Search Documents

By Eric C. Poeck, Ryan Garvey, Ugur Ozbay, Kun Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/ rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the minescale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures that most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps.IntroductionThe analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but, for deep cover and squat pillar (w/h > 10) geometries, pillar performance predictions are not as accurate (Mark, 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs."

Jan 1, 2015

By James D. Pile

Following a methane ignition in the active panel of a longwall coal mine, the affected panel was successfully isolated from the rest of the mine. This allowed for the remainder of the mine to return to regular operation, and the conventional practice of having to seal the portals for a defined period of time was avoided. After the affected panel had remained isolated for a regulatorily mandated period of time, it was reopened in preparation for longwall face recovery. As it was not possible to move the shields from their existing positions to facilitate the installation of recovery mesh prior to shield recovery, alternative methods had to be considered to stabilise the gob and minimise flushing, thereby improving operator safety. The objective of the paper is to show how stabilisation of the gob was achieved during shield recovery, thereby minimising flushing, and improving operator safety. Phenolic foam was chosen and injected from between the shields into the gob behind them. This is a technique that has been used to great effect in Germany, to a lesser extent in Australia, but not knowingly to date in the United States. To ensure nothing was left to chance and thereby guarantee the project?s success, the procedure used in Germany was employed, down to the application of equivalent hardware, which was sourced through the North American supplier.

Jan 1, 2013

By Michael Gauna, Christopher Mark

"Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. Despite decades of research, the sources and mechanics of these events are not well understood, and therefore they are difficult to predict and control. Experience has shown, however, that certain geologic and mining factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present, and then identifying appropriate control measures to mitigate the hazard. This paper summarizes the U.S. and international experience with coal bursts, and describes the known risk factors in detail. It includes a framework that can be used to guide the risk assessment process.BACKGROUNDCoal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. During the years 2012-2014, serious coal bursts occurred at three different U.S. room and pillar mines. These events resulted in three fatalities and two permanently disabling injuries (MSHA, 2014; MSHA, 2013). In all three instances, the events occurred during pillar recovery at depths exceeding 1,000 feet (300 m). None of these three mines had previously reported a burst to MSHA. Coal bursts also occurred at three longwall mines during this same time period.Despite decades of research, the sources and mechanics of bursts are not well understood, and therefore these events are difficult to predict and control. Experience has shown, however, that certain risk factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present. In addition, some control techniques are effective in reducing the likelihood of an event or protecting miners from their effects."

Jan 1, 2015

By Nikzad Oraee, Parham Khajehpour, Kazam Oraee, Arash Goodarzi

"Rock fall related accidents continue to occur in coal mines, although artificial support mechanisms have been used extensively [1]. Roof stability is primarily determined in many underground mines by a limited number of methods that often resort to subjective criteria. It is argued in this paper that stability conditions of mine roof strata, as a key factor in coal mines, must be determined by a survey which proactively investigates fundamental aspects.Failure of rock around the opening happens as a result of both high rock stress conditions and the presence of structural discontinuities. The properties of such discontinuities affect the engineering behavior of rock masses causing wedges or blocks to fall from the roof or slide out of the walls [2]. A practical rule based approach to assess the risk of a roof fall is proposed in the paper. The method is based on the analysis of structural data and the geometry and stability of wedges in underground coal mines. In this regard, an accident causing a huge collapse in a coal mine leading to four fatalities is illustrated by way of a case study. A comprehensive investigation of the hanging wall has been gathered through a systematic collection of evidence. The investigation results are then analyzed, and an interpretation of the evidence gathered is provided.For this purpose, horizontal and vertical profiles are prepared by geophysical methods to define the falling zone and its boundaries. The collapse is then modeled by the use of sophisticated computer programs in order to identify the causes of the accident and hence recommend corrective actions to prevent or minimize reoccurrence probability of similar accidents. The corrective measures are placed into a rule-based framework for the benefit of the mine operators.INTRODUCTIONRoof rock failure has generally been the most dangerous hazard for underground coal mining in the world. Failure of rock around shallow coal mine openings often results from loosening of blocks of rock on the weakened planes under the influence of gravity. This condition is not typically seen in large deep coal mines. There are a number of differences between large mechanized mines and small mines related to ground control [3]."

