Search Documents

By Y. Pokhvisnev, S. Vandariev, A. Yatshenko-Juk, V. Valavin, V. Romenets

The technology of the liquid-phase reduction process known as Romelt was developed in the Moscow Institute of Steel and Alloys in 1979. The pilot plant was constructed at the Novolipetsky Steel Works (Russia) in 1984. Investigations into processing zinc-containing blast oxygen furnace dust and slag from the Lead and Zinc Works at the pilot Romelt plant proved the perspective of using this technology for processing zinc and lead-containing materials. In this article, the description of Romelt technology, basic technological information of trials at the Romelt plant using zinc-containing materials, compositions of charging materials, metal, slag, gas and dust are presented. The influence of flue gas composition on the composition of zinccontaining dust is shown.

Jan 1, 2000

By Xiang-dong XING, Zhen-yang wang, Xing-le LIU, Jian-Liang Zhang

Experiments were carried out by adding CaF2 as catalyst in a Ar atmosphere to study the isothermal reduction kinetics of vanadium titano-magnetite carbon composite pellets under high temperature in the range from1473 to 1673K. By analyzing reduction mechanism, it was found that the rate controlling step was gas diffusion, and the activation energy was 178.39kJ•mol-1 without adding any catalysts. Adding CaF2 of 3% to vanadium titano-magnetite carbon composite pellets can decrease the apparent activation energy of reduction, and the decrease extent was 14.95kJ•mol-1. In addition, temperature is an important factor influencing on reaction rate.

Jan 1, 2015

By W. S. Kirk

World cobalt production in 1987 was estimated to be about 26,600 metric tons (MT) of which Market Economy Country (MEC) production was estimated to be about 22,000 MT. Zaire and Zambia produce about 80 percent of the primary cobalt produced among Market Economy Countries (MEC). Production cutbacks. lowering cobalt grades and mining curtailments in Finland and Zambia in 1987, resulted in lower production than that of 1986. The trend is expected to continue through 1988. Cobalt production from Canadian ores and from Botswana is expected to increase significantly in 1988 as a result of increased nickel production. MEC production in 1988 is estimated to be 22,100 MT, only slightly higher than that of 1987. There are currently no primary cobalt mines. Virtually all cobalt is recovered as a byproduct of copper and/or nickel mining. Zaire, which produces cobalt as a byproduct of copper, is the worlds largest cobalt producer, with over 50 percent of total estimated world cobalt production and nearly 65 percent of MEC production. Zambia follows with about 14 percent and 17 percent, respectively. Zambia's cobalt production also results from copper production.

Jan 1, 1988

By Ana E. Bohé, Fabiola J. Alvarez

"The separation of nickel from the aluminum present in spent catalysts and different metallic industrial residues, is proposed in the following systems: alloy Al2Ni and the mixtures 50 wt% Ni + 50 wt% Al, 10 wt% Ni + 90 wt% Al2O3 and 12 wt% NiO + 88 wt% Al2O3. The experiments were carried out in a tubular reactor with a flow of 2 l/h of gaseous chlorine and from 200 ° to 800 °C. The final products of the reaction, extracted from the hottest zones of the reactor where characterized by XRD, SEM, EDS, AA and XRF, as NiCl2 y NiCl2.6H2O while in the coldest regions AlCl3 was deposited in the first two cases and in the other there was a residue of ?, a- Al2O3, sometimes mixed with some remainder of Ni and NiO. The procedure attained different separation factors which showed the optimun conditions for the recovery of both metals. Introduction Some studies of nickel corrosion were carried out in chlorine gas at temperatures above 950ºC, and suggested that nickel is not corroded below 538ºC. [1] However, in a previous work it was shown that the chlorination allows the separation of nickel from aluminum and the formation of NiCl2 was detected from 200ºC in binary mixtures Ni-Al 50 wt%, for isothermal conditions in chlorine flux. [2] Other researchers obtained selective chlorination above 650ºC of a fly ash containing 1.4 wt% of Ni and other metals (V, Mg, Al and Fe). The Ni was separated from the Mg and NiCl2 started to vaporize at 550ºC and was after condensed in a zone of the reactor above 380ºC with 90% of purity. [3]"

