Search Documents

By F. A. Molloy

As a result of feasibility studies made in 1975 a 3-0 seismic reflection survey was shot over part of the Veendam salt pillow during 1978-1979. The Zechstein salt pillow, located in the northeast of the Netherlands near the town of veendam, occurs at a depth of 1400 m and contains three carnallite rich horizons over an interval of 300 m below top salt. MgCl2 brines are produced from these layers as feedstock for a magnesia plant, which starts up in 1981. Prior to the acquisition of the seismic data four wells had been drilled. The thickness of the carnallitite layers encountered in these wells varied between 50 and 125 meters. In view of these variations it was necessary to obtain a reliable isopach of the different layers. The 3-0 seismic survey covered an area of ± 4x4 km with a sampling interval of 20 m in all directions. The data was recorded it an area array using a 120 channel instrument. Final presentation of the data was in the form of 3-0 migrated acoustic impedance cross sections. The quality and resolution of the seismic data allowed reliable structural and isopach mans to be made. It was shown that the carnallitite layers are continuous over the area surveyed, whilst local thickening is "fault" related. Having this information brine production locations could be choosen in the thicker parts, allowing maximisation of production potential whilst avoiding faults and fulfilling mining regulations. A subsequent benefit of this approach is the possibility of using the seismic data to predict ore grade. Using the available wells as calibration points the acoustic impedance response of the seismic at the well was matched to the ore grade found. From these points a synthetic section was made with varying ore grades. Pre¬liminary results are encouraging and the liability of this predictive tool will be evaluated in the light of future drilling.

Jan 1, 1981

By Neal P. Cochran

It is always a pleasure for me to address a group of mining engineers. I am doubly grateful when I am allotted sufficient time to describe the total Office of Coal Research program. My remarks are directed to our total program but I trust you will all understand my emphasis of the utilization aspect of our activities since that is my portion of the program. From its inception, the Office of Coal Research has sought out creative ideas for improving our national use of coal by developing new uses, improved mining procedures, lower costs, and appropriate studies with respect to the resource itself. Quite early in the game, our Economics and Marketing Division contracted for studies with respect to New England export market, Western coal, and similar items. Our Mining and Preparation Division has successfully developed a packaged coal-fired boiler and has partially developed a packaged fluid-bed type boiler as well. Our Mining and Preparation Division is working in such diverse fields as treatment of sewage with coal and the separation of coal into distinct-petrographic constituents so that all fractions of the coal can be put to the best possible use. We would like to be doing more work on improved mining methods, better preparation techniques, and any other mining improvement that will benefit the industry and our program. The synthetic fuel plants I will describe later will operate seven days per week, 24 hours per day. We would like the mine to operate on this same sort of cycle and are prepared to support research that will lead to this.

Jan 1, 1970

By Roger N. Kust

Because ammonia can form complex ions with certain of the transition metals, such as copper and nickel, it has long been of interest to extractive metallurgists interested in leaching or separating these metals. Although it is a relatively expensive reagent, ammonia is amenable to recycle because of its volatility. In development of processes utilizing ammoniacal leaching or separation schemes, information regarding solution vapor pressures, pH and solubility limitations is needed. There is voluminous literature on ammonia-water systems generated by the urea industry. However, frequently the systems of interest to metallurgists differ significantly in concentrations of ammonia used, the temperatures of interest. Furthermore, the differences arising from the presence of metal values in solution must be comprehended. There is surprisingly little information readily available regarding systems of practical interest to metallurgy. As a result, those interested in ammonia-based processes end up either doing expensive laboratory research to obtain necessary data or overdesigning the process. Another approach to obtaining desired information about ammoniacal systems is to attempt to calculate from first principles the various solution properties. This paper is being presented to illustrate what can be accomplished by estimating the state of equilibrium in an ammoniacal carbonate system from available thermodynamic information making simplifying assumptions when needed.

