Search Documents

By Francis Kendorski

A longwall coal mine in Appalachia about 1,500 ft deep encountered a fault while developing a new longwall panel. The fault extended from mining depth to the surface near a secondary road and drainage. The fault was located inside the anticipated angle of draw within the mined panel and gob. The fault extended vertically out and up, away from the panel, caved zone, and gob at nearly the angle of draw: the fault very nearly following the angle of draw. It was initially thought that "fault reactivation" could possibly occur. Fault reactivation is the phenomenon of having mining subsidence localized along a fault leading to a "reactivation" of the fault and shearing and displacement along the fault. Such fault reactivation would disrupt and deform the fault plane beyond the normal angle of influence of the subsidence trough, and may provide a conduit for any ground and surface waters to reach the mine. We contacted all operators of longwall mines in Appalachia to determine if any Appalachian longwall mines had ever experienced fault reactivation, and teamed that none had experienced the phenomenon. After studies of possible water intrusion quantities and rates based upon in-fault pump tests, which indicated that water intrusion rates should be manageable, and the prior experience that faults in this particular area were usually barriers to water flow, mining proceeded with caution and monitoring. Mining was successful with no noticeable increase in water inflow rates, and no measurable off-setting of the fault exposure on the surface. It can be concluded that the fault did not reactivate due to its relationship to the mining sequence.

Jan 1, 2003

By Stephen C. Tadolini

The U.S. Bureau of Mines (USBM) is conducting research to provide alternatives for traditional secondary support methods. These cost-saving methods are proving to afford safer installation, improve entry stability, eradicate material-handling injuries associated with crib supports, and enhance ventilation. In cooperation with Mountain Coal Company, the USBM replaced timber cribbing with high- strength cable supports to provide stability in a gate road that was used for two longwall panels. The support design consisted of 2.1-m (7-ft) full-column resin-grouted bolts and 4.8-m- (16-ft-) long high-strength resin-grouted cable supports. Three support concepts were evaluated: passive, stiff, and tensioned systems. Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during panel extraction. The stress and loading histories for both panels and the abutment and yield pillars were monitored to assist in evaluating the stress transfer and pillar performance in conjunction with the roof behavior. The test results indicated that resin- grouted cable support systems successfully maintained the immediate and main roofs during the extraction of two longwall panels. This paper describes the theory, application, and advantages of resin-grouted cable supports and presents the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1994

By Mictck Rataj

Methods of rock reinforcement in Australian coal mines are being advanced progressively through the better understanding of rock failure mechanisms around roadways and the-development of improved bolting hardware and installation techniques. It has been recognised that to improve the performance of rock reinforcement systems, the stiffness of the system as a whole has to be improved. New style bolts and accessories together with high pre-tensioned roof and cable bolts are being developed as a result. A number of the new techniques used to stabilise the roof, especially in weak roof/high horizontal stress areas have been site proven and are now currently used on a routine basis as a means of improving development rates and gate road stability during longwall retreat.

Jan 1, 1997

By Zach G. Agioutantis

The prediction of ground movements due to underground mining using the influence function method is a mature technology, widely used by researchers and planning engineers around the world. Surface strain, either tensile or compressive, is an important indicator of potential impacts on structures such as buildings, bodies of water, pipelines, railway and power lines, and tailings dams. Calculation of static or dynamic surface strains, for varying surface terrains and slopes, should be accurately predicted and be independent of the methodology applied for the calculation. This paper discusses and compares the development of horizontal and ground strains on the surface due to underground mining for different surface topologies (sloping terrain, monitoring lines, etc.) and presents the steps needed to ensure accurate calculations. Examples are given to demonstrate how ground strains can be calculated for one- and two-dimensional gridded surfaces.

Jan 1, 2013

By Nathaniel Schaefer, Christopher Newman, Zach Agioutantis

"As mining reserves continue to be developed in deeper and more complex geological and geometric conditions, there has been an increased demand for underground mine designs to better reflect site-specific conditions, measurements, and observations with respect to ground control safety and stability. Current ground control design software are limited to a given device and data files generated can only contain a single design. However, with the growth of cloud computing and increases in internet access, even underground where permissible, web-based software applications allow for in-the-field calculations, as well as collaborations, from multiple users. webGroundControl (webGC) utilizes a multiple-tier architecture, building upon existing NIOSH ground control design software, more specifically ARBS, ALPS, and ARMPS. By providing operators the ability to access ground control design programs from any device, given an internet connection, webGC allows for on demand calculations to ensure underground pillar and roof stabilities with respect to current site-specific parameters, geometries, and geology. Through the development of new features, which aid in design analyses, as well as project collaborations, webGC provides the modern engineer with a more versatile ground control design tool for the improvement of underground health and safety. With the completion of the ARBS, ALPS, and ARMPS modules, this paper introduces potential users within the mining industry to the navigation and operation of the webGC application, as well as its ability to facilitate collaborations between operational personnel and planning engineers. The purpose of this paper is to raise interest in the web-based application before its official launch in Summer 2018."

