Search Documents

By R. J. Kuczynski

The U.S. Bureau of Mines Reno Research Center operated a batch pilot plant to demonstrate high-temperature cyanide leaching for recovering platinum group metals (PGM) from automobile catalysts. Approximately 1,600 kg of used pellet, monolith, and metal support catalyst containing 1,680 g (54 tr oz) of PGM were processed. Forty-five-kilogram batches of used catalyst were leached with sodium cyanide solution at 160° C for 1 h under basic conditions in a countercurrent processing sequence to dissolve the PGM. Extractions from the used pellet catalyst ranged from 94 to 95 pct for Pd, 95 to 97 pct for Pt, and 64 to 81 pct for Rh. Extractions from the used monolith catalyst ranged from 7B to BB pct for Pd, 75 to 90 pct for Pt, and 43 to 71 pct for Rh. Heating the pregnant leach solutions to 275' C for 4 h destroyed the PGM-cyanide complexes, resulting in over 99.7 pct of the PGM precipitating from solution. The PGM precipitate was predominantly a powder metallic concentrate, typically analyzing greater than 50 pct PGM. Heating destroyed cyanide to less than 0.2 mg/L. Both the pellet and monolith residues were evaluated for disposal using the EPA Toxicity Characteristic Leaching Procedure.

Jan 1, 1995

By G. Fazel Jahromi

Enargite, known as one of the major arsenic containing copper minerals, with approximately 19% arsenic, introduces challenges to typical processing options. In most hydrometallurgical processing methods, arsenic remediation occurs after the copper recovery in an autoclave or in a stepwise neutralization process. In this study, the in situ precipitation of scorodite was investigated during an atmospheric leaching process in the presence of carbon-based catalysts and chloride media. The effective parameters of initial ferric addition, temperature, catalyst addition, and oxygen sparging rate were studied and the ferric behaviour was monitored during the scorodite precipitation. The most influential parameters on efficient scorodite precipitation are found to be: initial ferric addition, catalyst to concentrate ratio, and temperature. A 99% scorodite precipitation yield was achieved in this process.

By J. S. Becker

Technology developed and first implemented in the United Kingdom enables very low grade aluminum scraps containing oils, organics, plastics and ferrous metals to be directly charged, without pretreatment, into a unique melting furnace. The system has been in full scale production for four years. The oxy-fuel-based furnace design incorporates internal afterburning in the furnace's hot zone, producing excellent thermal efficiency and very low emissions. The furnace is inherently low in NOx. This paper will provide both theoretical background and extensive operating results for this new melting concept. Applications describing both purpose built new furnaces and retrofits of existing reverberatory furnaces will be presented. Extensive operating emissions data will be presented.

Jan 1, 1997

By Lifeng Zhang

Printed circuited boards contain considerable quantities of valuable metal, while also containing many environmental pollutants making them unsuitable for landfill. In this study the decomposition of common plastics used in printed circuit boards were studied. Polytetrafluoroethylene (PTFE), polyvinyl chloride (PVC) and polyethylene (PE) were heated in both C02 and argon atmospheres using a thermo-gravimetric furnace (TG) coupled to a mass spectrometer (MS). Soda ash Na2C03 and baking soda NaHC03 were used as reactants. The degradation temperatures and evolved gases are presented for single plastics and mixtures. Mixed plastics are shown to behave as a sum of the individual plastics. The mass loss temperature is the same in CO2 and argon. However, less residue is formed when heated in CO2.

Jan 1, 2008

By G. Upadhya

Of late, solidification modeling has progressed considerably to emerge as a viable simulation tool for the foundry engineer. A wide variety of tools exist in the commercial market to cater to the various needs of the design/ foundry engineer. In fact, recent developments in the area of solidification modeling have been so rapid that a comprehensive review of the state-of-the-art is very much needed. In this paper, an attempt is made to summarize the various issues of solidification modeling, at the same time addressing the historical evolution of the subject. The various phenomenological issues covered in this paper include: heat transfer, fluid flow during mold-filling, solidification kinetics and microstructural evolution, quick-analysis schemes for approximations, porosity prediction models, and the phenomena of fluid flow in the mushy zone. Modeling issues related to the development of solidification stresses which lead to defects such as hot tears and the development of artificial intelligence concepts in the area of rigging design are also discussed. Due emphasis is given to the various phenomena which add to the complexity of the whole subject, and the various alternatives available for solving a particular problem. For example, the heat transfer problem can be approached by the use of simple modulus schemes or by solving the conduction equation to obtain a more accurate temperature distribution. Similarly the microstructural evolution can be handled in a deterministic way by use of nucleation and growth models, or in a probabilistic way by use of empirical models. The main goal of this paper is to put the multi-faceted problem of solidification modeling in proper perspective so that it can serve as a guide for future developments in this area.