Jan 1, 2015

By Shuren Wang, Wenbing Guo, Paul C. Hagan, Yanhai Zhao

"The overlying strata is often destroyed in large scale during shallow coal seam mining, and the sliding instability of the caved roof seriously threatens the safety of the mining field. The typical shallow coal mining in Shendong Mining Area in China was used as engineering background; the load distribution characteristics of the overlying strata were analyzed based on the monitoring data of the support resistance. Through theoretical analysis and numerical simulation, the formation and changing process of the pressure-arch in the overlying strata were studied, and the instability mechanism of the overlying strata was revealed by focusing on the accumulation and release law of the elastic energy in the pressure-arch. The results show that the continuous pressure-arch was formed when the horizontal stress exceeded the primary vertical stress of the mining field, and the elastic energy of the roof was released by the mining unloading effect. The elastic energy was accumulated in the pressure-arch, and the energy arrived the highest at the front arch foot. The accumulated energy at the arch foot was released by coal mining, and the shear zone could be formed. Therefore, the sliding of the caved zone along the shear zone induced strong roof weighting. The concentrated stress and the released energy during each mining increased with the panel advancing, and the height of the shear zone also increased. The conclusions obtained in the study are of important theoretical value to direct similar engineering practice.INTRODUCTIONThe instability of overlying strata during shallow coal mining, such as the large-scale roof falling and step-like ground subsidence, is a key problem that can restrict the safety mining in the mines (Ju and Xu, 2015). The self-bearing structure of the pressure-arch can form in the overlying strata after coal mining, and this structure can support the load of the upper strata and soil layer, so the weighting intensity of the panel is determined by the caved rock in the unloading zone under the inner boundary of the pressure-arch. A large amount of elastic energy is accumulated in the pressure-arch under the concentrated stress, and the released energy for mining is the internal cause of rock failure (Wang et al., 2017). It is an important problem to reveal the distribution characteristics of the stress and energy fields in the mine and to analyze the stability of the overlying strata during shallow coal mining based on the evolution characteristics of the pressure-arch."

Jan 1, 2018

By Hongwei Wang, Hao Zhang, Panshi Xie, Xicai Gao, Youfu Zeng, Yongping Wu, Juan Dou

"The reserves and production of steep coal seams account for approximately 15–20% of the total coal reserves in China and 5–10% of the total annual coal production. More than 50% of the coal is high-quality coking coal and anthracite, based on reviews of steeply dipping seam mining at home and abroad. Fully mechanized mining is considered to be the only safe and efficient way to mine steeply dipping seams. To achieve fully mechanized longwall mining, four issues must be addressed: ground control, equipment stability control, development of complete sets of equipment, and safety. Engineers must focus on many factors of steeply dipping seams, such as the following: stope, roof asymmetrical structure, stability control, “roof-support-floor” system dynamics control, multi-region big-range ground control technology, adjustment false-inclined method, nonlinear layout method, control technology, safety, and development of complete sets of equipment. Engineering practices in China introduce these concepts systematically: fully mechanized mining of medium-thickness seams, fully mechanized high mining of thick seams, fully mechanized caving of extremely thick coal seams, fully mechanized mining of coal seams, roadway support, and so on. A steeply dipping seam is one with a dipping angle in the range of 35°–55°. This accounts for about 15%–20% of the total coal reserves in China. Because of the environment, more than 50% of the coal is high-quality coking coal and anthracite. Mining steeply dipping coal seams is known to be difficult in the mining industry. After the study conducted by Germany, Poland, and the former Soviet Union in the1970s–1980s, the fully mechanized mining basic theory, core technology, and key equipment research have not been a breakthrough. Being fully mechanized is a technological “restricted area” at home and abroad. A lot of steeply dipping seams are excavated by non-mechanized mining, leading to harsh job environments, labor-intensive work, low productivity, frequent accidents, and significant security hazards. The death rate per million tons of coal reaches above 4.0 and is far higher than slow inclined coal seam mining. Making steeply dipping seam mining safe and efficient is a global problem that urgently needs to be solved. Fully mechanized mining is the only way to overcome these problems (Wu, 2003; Wu, Yun, and Zhou, 2000). The realization of fully mechanized coal seam mining must solve four problems. (1) Examine the disaster mechanisms induced by overburden “key strata” mutation under steeply dipping seams as a basis for ground control methods and technical problems. (2) Work to solve the dynamic stability control technical problems of thousands of tons of complete sets of equipment under the steeply dipping seams. (3) Complete sets of equipment must be developed to adapt to the conditions of steeply dipping seams. (4) Overcome the steeply dipping face safety protection technical problems. In the last two decades, a number of universities, research institutes, and enterprises have realized the importance of safety and efficiency of steeply dipping seams in China. This is especially true of Professor Wu Yongping’s “hard coal layer safe and efficient mining” team at Xi’an University of Science and Technology. After several generations’ research and technical work, the team puts forward China’s longwall mechanized coal mining of steeply dipping seams strata control basic theory. This paper puts forth a series of key technologies of fully mechanized mining, develops and manufactures complete sets of equipment by independent innovation, and establishes a perfect face security system, forming a theory and technology system for fully mechanized longwall mining of steeply dipping seams."

