Search Documents

By C. F. Johnson

Nearly all of the sulphur produced in the world today is converted to sulphuric acid and 49 % is used in the manufacture of fertilizers. In the last few years we have seen the beginning of another chapter in the volatile history of sulphur as the severe shortage of 1963:-67 has been transformed into present-day surplus. Prospects for further aggravation of this situation in the years ahead seem assured. In 1970, western world production showed a rate of increase of 4 -5%, which 1S somewhat less than that of 8% for the period 1963-1967. The rate of growth of consumption dropped considerably in 1968 when the demands of the fertilizer industry fell. During the same period of time, wide-spread demands have been set in motion for a clean environment which indicates that a fundamental change in sulphur supply, demand, and even sources, is likely to result from this upheaval. The sale of sulphur by Poland to the western world has increased and for 1970 was estimated at over one million metric tons. In the next few years, increase in Canadian sulphur supply will stern from two sources;

Jan 1, 1972

By B. R. Arvidson

Sharper separation and improved control of the top size increases the fine particle product yield. As the milling circuit recycle stream is reduced, the overall capacity is increased. In some cases, a doubling of throughput is realized, although 25 to 30% increase is more typical. Alternatively, the energy demand may be reduced, although the best economic improvement results from higher capacity. A comparison with a high-pressure roller mill circuit shows that an optimized ball mill circuit retrofitted with the new air classifier has lower energy consumption. The new air classifier features low energy demand and substantially lower maintenance compared to similar equipment. Design and operation of this recently patented classifier are discussed. Several industrial installations will be described.

Jan 1, 1999

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

The paper addresses heat stress in underground coal mines, which poses significant threats to miners’ health, safety, and productivity. It involves a comprehensive ventilation survey in three deep and mechanized underground coal mines in India. Using VentSim software, 3D simulation models were developed to predict heat stress conditions and explore the application of auxiliary ventilation and spot coolers to reduce heat stress.

Oct 1, 2023

This treatise presents the application of the vertical furnace in a carbon regeneration system. Comparison is made to a rotary kiln. The construction, operation and control of the vertical furnace and system components are discussed. Advantages include high efficiency, fuel economy, minimal mechanical apparatus and maintenance, atmospheric and temperature control, ease of operation and reliability.

Jan 1, 1985

By D. J. Miller

Environmental considerations are extremely important in planning and carrying out mergers, acquisitions and real estate transfers. It is not inconceivable that potential or actual environmental liabilities could exceed the targeted company's net worth or the book value of the real estate of interest. It is therefore essential that an environmental due diligence investigation (DDI) be performed to quantify environmental liabilities before sales, mergers or acquisitions. This paper will discuss general procedures used in environmental due diligence investigations. The emphasis will be placed on mergers and acquisitions. It should be pointed out that the procedures discussed in this paper are general and must be modified to fit each particular merger or acquisition under consideration.

Jan 1, 1988

By D. C. Torre

The need for a successful, efficient and reliable continuous face- haulage .system for use with continuous mining machines has been apparent since the first continuous miners were introduced some twenty-five years ago. Some thought and effort were given to the development of continuous haulage over the last twenty years or so. Some initial success was experienced in this area by The Long Company with a system involving bridge conveyors, as far back as the late 1950's. However, extensive success with continuous face haulage for use behind modern, high product¬ion, continuous miners escaped the industry until the early 1970's. It is true that continuous face haulage was successfully introduced into low seam mining, generally in seams ranging under 1.07 m (42") in height, in the 1960's, for use with relatively low production, low seam, auger type continuous miners. However, those available systems which have achieved success in the lower seams, where relatively low capacities are adequate, are not directly applicable for use with today's medium and high seam miners with their standard production capacity of 9.1 - 10.9 mtpm (10 - 12 tpm). Since the late 1960's and early 1970's, several machinery manufacturers, and at least two major coal companies, have devoted considerable expense, time and effort to developing truly successful continuous face haulage for use in coal seams ranging upward from 1.2 m (4') in height. Continuous face haulage equipment has been developed in the last five years employing a variety of transportation media and design concepts, including some which have received wide publicity such as those employing hydraulics, and pleated belt. The truth of the matter is, however, that the only universally applicable and widely successful continuous face haulage equipment introduced to date has been that employing a combination of bridge conveyors and mobile, self-propelled, bridge carriers, connected at the inby end to the tail of the high production continuous miner, and at the outby end attached directly to the panel conveyor (Fig. 1 & Fig. 2) or, on occasion, to a short, self-contained conveyor which, in turn, empties directly onto the panel conveyor. While these bridge type continuous haulage systems are available with both belt and chain conveyor components, the most widely applied and successful system in seams above 1.07 m (42") in height is that offered by The Long-Airdox Company. The standard unit for use with 9.1 - 10.9 mtpm (10 - 12 tpm) continuous miners is normally equipped with belt. However, they have built, and successfully applied, versions of this system employing chain conveyors, (Fig. 3), mainly for operators having extremely difficult mining conditions, including excessive amounts of water

