Search Documents

By Joner Oliveira Alves

The aim of this work was to study the use of steelmaking slag as raw material to the production of rock wool and glass wool. Firstly, the chemical composition of the slag was analyzed. These results were used to infer the amount of additives to assemble the charge for the experiments. A laboratory-scale electric furnace was used to melt the mixtures used as charge. The melt material were turned into a water filled recipient, this process was performed in order to impose a fast freezing that is a characteristic of mineral wool production. Finally, with the rest of the melt material it was performed the Herty Viscosity Test. Samples of the produced material were characterized by different analyses. The results found in this research may lead to a technological innovation, because they indicate that the use of steelmaking slag to produce rock wool and glass wool is possible.

Jan 1, 2009

By Emma Arakelova

?2?2 (98 %) vapour passed through a reactor at 25Pa where a Zn? target was placed at 273K- 373?. Experiments were carried out on a flow- type vacuum device. ?2?2 decomposition on Zn? surface accompanied by formation of a Zn-containing volatile complex which transferred to the gas phase, and Zn? deposited on a substrate at condensation. As the substrate, five sequentially located quartz cylinders were used at 293K- 423 K (?n). Decomposition of the Zn-containing complex on quartz substrates carried out as a first- order reaction. ?The complex decomposition constant (??) increased with the substrate temperature (?n=293 K, ??=7.05 sec-1;?n = 373 K, ?? = 87 sec-1;?n = 423 K, ?? =158 sec-1). ?The complex decomposition constant did not practically vary when the target temperature increased; the complex formation rate increased slightly.

Jan 1, 2006

By Sergio N. Monteiro

Wastes generated by our society and the question on how to dispose them is, nowadays, a relevant matter of concern. The objective of the present work was to characterize the technical properties of composites made of discarded jute sackcloth with its coarse wove fabric, serving as reinforcement phase, and polyethylene wastes collected from city dumps, as continuous matrix. Different amounts, up to 30 wt.% of jute plain weave, fabric were press molded at 160°Ctogether with sieved polyethylene particles. The resulting composites displayed mechanical properties that could compete with those of low-density wooden board. Both by presenting a solution to, otherwise, disposed wastes and by helping to prevent deforestation, the investigated composite may be regarded as an environmentally correct material.

Jan 1, 2006

By Yunnen Chen

In the present study, waste materials like pine sawdust and spent grains were investigated to assess their potential for removal of cobalt ion from water by the process of biosorption. The effects of solution pH, reaction time and initial concentration were studied in batch experiments. The removal efficiency of Co(? ) by spent grains was higher than that of pine sawdust. The initial removal was rapid and equilibrium was established in less than 90 min. Equilibrium data all agreed well with both Langmuir and Freundlich isotherm models for the two metal-biomass sorption processes. Good correlation coefficients were obtained for the pseudo second-order kinetic model. Pine sawdust and spent grains were shown to be promising biosorbents for Co(? ) removal from aqueous solutions.

Jan 1, 2010

By José Carlos D?Abreu

The Tecnored process is a new ironmaking technology, developed on a unique approach that combined empirical and theoretical knowledge backed by extensive tests carried out in a dedicated pilot-plant and with close support of universities and research centers. Campaigns in the pilot-plant focused on operate different reactors of different sizes, including a full size slice of the industrial furnace. This approach provided actual conditions to develop the main features of the process such as the internal dimensions, raceway pattern, thermal and gaseous profiles, etc, besides provide reliable data to feed and calibrate a specific mathematical process modeling. This paper presents the first computer model used by the Tecnored technical staff, focusing the behavior of a self reducing agglomerate in the upper shaft of the furnace (zone of solid state reduction). Some results of this model are given and discussed.

Jan 1, 2006

By J. C. Pandey

The paper highlights the experimental investigations to characterize texture and plastic strain ratio r-Bar in auto grade steel sheets by ultrasonic measurements, whereas attempts were made to characterize interlamellar spacings in pearlite, tensile stresses and torsional properties in prestressed concrete wires by eddy current measurements. Good correlations were obtained between the testing parameters (such as ultrasonic attenuation and velocity in case of steel sheets as well as eddy current out put voltage and phase angle in case of steel wires) and the materials properties (such as texture, plastic strain ratio r-Bar, interlamellar spacings in pearlite, tensile stresses and torsional properties). 15 MHz normal direct contact and 20 MHz delay line normal shear wave probes were used for ultrasonic measurements. Eddy current measurements were done using an absolute coil probe with variable frequency selection. The experimental results show the possibility of nondestructive on line measurement of the above microstructures and properties.