Jan 1, 2017

By David W. Evans

"Induced hydraulic fracture of strata during roof bolt installation is a potentially prevalent, but masked phenomenon within the underground coal industry. Previously reported resin testing programs (McTyer et al., 2014) examined the relationship between resin mixing effectiveness and varying bore hole diameter. The methodology employed within this earlier test program facilitated a further critical area of research – the measurement of back pressures generated within the bore hole during standard rock bolt installation practices. Experimental data has indicated that fluid resin can be pressurised to levels where it exceeds the compressive strength of the strata, inducing hydraulic fracture within the immediate area of the bolting horizon. The routine cycle of roof bolting serves to propagate this effect, progressively fracturing and delaminating the roof during mine advancement. This masked phenomenon can lead to a perception of difficult ground conditions - mining efficiencies and costs are therefore affected, with increased needs for additional support subsequently required to restabilise the inadvertently damaged roof.Further analysis of the parameters associated with resin bolt installation has now been conducted, assisting in the development of an empirical relationship between bore hole pressure, bore hole diameter and bolt insertion times. This relationship has been analysed for 15:1 ratio resins and 2:1 ratioresins, within 28mm and 30mm boreholes. Further to this, load transfer performance has been comparatively assessed for both 28mm and 30mm boreholes, suggesting that for 2:1 resins, acceptable resin mixing and load transfer can be obtained within a 30mm bore hole. The combination of 2:1 resins, utilised within a 30mm bore hole, may well provide the optimal solution to reduce the risk of hydraulic fracture in weaker strata during resin bolt installation.INTRODUCTIONA growing number of industry papers have previously investigated areas of concern associated with the performance of cartridge style resins in roof bolting, predominantly focussing on the effects of plastic film gloving, inadequate resin mixing and the pressurisation of resin within the bore hole. These three effects have a critical influence on the load transfer of the steel bolt element, through the cured resin and into the surrounding strata.Gloving occurs due to the plastic film of the resin cartridge partially encasing or wrapping around the steel roof bolt element – a known phenomenon over many years (Pettibone, 1987). The plastic film creates regions of discontinuity between the bolt, cured resin and borehole, reducing effective load transfer into the strata. Experimentation conducted into the effects of bolt ends fully encased by plastic film (Pastars and MacGregor, 2005) revealed that load transfer can be reduced by 85 to 90% in worstcase occurrences. It is also known that the aggregate filler size used within the resin can assist in shredding and breaking up the plastic film – this effect was observed in a previous study on resin mixing effectiveness (McTyer et al., 2014)."