Jan 1, 1977

By Arne Paus-Jenssen

The potash industry in Saskatchewan has recently been the focus of much new legislation at the provincial level and, along with other mining industries in Canada, also subject to changes in tax legislation at the federal level. As a result, the industry presently operates under (a) provincial production controls, a prorationing scheme; (b) a new provincial reserve tax on potash only and; (c) a new federal income tax applicable to all mineral industries. The prorating scheme dates back to 1970 and emerged as public policy because of the excess supply situation faced by the international potash industry towards the end of the sixties. This caused special problems for new mines in Saskatchewan and the provincial government decided to intervene. The new tax legislation at provincial and federal levels, both introduced within the last four years, reflects a belief that insufficient revenues accrue to the public sector from natural resources. All mining industries in Canada, including the potash industry, have had their tax positions completely reversed during these four years. Traditionally the mining sector in Canada has been a recipient of substantial tax incentives and has enjoyed low tax rates. This has changed and the mining sector is now one of the most heavily taxed sectors in the economy. In addition, the mining sector has moved from a situation where its rapid development was favoured by governments to a situation where this is no longer the case.

Jan 1, 1976

By R. E. Doerr

The successful technical demonstration of coarse coal slurry transportation at Consolidation Coal Company's Loveridge Mine in West Virginia suggests that it is now appropriate to seriously consider this technology in other applications, especially the transport of ' coal in surface mining. Early examination indicates that coarse coal slurry transport may be highly competitive with existing haulage systems, depending on a number of factors. These factors are not yet completely defined, but certainly will include production rates, coal physical and chemical properties, terrain, soil conditions, climate, water availability and quality, availability of skilled labor and other economic considerations impacting the existing haulage systems.

Jan 1, 1983

By M. S. Tsai

Recovery of uranium from wet-process phosphoric acid is a newly developed source of uranium. Many processes have been developed but the OPAP (octylphenyl acid phosphate) process is still the valuable one because the OPAP reagent compound has the high extraction ,power and cheap cost. The OPAP process was already studied by murthy(1) in 1970 and its complete process flow sheet was first fulfilled by F.T. Hurst(2) in 1974. WCFC(3) (western Co-op Fertilizer Ltd.) in cooperation with ESI (Earth Science Inc.) set up the OPAP uranium recovery pilot plant in Canada in 1978. We have studied the OPAP process since 1974 and first improved the OPAP extractant by proper adjustment of the DOPAP/MOPAP mole ratio with CH3OH-H20 method, resulting in shortening the phase separation time and avoiding the precipitation occurrence in our process. Second, we utilize the reduction and oxidation occurring by DC power supply on either side of the membrane to achieve the extraction and stripping at the same time. An improved OPAP process in which high recovery yield of uranium and acid uncontaminated by iron has been developed in our laboratory.