Jan 1, 2008

By Yotamu Hara, Animesh Jha

"High Curie temperature and large magnetic anisotropy make cobalt an important magnetic material for power engineering applications of magnets operating above ambient. It is also an essential constituent of modem lithium - cobalt oxide batteries, without which modem electronic gadgets will be functionless. Both these applications of cobalt save energy and reduce C02 emission. Ironically, however the production of cobalt from copper and nickel smelting in the world remains one of the least energy efficient process. The paper analyzes the energy balance, material and process chemistry of overall cobalt recovery and the waste generated, which entail the process limitations. We discuss a novel approach for the reduction of sulphide minerals with CaS04, permitting better separation of metals from slag and generating higher concentrations of S02. Such an approach may seem to be an alternative energy efficient option for processing and further purification of cobalt in metallic form. The results are discussed in the context of process thermodynamics and reaction kinetics for Coalloy production.IntroductionCopper sulphides bearing minerals are predominantly associated with iron and cobalt sulphides minerals. Carrollite (CuC02S4) is a mineral that has both copper and cobalt sulphides [1,2], which may also contain FeS, by substituting either Cu2+ or Co2+ ions in mineral lattice. On smelting copper - cobalt - iron sulphide concentrates, some parts of the cobalt often partition to matte at preferentially low oxygen potential by forming eventually an alloy phase with copper, however a significant fraction is often lost into an oxide slag rich in iron and silica. The slag heaps accumulated in the Copperbelt region in Zambia from last 60 years of mineral processing and metal extraction is reported to be 0.3 to 2.6 wt% of cobalt element, which is high [3]. Cobalt is also available in smaller concentrations in the copper smelting and converter slag, as reported in the investigations on the recycling of such slag materials using leaching with ammonium salt [4], iron chloride [5], and sulphuric acid [6], and solvent extraction [7].The recovery of cobalt from slag, irrespective of the techniques researched so far, does not seem energy efficient because the molten slag at 1300°C is quenched by losing thermal and chemical energy. The quenched slag is again reheated to above room temperature for leaching and above liquidus for carbothermic reduction of residual cobalt oxide. For example, in Mintek DC arc smelting [3], 80% of cobalt and 95% nickel are recovered by expending 600 kW per tonne. Assuming that the mineral carrollite is the starting phase, the univariant calculations for the Co-Ca-Si-S-0, Fe-Ca-Si-S-0, and Co-C-Si-S-0 systems are shown in Figure la, lb, and le, respectively at 1573 K."

Jan 1, 2012

By Qiu Dingfan

The Slurry Electrowinning Process (SEP) is a new hydrometallurgical method and clean technology, Sulfide ores can be treated by the SEP without S02 emission and the sulfur from the sulfides can be recovered in element form which is easy to stockpile and can be transported at low cost. In a special slurry electrowinning cell one can achieve at the same time the leaching of elements from the feed and the electrowinning of metals from the electrolyte, Because the anode reactions are utilized for leaching of some elements the consumption of the energy is decreased, SEP also has the advantage of separation some elements, It is especially suitable for treatment of complex concentrates containing Pb, Cu, Au, Ag and S, which could hardly be accepted by any smelter. In this work, the behavior of different metals in this process has been studied and it was found that the separation of metals in some minerals is possible through the SEP, Beijing General Research Institute of Mining and Metallurgy (BGRIMM) has studied the possibility of the SEP to treat bismuth concentrates containing S, Be and F in laboratory and pilot-test scale as well as in commercial plants, The commercial plant was set up in 1997, It has been in operation since that time, According to the results of laboratory experiments and pilot- plant test, a new plant to treat complex gold minerals was set up in 1998 and is in operation in 1999

Jan 1, 2003

By G. G. Krishna Murthy

Several experiments were carried out to simulate the bath smelting reactions where iron oxide particles were dropped on to an iron-carbon bath containing molten CaO-SiO2-Al2O3 slag layer on its surface. The composition of the slags used in the experiments was %CaO:46.1; %SiO2:41.7; and %A1203:12.2. Experiments were con¬ducted with carbon saturated iron melts contained in either a pure graphite crucible whose walls were covered with a pure alumina tube, or a pure flat bottom alumina crucible, at 1723-1823 K. Degree of reduction of a pure iron oxide particle was linear with time in the initial stages (up to about 20% oxygen of the original pellet was reduced). The rate of reduction of smaller oxide pellets was smaller than that of a bigger pellet - the time for complete reduction of a 5.6 g wustite pellet was smaller than that for a 1.2 g wustite pellet. It was also established that the interaction rates obtained by adding a molten pure oxide particle of given weight to the system were lower than that determined by using a solid oxide particle of same weight. The overall rates of reduction decreased with decreasing the bath temperature. The experimentally determined rates of reduction based on the time for 70% reduction were influenced substantially by addition of slag up to about 50 g on to a bath of 78.8 mm in diameter, and remained constant when slag present on the bath surface was between 50 g and 200 g.

