Search Documents

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Jan 1, 2011

By X. Cai, L. Jiang, G. Fu

A process for recovering manganese from low-grade manganese oxide ore through a reduction acidolysis-selective leaching method is investigated. Two types of biomass, sawdust and straw, were used as reductants. Reduction acidolysis, using concentrated sulfuric acid, was used to disrupt the structure of the biomass, allowing the biomass to be hydrolyzed into monosaccharides. Analysis by X-ray diffraction revealed that Mn2O3 was reduced to MnSO4. Then, in the selective leaching process, iron was removed through the formation of goethite. The optimized experimental parameters are as follows: reductant to ore mass ratio of 0.4, sulfuric acid to ore mass ratio of 0.9, water to ore ratio of 0.5, aging time of 18 h, leaching temperature of 95 °C, leaching time of 90 min, and solution pH of 2.5 to 2.8. Under these conditions and using sawdust as the reductant, the manganese leaching efficiency and iron removal efficiency were 91.8 and 99.2 percent, respectively.

By M. SIDDARAJU, Rameshwar Sah, T. Umadevi, K. S. SRIDHARA, M. RAJU, GANESH SHETTY

With the depletion of high-grade iron ore resources, the utilization of existing low-grade iron ores, fines and tailings with effective beneficiation is inevitable to meet the iron and steel industry’s required specifications and demand. JSW Steel Limited is operating a 17-mtpa beneficiation plant at its Vijayanagar site in Bellary in Karnataka, which produces nearly 50 to 54 percent concentrate as sinter-grade fines. The sinter base mix consists of iron ore fines that are smaller than 10 mm, with 41 percent smaller than 0.150 mm; washed ore that is generally smaller than 3 mm and bigger than 0.150 mm, with 3 to 9 percent smaller than 0.150 mm; beneficiation plant concentrate, with 97 percent smaller than 0.150 mm; limestone; dolomite; coke breeze; lime; sinter return fines; direct reduced iron (DRI) fines; and micropellets produced from steel plant waste. Using more washed ore in the sinter base mix affects the sinter quality. Ball formation in the mixing and nodulizing drum is an important step in sinter making and requires sufficient quantity of smaller than 0.150 mm fines. Optimization of fines in the sinter base was carried out by replacing the smaller than 10 mm iron ore fines with washed ore. Size analysis, study of the granulation index (G index) and optimization of moisture with respect to sinter bed permeability were carried out to optimize the proportion of smaller than 0.150 mm fines in the sinter base mix as adhering material. This study explores the optimization of fines in the sinter base mix for ball formation to achieve higher sinter quality and productivity with higher sinter bed permeability.

By B. R. Utz

The goal of the DOE Coal Preparation Program is to provide industry with the scientific and engineering knowledge base to produce economically competitive and environmentally acceptable clean coal products for both existing and new markets. The DOE/PETC in-house program continues to conduct fundamental, exploratory, and applied research in the areas of physical, chemical, and microbial coal beneficiation to assist in meeting these goals and objectives. The Coal Preparation Division now has a new Coal Preparation Process Research Facility that allows continuous bench-scale testing of emerging coal cleaning technologies and ancillary coal preparation equipment at feed rates up to 1,250 kilograms (1.25 tons) per hour. Bench-scale and laboratory-scale research projects at PETC cover areas such as 1) the use of micronized-magnetite for fine-coal, 2) heavy-media cycloning, 3) fine coal reconstitution, 4) development and testing of coal preparation process flowsheet simulators, 5) dry coal beneficiation using electrostatic methods, 6) tracer methods to determine the efficiency of density-based separations, 7) selective oxidation of organic sulfur, and 8) microbial removal of pyrite and organic sulfur from coal. This paper will discuss several of these research areas.

Jan 1, 1993

By Brian Stimpson

A recent study by the National Academy of Engineering concluded that if the U.S. Coal Industry is to double production by 1985 it must open 30 new 2,000,000 tons per year surface mines in the eastern states and 100 new 5,000,000 tons per year surface mines in the western states, in addition to major growth in underground mining. Major expansions in coal mining are also planned in other countries. Engineering geology can play an important part in coal mine development, operation and abandonment (Table I), and with the increasing scale of surface coal mining and the requirements of environmental legislation, it seems certain that engineering geology and geotechnics will play a growing role in surface coal mining.