Jan 1, 2017

By Ken W. Mills

The ground movements associated with underground coal mining and, in particular, longwall mining, are recognised to include horizontal subsidence movements, but the mechanics of the processes that cause these horizontal movements are not well understood. Over the last two decades, three-dimensional subsidence monitoring has become routine in Australia and has provided a wealth of measurements of horizontal movements caused by mining subsidence. These measurements and other sub-surface observations allow the processes that cause mining-induced horizontal movements to be inferred and, subsequently, verified. In this paper, the mechanics of the processes that cause horizontal movements, particularly those in sloping topography, are described and discussed on the basis of field observations. There are several processes recognised to generate horizontal subsidence movements. In flat terrain, systematic horizontal movements cause the surface to move initially toward the newly created goaf and, subsequently, in the direction of mining. Tectonic energy stored as horizontal stress is released by mining, and, when the horizontal stresses are high, the magnitude of this horizontal stress relief movement is large enough to be perceptible for some kilometres from the panel. In sloping terrain, there is an additional component of horizontal movement that occurs in a down slope direction. This movement, sometimes referred to as valley closure movement, has a magnitude that is typically much greater than systematic or stress relief movements.

Jan 1, 2014

By David A. Newman

Strength and physical property testing of coal is conducted regularly by the Arch Mineral Corporation as part of reserve exploration. Pillar design and mine layout are the primary applications for the coal strength data. Distinct differences in pillar behavior were observed during longwall mining at a mine in Southeastern Kentucky. Horizontal and vertical variation in both triaxial and uniaxial compressive strength was observed within the four (4) benches of the Harlan seam. Similarly, geographical variations in coal strength were noted across the Harlan seam reserve. During the past three decades substantial research efforts have been focused upon coal pillar behavior and the refinement of pillar design methodologies. Ironically, little attention was directed to integrating the variability of coal strength into pillar design. The authors examine, through the presentation of case history data, i) typical industrial practice with respect to establishing a database of coal strength for use in pillar design and stability analysis, ii) approaches in which the observed variation in strength in the Harlan seam is integrated into pillar design and stability analyses, and to iii) propose standards for coal cube testing

Jan 1, 1993

By Yanfa Gao

Clusters of underground openings were developed around the shaft bottom of Tangshan Mine. They were deep and located in soft rock strata. After development, those openings have been subjected to considerable deformation and damages. A combined supporting method including grouting and bolting, shotcrete lining and brickwork was used. This paper analyzing the theories on which this supporting method was based. A new theory called "Disturbed Creep" was developed for deformation prediction of openings surrounded by strata subjected to stresses close to limiting or failure strength. Keywords ground pressure, deep mine, soft rock, stability control

Jan 1, 2002

By Hani Mitri

A new monitoring device called SAFEBOLT (Stress And Force Evaluator in Bolts) has been recently developed. The device SAFEBOLT, essentially replaces the load cell, it permits the monitoring of bolt axial load from the time of its installation underground. The SAFEBOLT system consists of a portable readout unit, connecting cable and the SAFEBOLT device, which is installed in the bolt head. SAFEBOLT can be installed on any industry standard rockbolt. No special installation method is required; the conventional method of bolt installation by the stoper or roofbolter remains unchanged. The device is completely encapsulated in the bolt head, which makes it resistant to corrosion, rugged, and free of any electrical wires. Pilot tests at three underground Quebec mines were carried out and helped improve the initial design of the device connector. The paper reports on two of such pilot tests.