Jan 1, 2010

By Jeffrey D. Winterton

Keywords: Copper, ion exchange, sulfonic acid, bis-picolylamine, ion exchange modeling, ion exchange kinetics As part of an investigation into the feasibility of using ion exchange resins to recover copper from aqueous waste streams generated during the manufacturing of semiconductor devices, the uptake of copper onto two ion exchange resins was investigated. The resins studied were DOWEX G-26, a standard gel type sulfonic acid resin, and DOWEX M4195, a macroporous chelating resin with a bis-picolylamine functional group. The equilibrium and kinetic behavior of the uptake of copper were investigated over a range of copper concentrations with constant sulfate concentration and different levels of acidity. The homogeneous structure of the G-26 resin yields equilibrium relationships that fit the Langmuir equation, and equilibration times of less than 30 minutes. The uptake behavior of M4195 is complicated by the need to absorb co-ions to maintain electroneutrality, resulting in uptake profiles that change character with increasing copper concentrations, and extended equilibration times.

Jan 1, 2005

By Keith S. McIntosh

The fire assay process for the quantitative recovery of platinum group elements (PGE?s) prior to subsequent analysis traditionally is a time-consuming process. Samples derive from various ore types and contain PGE?s at the ppm or ppb levels, making concentration of the elements mandatory before assaying. Traditionally sample turn-around times are of the order of 24 hours. The whole sequence of sample preparation, fire assay and subsequent analysis of PGE?s have been automated by Anglo Platinum. Some of the major challenges on the road to automation will be discussed and the novel solutions that were implemented. The engineered solution included robotic automation of the whole sequence, from sample preparation, up to the final element by element assay. The final system allowed for rapid (less than one hour) and accurate analysis of PGE?s even in streams containing very low levels, such as flotation tailing streams and drill core samples.

Jan 1, 2006

By H. Doostmohammadi

During the tapping of liquid steel from Electric Arc Furnace (EAF), some slag is carried over into the ladle. High levels of FeO and MnO in slag carryover increase the oxygen activity in steel melt leading to oxide inclusion formation during the ladle treatment. The demand on cleaner steels requires minimization of carryover slag. In this work, the effect of EAF slag carryover on ladle slag-steel equilibrium calculations for a hot working tool steel was studied. Steel and slag sampling were done in Uddeholm Tooling AB in Sweden. XRF and OES techniques were used to determine chemical composition of samples. The quantity of slag carryover was calculated based on a mass balance followed by thermodynamic calculations on metal-slag equilibrium using Thermo-Calc software. The agreement between predictions and experimentally determined compositions was good. This leads to the development of a prediction method for optimizing the production of other tool steel grades.

Jan 1, 2009

By Chang-Dong Li

Cadmium ingot and nickel powder were prepared by high-temperature distillation, solvent extraction and liquid phase reducing method with spent Cd-Ni batteries as raw material. The impacts of the temperature in the distilling stage, the concentration of H2SO4 in the leaching stage, the pH value in the extracting stage and the dosage of hydrazine in the reducing stage were discussed respectively. The as- prepared samples were characterized by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic absorption spectrometry (AAS) and inductively coupled plasma-atomic emission spectrometry (ICP-AES). The results showed that the recovering efficiencies of Cd and Ni reach 99.5% and 99.3%, and the purities of Cd ingot and nickel powder were higher than 99.90% and 99.80%, respectively.

Jan 1, 2009

By Hong Yong Sohn

Keywords: Barium sulfate, Barium sulfide, Environment, Kinetics, Pollutants, Sulfur dioxide conversion, Thermodynamics Nonferrous smelters and coal gasification processes generate sulfur dioxide streams, most of which are treated to produce sulfuric acid with the accompanying problems of market shortage and transportation difficulties. While the conversion of sulfur dioxide to elemental sulfur has many environmental advantages, no processes exist that are environmentally acceptable and economically viable. A method for converting sulfur dioxide to elemental sulfur by a cyclic process involving calcium or barium sulfide and calcium or barium sulfate without generating solid wastes has been developed. In this process, the sulfate, as the starting raw material, is reduced by a suitable reducing agent such as hydrogen to produce the sulfide, which is used to reduce sulfur dioxide producing elemental sulfur vapor and regenerating the sulfate. The latter is then reduced to reproduce the sulfide. This paper describes work on the BaS/BaSO4 system. Thermodynamic analysis and experimental results indicated that the BaS-SO2 reaction produces mainly sulfur vapor and solid barium sulfate and that the gaseous product from the BaSO4-H2 reaction is mainly water vapor. The rates of the two reactions are reasonably rapid in the temperature range 700-1050°C.