Jan 1, 2015

By Rob G. Jeffrey, Ken W. Mills, Jesse W. Puller

"A coal mine in New South Wales is longwall mining 300m wide panels at a depth of 160-180m directly below a 16-20 m thick conglomerate strata. As part of a strategy to use hydraulic fracturing to manage potential windblast and periodic caving hazards associated with this conglomerate strata, the in situ stresses in the conglomerate were measured using ANZI strain cells and the overcoring method of stress relief. Changes in stress associated with abutment loading and placement of hydraulic fractures were also measured using ANZI strain cells installed from the surface and from underground. This paper presents the results of in situ stress measurements and stress change monitoring undertaken as part of the hydraulic fracturing program.Overcore stress measurements have indicated the vertical stress is the lowest principal stress so that hydraulic fractures placed ahead of mining form horizontally and so provide effective pre-conditioning to promote caving of the conglomerate strata. Monitoring of the full-scale hydraulic fractures has confirmed the hydraulic fractures grow horizontally.Stress changes monitored during hydraulic fracturing formed part of a broader program to investigate fracture geometry and growth rates to confirm the characteristics of the hydraulic fractures placed. This monitoring showed that vertical stress in the conglomerate strata was being increased by up to 1 MPa in close proximity to the hydraulic fracture and had the effect of tending to promote asymmetrical growth of subsequent fractures about the injection borehole.Monitoring of stress changes in the overburden strata during longwall retreat was undertaken at two different locations at the mine. The monitoring indicated stress changes were evident 150 m ahead of the longwall face and abutment loading reached a maximum increase of about 7.5 MPa. The stresses ahead of mining change gradually with distance to the approaching longwall and in a direction consistent with the horizontal in situ stresses. There was no evidence in the stress change monitoring results to indicate significant cyclical forward abutment loading ahead of the face consistent with the observations of face conditions underground adjacent to both measurement locations. The forward abutment load determined from the stress change monitoring is consistent with the weight of overburden strata overhanging the goaf indicated by subsidence monitoring."

Jan 1, 2015

By C. P. Mangelsdorf

Between June of 1975 and November of 1978 Stateham and Radcliffe of the Denver Research Center of the Bureau of Mines in cooperation with officials of the Bear Coal Company of Somerset. Colorado Conducted extensive studies of the roof conditions in the Bear Mine. The purpose of the investigation was to determine the relationship if any between the length of time the roof was left unbolted and the subsequent stability of the roof. Using the comprehensive information available from Stateham and Radcliffe (1), (2), (3), (4) the author has proposed a design for a roof truss installation which might have been used in lieu of some of the bolting in the areas where bad roof was encountered. Historically roof truss installations like bolting patterns have been applied rather than designed. The purpose of the present paper is to demonstrate how with the information available, one might proceed through a semi-rational design. In spite of the very extensive documentation by Stateham and Radcliffe, it was still necessary to make some working assumptions. It is, therefore, not intended that the process here illustrated be used without modification in any other mine nor is there any criticism implied or otherwise, of the way in which Bear Coal Company conducted its operations. The author has never visited the mine in question. This paper is meant to be an encouragement award a more rational use of roof trusses in situations where it is economically and structurally reasonable to do so.

Jan 1, 1984

By Thomas M. Barczak

The performance characteristics of Mobile Roof Supports (MRS's) were evaluated through full-scale testing in the Strategic Structures Testing Laboratory at the National Institute for Occupational Safety and Health, Pittsburgh Research Center. Safety issues pertaining to the operation and design of these supports for pillar extraction during retreat mining are examined. A unique load frame, called the mine roof simulator, provided a realistic simulation of mining conditions by inducing vertical, horizontal, and lateral loading on the support. The purpose of these experiments was to determine the capabilities and limitations of the supports and to investigate factors that influence the measurement of loading and loading rate. An evaluation of the support design and load conditions that can cause support failure or loss of support capacity are discussed relative to the laboratory tests. In general, lateral loading perpendicular to the longitudinal axis of the canopy is most severe, although horizontal loading in the direction of the long axis of the canopy can also produce critical loading in some cases. The experiments indicate that both setting force and leg pressure measurements are influenced by the staging of the leg cylinders. The implications of these factors on load rate measurement are evaluated. A comparison of MRS capacity and stiffness characteristics is made to conventional timber supports.

Jan 1, 1997

By Zhengdong Liu, Kaizhong Zhang, Zhaonan Jiang, Yuanping Cheng, Biao Hu, Qingquan Liu, Ranpeng Wang