Jan 1, 1976

By P. H. Qi

Activated carbon loaded with gold from different halide solutions has been characterized by thermal analysis techniques. The mechanism of gold uptake by carbon varies from predominately adsorption for gold iodide to predominately reduction for gold chloride. TGA and DT A measurements confirm the existence of adsorbed gold-halide species within the micropore structure of carbon. These results suggest that the ration of reduced; adsorbed gold increases for gold halides in the order Au-I > Au-Br > Au-Cl. In the case of Au-I, TA results for the loaded carbon were compared with pure compounds of 12, AuI and AuI3.

Jan 1, 1996

By James D. Piper

In the summer of 1957,9 the University of California sponsored a World Conference on Prestressed Concrete in San Francisco to which were invited a number of Soviet engineers. While attending the conference, these engineers in turn asked the University to form a delegation of American engineers to visit the Soviet Union the following year for the purpose of studying Soviet advances in concrete technology. A six man delegation was formed, and the dates of the Russian tour fixed for May 10th through May 21st, 1958. Before arriving in the Soviet Union, the American Delegation attended the Third International Congress on Prestressed Concrete in Berlin. While there, we noticed that the delegation from the U. S. S. R. used displays and showed motion pictures of many construction projects which we later were shown in Moscow. Our delegation left East Berlin by Russian aircraft on May 11th, and arrived in Moscow that afternoon. We were met by our Russian engineer hosts from The Academy of Construction' and Architecture who made all subsequent arrangements for our itinerary. This Academy has no counterpart in the United States. It. does 40 per cent of all engineering-and scientific work in the building construction field and coordinates 60 per cent of that done by other Soviet agencies. Due to the prestige of the Academy in Russian affairs, our delegation was able to obtain a surprisingly broad picture of construction activities in Moscow and Leningrad in just ten days time

Jan 1, 1960

By K. A. Wheeler

To evaluate the effects on groundwater of a proposed in-pit disposal operation at an east Texas lignite mine, the local geologic, hydrogeologic, and geochemical features were thoroughly characterized. Resultant data were used in a flow and transport model (SWIFT) to simulate migration of the ash leachate. Computer simulations indicate that the leachate plume will travel 61-152 meters from the disposal area in 100 years after resaturation of the spoils. A 61-meter buffer zone of mine spoils without ash will surround the disposal area. The proposed landfill operation received regulatory approval and is currently operating as a Class 2 non-hazardous landfill.

Jan 1, 1994

By Ralph C. Flow

In Cleveland County, North Carolina, one and one-half miles south of Kings Mountain, Foote Mineral Company operates an open pit for the production of spodumene, feldspar, mica, and commercial stone. Spodumene concentrate is sent to Footers Sunbright, Virginia plant and to other customers. Exton, Pennsylvania and New Johnsonville, Tennessee plants produce lithium compounds sold to the oil industry for multipurpose lithium-base greases, to the metal industry as welding flux, to the air conditioning market, and to the glass industry. Ceramic grade spodumene, feldspar, and mica concentrates go to other processing companies from the Kings Mountain plant. Waste amphibolite is delivered to a neighboring quarry operation.

Jan 1, 1962

By P. R. Taylor

A reaction is evaluated by which heated and pressurized water is used to precipitate metal oxides from loaded Kelex 100 complexes. Pure copper oxide (CuO) and pure nickel (Nio) in powder form, and ranging in average size from 12 to 25 micrometers, were found to precipitate from copper and nickel loaded Kelex 100/kerosene complexes, by water heated and pressurized to between 374 and 400 °c and 2170 psig (148 atm) and 3500 psig (238 atm). The precipitation is suggested to result from hydrolysis of the metal, following exchange for the hydrogen in the phenolic hydroxyl of the Kelex 100 structure, enhanced by the conditions provided by heated and pressurized water. The reaction is believed to have the characteristics of homogeneous nucleation and heterogeneous growth. The effects of temperature, pressure, initial metal concentration and seed addition on the kinetics of the process were studied. In addition, characterization studies were performed on the reaction products. A detailed discussion of the experimental results is presented.