Jan 1, 1982

By James E. Myers

This study is a survey of the current "state-of-the-art" of commercially-available sonar tools to monitor the true shape of man-made cavities within the Hutchinson Salt of south-central Kansas. The work entailed ferreting out the available information, most of which is proprietary in nature; then examining actual existing conditions and arriving at a reasonable scientific evaluation of the method. Our studies were confined to one LPG field and two brine well operations in south-central Kansas. No field testing of any devices was performed, only questioning user firms, and studying cores, logs, and sonar surveys graciously made available by the companies we have contacted. Since these data are still somewhat proprietary, the company participants have asked that their company names be omitted from this presentation.

Jan 1, 1973

By Y. Luo

Based on the concept of slope stability analysis, a formula for determining an important parameter required in the mathematical model for the prediction of mining subsidence in hilly terrain has been proposed. The slope geometry and soil physical and mechanical properties of the surface natural slope can all be considered in the formula. Incorporation of this new formula into an existing mathematical model provides an integrated approach in studying ground movement in hilly regions.

Jan 1, 1998

The recent mine disasters in Australian coal mines have initiated an introduction of Self-Contained Self-Rescuer (SCSR) as component in the development of new escape strategies for miners. These self-contained self-rescuers are closed circuit, demand sensitive breathing apparatus that make oxygen available to the wearer for a nominal period of time. Their operation is completely independent of the surrounding atmosphere. Once properly donned, the SCSR can assist a miner to escape from an area containing smoke, toxic gases or an oxygen deficient atmosphere. The duration of a typical SCSR is usually taken at the point of complete collapse of the breathing bag which is accompanied by an increase in breathing resistance and inhaled levels of carbon dioxide. Because the oxygen consumption (V02) and the heart rate are correlated, a prediction of V02 and consequently the duration of an SCSR can be made by monitoring the heart rate. Thirty-seven volunteers participated in field simulated escape trials at four underground coal mines. The results from the field trials suggested that oxygen consumption depends on the heart rate, the body weight and exercise rating of the miner. All the volunteers were asked to fill out the questionnaires to evaluate the performance of the units. The miners indicated that they could tolerate the inhaled temperature without any difficulty to breathing resistance. A complete statistical analysis of the field results is also presented.

Jan 1, 1997

By Bernard J. Steblay

Millions of mechanical anchor roof bolts are used each year for mine structural support. The benefit of this bolting depends on a number of factors including rock density, bolt length, in situ stresses, time elapsed between mining and installation, rock properties, bolt patterns, and tension (Lang, et al., 1979). Installation tension is a major determinant of support quality. Postinstallation tensions indicate both the usefulness of the individual bolts and the behavior of the reinforced rock structure. The importance of short- and long-term bolt tension measurements is well recognized, and such measurements are required by regulations (Fed. M/NM Nine Safety and Health Reg.). These regulations also take into account the difficulty of practical tension measurements. Only a statistical sample of the bolts installed is required to be measured using current torque wrench technology. Drawbacks to this practice are that the anchorage is disturbed and perhaps weakened, accuracy is limited by friction to about 30% (Lang, et al, 1979, and Barry, et al., 1956), and the procedure is relatively time intensive.

Jan 1, 1984

By Andrzej Wala, Tom Altman, Tom Hughes

The University of Kentucky Mine Ventilation Manager (UKMVM) is a system that contains Level Five knowledge bases and comprises an expert mine ventilation management system. The package uses production rule language (PRL) to interpret data monitored from sensors, e.g., for airflow, temperature, and concentration of gases, in an underground mining environment. Activated from the PRL knowledge bases are Pascal subprograms which (1) organize the monitored data to set up emergency consultations, (2) display graphic representations of a mine's ventilation network with the latest sensor readings, (3) provide interactive updating of mine ventilation parameters, e.g., resistance changes, revised flow requirements, and new regulator and fan settings. Also activated from these knowledge bases are programs which (1) monitor airflow, temperature and gas concentrations from a physical mine ventilation model and (2) adjust regulator openings and fan rpm's. Thus, as an expert system the UKMVM not only presents advisory consultations for underground environmental emergencies, but also serves as an interface between the monitoring and responsive control aspects in the continuous maintenance of normal mine ventilation.