Jan 1, 1993

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"In the present study classical induction design tools are applied to the problem of heating nonmagnetic metal billets, using 50 Hz AC. As an example of great practical industrial interest, the induction heating of aluminum billets is addressed specifically. The predicted work piece power is compared with the measured work piece power for a long and a short coil, using well established methods, such as those of Burch and Davis, introduced in 1926/28, Dwight and Bagai in 1935, Baker in 1944/57, Vaughan and Williamson in 1945, and by Tudbury in 1960. A calculation methodology based on a combination of the available tools is also introduced and discussed. The method has proven to give an error of <10% of the actual work piece power. An equation for Tudbury's work piece shortness correction factor is disclosed for the first time.IntroductionInduction heating of metal billets is a practical problem, with a geometry suitable for solution using analytical methods. This paper will examine solutions related specifically to round work pieces in round coils, although the methods presented can be extended to other regular shapes of work pieces and coils[l]. The methods can also be extended to ferromagnetic materials with slight changes[2-3]. It is assumed that the coil and work piece have a consistent diameter over their entire length and that the work piece is at least as long as the coil. Correction factors can be derived for the cases where the work piece is shorter than the coil.The study of induction heating by coils began in the late 19th century with theoreticians like Heaviside[ 4]. The work of Burch and Davis[ 5-7] in the 1920' s greatly improved the theoretical understanding of induction applied to metallurgy. Many investigators in the 1930's-1950's: Dwight and Bagai[8], Baker[l-2, 9], Vaughan and Williamson[3, 10] and others[l 1-12] added to our understanding with clearer mathematics, solutions for specific applications, semi-empirical modifications and practical design tools. Much of the accumulated knowledge is available in books, such as Tudbury's practical text or Simpson's engineering guide from 1960[13-14]. Perhaps the best description and derivation of the theoretical and semi-empirical solutions can be found in Davies[15]."

Jan 1, 2011

By H. H. Kellogg

The Process Fuel Equivalent (PFE) for nine different flowsheets for production of anode copper from sulfide concentrates has been evaluated and compared for a set of uniform conditions and a "standard" concentrate analysis. The processes considered are: reverberatory smelting, (wet-charge and hot-calcine charge), electric furnace smelting, Outokumpu flash smelting (2 versions), mom flash smelting, Noranda Continuous Process (2 versions), and the Mitsubishi Continuous Process. The energy required for the numerous processes auxiliary to the principal smelting processes-¬roasting, drying, air compression, gas handling, dust collection, slag cleaning, acid manufacture, etc.--are separately evaluated and incor¬porated into the process comparisons. The factors in process design that lead to important energy savings are: use of fuel rather than electric energy; use of oil or coal rather than natural gas; maximum use of oxygen enrichment of the process air; drying of charge before smelting, or, even better, drying and preheating of charge by partial roasting in a fluid-bed; recovery of waste heat from all major hot process gases.

Jan 1, 1976

By Jian Li, Tiejun Chun, Jian Pan, Deqing Zhu, Vinicius Mendes

"A study of the coal-based direct reduction behaviors of composite binder magnetite pellets was carried out in a simulating coal-based grate-rotary kiln process. It is shown that preheated pellets possess much better reducibility than fired oxide pellets: 40 min are required for preheated pellets to reach over 90% metallization degree compared to 100 min for fired oxide pellets. The compressive strength of preheated pellets decreases dramatically at the earlier stage of reduction, climbs quickly after reducing for 30min and achieves a high value at the end of reduction. However, the compressive strength of metallized pellets from reducing of fired pellets is much lower, more cracks and fractures being formed. In the preheated pellets, crystallite of metal iron is coarse. In the oxide pellet, a large number of interconnected crystals of metal iron are formed inside pellets, and pellet structure is very compact.IntroductionDirectly reduced iron is an excellent feed in electric arc furnace (EAF) steelmaking, and possesses low tramp element content and steady component. It is generally preferred in the production of high quality steel [1-3]. Nearly 64.44 million tons of DRI were produced in 2009 over the world, over 80% of which were produced by gas-based processes, the left by coal-based processes. However, the DRI capacity was only 600 thousand tons in China in 2009. The EAF steel production has exceeded 40 million tons annually, and most of EAF operate on hot metal as feed [4]."