Jan 1, 1976

By Ted C. Mathews

Pre-concentration by sorting is as old as the mining industry. Inevitably waste rock is broken with ore. Separation may take place in the stopes by selective mucking and transport, or selective loading and transport of ore and waste by 12-cu, yd. shovels and 100-ton trucks in large open pit operations. Hand sorting of 1" to 16" pieces, formerly widely practiced at underground chutes and prior to or following first stage crushing, has greatly diminished in the United States with its high per hour labor cost, although still widely practiced in other countries and, surprisingly, in some of the most modern mills where inexpensive labor is available. The economics of pre-concentration by sorting is attractive since elimination of waste at any cost less than the total milling cost will show a profit. The size at which sorting should be under- taken is determined by the size at which liberation is secured to yield a product of ore and waste, and greatly influences cost and the point in the flowsheet where sorting can be undertaken. In some instances mining costs can be reduced where an inexpensive sorting system to eliminate waste is combined with a less selective and less costly mining method. This is particularly true in deep mines where hoisting capacity determines the rate of extraction and sorting is performed underground, with waste utilized for fill. Hand sorting, while efficient, is expensive because of low sorting rates. Peale (1) quotes man hour capacity at 1/3 ton per hour on sizes 3/4" to 3" copper ore, and up to 5 tons per hour on rich iron ore sized from 4" to 16".

Jan 1, 1974

By Clinton A. Hollingsworth

The Flotaire Flotation Cell is a simple, efficient hydraulic/pneumatic Flotation Cell that has no moving parts. It is normally used in conjunction with a surfactant (frother) in which case the combination is known as "The Flotaire System". On many ores, metallurgical efficiencies are substantially increased and operating costs reduce. For example, in floating phosphate rock, it is not unusual for BPL recovery to be increased more than 10%, the major increase being due to floating coarse phosphate, up to 14 mesh, and the difficult to float phosphate. Substantial improvements have also been made on coal, mica, vermiculite, kaolin, barite, copper, etc.

Jan 1, 1981

By Yvon H. Poirier

Carbon addition in the oxide pelletizing process is a big concern at the Sidbec-Normines pelletizing plant since 1976. Laboratory pot-grate testing carried out before the initial start-up of the Port-Cartier plant indicated that the nominal pelletizing grate capacity could be increased by fifteen percent with a suitable carbon addition. Also an improved induration cycle offered the possibility of a significant energy reduction within the process with no adverse effect on pellet quality. A one month plant scale program duplicated the lab test results and confirmed the anticipated cost saving by using these techniques. Since March '80, Sidbec-Normines use coke addition as a current operation. This paper reviews briefly earlier laboratory and in-plant test work carried out to investigate the effects of adding carbon materials to the Fire Lake hematite concentrate, and presents operation techniques and plant results of carbon addition in the Port-Cartier pellet plant.

Jan 1, 1982

By J. W. Keck

Pilot plant grinding and concentration test results indicate that conglomerate native copper ore can be ground and concentrated using conventional techniques. Single stage autogenous grinding and rod mill-ball mill grinding required the same amount of energy far the required comminution. Metallurgical results were comparable for both types of grinding investigated.

Jan 1, 1973

By Dana A. Echter

The Paso Diablo coal project is located in the Guasare Basin in the northwestern region of Venezuela near the border with Colombia. In 1987, Carbones del Guasare SA, a joint venture comprised of Carbozulia and A.A. Antilles Coal (an Arco and AgipCoal joint venture) was formed to develop the Paso Diablo coal reserves for world markets. Regional drilling has indicated a coal resource of more than 6 Gt (6.6 billion st). Further exploration has delineated the Paso Diablo deposit as an area particularly suited for cost-effective surface mining. The calculated economically minable reserves of this area (200 Mt or 220 million st) and the coal quality characteristics are based on extensive core drilling programs. Initial coal mining operations began in August of 1987 and the mine is presently producing at a rate of 1.5 Mt/a (1.65 million stpy). The coal is hauled about 85 km (53 miles) to a barge loading terminal at Santa Cruz de Mara using highway-type haul trucks. When the coal reaches the terminal, it is loaded into barges and then transloaded onto ocean-going vessels with barge mounted