"Major coal mining areas in eastern China have entered into the deep mining state. Gas pre-drainage, which has been successful at shallower depths, is not suitable at greater depths because of complex conditions. Coal permeability, which is closely related to the damage behavior of coal, is the most important parameter in determining gas migration and gas drainage in a coal seam. To achieve an optimal gas drainage design in a deep mining state, the damage and permeability evolutions of coal should be further studied. The progressive failure process of coal has been analyzed by conducting a series of triaxial loading and unloading tests. The development of coal fractures has been successfully quantified, and the corresponding characteristic stress points have been obtained by using Martin’s fracture model and the stress-strain curve. Coal will produce plastic deformation, and its permeability will rapidly increase when the stress level reaches damage expansion stress. INTRODUCTION Coal mine methane (CMM) is a general term for all methane released during and after mining operations. CMM is both a potentially valuable energy and a serious hazard in active coal mines. Degassing coal seams is important for mitigating this hazard and results in the beneficial recovery of a cleanburning, low-carbon fuel resource (Karacan, Ruiz, Cotè, and Phipps, 2011). The permeability of coal is a key parameter in determining CMM production, coalbed methane (CBM) production, CO2-enhanced coalbed methane (CO2-ECBM) production, and CO2 storage in coal seam reservoirs (Connell, Lu, and Pan, 2010; Chen et al., 2011; Perera, Ranjith, and Choi, 2013). Significant research has been condcuted to the study of the evolution of coal permeability. These studies revealed that coal permeability evolution is controlled by the competing influences of effective stress and sorption-induced coal deformation. Chen et al. (2011) investigated the influence of an effective stress coefficient and sorption-induced strain on the evolution of coal permeability. Robertson and his team (Robertson, 2005; Robertson and Christiansen, 2005) measured sorption-induced matrix strain and permeability changes with regard to CO2, CH4, and N2. They found that the compressibility is not constant in a natural coal sample. Karacan (2007) conducted a series of experimental tests to study the swelling-induced volumetric strains internal to a stressed coal associated with CO2 sorption. Liu et al. (2016) investigated the effects of matrix swelling area propagation on the permeability evolution by using both natural and reconstituted samples. Many coal permeability models have been developed to describe the permeability evolution under uniaxial loading, biaxial strain, hydrostatic confining pressure, triaxial strain, and triaxial stress. Recently, some analytical permeability models have been developed to describe the anisotropic permeability behavior (Palmer, 2009; Pan and Connell, 2011; Robertson and Christiansen, 2005; Wang, Zang, Wang, and Zhou, 2014; Chen, Pan, Liu, and Connell, 2012)."

Jan 1, 2017

By Kanchan Mondal, Anthony (Sam) Spearing, Gopi Bylapudi, Joseph C. Hirschi

"The U.S. coal mining industry uses about 100 million rock anchors per year. ASTM F432 specifies the requirements for rock bolts on mines but does not address corrosion. Corrosion has been found to be an issue in Australian coal mines (Hebblewhite et al., 2003 and Villaescusa et al., 2007), where the problem has been researched and stress corrosion has been found to be a significant cause of rock falls. Corrosion is also a major concern for underground civil construction in the U.S. but has not been considered an issue or adequately researched in coal mines. Underground conditions are conducive to corrosion mainly because of water quality and humid conditions. There is a perception, however, that when bolts are fully grouted, adequate corrosion protection is offered to the steel. Research has shown that this is not necessarily the case, due to the formation of micro-cracks as the resin sets and with subsequent rock movement shearing the resin column. This paper outlines a method to determine the corrosion potential of bolts used in long-term excavations and suggests ways to mitigate such effects based on research conducted in the lab and on three mines.INTRODUCTIONResearch on rock anchor corrosion in mines has not been extensive enough in the past, and the effects of several factors in the mine atmosphere and waters are not clearly understood. One probable reason for this lack of research may be attributed to the time required for gathering meaningful data, which makes the study of corrosion quite challenging.Almost all the rock bolts used in coal mines are made from steel, hence the corrosion of iron needs to be understood. The corrosion of iron is an electrochemical phenomenon with the overall equation"