Jan 1, 2005

Sm-Co alloy is a kind of magnetic material with high power and has been applied in modern industry widely. In this study, the wet chemical co-precipitation was developed for synthesis of the Sm-Co alloy oxide precursor. The thermodynamic analysis of the studied system was done to clarify the solution behavior theoretically based on the thermodynamic equilibrium and simultaneous equilibrium. Then, the experiments were done to address the various effects on the wet chemical process, including solution pH, reactant concentration, dispersant, reaction temperature and time, etc. It is found that by precise control of the process, the Sm-Co alloy oxide precursor was synthesized with fine crystallization and special size & size distribution.

Jan 1, 2005

By Hui Lu

The structural changes in solutionized AA2618 during natural aging and their effects on subsequent artificial aging were investigated by hardness measurements, X-ray diffraction, differential scanning calorimetry and transmission electron microscopy. The changes in lattice parameter and hardness during natural aging indicate that copper-enriched clusters form in the earliest stage, followed by the formation of magnesium-enriched clusters and coppermagnesium co-clusters. Prior natural aging consistently weakened the hardening during subsequent artificial aging at 180, 200 and 230 °C but had no effects on artificial aging at 150 °C. The decreased age hardening was attributed to the reversion of small clusters/zones that formed during prior natural aging. The lattice parameter exhibited erratic changes with increasing artificial aging time, reflecting the complex sequence of the reversion and precipitation.

Jan 1, 2006

By Hirokazu Narita

Keywords: solvent extraction, precious metals, thiodiglycolamide, rapid separation, hydrochloric acid The solvent extraction of some precious metals (Pd(II), Pt(IV), Rh(III) and Au(III)) and base metals (Fe(III), Cu(II) and Zn(II)) in a hydrochloric acid solution was carried out using N,N'-dimethyl-N,N'-dioctyl-thiodiglycolamide (MOTDA) dissolved in the mixed solution of 80 vol-% dodecane and 20 vol-% 2-ethylhexanol. The extraction percentages of Pd(II) and Au(III) in the 0.01 M MOTDA-1.0 M HCl solution system are 99.6% and 71.8%, respectively. In contrast, the other metal ions are hardly extracted under the studied conditions. The Au(III) and Pd(II) extracted in the organic phase are easily back-extracted with a 1.0 M thiourea/1.0 M HCl solution. A comparison with the conventional extractant for the Pd(II) separation, di-n-hexyl sulfide (DHS), revealed that the extraction rate of Pd(II) with MOTDA is much greater than that with DHS. The extraction percentage reached over 99% in less than a 2 min contact time. However, in the DHS-Pd(II) system, it takes about 240 min to achieve the extraction equilibrium. Furthermore, MOTDA can quantitatively extract Pd(II) up to half the molar amount of MOTDA. Therefore, MOTDA is a promising extractant for Pd(II) from the HCl solution after the removal of Au(III).

Jan 1, 2005

By Qingzhu Li

The brewing industry byproduct, spent grain (SG), was evaluated for its ability to adsorb Ag(I) from aqueous solutions. Ag(I) adsorption was dependent on solution pH, contact time, adsorbent dose, initial Ag(I) concentration and temperature. The kinetic data were well described by pseudo-second-order kinetic model, indicating that chemical adsorption was the rate-controlling step. The equilibrium data followed Freundlich isotherm rather than Langmuir isotherm, suggesting heterogenity of the adsorption sites on spent grain. Ag(I) desorbed from Ag(I)-loaded spent grain was also evaluated in this study. HCl, NaOH, Na2S2O3 and ultrapure water were chosen as eluants and desorbed Ag(I)-loaded spent grain for 30min, Ag(I)-loaded spent grain desorbed in 0.1M Na2S2O3 exhibited higher elution efficiency as compared with other eluants. The results indicated that application of spent grain for adsorption and recovery of silver from aqueous solutions was feasible.