Jan 1, 1990

By Andrew P. Gize

A petrographic approach to studying the organic matter in ore deposits is advantageous in that direct observation of sample heterogeneity can be made, organic constituents (macerals) can be identified, and valuable information about the geological history of the sample (such as thermal history, oxidation, and reworking) can be obtained. Thermally immature bitumens are compositionally and structurally heterogeneous, and optically isotropic. The end product of thermal alteration, graphite, is compositionally and structurally homogeneous, and optically an isotropic. One route by which thermally immature bitumens can approach the graphite structure Is by an aromatic intermediate phase, termed mesophase. The development of optical anisotropy and a thermal mesophase has been observed In several high temperature deposits. Textures in bitumens are described from the thermally-altered Mississippi Valley-Type deposit at Nanisivik (Northwest Territories), the silver-vein deposit at Kongsberg (Norway), and the gold deposit at Carlin (Nevada). Textural evidence for multiple generations of bitumens, supportive of a pulsing model for incoming brines, is shown. Petrological evidence for the introduction of bitumens as an immiscible phase or possibly as micelles is shown in the Carlin and Kongsberg deposits.

Jan 1, 2013

By J. Lovering, H. Wilhelm, P. Siewert

Introduction The Afton property is located 290 km (180 miles) by air east-northeast from Vancouver and 14 km (8.7 miles) west of Kamloops, a city of 60,000 people, in south central British Columbia, Canada. The mine is adjacent to the Trans-Canada Highway at an elevation of 670 m (2198 ft) above sea level. The ore body is a porphyry copper deposit that has undergone supergene alteration. The major economic minerals in the supergene zone are native copper and chalcocite with chalcopyrite and bornite in the hypergene areas. The grade is 1% with an overall copper distribution - 70% native, 25% chalcocite, and 5% chalcopyrite with bornite and covellite. The ore also contains important but variable amounts of gold and silver. The mill was designed to treat 6350 t/d (7000 stpd). Semiautogenous grinding was selected to minimize capital cost and because of the expected high clay content of the ore, which would have caused problems in a conventional crushing and screening plant. Test work indicated that a recovery of 87% was possible in a circuit incorporating both flotation and gravity separation. Flowsheet Run-of-mine ore is crushed in a 1.06 x 1.65-m (3.5 x 5.4-ft) Allis Chalmers gyratory crusher set at 228.6 mm (9 in.), closed side setting. The surge pocket, below the crusher, is emptied by a Hydrastroke feeder onto number one conveyor, which discharges onto a 180,000-t (198,416-st) coarse ore stockpile. Six Hydrastroke feeders on two conveyors withdraw the crushed material from the bottom of the pile. These two conveyors, in turn, discharge onto the belt feeding the semiautogenous mill. The live storage in the stockpile is approximately 22,000 t (24,250 st), sufficient for three days' mill feed. Primary grinding is accomplished in an 8.5-m (28-ft) diam by 3.7-m (12-ft) long Koppers (Hardinge Cascade) mill (Fig. 1) containing a 10% ball charge and driven by a 4000-kW dc variable speed motor. The mill dis¬charge is pumped by a 10 x 12 G.I.W. pump to a 1.22 x 4.88-m (4 x 16-ft) stationary screen sloped at 20°. Screen oversize returns to the semiautogenous mill (SAM), and the undersize flows by gravity to the ball mill discharge pump box. Secondary grinding is performed in a 5-m (16.4-ft) diam by 8.84-m (29-ft) Koppers overflow ball mill driven by a 3430-kW synchronous motor through an air clutch. The mill is in closed circuit with a Krebs Cyclopac containing 10 635-mm (25-in.) cyclones and the cyclone overflow, at 35% solids and 65% to 70% -200 mesh, is flotation feed. In order to limit the buildup of native copper, circulating in the secondary grinding circuit, a portion of the underflow from the cyclones is processed in a circuit containing screens, cyclones, and shaking tables to produce a finished metallic copper concentrate. Primary mill variable speed drive The overall waste to ore ratio at Afton was 4.5:1. The mining was to be done with only three shovels, which meant that it was highly unlikely that more than one of them would be in ore at any one time. The resulting inability to blend the mill feed made it impossible to prevent wide swings in the grade and grindability. The variable speed do drive motor installed on the semiautogenous mill was selected because of the extreme variability of the Afton ore body. This variability has persisted throughout the lifetime of the mine. There are times, however, when due to ore conditions, the mill is operated at full speed (78% of critical) for extended periods of several shifts duration. There are other times when the mill speed may be changed several times in a 12-hour shift due to changing ore conditions. When ore is processed that contains a fairly large proportion of fine native copper, the primary mill speed and, consequently, the tonnage may be reduced to improve the secondary grind and to maintain an acceptable grind and recovery. High clay ores require less mill speed and more dilute grinding densities. In the latter case, the slower primary mill speed also helps to minimize damage to the mill liners. Approximately 57% of the time the mill operates between 90% and 100% of full speed or between 71% and 78% of critical. The variable speed is also used for inching during mill relines.