Jan 1, 1994

By Shigehito Deki

"A new wet process has been developed for the synthesis of various kinds of oxide thin films on various kinds of substrates, even which have complex surface morphology, from aqueous solution. The process was named as the LPD, Liquid Phase Deposition, method, which has some advantages over the conventional dry processes. This process can be applied to an on-site synthesis of advanced materials in the thin film technology. In this paper, some current topics on the synthesis of the composite thin oxide films by the LPD method, are presented.IntroductionGenerally, metal oxide thin films have been made by different preparative processes such as r.f. sputtering, chemical vapor depositon, CVD, laser ablation and sol-gel method, etc [1-3]. Each method has it own advantages and disadvantage. In some cases, the process is not suitable for the preparation of thin film on substrate with large surface area or complex surface morphology, and makes the deposition apparatus complicated and expenisve. By using Liquid Phase Deposition, LPD, method which overcomes some of those problems, metal oxide or hydroxide thin film can be formed on the substrate with large surface area and complex surface morphology, which are immersed into the aqueous solution only at ambient temperature and under atmosphere without any special equipments and high energy. And also, multicomponent oxide thin films can be formed readily by mixing solutions containing the objective metal ions, because it is performed in the aqueous solution which is typically a homogeneous mixing system. This process utilizes ligand-exchange, hydrolysis, equlibrium reaction of metal-fluoro complex species, MF x (x-2n>-, and F consumptive reaction. In the aqueous solution, MFx<x-2n>-is hydrolyzed with water to release F ions by a ligand exchange equilibrium reaction as following;"

Jan 1, 2000

By D. Majuste

This paper describes an experimental approach to evaluate the effect of organic impurities or even additives on metal electrowinning and product quality. In addition to electrowinning tests and electrochemical measurements, the approach includes organic analysis by Fourier Transform Infrared spectroscopy and gas chromatography; video monitoring of the reaction interface; and product characterization by using scanning electron microscopy, crystallographic texture and bending tests. The mechanical behavior of metal cathodes was assessed with a customized bending device that is able to bend the cathodes up to angles similar to that of the stripping machine. In this work, the effect of a potential organic impurity, lubricating oil, on the production of electrolytic zinc is taken as a case study. The findings of the investigation allowed a better understanding on the role of this organic on energy consumption and product quality and a qualitative prediction for the behavior of Zn cathodes during the stripping operation. Simple control and optimization procedures resulted in significant energy savings.

By Djalma Souza, Jean Igor Margem, Sergio N. Monteiro, Frederico M. Margem

Synthetic fibers have been used for many years to attend the demands required by the technologica lfields. However, the use of them has been questioned due to the impact on the environment. In this way, the natural fibers have received extensive attention, in particular hybrid fabrics of natural fibers to reinforce environmentally friendly polymer matrix composites. Thus, the present work has the objective of evaluating and comparing the mechanical properties of composites formed by hybrid fabric with 70% Malva—30% Jute in epoxy polymer matrix. The tests carried out are the Charpy and Izod Impact Tests, with specimens of 10, 20 and 30% in volume of hybrid fabric environmentally friendly into polymer matrix composites at room temperature. The 30% samples had the best results, functioning as an efficient reinforcement.

Mar 1, 2018

By Bingguo Liu, Daifu Huang, Jinhui Peng

"The conditions to prepare U3O8 by calcination from ammonium diuranate were optimized, and the response surface design method was applied to analyze the influence on the total uranium and U+4 of calcination temperature, calcination time and mass of sample. A quadratic equation model for the total uranium and U+4 of U3O8 was built and the effects of main factors and their corresponding relationships were obtained. The analysis of variance shows that calcination temperature and calcination time significantly affected the value of total uranium and U+4 of U3O8. The optimal calcination conditions were as follows: calcination temperature 931.83 K, calcination time 24.32 min and 43.89 g. Under these conditions the value of total uranium and U+4 of U3O8 was 84.78% and 28.02%, respectively. The validity of the model was confirmed experimentally and the results were satisfactory.IntroductionNuclear energy is clean, effective, and a sustainable from of energy. It plays an important role in overcoming the impending global energy crisis, and in reducing energy vulnerability. In addition, nuclear energy is a possible cheaper and cleaner source of energy compared to fossil fuels, with no not really, mining of uranium produces CO2 contribution to green house gases [1]. Uranium dioxide, one of the most important fuel pellets used as nuclear fuel in light water reactors, is manufactured by calcining ammonium diuranate to triuranium octaoxide, followed by its reduction to uranium dioxide using cracked ammonia at 700°C [2]. Earlier attempts to optimize the important calcination process through several common techniques have not yielded desirable results [3]. These techniques either rely on the classical one parameter at a time approach that ignores the combined interactions between physicochemical parameters, or are theoretical in nature. Furthermore, these techniques also require large number of experimental data to be generated [4]. In order to produce triuranium octaoxide in an optimized manner, which considers the interaction of different process parameters [5], there is a need to adopt a multivariate statistical technique."