Jan 1, 2001

By Yanfa Gao

Abstract In order to control and reduce ground subsidence due to coal mining, and to protect building, railway and other surface construction, a new subsidence control method is proposed. Ground subsidence is reduced by grouting bed separations in overlying strata with fine-coal ash. Engineering application tests have been performed for 5 years in Tangshan Coal Mine. Kailuan Group Corporation. China. The technology has been applied to 4 fully mechanized sublevel caving mining faces. Its effect in reducing subsidence has been significant. The technology including grouting engineering design method and ground subsidence prediction theory is introduced in detail. Keywords: overlying strata separation, multi-layer grouting, subsidence control

Jan 1, 2002

By Timothy Batchler

"Standing roof supports help to provide a stable working environment in coal mine gateroads. NIOSH participates in the development of these support systems by conducting full-scale tests in their Mine Roof Simulator. These tests have established the performance characteristics of every coal mine support system currently in use in the United States. Through these tests, mine operators and regulatory officials have acquired a fundamental understanding of the various types of support performance that guides the assessment and use of these support systems. However, some little known factors that influence support behavior can lead to misconceptions and, perhaps, a poor assessment of support behavior at times. This paper highlights several of these factors and discusses their significance. The paper also examines a current longwall tailgate support and discusses the inefficiency with this approach. Finally, the NIOSH Mine Roof Simulator (MRS) is the world’s most powerful load frame built specifically to test full-scale roof supports, including longwall shields. are addressed in this paper to provide a more in-depth assessment of the limitations of the MRS and what the MRS testing protocol is designed to do. INTRODUCTION Over the years, considerable research has been conducted to develop standing support technologies and to evaluate their performance characteristics. The load and displacement characteristics of the standing supports have been determined from full-scale testing conducted using the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) (Barczak and Tadolini, 2008) located in Bruceton, PA. Performance traits, installation patterns, and ground responses are observed in various geological and mining conditions and are evaluated to determine the support performance in the field (Dolinar, 2010; Campoli, 2015; Zhang et al., 2012). Despite widespread use of standing supports, not every aspect of their performance and resulting ground support capability are always well understood. This paper discusses 10 factors, several of which are surprising, that impact standing support performance."

Jan 1, 2017

By Rajendra Singh

In India, pillar mining is contributing more than 90% of underground production which involves extraction of a part of coal from bords with pillars around as natural support in the development stage. #Liquidation of these pillars with splitting and stooking, broken nature of face during mining under complex geomining factors like massive roof, varying treatment of goaf and over or underlying workings result in high stresses and deformation in and around the neighbouring piilars, causing operational problem and hazards to mine safety. This paper suminarises the results of three case studies of depillaring under shallow depth with or without stowing. Assessment of nature and amount of mining induced stresses and deformation was done under these conditions, by insitu instrumentation and observation at three depillaring panels of Girmint. Samla and Lachhipur collieries of ECC at 54, 90 and 110 m depth cover respectively. The value of induced stresses and associated deformations was comparatively low in well caved and stowed waves, whereas for massive roof the roof fall followed overriding of pillars and stooks, with very high value of induced stresses and deformaton in absence of stowing. The stress in the centre and outer edges of the pillars changed with respect to depillaring face advance or splitting of pillars. The caving panel of Girmint colliery under weak coal measure formation, showed maximum induced stress in the pillar at 4 m distance from the face which was 1.2 times (16.6 kg/sq.cm) the preminlng stress of the area. The main roof fall over partially stowed goaf of Lachhipur colliery under massive roof strata caused overriding of pillar after crushing 39 stooks of 7.5 x 7.5 sq.m in rythmic sequence with development of 133lsq.cm maximum induced stress. Well stowed Waf of the same panel reduced this value of abutment stress to 2.3 times (65 kg/sq.cm.) body stress after 40 m further advance of the face from the crushed zone. The depillaring at Samla colliery even under massive roof strata induced low stress, equal to 0.8 times field stress only under the same condition with stowed goaf. The studies revealed the effectiveness of stowing in the goaf over loading of pillars and stooks.

Jan 1, 1990

By Rossen A. Halatchev

This study introduces a new probabilistic approach to seismic stability analysis of embankments and slopes. The approach is based on Sarma's solution, which is modified through presentation of the seismic force by its horizontal and vertical components; i.e. the force may have an arbitrary inclination. The probabilistic modelling includes Monte Carlo simulation of the shear strength parameters of the soil mass, which are assumed to have a normal distribution. The probability of failure is determined based on the seismic co-efficient, which is treated as a random quantity. The probabilistic approach is illustrated through a solution of a numerical example from an opencast coal mine.

