Search Documents

By Christopher C. Woomer

Cyprus Shoshone Mine uses the longwall method to extract a deep, thick, pitching coal seam in the Hanna Basin of South Central Wyoming. The immediate, and main roof rock consists of weak, thinly-bedded, silty mudstones with weak, interbedded fine-to medium-grained sandstone. Tailgate ground control has been a critical factor impacting productivity at the mine. A gateroad condition mapping program for the 11 left longwall gateroads indicated potentially severe ground control problems for the tailgate. It was predicted that the existing, secondary support pattern of wood cribs would not provide adequate support capacity. As predicted, severe deterioration of the tailgate occurred in the form of a roof cutter, sloughing ribs, and failing wood cribs. Productivity was affected and additional support was required. Shoshone personnel evaluated several options for providing the additional support needed in the tailgate. The additional support system and placement method had to satisfy several requirements with respect to access, materials handling, placement method, set-up time and support capacity. Approximately 6,000-ft. of deteriorating tailgate had to be supported. The initial wood crib support system left a 6-ft. walkway for access and construction of the additional support. This access was further reduced as the roof loaded the wood cribs. This eliminated the possibility of mechanized material handling to the construction locations. All materials would have to be transported by hand. The additional support system had to be placed quickly to stay ahead of, and keep pace with, the required longwall advance rate. It had to incorporate the existing wood cribs and provide at least 500 tons of extra support capacity. And most critically, the system could not affect longwall ventilation. Longwall coordinators and engineers made the decision to use a low density, pumpable cement known to the industry as TeksealTM, to provide the system required. A 200 psi ultimate strength mix was decided on to provide the required load capacity. The existing cribs were formed with 1-in. by 6-in. boards and brattice cloth to provide the containment. To overcome the access limitations, three boreholes were drilled from the surface to the tailgate on 2,000-ft centers. A mobile pumping station was established on the surface and the TeksealTM was pumped 900-ft. down the boreholes through a 1.5-in. steel pipe, then as much as 1,800- ft. along the tailgate entry through 1.25-in. miner spray hose. The materials required for the TeksealTM supports could all be carried into the construction locations by hand. As a direct result of incorporating relatively new methods of pumping high yield, low density, cementitious grouts, the Shoshone Mine reduced downtime due to tailgate ground control problems by approximately 70% in comparison with previous Longwall panels. The longwall set three monthly production records while mining the 11 left longwall under the deepest cover, steepest pitch, and most extreme ground control conditions ever encountered at the mine.

Jan 1, 1995

By Yi Luo

In the study of the topographical effects on surface movement due to underground longwall mining, the factors that affect the incremental horizontal displacements are identified using 10 collected cases. Based on this study, the angle of surface natural slope is the major contributor to the incremental horizontal displacement while the total movement is also playing an important role in some cases.

Jan 1, 1996

By Yingxin Zhou

Virtually every coal seam in Appalachia will at some time be subject to multi-seam interaction (Wu et al, 1987). Many such problems result from seams which lie in close proximity or have split and lie within thirty feet vertically of one another. Existing techniques for multi- seam design have concentrated on conditions where the entire inner burden is not the failing member and are unsuitable for ultra-close multi-seam design. Structural integrity of the inner burden must be maintained if two superimposed seams are to be mined separately and under- standing possible failure mechanisms of the inner burden is an essential first step in the design process.

Jan 1, 1989

By Y. L. Sun

The feasibility of using the ultrasonic wave attenuation method for measuring in-situ stress is examined theoretically and experimentally. The theoretical analyses show that for a given rock type the relation between stress and attenuation coefficient ratio can be approximated closely by second-order polynomials. Combining the elastic and statistical theories, the magnitude and direction of the existing principal stresses can be predicted by using the relations between stress and attenuation coefficient ratio obtained in the calibration of core specimens. Several experiments are conducted in the laboratory on two types of rock. The experimental study consists of two parts: the attenuation-coefficient measurements in core specimens under uniaxial stress and the attenuation coefficient measurements in boreholes drilled through blocks of sandstone and limestone subjected to uniaxial compressional stress. Compressional waves are used exclusively in the measurements.

