Search Documents

By Dolf W. Fieldman

Most recently the geologic setting of the mineral deposits in the Silver Cliff district is described by William M. Sharp in ?Geologic Map of the Silver Cliff and Rosita Volcanic Centers, Custer County, Colorado?, (U. S. G. S. Map I- 1081). The discussion will relate only to the southern half of the Silver Cliff volcanic center and differences in geologic interpretation, which are largely structural, will be pointed out as they arise. Only the manganese/silver zone of the Kate Area will be discussed in detail.

Jan 1, 1980

By S. E. Phifer

The Haile Gold Mine was the largest gold producer east of the Mississippi River prior to 1942. It is currently the only producing gold mine in the Southeastern United States. Current development involves the mining and heap leaching of some 1000 TPD. Carbon is employed as a recovery medium. Due to its clayey nature and excessive fines in the oxide ore, agglomeration using Portland cement is required prior to leaching. The ore ranges in screen size from two inches to -200 mesh. The agglomerating step combined with certain other conditions has enabled Piedmont Mining Company to achieve recoveries of 90%.

Jan 1, 1987

By B. S. Graves

Deep well disposal of selected industrial wastes has been proved feasible and acceptable in the New Orleans area by several industries including Shell Oil Company's Norco Refinery and Chemical Plant where three of the six successful disposal wells in this area are operating. Well design and procedures for restoration of capacity are based, in most cases, on the principles of brine injection developed by oil producers in South Louisiana. Geological formations in the Gulf Coast area are suited to this type of injection because receiving strata are porous, isolated from sources of potable water and their water is compatible with the liquid wastes to be injected. This method of disposal is a simple, complete and economical solution to the problems presented by certain hard to treat wastes.

Jan 1, 1964

By J. L. Huiatt

Kerosine, fuel oil No. 2, vapor oil, and fuel oil No. 6 were separated into general hydrocarbon fractions by ion exchange chromatography and adsorption chromatography. The collecting properties of these fractions were evaluated by flotation of molybdenum and copper minerals from a natural chalcopyrite ore. Paraffin fractions and aromatic fractions of low polarity produced the best molybdenum recoveries. Selective flotation of molybdenite from copper sulfide minerals was not possible with any of the chromatographic fractions.

Jan 1, 1972

This paper addresses the valuation and development timing of an undeveloped mineral project. Traditional analysis has us developing the project immediately if its net present value (NPV) is positive. Option pricing theory finds that it is better to wait until the NPV of the property is significantly greater than zero before developing. Alternatively, when evaluating the development timing decision, we must calculate NPV using a higher "timing-adjusted" discount rate, and develop the property only if its NPV using this timing-adjusted discount rate is greater than zero. This paper uses option pricing ideas to convert this development timing advice into a more concrete and user-friendly decision rule: develop the project when its "development-timing NPV" is positive, this development-timing NPV being calculated using the normal discount rate.

Jan 1, 1997

By S. S. Peng

To prevent mine floor heave, the mechanisms of floor heave must be fully understood. Based on the field study, the mechanisms of two types of floor heaves are analyzed in this paper. The mechanical models for the two types of floor heaves are developed. The floor heave can be predicted by the developed mechanical models and the control measures are recommended.

Jan 1, 1995

By D. M. S. Bhatia

The intimate association of iron formation and massive sulfide deposits has been documented by many investigators (McAllister, 1960; Hutchinson, 1972). In a classic example of such an association four distinct facies (oxide, carbonate, silicate, and sulfide) were identified in an Algoma type iron formation occurring in Paleozoic rocks, but exhibiting physical features (banding) and chemical composition (SiO2 + A1203 + Fe2O3) typical of Precambrian iron formations. The geochemical variation of the iron formation was studied by analyzing 62 samples for Si, Al, Fe, P, S, and CO2. Following a model proposed by James (1954), the geochemical and mineralogical variation of the iron formation can be used as an excellent tool for the exploration of massive sulfide deposits.