Jan 1, 2010

Virtually all mineable Appalachian coal seams exist in a multi-seam environment. This makes it inevitable that most seams will eventually experience interaction induced ground control and mining problems. Indeed, it has been estimated that every working face will experience interaction effects from previous or current workings at least once during its lifetime (1), and that these problems are considerably exaggerated when seams are in close proximity -- a distance of less than 110 feet. The continued increase in multi-seam problems has resulted in considerable research activities over many years (2,3,4,1). Theoretical analysis, numerical and physical model studies, statistical and empirical analysis of numerous interaction related field data have been applied to multi-seam mining situations and have identified many useful trends and design criteria (4,5,6,7). To fully utilize research results and transfer multi-seam mining technology to field engineers, a design model -- USEAM was constructed (8). This model, designed for close seam under-mining situations, was computerized to facilitate utilization. In the current research, a new computer program "MSEAM" was developed to produce a model for both under- and overmining close seam situations. It is hoped that both of these software packages will aid field engineers in using important interactive design criteria to gain a better understanding of interaction mechanisms. Through advance planning with these programs, detrimental interaction may be avoided and minimized, and occasionally a design can be selected which will allow interaction effects to be utilized to the benefit of mining operations.

Jan 1, 1987

By Kudret Tutuk, Serkan Saydam, Sungsoon Mo

"This paper presents an overview of the floor heave management at the Glencore Bulga Underground Operations and investigates the contributing factors to the behaviour of the floor. The mine experienced a number of major floor heave events in gateroads on development. As the longwall face approached the roadways, the magnitude of floor heave frequently increased, while new floor heave also developed. Furthermore, severe floor heave events took place along the longwall face. The most observed failure mode was buckling. While regular floor measurements were conducted to better understand the nature of the phenomenon, and various measures were considered to control the deformation of floor, the mining height was increased for the predicted floor heave domains, which facilitated effective management of the floor issues. The experience in the mine indicates that mainly high horizontal stresses with greater depths of cover and certain types of floor lithology configuration are likely to contribute to the failures of floor strata.INTRODUCTIONThe Glencore Bulga Underground is located in the Southwest of Singleton in the Hunter Valley of New South Wales, Australia. Blakefield South, part of Bulga Underground, commenced longwall mining in 2010, extracting coal from the Blakefield seam, while the overlying longwall panels were previously mined from the Whybrow seam. The coal seam ranges from 4.5 m to 8.0 m thick with the mining heights varying from 2.9 m to 3.5 m. The longwall panels are 320 m and 400 m wide and up to 3.5 km long.The mine experienced a wide range of floor issues around longwall panels LW7 and LW8, both 400 m wide. For instance, the concrete floor in the travel road failed and lifted as the longwall retreated in close proximity as can be seen in Figure 1. Figure 2 shows the beam stage loader (BSL) buried into the lifted floor, and Figure 3 shows a timber prop distorted due to the movement of the floor. In addition, severe deformation of the floor along the longwall face impeded the longwall operation, as shown in Figure 4."

Jan 1, 2018

By Filippo Vallianatos, Michael Verigakis, Vasili Saltas, Kosta Kaklis, Stelio Mavrigiannakis, Zach Agioutantis

"Development of failure in brittle materials is associated with microcracks, which release energy in the form of elastic waves called acoustic emissions. This paper presents results from acoustic emission measurements obtained during three-point bending tests on Nestos marble under laboratory conditions. Acoustic emission activity was monitored using piezoelectric acoustic emission sensors, and the potential for accurate prediction of rock damage based on acoustic emission data was investigated. Damage localization determined based on acoustic emissions evident in the critically stressed region in the form of scattered events or stresses below and close to the strength of the material.IntroductionNon-destructive testing (NDT) has gained popularity in recent years due to commonly available sensors, devices and software tools. Although the majority of such testing still occurs under laboratory conditions, the ultimate goal is a direct field application, especially in the case of underground mining. NDT, if properly applied, may be used to directly provide material property values and characteristics that can be used to determine rock mass or soil mass behavior, with a direct impact to mine design (Iannacchione et al., 2003).AE is generally defined as the high-frequency transient elastic waves originating from the sudden release of energy at localized points within a loaded material (Nomikos et al., 2010). The field of Acoustic Emissions (AE) due to compressive, tensile or other types of loads is a promising research area due to its wide application. The accurate identification of failure precursors stemming from AE is still an open research topic (Lei et al., 2004).Rock is a typically inhomogeneous and anisotropic material that contains several natural defects with various scales such as grain boundaries, microcracks, pores and joint inclusions (Jing, 2003; Read, 2004). Damage induced by microcracks is an essential mechanism in many brittle rocks subjected to stresses. An applied stress induces microcrack growth and damage is distributed uniformly throughout the sample. Finally, the microcracks coalesce and the damage is localized to a shear band, leading to strain softening and macro-scoping failure (Dragon et al, 2000)."