Jan 1, 2011

By K. R. Robilliard

Ausmelt Technology has been developed to process copper concentrates containing significant levels of lead, arsenic and antimony. A process was developed aimed at smelting these concentrate materials to remove the contaminants to fume and produce a clean copper product. The production of clean copper and the potential economic benefits of this process step over the sale of impure concentrates is discussed.

Jan 1, 1995

By David Van Aken, Arpana S. Murthy, Simon Lekakh, Von L. Richards

"Three heats of 17-4PH stainless steel: with zero, three percent, and seven percent cobalt addition were melted in a 45kg (1 00lb) induction furnace under argon; and cast into no-bake molds and preheated investment shell molds. Specimens were sealed into quartz tubes under vacuum, and homogenized at 1200°C from 2h to 72h. Computational thermodynamics and optical microscopy were used to predict and characterize the microstructures. The lath martensite packet size and the amount of 8-ferrite were observed to be inversely related. A compromise between decrease in segregation and increase in lath martensite packet size was chosen for the optimum homogenization treatment. The specimens were austenitized, quenched, and characterized for retained austenite using x-ray diffraction. Age hardening kinetics were studied at 454°C (850°F), 468°C (875°F), and 482°C (900°F); and, the activation energies for precipitation of copper were calculated. Tensile properties and Charpy V-notch impact energies were measured in the peak aged condition. Fracture surfaces were observed using scanning electron microscopy and Energy Dispersive Spectroscopy. The addition of cobalt was found to be beneficial for the improvement of strength as well as notch toughness.IntroductionSegregation in the as-cast condition is one of the drawbacks of metal casting. This paper presents a study on the homogenization treatment of 17-4 PH cast stainless steel and the effect of cobalt addition on tensile properties and Charpy V-notch toughness. Lattice dilatation studies show that additions of up to 6% Co to iron has a negligible effect on the lattice parameter, whereas both the modulus of elasticity and shear modulus increase with increasing cobalt additions5• An ordering reaction has been reported in cobalt-containing, maraging steels and contributes to the hardening during ageing1-4• Although, cobalt addition in maraging steels has been extensively researched, and has been reported to be beneficial; it has not been explored much in other age-hardening stainless steel systems. In a previous study, the addition of 3% Co in cast 17-4 PH martensitic age-hardenable steel was found to improve the strength and elongation while maintaining the charpy V-notch toughness6."

Jan 1, 2011

By Huaqing Xie, Qingbo Yu, Qin Qin

A novel sorption-enhanced steam reforming (SESR) process of hot coke oven gas (HCOG) was proposed for tar removal and H2 amplification, and was studied with the comparison of conventional steam reforming (SCR) process. Both of the processes could remove tar effectively and improve the H2 amount in the COG obviously. For CSR process, after the temperature and the S/HCOG ratio reached 700 °C and 2.4 respectively, the H2 amplification factor kept 4.30 around, with its concentration less than 75%. However, for SESR process, the H2 amount and concentration get improved further, with the optimal temperature moving toward low temperature. At 600 °C and the S/HCOG ratio of 2.4, the H2 amplification factor and concentration could reach 4.91 and 97.55% respectively when the CaO/C ratio was 2.0. Under the respective optimal reforming conditions of the two processes, the energy consumption of the SESR process was lower than that of CSR process.