Jan 1, 2011

By Yoichi Takeda

The CaO-FeOx-Cu20 slag has been practically applied to continuous converting of copper, and also has potential for refining of copper. Liquidus lines of the slag system and phase stability diagram for the liquid slag and the existing solid compounds under copper saturation are presented. Liquidus composition was determined by chemical analysis of slag sample saturated primary solid. The temperatures of invariant equilibria were investigated by thermal analyses. Oxygen potentials on the liquidus lines, the univariant and invariant equilibria were estimated from the relation slag composition and oxygen potential that relation was confirmed in separate experiments.

Jan 1, 2003

By Yoichi Takeda

The CaO-FeO,-Cu20 slag has been practically applied to continuous converting of copper, and also has potential for refining of copper. Liquidus lines of the slag system and phase stability diagram for the liquid slag and the existing solid compounds under copper saturation are presented. Liquidus composition was determined by chemical analysis of slag sample saturated primary solid. The temperatures of invariant equilibria were investigated by thermal analyses. Oxygen potentials on the liquidus lines, the univariant and invariant equilibria were estimated from the relation slag composition and oxygen potential that relation was confirmed in separate experiments.

Jan 1, 2003

By Filippos Patsiogiannis

Laboratory size (5 kg) aluminum killed low carbon steel melts were desulfurized with synthetic fluxes in zirconia crucibles. The sulfur, oxygen, aluminum, silicon, and manganese contents in the melt were determined as a function of refining time and temperature. With a good argon shield and synthetic flux cover, melt reoxidation was not observed. Sulfur removal followed first order reaction kinetics. The effectiveness of calcia saturated calcium-aluminate (12CaO.7Al2O3) based fluxes in desulfurizing the steel melts was evaluated. The effects of initial sulfur level of the melt, weight of the flux (slag), and additions of tellurium, fluorspar, and barium oxide to the melt on the kinetics of desulfurization were also studied.

Jan 1, 1993

By A. A. EI-Geassy

High-grade iron ore fines rejected from the DRI plants (>96%Fe2O3) were isothermally reduced in 30-60%CO/H2 gas mixtures at 973-1273K. The freshly reduced reaction products were then subsequently carburised in either Hz/CO or H2/CO/S mixtures at 823-1 073K for 30-120 min. The thermogarvimetric technique was used to follow up both of reduction and carburisation reactions as a function of time. The carburised samples were characterized by X-ray and Mossbauer techniques. Chemical and carbon analyses were also applied. The influence of temperature and gas composition on the reduction behavior was investigated. The calculated values of apparent activation energy, application of gas-solid mathematical formulations were correlated with the microstructures to predict the reduetion mechanism. The influenee of carburization time, temperature, CO contents in H2/CO or H2/CO/S were investigated. A conversion extent of Fe to Fe3C was taken as a measurable index for the efficiency of carburization rcaction under the different experimental conditions.

Jan 1, 2003

By Manjie Li, Mingrui Yang, Haijun Peng, Shuxing Qiu, Wei Liu, Shengfu Zhang

It is important to produce and utilize highly reactive coke in order to reduce the energy consumption and CO2 emissions through improving shaft efficiency in blast furnace. The present study aimed to investigate the transformation of iron minerals and properties of iron coke (the coke mixed iron ore fines). Along with the increase of iron ore fines, cold strength displayed a slight downtrend and the pore structure wasn’t inferred to be a major factor affected the properties of iron coke. During carbonization, the majority of mixed iron oxides were reduced to metallic iron by CO and H2 and the degree of metallization achieved to approximately 75%. Nevertheless, produced metallic iron was oxidized by pure CO2 during gasification. Iron coke reactivity index (ICRI) was obviously enhanced and the iron coke strength after reaction (ICSR) drastically decreases, which were also significantly influenced by crystal structure of carbon.