Jan 1, 1987

By G. Guzman, L. Sevilla, M. Botz

"Newmont Mining Corporation operates the Yanacocha mine in Perú and the gold milling section of the property includes a Sulfidization-Acidification-Recycle-Thickening (SART) plant to remove copper from pregnant leach solution. Since its commissioning in 2008, the plant has been intermittently operated as needed to remove copper upstream of a carbon adsorption circuit. However, starting in 2015 Newmont expects the plant to operate on a more continuous basis in response to higher copper ores that will be processed in the gold mill. In anticipation of this, Newmont conducted a campaign in May 2014 with stockpiled high-copper ore to evaluate performance of the SART plant with elevated levels of copper in feed solution. Results from the campaign demonstrated the SART plant is capable of efficiently treating high-copper leach solution. During the campaign, leach solution copper levels ranged from about 100 to 700 mg/L, and copper removals ranging from about 56% to +99% were achieved. The median copper removal efficiency observed during the campaign was about 94%. The primary plant modification determined necessary following the campaign was the need to improve consistency with sulfide dosing. INTRODUCTION Copper removal from cyanide leach solution can be affected through the addition of sulfide at acidic pH to precipitate copper sulfide as a solid. There has been renewed interest in the process in the past several years due to the increasingly common issue of high copper levels in cyanide leach solutions. The term Sulfidization- Acidification-Recycle-Thickening (SART) is used as an acronym for the process according to the primary unit operations utilized. At a pH of approximately 4.0 to 5.0, the addition of soluble sulfide to a copper-bearing leach solution will result in the precipitation of copper sulfide (Cu2S) solid. The overall acidification and sulfidization reaction is (assuming the use of sulfuric acid for pH adjustment): 2Cu(CN)3-2 + 3H2SO4 + S-2 ? Cu2S(s) + 6HCN(aq) + 3SO4-2 The above reaction is written relative to the copper-cyanide complex 2Cu(CN)3-2, though analogous reactions also take place with the other common copper-cyanide complexes Cu(CN)2- and Cu(CN)4-3. Sulfide in the above reaction (S-2) is normally supplied as sodium hydrosulfide (NaHS) purchased in solid or concentrated liquid form. Two characteristics of this reaction that are beneficial to a leaching operation are: 1. Copper is removed from solution as Cu2S (synthetic chalcocite) solid, which can then be sold to a smelter for its copper value. 2. Cyanide that is complexed with copper in the leach solution is released as free cyanide, thereby regenerating cyanide that can be recycled to the leaching operation for continued use."