Jan 1, 1989

By M. J. Beus

A shaft is truly the "lifelinen of an underground mine. Damage to the shaft lining and guides as a result of ground movement can result in serious loss of production and extensive and continual repair. In some mining districts, annual shaft repair and maintenance costs resulting from high rock stresses and excessive displacement are in the millions of dollars per year. For many years, the Bureau of Mines has conducted research to characterize the rock mass and to develop structural guidelines to improve the design of accessways in deep mines. Much of this work has centered on determining the in situ conditions that affect the structural stability of shafts in the Coeur d'Alene Mining District of northern Idaho. Recent work by Beus and Board (1984) has concentrated on measuring the rock and support behavior during sinking of the Silver Shaft at the Lucky Friday Mine. These results are currently being used as a comparative data base for further basic research as well as to establish structural design criteria. The factors affecting the deign and structural stability of deep mine shafts are numerous. A design approach that use field data as input and directly compares field measurements with numerical models can validate the procedure and provide realistic design criteria. Naturally occurring "fixed? conditions such as magnitude, direction, and ratio of in situ stresses, geologic environment, and physical properties and constitutive relationships of the rock mass ere obviously basic to numerical modeling.

Jan 1, 1989

By Christopher Mark

A new method for the design of longwall pillars, called "Analysis of Longwall Pillar Stability" (ALPS), is described. The method is the final result of a research program that included two major field studies, extensive reanalysis of data from other in situ measurements, and detailed evaluations of available pillar design methods. The key problem addressed by ALPS is estimation of the abutment loads applied to longwall pillars. Based on underground stress measurements made in mines in three states, equations for predicting the magnitude, distribution, and time-of-arrival of abutment loads are proposed. Stress measurements are also used to evaluate empirical pillar strength formulas for use in longwall pillar design. ALPS has been verified by application to case histories from several mining areas, and examples taken from the Pittsburgh and the Blue Creek seams are presented. Step-by-step guidelines for using this design method are also given.

Jan 1, 1987

By G. C. Sun

Rock mechanics properties, i.e. uniaxial and triaxial compressive strength, indirect tensile strength shear strength, Young's modulus, and poisson's ratio were collected for coal and related strata from 50 coal seams in 90 mines. The methodology of data organization and retrieval is described in details. The values and .ranges of those properties are also discussed.

Jan 1, 1993

By Christopher Mark

Pillar recovery continues to be one of the more hazardous activities in underground coal mining. Safety requires that the roof above the intersection remain stable until after the pillar has been extracted. Artificial supports (timbers and Mobile Roof Supports) arc essential to roof stability, but so is the final remnant stump or pushout. Traditional mining practices usually called for the complete extraction of the final stump, but the recent trend (both in the U.S. and internationally) seems to be towards mining plans that leave a remnant stump. For this study, a sample of roof control plans from the Mine Health and Safety Administration (MSHA) Coal Districts were analyzed to determine current pillar recovery practices. Both full- and partial- extraction plans were included. Special attention was paid to whether plans require that a final stump be left, and whether requirements regarding the dimensions of the remnant stump are included. Foreign experience with final stumps is also summarized. It seems that the risk of major pillar falls can often be reduced by leaving final stumps that are large enough to protect the intersection, but small enough that they do not inhibit the caving of the gob. Because final stumps are often irregular in shape, a new approach for estimating their strength is described. Analyses were conducted to assess the effect of seam height and depth of cover on the potential variation in the size of remnant stumps.

Jan 1, 2001

By R. Kanniganti

The primary problems of pillar design in seams subject to interaction are due not only to difficulties in predicting loading, but also to the often unsymmetrical nature of the stress fields. The effects of uneven stress fields on failure patterns within a pillar were studied wing a two dimensional finite element method. Lower seams, including ultra- close mining situations were evaluated considering conventional pillars. Pillar case study data for under mining were analyzed to determine if empirical trends in stable pillar sizing could be derived. Recommendations for multi-seam pillar design are made, based on anticipated loading conditions within a pressure bulb. Applications of the research results are demonstrated using case studies