Jan 1, 2015

By Wei Yin, Yu Wu, Xiexing Miao

"For engineering problems of “three under” coal (coal trapped under buildings, waters-bodies and railways) exploitation, environment protection and gangue separation from raw coal underground exist in Tangshan Coal Colliery. By analyzing concrete technical problems, a technical approach of closed cycle “coal mining-gangue washing-backfilling-coal mining”, i.e. integration of coal mining, gangue separation and solid backfilling, is put forward with key technologies including gangue transportation with great depth, gangue separation from raw coal underground and integration of coal mining and backfilling. Based on the specific geological conditions of Tangshan Coal Colliery, 591m vertical feeding transportation system with great depth is designed; meanwhile, for efficient gangue transportation, ancillary wear-resisting pipe size and buffer equipment are optimized. Underground gangue separation system is created to be joined with the existing production system and backfilling system; besides, as per separation characteristics of coal and gangue, buddle jig is adopted for gangue roughing of raw coal underground. By cooperation of backfilling hydraulic support and other key equipment, the designed stope backfilling system completely realizes integration of coal mining and backfilling. Engineering practice shows that, through the research and implementation of the above key technologies, integration of coal exploitation, gangue separation and solid backfilling is successfully implemented in Tangshan Coal Colliery; moreover, it completely solves the three major engineering problems and realizes waste disposal, underground washing and separation, and ground surface subsidence control.INTRODUCTIONSo far, “three under” coal (coal trapped under buildings, watersbodies and railways) and key state-owned coal resources trapped under villages in China have reached 13.7 billion t and 5.22 billion t, respectively. With the development of coal enterprises, China currently has more than 1,600 gangue dumps (Miao et al., 2010a) with accumulated stack amount of 4.5 billion t, occupying a land area of 150,000 km2; moreover, surface subsidence caused by mining activities has damaged the environments of industry, agriculture, transportation and living, while new environmental pollution sources formed by coal related industries also result in damage to ecological environment (Huang et al., 2011a). On the one hand, due to large scale coal mining, some coal collieries suffering from resource exhaustion are faced with survival problems; on the other hand, coal mining has caused and been faced with increasingly prominent environmental problems, such as “three under” coal exploitation, waste disposal and ground surface subsidence control (Miao et al., 2010b; Zhang et al., 2009)."

Jan 1, 2015

By Takashi Sasaoka, Pinyo Meechumna, Hiroshi Takamoto, Pipat Laowattanabandit, Akihiro Hamanaka, Kikuo Matsui, Hideki Shimada

"The EGAT Mae Moh coal mine is an open-cut coal mine in Thailand that produces about 16 million tons of lignite annually to generate 2,400 mw of electricity. The surface mine pit covers is 4 by 7 km (2 by 4 mi) with mining depths ranging up to 260 m (853 ft). A large pit slope is formed with the progression of the mining operation. However, massive slides in the pit slope often occur due to weak planes, such as faults and bedding, and the weak mechanical properties of the rocks. Hence, a 200-300 m (656-984 ft) boundaries of rock block including coal seams is left in front of faults in order to prevent slides and maintain the stability of the pit slope. As a result, there are significant coal reserves beneath the abandoned area along the pit slope.The focus of this paper is on the applicability and design of the highwall mining for recovering much of the coal left along the pit slope.INTRODUCTIONThe EGAT Mae Moh Mine is located about 630 km (186 mi) north of Bangkok, Thailand (see Figure 1). It is the largest coal mine in Thailand and produces about 16 million tons of lignite annually from open-cut mining (70 % of the total coal produced in Thailand). The coal is used to generate 2,400 mw of electricity at the Mae Moh power plant, which is situated near the mining area. The mine pit covers an area of 4 by 7 km (2 by 4 mi) at varied depths up to 260 m (583 ft) as shown in Figure 2. As the mining operation progresses, the pit becomes to be deeper and deeper. In the year 2035, the bottom of the pit is expected to reach depths of 500-600 m and the open-cut mining operation will be finished. The possibility of an underground mining operation is being investigated.A large pit slope is formed with the progression of open-cut mining. However, massive slides often occur in the pit slope along weak planes including faults and bedding planes due to the weak nature of the rock. As a result, 200 to 300 m (656 to 984 ft) boundaries of rock including coal seams are left in place in front of faults to prevent slides and to maintain the stability of pit slope. Moreover, the dip of the slope is less than that of the planned design. As a result, there significant coal reserves abandoned along the pit slope."