Jan 1, 2015

By K. J. Martchek

"This introductory presentation will highlight recent efforts to quantify the positive value of recycling metals such as aluminum, magnesium, lead, zinc, nickel and copper in relation to the three pillars of ""sustainable development"" - environmental protection, economic development and improve social consequences.This presentation will provide an overview of life cycle assessment profiles increasingly being utilized by customers, regulators and environmental advocacy groups to holistically evaluate the environmental performance of materials and products. The environmental profiles of prodi.lcts containing recycled metal will be presented based on rules established by the International Organization for Standardization (ISO).Significant to the life cycle profile of metal products is recent confirmation. that recycling has the potential to reduce materials production energy consumption by 95% for aluminum, 80""/o for magnesium and lead, 75% for zinc, and 70% for copper. Furthermore, . ""metals are eminently and repeatedly recyclable, while maintaining all their properties (1 ). "" Their durability relative to many hydrocarbon based materials enhance .their life cycle performance. However, the persistence of metals when dispersed into our natural environmental makes recovery and recycling particularly important Overall, when considering life cycle effects, recycling is critical to a sustainable future for metal products.Finally, regional and international regulations will be highlighted which will effect the efficient recovery and recycle of metals and their overall contribution to environinental protection, economic development and the enhancement of society."

Jan 1, 2000

By J. H. Puffer

The copper mineralization of the Mesozoic Passaic Formation of New Jersey is typical of copper deposits in eastern North American Mesozoic sediments. Most such deposits are located at the base of the first of several basalt flows that are interbedded with continental, red-bed sediments. The copper mineralization is similar in most respects to that of the Keweenawan Basalts of the Lake Superior area. The first basaltic flow units of the eastern North American Mesozoic basins, and the Keweenawan Basalts, are continental quartz tholeiites of similar chemical composition and copper contents. The copper minerals and associated zeolite facies metamorphic mineral assemblages of these two rock units are also approximately the same. Stoiber and Davidson (1959) suggested that Keweenawan copper was mobilized and concentrated during metamorphism. The evidence pertaining to the Mesozoic copper deposits of New Jersey is consistent with such an interpretation and also with DeVore&apos;s (1955) suggestion that ore fluids commonly arise as a result of the mobility of metals under metamorphic conditions. There is additional evidence that final metamorphic concentration of Mesozoic copper was preceded by an initial stage of hydrothermal precipitation related to fluids emitted by basaltic magma.

Jan 1, 1987

By L. A. Mills

After three years of experience in operating the pilot plant for the Noranda Continuous Smelting Process, the decision was made, in March 1971, to build an 800 ton per day commercial plant at Noranda, Quebec. The de- sign and layout of the plant is discussed and the installed equipment described. Experience previously gained in the pilot plant is mentioned when it has been used in the choice of equipment or plant layout. The full- scale reactor was started up in March 1973 and the operational datacollected and the experience acquired during the first 30 months of operation are described. This includes operation to produce both high grade matte and copper. Areas discussed include refractory wear, fuel consumption and throughput of copper concentrates. Changes made to original equipment and methods of operation are discussed, together with the reasons. The ad- vantages of using solid fuels to handle inert materials and to maximize converting air flowrates and concentrate throughputs are described. Relative efficiencies of oil and natural gas are compared. The addition of oxygen from a 94 ton per day oxygen plant to the reactor converting air was started in August 1975 and the initial operating results are included.

Jan 1, 1976

By Minh H. Pham

This paper presents a technique for imaging the extent of solidification of molten metal flowing in a cooled pipe based on the concept of eddy currents. A 3D mathematical model, which relates the geometry of solidification to the scattered field induced in a solenoid external to the pipe, is derived. The model is described by a set of integral equations which are solved numerically using the moments method. An iterative algorithm is developed to reconstruct the solidification distribution image. Experimental measurements have shown that the eddy current technique is sufficiently sensitive for practical purposes.

Jan 1, 2001

By V. I. Lakshmanan

The demand for elements such as nickel, cobalt, titanium and gold in various applications has increased significantly. Innovation to recover these elements now plays a major role in metallurgical processes as established technologies have challenges in treating the types of ores that are available while meeting the increasingly stricter environmental regulations. Alternative chloride based processes have been developed that can be used to recover the value elements from the available feed stocks with potentially lower environmental impact. Chloride-based hydrometallurgical processes have several advantages, including higher leachability of complex ores/tailings and relative stability of chloro-complexes of the metals. Process Research ORTECH Inc. (PRO) has developed mixed-chloride process flowsheets, where innovative solvent extraction process steps are used for the separation of nickel, cobalt, titanium and gold from their respective chloride solutions. This paper will discuss the potential aqueous chloro-chemistry of these metals and separation reaction mechanisms involved in the solvent extraction process.