Jan 1, 1989

By Stephen D. Schwochow

Aggregate producers nationwide well recognize the numerous problems often faced in securing local approval to open and operate new gravel pits and rock quarries. Similar problems are faced in Colorado, but this region also presents certain political, social, and geological complexities that have become particularly troublesome in the last 10 years. The gravity of the local permitting dilemma can be related directly to the worsening supply-demand imbalance for aggregates in the state's most populated area, the Front Range urban corridor, particularly the Denver metropolitan area. The drive to develop crushed-rock reserves to supplement dwindling alluvial supplies and to meet increasing regional growth demands was somewhat predictable but perhaps more a "last resort" alternative forced onto producers by a hesitant and often apathetic government.

Jan 1, 1982

By Halter L. Gould

Since the turn of the century there has been a marked increase in population, industrial and economic growth, and in energy requirements in the United States. During this time our energy needs have been met largely by natural gas and petroleum, but as our reserves of these materials are depleted, we are going to depend more and more on our large reserves of coal. The mining of coal for electrical power production has increased at a rapid rate during the past decade. Over half the coal produced in the United States in 1971 came from mines utilizing surface mining operations (Paone, et al, 1974). Surface mining is expected to increase as the rising cost of oil places more demand on coal for energy. About 57 percent of the coal reserves in the United States lie in the area west of the 100th meridian. About one-quarter of this can be mined by current surface methods. This would involve the disturbance of approximately 1.5 million acres (600,000 hectares). By the year 2000, projections indicate disturbance of about 200,000 acres, or 300 square miles, in the West. Mined areas receiving more than 250 mm of annual precipitation can usually be revegetated without irrigation if the spoils are properly shaped, the surface layer consists of suitable plant growth media, and proven techniques in rehabilitating disturbed rangeland are applied. Areas receiving less than 250 mm of annual rainfall or with high evapotranspiration rates pose a more difficult problem. Revegetation of these areas can probably be accomplished only with major inputs of water and good management (National Academy of Science, 1974).

Jan 1, 1978

By T. J. Lutz, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

"Federal regulations require the installation of refuge alternatives (RAs) in underground coal mines. Of the in-use RAs, over 95% are mobile RAs with the remainder being built-in-place (BIP) RAs. Heat/humidity buildup has been one of the major concerns with mobile RAs. For BIP RAs, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP RAs, the National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP RA with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated, or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP RA. The results show that the air supplied to a BIP RA may require heating and cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 70°F and a humidity that reached 90 %RH, providing 55°F dew point air was able to keep the internal apparent temperature below the mandated 95°F. Results for each test case are presented. INTRODUCTION The Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines since 2008 [1]. MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. In its 2006 report, the West Virginia Mine Safety Technology Task Force recommended an apparent temperature limit of 95°F for RAs [2]. In 30 CFR 7.504, MSHA specifies a maximum apparent temperature of 95°F inside an occupied RA [3]. The apparent temperature is calculated using both air temperature and relative humidity [4]. To determine if their RAs meet the apparent temperature limit, RA manufacturers have been performing 96-hour-long heat and humidity tests in laboratories. During these tests, a heat input of 117 W (400 BTU/hr) per person is used to represent the metabolic heat of a single miner [2]. The heat generated by the RA’s carbon dioxide system is also accounted for in testing. To account for this heat, 50 W (170 BTU/hr) of heat per miner is used for a lithium hydroxide scrubbing system, or 30 W (100 BTU/hr) of heat per miner is used for a soda lime scrubbing system [5]. In these tests, air velocities around the RA are minimized to represent the worst-case scenario of an interruption in mine ventilation that might occur in a mine disaster."