Jan 1, 1981

By Yu-ren Jiang

Novel compounds of hydroxycarbamoyl carboxylic acids, including 2-hydroxycarbamoyl -3-methlcyclohexane carboxylic acid (HCMC), 2-hydroxycarbamoylmethyl decylen-4-yl carboxylic acid (HCDC) and 2-hydroxycar-bamoylmethyl tridecylen-4-yl carboxylic acid (HCTC) were synthesized. The flotation behaviors of diaspore, kaolinite and illite using these compounds as collectors were investigated. The flotation results revealed that the floatability of the minerals was, in descending order, diaspore and kaolinite, followed by illite, and the ability to collect the minerals was, in ascending order, HCMC and HCDC, followed by HCTC. At a dosage of 2×10-4 mol/L, both HCDC and HCTC show a strong ability to collect diaspore and a weak ability to float kaolinite and illite. The flotation recovery of diaspore is over 90% and that of kaolinite and illite less than 30%. Moreover, Fourier transform infrared spectroscopy (FTIR) spectrum and zeta potential, as well as the adsorption amount, indicated that the adsorption interaction between HCTC and diaspore was primarily a kind of chemisorption in the form of chelate rings, while the interaction between the collector and aluminosilicate mineral was dominated by physisorption. It was concluded that the novel hydroxycarbamoyl carboxylic acid compounds are highly selective collectors for the flotation of diaspore vs. aluminosilicate minerals.

Jan 1, 2011

By S. Behl

A major limitation in developing successful selective flocculation schemes is the difficulty encountered in adsorbing the polymeric flocculant only on the desired substrate. In this paper a correlation between selectivity of flocculant adsorption and separation efficiency is outlined and a potential technique to achieve selective adsorption of flocculants is discussed.

Jan 1, 1992

By Ulrich Maidl, Gustavo Aguiar, Argemiro Ferreira, Marco A. Peixoto Silva, Marc Comulada

"Metro Line 5 in Sao Paulo is being constructed. This lot extends for 4,940 m with twin EPB shield tunnels under a dense and busy urban area, with an excavation diameter of 6.9 m. The tunnels run predominantly in the tertiary soils of Sao Paulo where extensive experience exists from previous EPB shield tunnel projects. However, new experience is being gained in Sao Paulo in shield tunnelling through Saprolite, the weathered product of the underlying Gneiss crystalline basement, through the resulting residual soils and in rock-soil mixed face conditions. Furthermore, experiences in difficult mixed face soil conditions with overconsolidated clay at the face in combination with loose sands at the crown under the groundwater table will be presented. Additionally, the design, operational and controlling approach followed for the shield drive at particular critical cross-sections where the shields were driven close or under buildings. INTRODUCTION Within the framework of Sao Paulo´s metro network expansion, the excavation of the shield tunnels for Metro Sao Paulo Line 5 is currently taking place. The present paper deals with the description of the most relevant features from the construction of the Line 5 – Lot 3 tunnels. The paper presents how particular challenges were dealt maximising potential of EPB shield tunnelling technology. Challenges were posed not only by the difficult boundary conditions of urban shield tunnelling, such as shield drive under buildings, but also by complex geotechnical situations. PROJECT DESCRIPTION The great urban area of São Paulo is one of the biggest cities in the world, with around 20 Million people living in the city and in the suburb area. The city faces great mobility problems and in the last years the government has been investing great amounts on the megacity´s metro expansion. The Line 5 Extension plays an important role to connect the south area to the central area of the city, with a whole extension of 11 kilometres, including 11 new stations. It is estimated that this line will transport almost 900.000 passengers/day. The first stretch of the expansion, Lot 3, consists of two single tunnels, almost 5 kilometres long each, crossing 4 stations. Figure 1 shows details of the Line 5 Expansion."

Jan 1, 2016

By R. R. Klimpel

The grinding of coal-water slurries has received increasing industrial attention during the last decade. In particular, there is long-term interest in the use of pulverized coal-water slurries to replace oil in combustion equipment and the development of coal gasification/liquefaction processes which require coal-water slurries as feed. More specifically, the use of coal-water slurries in gasification requires grinding a high density slurry containing the smallest amount of water consistent with slurry pumping and spraying. As part of a fundamental engineering research support program aimed at the industrial implementation of dense coal-water slurry grinding, this author has published several papers on how specific rates of breakage vary as a function of slurry rheology, Klimpel (1982, 1982/83). These papers demonstrated that there is a consistent pattern of change in specific rates of breakage of coal in dense slurries with controlled variations in slurry rheology. By matching rheological data with laboratory grinding results, it was possible to identify directly slurry conditions that correspond to: (1) slowing down of breakage rates, (2) the occasional acceleration of breakage of some sizes, and (3) conditions where chemical additives will increase rates of breakage.