Jan 1, 1992

By R. K. Mensah-Biney, M. T. Hepworth, K. J. Reid

The loading characteristics of gold-bromide species onto activated carbon were evaluated using a batch system. The overall loading of gold onto activated carbon was rapid for the first few hours, but it continued without cessation as a result of the reduction of gold. Therefore, conventional equilibrium considerations were not applicable. Although loading continued slowly after several days, an abnormally high, loading capacity value of 10-12 meq/g carbon (650-800 kg Au/t) could be attained in 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of (AuBr4)- species to the external surface to be reduced to metallic gold by carbon. Elution of gold from loaded carbon was feasible provided the carbon had not been loaded to high capacity values. If loading is carried to high levels, complete elution becomes impractical, and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon for gold-bromo species is discussed.

Jan 1, 1994

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

7.1 INTRODUCTION Subsidence measurements include surveys of surface and sub- surface movements and measurements and monitoring of surface structural damages. In this chapter the most commonly employed methods are discussed. 7.2 MEASUREMENT OF SURFACE MOVEMENT Surface movements involve two basic components, subsidence and displacement. The other five components (i.e., slope, curvature, strain, twisting, and shearing) are derived from the two basic components. Since all measurements are geometrical, they can be measured by common surveying techniques. 7.2.1 MONUMENTS The first step is to select the types of monuments or surveying stations. Various types of monuments have been employed. The simplest one is a paint mark on the pavement or concrete slab, although this should be discouraged because it is easily affected by artificial or environmental factors. Others use steel or wooden rods, 2 to 3 in. in diameter or square by 2 to 5 ft long, driven all the way down, flush with the ground. Both types of-monuments have no provision for frozen ground heave and both are tampered with easily. A more elaborate type is shown in Fig. 7.1 (O'Rourke et al., 1982). A rebar or iron pipe, 2 in. in diameter by 6 ft long is driven down to nearly flush with ground surface. The top 4-ft section of the hole around the pipe is enlarged to 1 ft in diameter and grouted with concrete. The most sophisticated type of monument is shown in Fig. 7.2 (Conroy and Gyannaty, 1983a). It consists of two hollow steel pipes. The inner I-in. pipe, 10 ft. long is enclosed by a 2-in. pipe at the upper 5-ft. interval. The gap between pipes is filled with foam to isolate the inner pipe from external environmental effects. The bottom of the inner pipe can either remain open or be sealed with a cap, depending on whether the ground is dry or wet. 7.2.2 MONUMENT ARRANGEMENT AND SURVEY LINES The monuments are installed strategically to form survey lines. Three basic types of monument arrangements are shown in Fig. 7.3. Figs. 7.3a and 7.3b are for single and multiple panels respectively; Fig. 7.3~ is mainly for research purposes with multiple survey lines both in longitudinal and transverse directions. This is extremely useful for defining the distributions of ground deformation, as shown in Figs. 2.10 and 2.11. Basically there are two types of survey lines: the whole basin survey line which extends across the panel width or length (e.g., lines R, R, in Fig. 7.3 a&b), and the half basin survey line which covers approximately half of the panel width or length (e.g., lines R, F in Fig. 7.3 &b). Survey lines are generally straight and linear. They should be located on the major crosssections of the subsidence basin. Survey lines must extend beyond the edge of the opening for a sufficient distance so that the edges of the subsidence basin can be determined accurately. The minimum distance from the edge of the opening must be [ ] where h = mining depth, [ ] = angle of draw, and [ ] = 5 to 7 times monument spacing for whole basin surveys, or 8 to 10 times the monument spacing for half basin surveys. There must be at least two controlling monuments at each end of each survey line. Controlling monuments must be located beyond the influence of underground mining. The spacing of the monuments ranges from 15 to 200 ft. The UK National Coal Board (NCB, 1975) recommended a spacing equivalent to 0.20 of the mining depth. Peng and Geng (1982) recommended that the maximum monument spacing be dependent on mining depths as follows:

Jan 1, 1992

By R. L. Grayson

As the total cost of labor has significantly increased over the past ten years, older underground mines have found it more difficult to compete- in a limited demand coal market. Many of the older mines were developed extensively into a reserve requiring a large number of workers to maintain and rehabilitate extensive track haulages and/or belt conveyor systems. Often, a large number of fans were required to maintain minimal airflows in areas where poor conditions and huge leakages prevail. This paper focuses upon problems which beset one such coal mine and projects undertaken to restore it to potential profitability.

Jan 1, 1986

By J. Z. Keating

There are close to two million tons of Industrial Minerals processed and sold in North America wherein the processor/marketer has no affiliation with the source mine. The largest quantity, about 800,000 tons, is barium sulfate, which is sourced in lump ore form mainly from China and India. The Alumina Trihydrate Industry sources several hundred thousand tons from various alumina refineries. Substantial quantities of bauxite, zircon, magnesite, and fluorspar arrive in North American ports each month. There are also rapidly growing quantities of offshore talcs and calcium carbonate ores being processed in U.S. plants. These feedstocks are usually quite pure, have unique properties, and enjoy bulk rail or waterborne freight economies that allow successful competition with locally sourced raw materials. With increasing restrictions on mining activities, and the increasing need for sophisticated functional minerals, the importation of minerals will continue to grow.

Jan 1, 1994

By Raymond E. Connell

From a macro business process perspective, if what we do in the Mining Industry is find material, dig it out of the ground, convert it to a product and sell it, we are in what might be considered a "simple business". If it is so simple, where does information technology fit? How does it affect our industry? Is it a strategic tool for our industry? What approach should we be employing to ensure we are utilizing information technology effectively? How is information technology integrated or tied together with other areas in the organization such as process control? What kind of people and skill sets are required to support the whole area of information technology? What effect does information technology and automation have on streamlining and rethinking the way we do business in the 90's. This paper covers how these areas have been addressed within the Noranda Group of Companies. It reviews how information technology has evolved, the approach, and what effect it has had on a diversified natural resources company in the mining and metals, forest products, and oil and gas industries.

Jan 1, 1993

By F. Woller

The territory of Czechoslovakia is well endowed in deposits of a variety of industrial minerals. At present, 29 different types of industrial minerals are mined from some 600 individual deposits in Bohemia and Moravia only. About half of those production centres involves structural materials like aggregate and common brick clays and loams. A significant proportion of industrial minerals produced in Czechoslovakia are exported. Destinations of main products are shown in Figure 1. Production of industrial minerals in Czechoslovakia has a long history. Glass has been produced since the 14th century, sulphuric acid since 1578, graphite since 1750, and chinaware since 1790, to name just a few; but most of the present production comes from deposits developed during the past forty years. For a variety of reasons, only about 30 per cent of registered and explored industrial minerals deposits in the country are in production (Table 1). Two of the reasons may be the complexity of processing or conflicting interests of parties involved, but lack of market research, investment funds, or processing capacity have also had an impact on the level of utilization of the resource base.