Jan 1, 2017

By Herschel H. Potter

While preparing this paper, I soon realized I had a problem in defining what injuries should be classified as "personal." Admittedly, in some cases, falls of persons, sprains and strains, pulling and pushing injuries, and back injuries may have been caused by the individual. But, I believe the number of injuries directly attributed to an individual's carelessness is relatively small in comparison to the total number of injuries in those categories. For discussion purposes, the injuries most often considered to be personal, that is, caused by individuals are those classified as back injuries. My paper will be devoted to back injuries because this category represents the greatest number of injuries occurring in coal mining. A man's best friends are his wife, his back, and his dog. The back, however, has a reputation of not being as faithful as his other two friends.1 "Industrial back injury is one of the major occupational health problems plaguing industry to- day. According to national surveys, back injury accounts for more lost time than any other occupational injury and costs companies thousands of dollars in compensation, medical fees and over- time pay."2 A study conducted by USA Today found that back ailments afflict an estimated 75 million Americans, have totally disabled about 2.5 million adults, lead to as many as 200,000 required surgeries each year, are a leading cause of absenteeism and disability, are the second leading cause of hospitalization, are responsible for 18 million doctor visits a year and cost about 93 million work-days annually. The cost to industry is estimated at $14 billion a year.3 During the past 30 years, a great deal of accident prevention education has been directed toward the reduction of back injuries. However, this effort has not produced any great change in the incidence of the injury. Back injuries should be of the utmost concern to everyone here today. I don't need to tell you what the incidence rate is for back injuries, nor will I use any statistics to inform you of the incidence rate for the coal mine industry or any specific mine. It is only important to know that the number of back injuries is excessive. Back in- juries resulting from lifting have been and continue to be one of the most constant and undiminishing problems in the occupational environment. The fact is, we use our backs to per- form work that the back was not designed to do. Historically, manual materials handling related accidents have consistently accounted for the largest percentage of all industrial accidents. In fact, over 25 percent of all industrial accidents are related to handling of materials.4 In underground coal mining operations, material handling accidents account for even larger percentage of lost time injuries. In 1983, for example, they accounted for 34 percent of all lost time injuries and 32.6 percent of all non-lost time injuries. 5 I want to use one example of a task that will illustrate what I have just said: the building of a concrete block stopping. Each solid concrete block will weigh from 60 to 70 pounds. To build a stop- ping 6 feet high and 20 feet wide will take approximately 80 blocks. On the average, these 80 blocks will be handled at least four times from loading into the conveyance for transportation to being placed while constructing the stopping. This generally requires repetitive lifting from ground level. The next three slides demonstrate the lifts

Jan 1, 1986

By D. E. Hinkle

Past surface-mining operations in Appalachia primarily followed mountain con-tours. It is estimated that about 18,000 mi. of highwalls are exposed throughout Appalachia. An evaluation procedure for determining the secondary mining potential (SMP) of these highwalls has been proposed. Sixteen parameters affecting the SMP were isolated. These are grouped in four major categories: geologic conditions, existing infrastructure, site conditions, and environmental conditions. The parameters were then ranked by their impact on SMP and assigned weighting factors. A simple mathematical procedure yields an SMP number (0 < SMP < 100), which may then be used to compare alternative sites and technologies. Determination of limits and ranges while grouping data was aided by field visits to over 40 exposed highwalls in Eastern Kentucky. An interactive program has been developed to rapidly evaluate the SMP for pre-mined sites. The mathematical procedure estimates the relative potential (i.e., techno-logical feasibility) for remining for three predominant secondary mining methods: augering, Hi-wall mining, and underground mining. Other secondary mining methods are briefly reviewed and compared.

Jan 1, 1989

By Langtry E. Lynd

The titanium dioxide pigment industry in the United States has always relied to varying degrees on imported titanium concentrates. Dependence on foreign ilmenite was especially high (generally over 85% of consumption) until 1942, when large-scale U.S. production of ilmenite began, and has since ranged from 12% to 47%. Rutile import reliance was generally in the 45% to 80% range until the early 1960&apos;s, when increased use in the chloride pigment process raised dependence on imported rutile to over 90% in most years since 1963. Import reliance of zircon, obtained almost entirely as a byproduct of titanium mineral production, has generally ranged from about 30% to 65% of consumption. This paper will examine the history of U.S. sources of these heavy mineral commodities, and will discuss the potential U.S. future supply in view of changing industrial uses and processes and the anticipated development of new heavy-mineral-sand processing operations, such as those at Richards Bay in the Republic of South Africa and in Sierra Leone.

Jan 1, 1978