Jan 1, 1995

By Daniel W. H. Su

The importance of incorporating fundamental principles of rock material response and failure mechanics into a pillar strength design model has been demonstrated. To accurately assess pillar strength, a model should account not only for the characteristics of the coal, but also for those of the surrounding strata. The interactions between the pillar and the surrounding roof and floor dictate ultimate pillar strength. Confinement, or the lack thereof, provided by roof and floor frictional end-constraint is one of the most significant factors in the strength of very wide pillars. The best conditions for end-constraint occur with ideally strong roof and floor. In this paper, it will be shown that weak roof and floor may decrease the ultimate pillar strength by as much as 30% compared to ideal conditions. Field observations confirm this pillar strength reduction in the presence of weak roof and floor. Furthermore, rock partings within the coal have a variable effect on pillar strength, depending on the parting strength. A competent shale parting within the coal reduces the effective pillar height, thus increasing the ultimate pillar strength; a weak claystone parting slightly decreases the strength. Imposed load distribution also has a significant effect on pillar strength, such that asymmetric pillar loading, similar to that observed in pillars adjacent to high extraction mining, reduces the ultimate pillar strength below that of equivalent pillars subject to uniform load distributions.

Jan 1, 1997

By Peter Cain

Longwall extraction in the Phalen Scam in the Sydney Coalfield of Nova Scotia is carried out under flooded abandoned workings in the Harbour Seam 140 m above, and at depth of up to 700 m beneath the Atlantic Ocean. Careful planning of panel and pillar dimensions is necessary to prevent inflows from the overlying workings and to prevent the development of excessive subsidence strains at the seabed. This paper briefly summarises the research undertaken over the past five years by CBDC and CBCRL into the problems associated with mining under water, and then describes the development and application of a design/planning code of practice developed jointly by CBDC, CBCRL and mine regulatory agencies. The design method employed in the Code of Practise is based on empirical data from the coalfield and parameters developed from subsidence modelling and previous water inflow experience. It includes precautionary measures to be adopted during development and mining, and monitoring procedures to be followed. It is flexible enough to allow future developments in the understanding of inflow mechanisms to be incoporated without major modifications, and represents a major step forward in reducing the potential hazards associated with coal extraction in the coalfield.

Jan 1, 1996

By Frank E. Chase

Clay veins, also referred to as clay elastic dikes, have been responsible for numerous underground injuries and fatalities. These hazardous structures are also responsible for increased production costs during all phases of mining. For these reasons, the Bureau of Nines has investigated the physical characteristics of and roof instability problems associated with clay veins in order to make support and other mining recommendations. In addition the occurrence and origins of clay veins were examined to determine whether or not the structures could be projected into unmined portions of the coalbed. This investigation included portions of the Arkoma, Illinois, Northern Appalachian, Southern Appalachian, and Uarrior Coal Basins. Virtually a11 clay veins observed or documented occurred in the Illinois and Northern Appalachian Basins. Observed clay veins ranged in sire from 1 inch to 16 feet In cross-section and were found under shale, siltstone, sandstone, and limestone roof rock. Individual clay veins were predominantly composed of claystone; however, limestone. siltstone. and sandstone infilled clay veins do occur. Clay vein formation has been associated with the infilling of fissures which result from compressive, tensile, or shear ground failures. These gaping fissures were propagated by compactional processes and/or tectonic stresses active during and subsequent to coal iff cation. Associated fault, fracture, and slickenside planes commonly parallel clay veins and disrupt the lateral continuity of the immediate and, sometimes, main roof. When clay veins parallel or subparallel the direction of face advance the roof is segmented into cantilever beams causing unstable conditions. Therefore, the strata on either side of the clay vein must be bolted and strapped together to form a beam.

Jan 1, 1984

By Andre Vervoort

Falls of ground, such as falls of roof and sidewall collapses, are a major cause of fatalities and injuries in South African collieries. Based on information obtained from the accident reports of the various Chief Inspectors of nines, a statistical analysis was conducted covering the period 1970 to 1988. This study shows that the volume of rock in a fatal fall of ground is often quite small. In intersections, fatal falls are on average larger than in roadways and at the face. It was also found that in 36 % of all fatal falls of ground no temporary or permanent support was installed at the site of the accident.