Jan 1, 2015

By Sandro Moro, Giuseppe Tiberti, Giovanni Plizzari, Antonio Conforti

"During TBM operations, thrust jacks apply high-concentrated forces to the last installed precast segment. These loads generate a disturbed region in the precast segment under the thrust jacks, in which significant tensile stresses (defined as splitting or bursting stresses) occur perpendicular to the load direction. In addition, due to the demand of compatibility, the combined effect of TBM high-concentrated loads determines tensile spalling stresses in the area far from the loads. Therefore, local rebars or fiber reinforcement are required in these areas. This paper focuses on the study of the effects generated by high-concentrated loads exerted by TBM hydraulic jacks, mainly in terms of both spalling and splitting phenomena. Experimental tests on small-scale specimens showed that polypropylene fiber reinforcement significantly enhances both the bearing capacity and the ductility. Moreover, polypropylene fibers resulted in very effective control of compatibility cracks.INTRODUCTIONTunnel segments are generally reinforced by conventional rebars (RC segments) in order to resist the tensile stresses both at Serviceability (SLS) and Ultimate Limit States (ULS).In the two last decades, Fiber Reinforced Concrete (FRC) has been used in many precast tunnel segments (sometimes also in combination with conventional rebars). Steel Fiber Reinforced Concrete (SFRC) is generally used for these applications even though there is a growing industry interest on macro-synthetic fibers for structural applications. Conforti et al. (2015) showed that polypropylene (PP) macro fibers can be used as shear reinforcement in both wide shallow and deep beams. Referring to precast tunnel linings, very few early experiences are reported in literature. Bonalumi et al. (2015) developed full-scale tests on tunnel elements reinforced by PP fiber reinforcement and conventional rebars (hybrid solution). The design process of segmental concrete tunnel linings generally models the standard load cases of demolding, storage, transportation, positioning and embedded ground condition. In all these stages the ring can be modelled as simple curved beam elements (having a height equal to the lining thickness and a width equal to the segment length). During these loading conditions, flexural demand is generally limited; thus, in case of conventional RC elements, a rather low ratio of longitudinal curved rebars is usually adopted (?s of about 0.2-0.3%)."

Jan 1, 2016

By Edward S. Frohling

Va a ser discutida la información que se requiere para un estudio preliminar de viabilidad y la información adicional que se requiere para el estudio final de viabilidad de un nuevo depósito de mineral. El estudio preliminar de viabilidad se realiza con muy poca información y con un mínimo coste para el propietario. Sin embargo, el diseno del informe preliminar es similar al utilizado para el informe final. En este momento, se supone que el resultado del estudio preliminar es favorable y el propietario autoriza el estudio final de viabilidad a una compañía de ingeniería. Se describirá el tipo de organización para completar el estudio final de viabilidad. El informe final incluirá toda la información y datos relativos al nuevo depósito de mineral. La información presentada debe ser entendida lo mismo por el personal financiero que por el técnico.

Jan 1, 1982

By J. V. Thompson

The Powderhorn complex as a source of perovskite (calcium titanate) containing about 1.5% rare earths has been examined in several recent feasibility studies. Much promising exploration and process research has been done in recent years. This paper is presented with cautious optimism and with the acknowledgment that there may be some technical and economic areas yet to be explored. The Powderhorn carbonatite and alkalic stock in Gunnison County, Colorado, lies about 203 airlines km southwest of Denver at an elevation of 2450 to 2750 m (see Figures land 2). All of the mineable ore bodies are owned by Buttes Resources Company of Houston, Texas.

Jan 1, 1990

By B. Pregerson, M. Gaft, J. Rabinowitz

The main phosphate minerals, apatite and francolite, are characterized by intensive selective photoluminescence, connected with impurities of Eu2+, Ce3+, V4+, Mn2+ and (UO22+ ). The non-uniform distribution of phosphate minerals in lumps makes photoluminescence sorting possible. As result, an intermediate product is recovered which is enriched by P205 and has relatively small amounts of chert, dolomite, calcite, fluorite, etc. In the case of Zin Phosphate Plant coarse rejects, for example, it is possible to separate a product enriched by francolite, practically free of chert and with a lowered calcite content. This material is suitable for flotation, with a potential 6-7 % increase yield of concentrate.