Jan 1, 1990

By R. L. Peyton

Risk analysis is used extensively in many engineering applications. Although its use in the field of dam safety has been limited in practice, it has received considerable attention in recent years in the dam safety literature. Thus far, it has been shown that risk analysis in the evaluation of existing dams has the potential for providing a more rational basis for decision- making because of its focus on the direct issues--likelihood of failure, likelihood of loss of life, and risk cost of damages. It provides for a logical balance between the risk a dam imposes and the degree to which rehabilitation is required, compared to traditional evaluations based on somewhat arbitrarily chosen design events applied to large classes of dams. Dam owners could benefit by optimizing the cost of remedial measures. Downstream landowners could benefit by minimizing the likelihood of flood damages. However, it is also clear that significant technical and policy issues remain to be resolved before risk analysis in dam safety is accepted and routinely implemented in engineering practice. An obvious and important potential application of risk analysis is its use by the state regulatory agency as an in-house evaluation tool, or even as part of regulatory policy, in the implementation of its state dam safety program. Adoption of such a policy would have an important impact on the mining industry. .Although no state dam safety programs are known by the writers to have officially incorporated risk analysis into their regulations, there appears to be considerable interest in the concept. In recent surveys 47 states agreed that the development and promotion of a risk assessment methodology for state dam safety programs should be encouraged (Tschantz, 1983; Tschantz, 1984). The issue has also received important attention within the Association of State Dam Safety Officials (1986). One state-Illinois-proposed regulations during 1986 to allow risk analysis to justify lower spillway requirements for existing dams (Illinois Department of Transportation, 1986). At the Federal level, the National Research Council has found risk analysis especially appropriate for assessing dam safety at high-hazard dams (National Research Council, 19851, the Bureau of Reclamation has published guidelines for incorporating risk analysis into their dam safety grogram (U.S. Department of the Interior, 1986), and the Federal Emergency Management Agency has recently sponsored workshops and supported research related to risk analysis in dam safety (Federal Emergency Management Agency, 1985a ; Federal Emergency Management Agency, 1985b; - - McCann, et. al., 1985a, 1985b).

Jan 1, 1986

By K. L. Hanning

Grinding and classification circuits at Climax Molybdenum Co. are described. Since the installation of a direct digital control computer in 1974, a number of control strategies were developed and evaluated. This paper deals in particular with the practical experience and results obtained in direct digital control of a wet grinding circuit consisting of a ball mill, constant speed sump pump, and hydrocyclones. For this circuit throughput is maximized, while maintaining a desired product size. Product size is inferred from measurement of operating variables.

Jan 1, 1977

By J. R. Hunter

The present is rooted in the past. This is particularly true in the case of mining operations. Coal mining in the United Kingdom is considered an old Industry comprising today 246 Coal Mines many of which have worked coal reserves in their locality for over 100 years. More than half the current producing mines lie in the Yorkshire and Midlands coalfields. They are in the oldest age group and produce 70% of the Industry's output. Some 50% of the remaining U.K. workable reserves amounting to approximately 98,000 million tons are still available to these regions. Fig. 1 Over the past two decades a gradual erosion of demand for coal in the U.K. has virtually halved the Industry's capacity. The number of Mines has reduced by 53% during the past 10 years. Productivity has increased by some 42% mainly through improvements in the central coalfields which has enabled costs to remain broadly competitive with oil.

Jan 1, 1976

By Don Rose

Steel-fiber-reinforced-shotcrete (SFRS) methods of testing and the wording of specifications vary from country to country. In the USA ASTM C1018 is widely used. The Canadians have taken a close look at C1018 and point out that exact determination of the first crack is very subjective, and they propose a method of design that eliminates this variable. The Europeans (EFNARC) have taken the principles of testing a step further than ASTM C1018, and have added a new step in measuring the effectiveness of SFRS. EFNARC uses an "energy absorption" of a plate loaded in its center, in addition to the principles of C1018. The principles of SFRS design are also used in Japan, Norway and elsewhere.