Jan 1, 1990

By Floyd D. Varley

Outbursts, the sudden and violent out- pouring of material into mine openings, is a ground control problem increasingly encountered in the United States as deeper seams are developed. Outbursts, caused by several mechanisms, are the result of the loading of ground support systems be- yond their designed capacity to failure, manifested in a violent release of stored energy. There are several types of outbursts typical to deep underground coal mines. - Outbursts of the coal face due to the presence of pressure abutments in close proximity to the face. These outbursts are usually accompanied by liberation of large amounts of methane. - Instantaneous convergence of the ribs and floor due to overloading and failure of ribs which lengthens the beam of floor strata sometimes resulting in a chain reaction failure of the mine floor. - violent failure of the confined core of a pillar due to rapid loading beyond the yield point of the pillar.

Jan 1, 1986

By N. I. Aziz

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack orientation.

Jan 1, 1992

By Ian Misich

Surface subsidence resulting from "total extraction" of coal in the Collie Basin first occured in 1987 when Western Collieries Ltd trialed the Wongawilli mining method. Because very little quantitative subsidence data existed for the weak, Permian sediments, a research program was set up prior to the extraction of the first panel. The objective of the study was to be able to predict subsidence characteristics and effects prior to mining future total extraction panels. Attempts at predicting subsidence began using existing subsidence models from other coal mining regions, however, as more site information became available, it became clear that it was necessary to develop a separate, site specific predictive model for the Collie Coal Basin. Analysis of extensive field monitoring data for both surface and subsurface subsidence has produced a series of empirical models which can predict the shape of surface subsidence troughs and corresponding tills, and strains for rectangular panels and describe the sequences of ground movement from the mine root through to the ground surface. The fact that both subsurface and surface subsidence characteristics have tied in well, gives greater confidence for predictions made from these models

Jan 1, 1992

By Victor V. Nazimko

Multiple mining generates gob-interaction displacements. They redistribute stress m strata and obey laws of irreversibility thermodynamics. An irreversible state causes inhomogeneity of the stress distribution on the mass. A destressed zone develops along a working panel, and worked out panels are deprived of the destressing. The inhomogeneity is smoothed out during elapsed time.

Jan 1, 1996

By Anthony Iannacchione

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width-to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By Vincent A. Scovazzo

Benchmarking is a business management process that seeks improvement through the study and reapplication of practices conducted by industry leaders. This discussion presents objectives and organization of benchmarking applied to mining geomechanics. Similar procedures have been successfully applied to mining companies, laboratories, and research organizations involved in mining geomechanics throughout the world. Benchmarking is a structured process that allows an organization to learn from the "best" in the field. The objectives of benchmarking vary depending on the company's targeted areas for improvements. Typical goals include ground control cost reduction, enhanced safety, optimization of geotechnical staffing, development of state-of-the-art design procedures, or the adoption of the "best in the field" geotechnical data management. Once the objective of the study is established and the practices and procedures to be benchmarked are identified, a benchmarking team is formed from internal and outside specialists. Benchmarking in geomechanics is fundamentally different than in most other fields because of the effects of local geologic conditions and regulations, both of which must be understood by all on the benchmarking team, before a comparative analysis can be made.

Jan 1, 2000

By Andrew P. Jarosz

The present computerized mine planning systems use CAD-like and Data Base Management System (DBMS) environments for the handling of numerical, textural, and graphical data. These two environments are usually integrated, that the data provided by the DBMS are linked to any graphical element rendered by the CAD system. The subsidence monitoring, analysis and prediction process should be integrated with the mine design process. It should allow for the assessment of impacts of mining on surface, surface utilities, and structures. It should also provide for the measures to control mining, that will create only acceptable levels of negative impacts on the surface. The common data base, and graphical capabilities of the CAD interface, may be used with great advantage for both systems. The findings of the subsidence engineering modulus should be directly incorporated into the mine design system, and vice versa. In this paper the author suggests guidelines for the development of the comprehensive computer system, able not only to predict the vertical and horizontal components of the ground movement, but also assess the induced surface damages, and costs related to subsidence prevention and compensation.

Jan 1, 1995