Mar 1, 2018

By Xuewei Lv, Yuelin Qin, Guibao Qiu, Chenguang Bai

"Blast furnace slag (BF slag), is the main by-product in the ironmaking process, which contains large amounts of sensible heat. To recover the sensible heat, this paper described the hot experiments which were carried out in a rotary multi-nozzles cup atomizer, where the molten BFS was transformed into granules without water impingement; subsequently, a new method-pyrolysis the printed circuited board (PCB) with the hot BFS particle, was proposed for recovering the sensible heat in this study. The gaseous products were analyzed by gas analyzer. The residual of the PCB was analyzed by FT-IR and XRD respectively, and the obtained slag particles were analyzed by XRD.The results showed that it is a feasible process of pyrolyzing PCB powder with the hot BFS particle. The sensible heat of hot BF slag could be converted to chemical heat and a large amount of combustible gas could also be generated during the process.IntroductionDue to the rising of the product cost of blast furnace iron (BFI) and the increasing public awareness of environmental problems, the steel industries have to focus on the energy saving and emission reduction. Blast furnace slag (BF slag) is a byproduct from blast furnace exhaust temperature of 1450°C or so, is a high-quality waste heat resources. In China, the steel industry produces approximately 220Mt ofBFS per year, and the enthalpy of those slags is approximately equivalent to 13.3% of the whole energy consumption in the ironmaking process[!]. It can be seen, recycling waste heat is an important way of energy saving for iron and steel enterprises. The molten slag was treated by conventional water quenching method without any recovery of heat in spite of its huge potential. Also, the water quenching process consumes a plenty of water, pollutes the air and water[2]. Additionally, the extra energy is necessary for the drying process of slag to produce cement. As a kind of secondhand resource which can be reused, the BF slag contains a large amount of sensible heat. To recover the sensible heat of BF slag, three key problems should be considered, which refer to ( 1) the dry granulation of BFS without consuming water, (2) how to recover the heat of slag particles efficiently, (3) how to use the slag particles after heat recovery."

Jan 1, 2012

By Chris Doyle

From 1997-2000. PT INCO undertook the Fourth Line Expansion Project (FLEX) to increase annual production rates from 90-100 to 150 Mlbs Ni/year (68,000 MT Ni/yr). In 2003, PT INCO nickel production underwent a major sustainable step jump that finally exceeded the targeted rate. This paper presents the changes that led to this achievement. The focus of mining changed. Improving Ni grade was important but only if electric furnace feed met target chemistry so that on-specification slag could be produced. The intensity of diamond core drilling for exploration was dramatically upgraded, mine planning strategy was totally re- vamped and an ore chemistry quality assurance team was formed. In the processing plant, measurement systems were upgraded for better control. Teamwork between sections vastly improved. The final step jump in production occurred when the fifth hydro-electric power generator was added to the furnace grid to allow the power-starved furnaces to cruise in operation at 70+ MW. Keywords: Free cash flow, Ore Chemistry, Measure, Control, Improve

Jan 1, 2004

By Beatryz C. Mendes, Henrique de Paula Santos, Kléos M. L. Cesar, Eduardo Antônio G. Marques, Maurício Paulo F. Fontes, Rita de Cássia S. S. Alvarenga

Inadequate discard of industrial solid waste is a risk to human health and to the environment. Aiming at softening environmental damage caused by deposition on soil of an ink residue, from washing of printers used in carton box packages, it is intended to incorporate this residue into soil-cement bricks. The residue has other use potentialities such as in screeds, pavement parts, fertilizer, paints, etc. However, to explore these potentialities it is fundamental to assess the risks that the several forms of use of this residue can cause. For such, in this work the chemical analysis of the residue was performed in order to know its main chemical compounds, in addition to its characteristics of leaching and solubilization. The chemical composition assay showed traces of some heavy metals such as Pb, Cd, Cr, Zn, Al and Cu, although the residue-generating company uses ink labeled as heavy metals free. Among the elements analyzed in leaching and solubilization, some had concentration above the limit allowed by The Brazilian Codes. This code is based on CFR—Title 40—Protection of Environment—Part 260–265—Harzardous waste management. Therefore, it is suggested that the residue has a limited use to avoid contamination of ground water.

Mar 1, 2017

By Juha Järvi

Outokumpu Zinc Oy has two separate roasting lines with fluidized bed furnaces and waste heat boilers for calcine collection and heat recovery. During the last 30 years, zinc production in Kokkola plant has increased continuously and at the same time the raw materials have changed. Therefore, the waste heat boiler has been under continuous research and development. The waste heat boiler plays a significant role in the process and consequently the reliability and efficiency of the device is important for the effectiveness of the entire process. Many changes have been made to the boiler in the last decades. New radiation tube screens, tube bundles, and baffle-plate constructions have been added to the boiler and also rapping systems for the dust have been developed. The latest improvement to the boilers was a baffle wall, located in the middle of the radiation section roof in the first boiler, and baffle plates in the lower part of the convection section in the second boiler. The new boiler design and optimization were carried out using physical water and air-dust modeling as well as computational fluid dynamics. The modeling work agrees well with experiences in practice. The latest developments have increased the operating hours per year and the effectiveness of the waste heat boiler.