Jan 1, 1999

By Robert R. Munro

Traditional aggregate sources, that is the riverbeds, the alluvial fans, located relatively close to the developing urban centers are being foreclosed to mining. As the sand and gravel reserves are depleted, those production plants are unable to secure additional adjacent reserves and are being forced to close down. The sand and gravel industry, in many respects, is its own worst enemy. We promote development, we promote the paving of streets, the building of houses, and industrial and commercial centers, and because of economics, we tend to favor those developments located close to our operations. Thus, we encourage development by our neighbors who soon become our detractors. In general, urban development is not compatible with sand and gravel mining. The neighbors don't like the view of the pits or the quarries, they complain about the "dust", about noise, about trucking . . . in general, the neighbors are not happy being close to an aggregate source.

Jan 1, 1984

By D. R. Bomberger

An automatic microscope has been developed to .measure the size and populations of macerals and minerals in fine coal particles. Differentiations are made on the basis of reflectance. This study is concerned with the size distribution of pyrite inclusions. Most fine coal cleaning processes do not remove pyrite as completely as a straight density separation. Consideration of the pyrite size distribution is suggested as a more accurate method of predicting sulfur reduction by a cleaning process. Analyses of float-sink results and Deister Table operation in terms of pyrite particle sizes are made. Other potential applications of automatic microscopy are also discussed.

Jan 1, 1963

By Carlos Álvarez, Sergio Sánchez, Michael Mains, Giuseppe Gaspari

Extensive record of tunnels excavated with SEM (sequential excavation method) in swelling grounds exists in literature: global experiences include successful tunnelling both through clayey and rock masses with time dependant deformation. However, TBM (tunnel boring machine) use in swelling conditions with high water pressures (EPB, earth pressure balance, machines or slurry shields) is much less documented, considering the lower expected impact due to the limited stress relief and operations under saturated conditions. This paper summarizes a number of studies conducted as part of the risk assessment and detailed design of a large diameter TBM tunnel in variable and challenging geological conditions. The tunnel alignment is driven through mixed face conditions including swelling soils and clayey soft rocks, prone to intense time-dependent deformations. The paper also describes the approach adopted for the design of pre-cast segmental lining subject to both swelling actions and high seismic loads, due to the regional active tectonic faults. The design of this lining included a detailed parametric study performed to handle the existing uncertainties related with ground characterization, potential deconnement and complex geological congurations.

Jun 23, 2024

By S. Komar Kawatra, J. J. Carlson

"It is widely known that steel made from iron ore pellets high in phosphorus is brittle. Removal of phosphorus from iron ores such as hematite has proven to be difficult. The majority of research on phosphorus removal from hematite ores has been focused on flotation. The purpose of this study was to assess phosphorus distribution under current operations at an existing hematite concentrator and determine how efficient the plant is at removing phosphorus. Objectives included: (1) Perform a phosphorus balance at an operating plant to assess phosphorus distribution under current operations; (2) Determine phosphorus removal efficiency of each separating unit and (3) Perform a quantitative liberation analysis to determine max phosphorus removal by physical means. Liberation was quantitatively determined using wet high intensity magnetic separation (WHIMS) to separate iron ore from liberated apatite (and other nonmagnetic compounds).It was observed that 61.2% of the total phosphorus entering Plant F was rejected during current operations. The desliming process was the most efficient step at removing phosphorus (45.1% P removed), whereas the flotation step was much less effective (16.1% P removed). Liberation analyses indicated that the deslime thickener may have been more efficient at removing phosphorus than the flotation circuit due to the greater abundance of liberated phosphorus in the deslime thickener feed. The scavenger returns stream was identified as having a high concentration of phosphorus and a possible point of phosphorus removal. However, liberation analyses indicated that only 32.4% of the total phosphorus in the stream was liberated. Grinding the scavenger returns to 80% passing 5.2 µm increased the amount of liberated phosphorus in the stream to 70.4%."

Jan 1, 2014

By Manuel Viveros J.

This paper will deal with the type of rocks so called evaporites, which are sedimentary rocks produced by water evaporation from seas, lakes or marginal lagoons, in warm and arid climates. Salts derived from these deposits are precipitated according to their solubility; that is, the more soluble precipitates first, overlain by other sediments like silts, shales, limestones, sands, etc. The most common evaporites, according to their chemical composition, are : Chlorides Sulphates Carbonates Nitrates Borates Common salt, or halite, sulphates like anhydrite and gypsum, are the most important. Potassium chloride (silvite and carnalite) and potassium sulphate are of great commercial value.

Jan 1, 1974