Jan 1, 2010

By George Mishra

In mid-1979, J&L Steel Corporation experienced rapid failure of pillars after only two weeks' operation with a combination of full retreat and partial mining in the 154 Road Section of its Nemacolin Mine, Greene County. The rate of advance of the "squeeze line" was very rapid for the first 500 feet, but it slowed down considerably as it approached some large coal blocks and gas well barrier pillars. After moving all section equipment out tc a safe distance, all accessible headings and crosscuts were filled with cribs and tri-set posts to prevent further spread of the squeeze. At one time, there was great apprehension by mine management that without implementation of some immediate corrective measures the safety of #3 airshaft and the only haulage and access road to the 8 Road mining area would be in jeopardy. In September, 1979, the U.S. Bureau of Mines established convergence monitoring stations outby the squeeze area. Readings were taken at weekly intervals until January, 1980, and monthly thereafter. Mathematical calculations, plot- ting of contour maps, and graphing of total convergence at different stations were used to follow and analyze the progress of the squeeze and provide guidelines for mining plans in the adjoining areas.

Jan 1, 1981

By John L. Hill

Over 50 mines of the Appalachian and Illinois Basins are presently experiencing poor ground conditions believed to be caused by overlying stream valleys. The Bureau of Mines is conducting research into the causes of this problem with the aim of developing a predictive method for determining the safe limits of mining beneath stream valleys. In addition, the factors that control instability in these regions will be analyzed to provide design guidelines for adjusting support requirements. This paper presents the theorized causes of poor ground conditions beneath stream valleys and compares the theories with the results of a Bureau study of the Birchfield Mine No. 1 and a preliminary investigation of the Davidson Mine, both of southern West Virginia. The Birchfield Mine excavated four main entries beneath a 50-ft wide stream with only 50 ft of overburden. The valley flood plain is over 500 ft wide, flanked by valley wall slopes of 25 deg and relief of over 950 ft. In-mine monitoring of strata movement and detailed geologic mapping revealed that roof rock strength was greatest under high cover and weakest along outcrops and beneath the valley, with localized areas of decreases in rock mass quality. To improve the rock mass quality beneath the stream and reduce the threat of inundation, an extensive drilling program was undertaken to inject grout into the overburden from the surface. As a result, mining beneath the stream was practically routine from a ground control perspective, and water was not encountered until mining had advanced to a point beneath the floodplain that had not been grouted. The only ground control problems which were encountered were entirely a result of localized poor rock mass quality. In contrast to the Birchfield Mine, the Davidson Mine experienced failure of intact roof rock at a depth of 300 ft beneath a V-notch shaped valley with no change in rock mass quality. Finite element analysis was conducted to study the premining in situ stress at the two sites. The results are discussed within this paper and provide insight into the causes for the types of failure seen beneath valleys of varying shapes and depths.

Jan 1, 1988

By K. Y. Haramy

This report describes the development of an equation for predicting the crushing strength of 2-inch (5.08-cm) cubes of coal from point load tests made on irregular lumps. The equation was developed from point load and cube crushing strength tests performed on coal samples from six Western U.S. coal seams. For the six coals tested, the means of the point loads [(P)] in kg at failure were approximately proportional to the deans it the distances [(V)], in cm between the platen points for lumps in the 2 to 10-cm size ramie. This finding is at variance with results of tests on other rock types reported in the literature, which tend to show that P is proportional to D2 , as is normally assumed (in theoretical grounds. [The average crushing strength of a 2-inch (5.08 cu) cane for each type of coal was plotted against the log 10 of the slope of the P vs D plots, AP/AID . A straight line was fitted to these plots. The equation of the fitted line is cr = 1.72 x 10 4 10gK -2.10 x 10 4, where Cr is re estimated 2-inch (5. 08-cu,) cube crushing strength of the coal in psi and K is the scope of the straight line fitted to a plat of P v D for the same coal.]

Jan 1, 1982