Jan 1, 2002

By Rodney Hundermark, July Ndlovu, Lloyd Nelson, Phillimon Mukumbe, Paul van Manen, Whitey Seyanund, Bart Pieterse, Bertus de Villiers, Diale Mokwena

The 2003 redoubling in power to 68MW on the Polokwane Smelter furnace represented a significant intensification in platinum group metal (PGM) smelting. Combined with onerous ‘green’ PGM concentrate smelting requirements, this yielded conditions unusually corrosive to copper coolers and refractories. This presented unexpected operational and design challenges to reliable crucible operation and maintenance. Combined with specific operational control intervention, development of protective coatings has led to the life of water-cooled copper components improving from 9 to 40 months. The furnace matte endwall was extended in 2010 to address accelerated wear of refractories and the potential risk for contact of copper components by superheated matte. An 18 month planned endwall rebuild cycle has been demonstrated (versus catastrophic failure within 9 months). Finally, benefits including lower energy consumption, improved metal recoveries and higher productivity resulting from operational and in-house design developments will be described, that justify “Celebrating the Mega-scale” in PGM smelting.

Jan 1, 2014

By Mansoor Barati, Shaghayegh Esfahani

"The slag from extraction of ferrous and non-ferrous metals is a potential heat source which if treated properly can contribute to recovery of a significant amount of energy. The waste heat of slag may be used to generate steam, synthetic fuel gas, or electricity. Although several technologies have been investigated for this purpose, very little has been achieved in terms implementing the technology in industry. In this article, the development and application of various granulation techniques are reviewed and the methods to recover energy from granulated slag are discussed.IntroductionEvery year, more than 422 million tons of slag is being produced around the world as a by-product of the metal manufacturing at temperatures of up to 1300-1600°C [1, 2]. Currently slags are either disposed of or treated by processes such as granulation. Through the granulation process, most slags can be converted into a material which may be fully used as a cement feedstock. Conventional cement production is an energy intensive process with large emissions of CO2; therefore, the replacement can both be energy saving and environmentally friendly. However, for this purpose, the slag should have what is known as a “glassy” content (i.e. it should be amorphous) which requires rapid cooling rates that are not easily achieved due to the very low thermal conductivity. The main challenge in all these processes is to granulate the slag at a high cooling rate while the heat is also being recovered."

Jan 1, 2012

By Lloyd R. Nelson

Selective carbothermic reduction is the preferred method of treatment of electric arc furnace (EAF) dust (listed hazardous waste, K061). The process maximizes the recovery of recyclable constituents by concurrent production of saleable zinc metal (directly condensed from the furnace off-gases), an innocuous, disposable iron oxide-rich slag, and some metallic iron. Results of a mineralogical investigation of a foaming slag produced during selective carbothermic reduction treatment of EAF dusts are presented. Wiistite and tricalcium silicate were identified by reflected light microscopy as the primary crystalline phases contained in a glassy matrix, but this technique failed to reveal any solid phases that could have significantly contributed to foam stability. It was concluded therefore, that the foam had been unstable, and had been primarily generated by copious gas evolution associated with the sudden reduction of the slag by an inadvertent addition of carbonaceous reductant. This is consistent with the susceptibility to foaming, when subjected to sudden excesses of carbon, of the slags produced by selective carbothermic reduction, because they still contain unreduced components such as iron oxide.

Jan 1, 1994

By Malti Goel

"The cost-effective capture of carbon dioxide (CO2) from the point sources for its reduction the atmosphere offers many challenges in materials science. Novel CO2 capturing approaches using chemical, physical and biological methods are in the research stage and are aimed to minimize the cost. Appropriate materials development , which can withstand required temperature or pressure as the case may be for CO2 emanating from coal gas or industrial waste gases form the minimum condition. Other requirements are reclyclability of material and cost of separation. Nano-material composites can be more effective in selective capture of CO2 and can offer solutions for large-scale separation process. Nano-porous material catalysis can enhance the reaction rate of CO2 with other chemicals and thus help in capture of CO2 and convert it into value added products. This paper reviews recent industrial scale developments. In the Indian context, R&D priority areas in CO2 capture process development with a focus on energy industry are presented.IntroductionScience of Climate Change is growing at an enormous pace. With the ultimate goal of stabilization of greenhouse gases in the atmosphere, new scientific approaches are being researched worldwide. A shift in policies from low carbon and no carbon energy sources to fossil fuel sources with capture of carbon and its permanent storage is taking place. The process of carbon capture is both energy and materials intensive and the cost of power generation may increase up to 40% when carbon capture and storage (CCS) technology is implemented. Development of cost effective R&D technology therefore remains the greatest challenge before the scientific community."

Jan 1, 2009