Jan 1, 1992

By Markus Papst, Denise Millier, Daniel Beckers, Axel Preusse

"At an open-pit lignite extraction mine in Germany, groundwater has to be pumped over a large area, which leads to subsidence at the surface. As long as the geology of the area of influence is homogeneous, the subsidence is uniform and has marginal influence on buildings.Since the geology of many regions is characterized by faults, there are different rates of subsidence along those faults, which can lead to considerable consequences. Those different rates of subsidence on both sides of a geological fault are associated with the structure of the geology and soil mechanical properties. Horizons with various thicknesses and types of soil are affected differently by the groundwater pumping because of the offset of the faults, and thus react dissimilarly to dewatering.The smaller the grain of the geological horizon, the stronger the chance of shrinking, which leads to a stronger effect at the surface; therefore, dewatering impacts on clayey soil are different to those on sand and gravel. Regions consisting of meadows with turf inclusions are endangered as well; compared to the surrounding geology, those areas react in an entirely different way to water removal, which leads to immense differences in subsidence.The differences in area and respective subsidence impacts, as well as if it is possible to localize those areas, is an issue which needs to be analyzed. Furthermore, detailed mapping can help in the development of future forecasts about those subsidence differences and can also help with monitoring geological faults. In the context of subsurface spatial planning, this mapping has to be kept under review medium- to long-term.INTRODUCTIONThe utilization of underground mining is of increasing significance and of high interest, both for the common good and for future generations. For decades, humanity has been extracting resources from the subsurface, and salt, coal, lignite and water - just to mention a few resources - have been extracted from underground (Sailer, 2013)."

Jan 1, 2016

By William Kendall

"A tremendous amount of research, analysis, and engineering time is used to design a proper roof support system including the type, length, and location of the roof bolts. Unfortunately, since the roof bolts are being installed under unsupported roof, the exact location for the bolt holes cannot easily be determined and then marked onto the roof. The actual location where the roof bolts are installed is typically left to visual estimates by the operator. This frequently results in either (1) the operator overestimating the space between roof bolts and installing more bolts than required, thereby increasing cost and reducing efficiency; or (2) the operator underestimating the space between roof bolts and installing fewer bolts than required, thereby reducing safety, leading to potential roof failure or possible violations.A patented laser light grid system has been developed by J .H. Fletcher and Monitech, a South African Company, to aid in proper machine positioning in the heading and proper bolt spacing. The system can also show when an entry is over width, requiring additional roof support. The system is relatively simple and inexpensive. The concept is applicable across the full range of roof bolters from low to high seams and from single boom to multiple boom bolters. The system can be configured to meet most bolting patterns.The system consists of several very small 1 milliwatt, class 2, line type lasers that project a line onto the roof. The actual laser is 27mm in diameter x 47mm long (1"" x 1.8""). In South Africa it is approved as intrinsically safe and is mounted inside a 50mm diameter x 64mm long (2""x 2.5"") protective housing. In the USA, we are seeking an X/P approval and the laser will be mounted in a headlight enclosure 110mm diameter x 125mm long (4.3"" x 5""). Fifteen of the systems have been installed in South African coal mines with good results.The system has aided the mines in meeting the bolt spacing tolerance used in the Republic of South Africa, which is typically 15% of the nominal bolt spacing or 7 in for 4-ft bolt spacing. Fletcher has submitted the system to MSHA for approval in the US."

Jan 1, 2016

By Yingzin Zhou

Partial backfilling can be used to reduce and control surface subsidence damage caused by longwall mining or pillaring operations in room-and-pillar mines. The use of partial backfill as opposed to total backfill minimizes the cost associated with such efforts. By com- paring surface subsidence, strains, and slopes, the effectiveness of partial backfilling including the amount, geometry, and location of backfill are demonstrated. Results show that it is possible to arrange a given volume of backfill in its geometry and location so that optimum effects are achieved in controlling vertical movement, surface slope, and curvature.