Jan 1, 1992

By W. E. Crandall

The Star-Morning mine is a. 1000-ton-per-day lead-zinc producer located in the easterly part of the Coeur d'Alene Mining District of North Idaho. The property includes both the Star and Morning mines which are located on the westerly and easterly portions of the same complex of veins. The mine is 70% owned by the Bunker Hill Company (Gulf Resources, Inc.) of Kellogg, Idaho, 30% owned by Hecla Mining Company, and operated by Hecla Mining Company with head-quarters in Wallace, Idaho. One of the characteristics of mines in the Coeur d'Alene District is that many of the ore bodies extend to very great depths. The Star is no exception, but rather a leading example. The complex of near vertical veins and ore shoots extend some 7000 feet below the surface at present, with a maximum strike length of about 4000 feet. Ore has been mined on 20 separate veins and ore structures. More than 50 miles of headings have been driven and nearly 23 million tons of ore mined since the Morning mine started in.189S. The problems of mining at such depths are formidable temperature on the bottom level is 1100 F and high humidity problem. Pressure from the sheer weight of rock is as high foot. This paper will deal with providing a new access to the deeper levels of the mine and the installation of a hoist and related items to service these levels. By the time development had reached the 7100 level (Figure 1), it became apparent that a different 'hoisting system was going to be necessary if we were going to continue to mine at a profit. The main shaft extended to the 4000 level at which point a ?:3100"'foot winze shaft provided access to the 7100 level. The two hoists were limited to handling 3-ton payloads at 1200 to 1500 feet per minute. Some ores are still produced from above the 4000 level but as these ore reserves become depleted the hoisting of the desired tonnage (1000+/day-) from the lower levels of the mine would exceed the capacity of the existing hoisting system. A decision was made to sink a new vertical shaft at a point well in the south wall of the ore bodies where strong rocks and a minimum of faulting was expected and to purchase and install a new hoist capable of hoisting over 7000 feet. This new' shaft, designated as the No. 4 Shaft, was planned to reach 2000 feet below the 7100 level which was the deepest level at that time. The hoist would be in-stalled on the ,main 2000 Adit level which is used as an access and haulage level to the concentrator and surface plant in Burke.

Jan 1, 1971

By William H. Lehr

A 4200 ton-per- hour marine transfer terminal, where river and oceangoing vessels simultaneously exchange cargos of coal and phosphate rock, is now in operation near the mouth of the Mississippi. Its materials handling machinery includes a bucket ladder barge unloader; a rope operated clamshell bucket unloader; a coal loader; and a rail mounted bucket wheel machine. The design and operation of this equipment is described as are the docks and conveying, breasting and barge-haul systems in use at the facility. Design considerations imposed by soil and river conditions, geography, operating needs and investment requirements are discussed. The economic significance of design and shipping innovations introduced by this facility is noted.

Jan 1, 1967

By S. S. Xue

A study has been conducted to remove iron from sulfate solutions using Eichrom's Dipex® extractant, P,P?-di(2-ethylhexyl) methanediphosponic acid (H2DEH[MDP]). It is found that this extractant can effectively and selectively extract ferric ion from highly acidic solutions. Ninety-nine percent of the iron was extracted from a simulated feed solution in a single stage. The separation factor, Fe/Zn, was 10 6 Over 90% of the iron in a loaded organic can be recovered in an aqueous solution by reductive stripping. This paper presents the experimental results. A new process for iron removal using Dipex extractant is described and discussed.

Jan 1, 1999

By Terry Ramsey, N. Finkelstein

INTRODUCTION The Cyprus Pima Mine is located 20 miles southwest of Tucson, Arizona and about fifty miles north of the Mexican border. The Cyprus Pima orebody was discovered in 1950. Feasibility studies were begun in 1952 employing underground development. Economic studies showed open pit operations to be feasible and stripping of overburden was begun in late 1955. The first ore was reached in October of 1956. A 3,000 tpd (tons per day) concentrator was completed and began operation January 1, 1957. From these beginnings, Cyprus Pima Mining Company has expanded into a plant processing approximately 54,000 to 56,000 tpd. Four expansions were required to bring the plant up to its present capacity. Each expansion incorporated what had been learned in previous operation of the plant. The first expansion was completed in August of 1963 doubling design capacity to 6,000 tpd. In reality, because of softer than average ore, capacity was closer to 8,000 tpd. Expansion I1 was completed in July 1966 bringing design capacity to 18,000 tpd. Expansion I11 followed immediately. Completed in the summer of 1967, this expansion increased the design capacity to 30,000 tpd. The actual dry tonnage of this portion of the operation in 1974 averaged 38,400 tpd, again, primarily as the result of treating softer than average ore. The latest expansion (Expansion IV), completed in December 1971 and utilizing a semi-autogenous grinding circuit, is located in a separate building (Mill 11) approximately 200 yards southeast of the original mill (Mill I). Expansion IV was designed for 14,000 tpd, but after circuit modifications, averaged 16,500 tpd in 1974.

Jan 1, 1976