique and working faces for excavation are influenced by site accessibility/high overburden conditions, restricting the provision of access tunnel or shaft. The paper discusses site constraints influencing construction method and working faces for 8.9 km long highway tunnel at elevation 3,000 m under 1,900 mover burden through quartz-mica-schist formation.

Jan 1, 2001