Jan 1, 1990

By Rudrajit Mitra, Tien Dung Le, Chengguo Zhang, Bruce Hebblewhite, Joung Oh

"Geomechanical and geotechnical characteristics of coal seam are important parameters that directly affect the cavability of top coal in the longwall top-coal caving (LTCC) method. The impact of these parameters such as coal strength, coal deformation modulus, coal discontinuities and top-coal thickness on cavability has not been fully understood in previous numerical analyses. The limitation and selection of the numerical modelling codes were two of the main reasons. In this paper, detailed caving simulations are performed using a 2D distinct element method (DEM) code, UDEC, to study the effect of various critical parameters on top-coal cavability. The numerical analysis evidently shows that the coal deformation modulus, coal discontinuities, and top-coal thickness have considerable influences on cavability. Coal strength is also a factor but to a lesser extent. The results presented in this paper contribute to the understanding of top-coal cavability in different mining environments and facilitate the development of an advanced cavability evaluation criterion. INTRODUCTION The longwall top-coal caving (LTCC) method was originally developed in the 1950s in the former Soviet Union and France (Tien, 1998). The method was nearly abandoned in Europe after the mid-1980s; however, it has been significantly improved and widely applied in China since the late 1980s. A conceptual model of the LTCC method is shown in Figure 1 in which a thick coal seam is divided into two sections including the lower or cutting section, and the upper or top coal section. The lower section of coal seam is mined by conventional longwall method. Meanwhile, the upper section is recovered by caving through the face support. The LTCC method is considered to be the most viable option for mining general thick seams. Compared to the multi-slice longwall (MSL) method, LTCC has the major advantages (Zhongming, 2001; cited by Vakili, 2009):"

Jan 1, 2017

By M. Afsari Nejad

A Transversely Elasto-Plastic Model was configured in FLAC (Fact Lagrangian Analysis of Continua) as a more realistic simulation of stratified and inclined strata behaviour examining surface subsidence above the inclined longwall panels (I ). The failure criterion employed was a modified Mohr-Coulomb failure criterion that assumed a variable cohesion, which changed with respect to the orientation of the plane of anisotropy . Using the proposed numerical modelling technique several longwall panels with different configurations were simulated. The results of both surface subsidence and horizontal displacements were validated against UK data using the Subsidence Engineer's Handbook (S.E.H) subsidence prediction method and the Influence Function Method (2). It was found from the research that the incite properties as well as laboratory to field reduction factors arc depth dependent. A set of relationships for calculation of anicotropic stiffness and strength parameters have been derived. The proposed modelling approach has been successfully applied to surface subsidence prediction for 3 collieries in the UK allowing the results of the simulation to he validated directly against measured data.

Jan 1, 1998

By A. Chrzanowski

The integrated approach to monitoring surveys is based on a simultaneous utilization of geodetic, photogrammetric and geotechnical measurements of displacements, tilts, strains and any other geometrical parameters of deformation. New techniques for the integrated surveys are being developed at the University of New Brunswick in cooperation with the Canada Centre for Mineral and Energy Technology. A telemetry system for continuous monitoring of geotechnical measurements under difficult climatic and topographic conditions has been constructed and successfully tested in a coal mining area in western Canada. A generalized method for analysing the integrated deformation measurements has been developed and applied in the test area to yield three dimensional empirical modelling of surface movements from geodetic, photogrammetric and tilt surveys. The most appropriate model can be chosen from a statistical assessment of several modelling possibilities. The empirical model of the deformation can be employed in a "calibration" of the prediction (deterministic) model of the ground movements. A computer programme for two- and three-dimensional finite element modelling of elasto-plastic deformations has been developed at UNB as a part of the integrated approach. The :EM has been tested in predicting deformation in the test area in difficult geological conditions which were associated with an extraction of a steeply inclined coal seam. The results gave good agreement with the actual displacements obtained from geodetic measurements and confirmed the existence of a suspected fault.

Jan 1, 1984

By Gamal Rashed

This research is divided into two parts: the first part of this research focuses on understanding coal mine bump mechanisms, and the second part focuses on mitigating the violent failure associated with a bump. Many researchers believe that the coal bumps happen because of sudden loss of constraint between pillar/ roof and pillar/floor or the hammering effect due to the breaking of thick, massive strata above the coal seam, creating a sudden impact load on the pillars and causing them to bump. However, very little work has been done to explore and understand the consequences of these proposed mechanisms for coal bumps. In the first part of this research, computer simulation of coal specimen behavior have been used to explore two issues: 1) How would an instantaneous loss of constraint or a small sudden impact load cause violent failure? 2) How does the strength of the coal specimen control coal mine bumps? Eliminating or reducing the violent failure is the main objective of the second part of this research. The coal specimen needs to be softened either in the rib zone or the core zone and then its mode of failure studied to see whether it is violent or not. Instantaneous loss of constraint and the hammering effect are associated with sudden release of elastic energy, increase in the kinetic energy, and very rapid transient vertical stresses of the coal specimen. These are three of the major proposed mechanisms for bumps. The potential for violent failure increases with increasing the unconfined compressive strength, UCS, of the coal specimen. Failure of the rib zone is not the main factor for the violent failure of a coal specimen. The energy stored in the core zone is the key factor for the violent failure.

Jan 1, 2013