Jan 1, 1993

By Pedro Sanchez-Mejorada

Laguna del Rey is the name of a dry lake bed located in the State of Coahuila, Mexico in a semi-desertic terrain typical of the basin and range physiography. Química del Rey, S.A., a subsidiary of Industrias Peñoles, has been producing sodium sulphate since 20 years ago, from brines pumped from the sub-surface of the present playa. The spent brine is used as raw material for the production of magnesium oxide. An extensive, lenticular deposit is found just below the playa. It consists mostly of glauberite (sodium-calcium sulphate) and blöedite (sodium-magnesium sulphate). The glauberite occurs as thin crystals oriented at random and leave many void spaces among them. These intercrystalline spaces are partly filled with mud, but the whole mass of the evaporite is still very porous. A brine that contains in solution ions of sodium, magnesium, sulphate and chlorine occupies the voids of the sponge-like evaporite body.

Jan 1, 1984

By G. Davis

It is well known that anticipated mineral prices can have an overwhelming effect on a property's expected value. However, price movements throughout the life of a project also affect value. Thus, it is necessary to not only estimate the expected commodity price at the start of a project but also the manner in which that price is likely to fluctuate throughout the project's life. This paper provides a simple method of incorporating mineral price movements into mineral project valuations.

Jan 1, 1997

By C. D. Broadbent

Open pit blasting can be a low cost routine or a high cost bottleneck depending on geology, environment and the operator's ability to master site conditions. Because blasting is a repetitive operation, there should be ample opportunity to optimize the process; but ordinarily this optimization is rarely achieved and then only if conditions remain consistent and predictable. Often, however, and particularly with porphyry coppers, hidden differences in rock characteristics nullify the operator's best efforts. At a porphyry copper deposit being mined by Kennecott Copper Corporation, there are all of the following rock types: oxidized and fresh porphyry, altered and silicified limestone, explosion breccia, rhyolite, sandstone, shale and several others. The units can cover large areas or be limited to a few tens of feet in maximum dimension. They are rarely visible on the bench surface and often do not show up in the bench slope. Even though the blastability of these rocks varies substantially, a generally-uniform blasting pattern was formerly used with disappointing results. Secondary blasting was often required and high bottoms occurred frequently; overblasting wasted drilling time, and explosives caused excessive throw. Several possible methods for improving the blast design were considered and a geophysical method was chosen for testing. There had been reports in the journals that seismic methods were being used in Europe as aids for blasting design. A literature search turned up work by Haxby 1/ on use of a refraction seismograph for measuring pit bench rock strength. Using his work as a springboard, equipment was purchased and a program was planned and carried out for developing, evaluating and implementing the seismic method for routine mine use. Following are discussions of the development program and results.

Jan 1, 1974

By D. Malhotra

The effect of some of the reagents, namely hydrocarbon oil, Syntex (sulfated coconut oil surfactant), pine oil, sodium silicate, and lime, used at the Climax mill on the recovery and grade of molybdenite and gangue minerals has been investigated experimentally using factorially designed test approach in the laboratory. The results of the investigation are presented in two dimensional plots. The lower additions of lime (equivalent to a pH of 8 to 8.5) were desirable for maximizing recovery subject to constraints on grade. Higher additions of pine oil improved recovery, but only at the expense of grade. A mathematical model of the objectives of an operating plant was formulated and optimum reagent conditions obtained.

Jan 1, 1977

By William P. Walsh

In December 1983 the author undertook an investigation in east Texas which was organized to learn the feasibility of applying geophysical techniques over shallow lignite deposits. The work embraced experimental high resolution seismic reflection and offset Wenner resisitivity sounds over three 4 to 4 mile test sections. This site also was sponsored by Woodward-Clyde Consultants (WCC) and a consortium headed by North American Coal Corporation. The principal objective of this investigation was to learn whether the aforementioned geophysical techniques could be applied over shallow lignite deposits (i.e. located at approximately 100' to 300' in depth) and consequently provide structural and stratigraphic information useful for resource and reserve characterization. A secondary objective was to determine if these same techniques could disclose the nature of the overburden and the distribution of ground water therein.

Jan 1, 1985