Jan 1, 2009

By Carlos Maurício Fontes Vieira

In the present work a ceramic body, fabricated using a mixture of clays and sand, for roofing tiles, produced in Campos dos Goytacazes, north of the State of Rio de Janeiro in Brazil, was characterized. Characterization was performed by X-ray diffraction, thermo analysis, chemical analysis, particle size distribution determination and plasticity. In addition, technological properties related to water absorption, linear shrinkage and flexural rupture strength were determined in samples fired at 700, 900 and 1100oC. The results showed that the investigated ceramic body has satisfactory plasticity and presents a refractory behavior during firing due to the predominantly kaolinitic nature of the clays.

Jan 1, 2006

By Carlos Frias

The lead-acid battery recycling is a major industrial activity (more than four million tonnes recycled lead per year) that generates large amounts of toxic wastes such as lead slag, mattes and acidic sludge, besides airborne emissions. This is a waste-producer industry that needs a definitive solution to avoid its negative environmental impact and getting a sustainable lead production. That is the principal target of the CLEANLEAD technology, which properly combines both hydrometallurgical and pyrometallurgical routes aiming to get zero-waste production, reducing the use of energy and resources in all phases of battery reprocessing, and consequently, greatly decreasing the operating cost. There will be no toxic emissions to land, water or air, and obtained products are pure lead metal or pure lead oxide, and commercial gypsum instead of waste sludge.

Jan 1, 2006

By Theo Lehner

Turning matte into anodes continues to be an area to watch: for visitors to see pyrometallurgy in action; for metallurgists to keep up with modern smelting furnaces and ever increasing production rates; for management to remain profitable using more tools than taught in school; and for environmentalists to detect the last small clouds from the ever cleaner smelter. Current converting practices have been screened and analyzed, and today, converting and casting is a modern industry. An impressive, though typical learning curve of converter productivity may be detected. Local conditions such as availability and type of raw materials, products extracted, cost factors, etc., have stimulated the development of add-ons or even alternatives to the still dominant method of converting by Peirce-Smith technology. Turning blister copper into anodes follows a similar path, namely increased productivity and improved quality. We dare to predict that development will continue.

Jan 1, 2005

By Mark C. L. Patterson

Hydrothermal brines are extracted from significant depths below the surface of the earth and arrive at the surface at elevated pressure and temperature. The exact chemistry and conditions of these brines depends upon the rock formations through which the water travels, but many of the brines are rich in dissolved minerals especially silica which is often saturated in the brine. At pressure and temperature the minerals remain in solution but in order to extract heat from the brines, they need to be cooled and during which many of the minerals precipitate causing problems. Where precipitation is a problem in the downstream processing, the brines are maintained at a high enough temperature and pressure so as to avoid precipitation and injected back into the geothermal formation. This results in a significant loss in potential energy that could be recovered from the geothermal brines. If left to precipitate in an uncontrolled manner, many of the minerals will precipitate as gels, in a high surface area form which is difficult to extract from the liquor and which can causes problems. Precipitation in this manner often builds up on the inside of pipes, reducing the pipe cross-section available for fluid flow and reducing the overall efficiency of the plant. If the brines are seeded at the appropriate time or the precipitation conditions are changed, mineral particles can be grown and separated more easily from the brine. During this precipitation and growth phase the chemistry of the local environment can also be altered to grow more valuable particulates. Some of the specific chemistries will be discussed with reference to known geothermal brines and what needs to be done to precipitate value added products. A theoretical approach to the complete extraction of minerals from geothermal brines is also discussed with the goal of extracting more heat from the brine prior to reinjection into the well.

Jan 1, 2006

By Xiang Sun

Microwave heating has been used in numerous industrial processes due to its great advantages when compared with conventional heating methods. However, microwave heated products can be affected by non-uniform temperature distribution resulting from the mechanisms of microwave heating. To overcome this problem, a critical step is to have a temperature-time profile. In order to characterize and evaluate microwave heating effects, an accurate temperature measurement is needed. This paper discusses the possibility of applying several temperature measurement techniques in microwave processing. Both contact and non-contact methods are introduced and compared.

Jan 1, 2006