Search Documents

By K. Louk, E. Gilliland, N. Ripepi, M. Karmis

"Carbon dioxide (CO2) injection in deep unmineable coal seams can enhance coalbed methane (CBM) recovery as well as effectively and permanently store the CO2. Enhanced coalbed methane (ECBM) recovery and CO2 storage capacity can be improved by altering injection parameters including the injection well locations, number of injection wells, and the time and rate of the injection. A sensitivity study was performed with sixteen different injection scenarios on a coalbed methane field in Buchanan County, Virginia to understand the influence of the injection parameters on methane production, CO2 storage and the extent of the CO2 plume. History matching was done for the gas and water production period prior to injection based on field data from an active US Department of Energy funded pilot project. INTRODUCTION The coal structure is a combination of the coal matrix and cleats. In a CBM reservoir, the methane (CH4) is stored in the matrix under adsorption properties, not as a free gas. During CH4 production, the reservoir pressure is reduced and gas is released from the surface of the coal, diffuses through the matrix and transmits to fractures (man-made or natural) via the cleat network. Fractures and cleats are the major parameters that influence gas flow capacity because deliverability of the CH4 to the production well is controlled by the cleat permeability. As gas production continues over time, CH4 desorbs from coal, and coal matrix volume starts to decrease. This volume decrease in the matrix opens up the cleats, matrix shrinkage, which leads to a permeability increase. Several emprical (Harpalani and Schraufnagel 1990a, 1990b; Harpalani and Chen 1995, 1997; Harpalani and Mitra 2010; Pan et al. 2010; Liu et al. 2012; Mitra et al. 2012) and analytical (Palmer 2009; Liu and Harpalani 2013) studies have reported this relationship between pressure and permeability. Those studies showed that permeability is an important parameter in CH4 production performance. Furthermore, during gas production, water is produced through the cleat system as well, therefore gas-water relative permeability must be also considered in evaluating production performance (Gash et al., 1991). In the CO2 injection scenario the opposite occurs because CO2 has a higher adsorption affinity than CH4. CO2 replaces CH4 in the matrix of the coal and increases the volume of the coal matrix, matrix swelling, and results in a permeability decrease. Harpalani and Mitra (2010) concluded in their experimental study that swelling of the coal matrix due to the CO2 injection is two to three times more than the sorption of CH4, resulting in large permeability changes during CO2 injection."

Jan 1, 2016

By William M. Gray

[The products of mites hive historically beet a very large and important segment of total shipment transported by American Railroads. Much as the Mining transportation Executives right have wished for coal and other mineral deposits to be found along navigable rivers, where railroads have for years been competing with the very aggressive Army Corps of Engineers and the inland waterway operators, the mineable reserves are more often that not located in the arid west far from these "free" waterways. The rivers cannot go to the mines but the railroads could, did, and continue to invest it new lines to reach new mines. The mining industry and the railroad industry have good reason to rely upon each other. The former Northern Pacific Railway, the Great Northern Railway, the Chicago, Burlington and Quincy Railroad and the Spokane, Portland and Seattle Railway merged in 1970 to form the Burlington Northern Railroad, with Lou Menk as its first President. As unofficial spokesman for the industry, be had, for years, conducted a tireless effort to educate shippers, lawmakers and the general public of the single most critical problem confronting the railroad industry, the strangle bold of government regulator.]

Jan 1, 1985

By D. Bristow, D. Baker, K. Awuah-Offei, A. ur Rehman

While a body of work exists on intelligent systems for guiding occupants out of buildings during an emergency, the problem of guiding miners out of a mine during an underground emergency has not been explored. Underground evacuation fundamentally differs from building evacuation because of differences in the regulatory regime and uncertainty regarding the number of occupants. The potential for implementing an intelligent miner guidance system is buttressed by the fact that miner tracking systems, along with communication and sensor networks, already exist in underground mines. This work presents a method based on a local positioning system, in the form of a network of “nodes” at major “intersections,” which can then be used to guide miners to safety. We have developed a path-planning algorithm, based on Dijkstra’s algorithm and the local positioning system that can provide miners with the optimal escape path in an emergency. The algorithm is validated with scenarios at the Missouri University of Science & Technology Experimental Mine demonstrating the potential to include smart technology in mine emergency management and response planning. INTRODUCTION Underground mines are hazardous environments with a higher than usual risk of safety emergencies where miners have to evacuate the mine to save their lives. Mines have always trained miners to evacuate or shelter-in-place in minimum time. Jalali and Norrozi (2009) opined that the three major components that help miners in case of emergency are pre-planned optimal escape routes, decreasing delays, and improving the education of miners. In fact, Goodman and Kissel (1990) suggested that fatalities arising from mine accidents could be reduced by 50% just by decreasing delays in finding the pathways in case of emergency. The proposed work can assist miners in finding escapeways quickly in case of emergency. It is very important to have a pre-planned evacuation strategy that is clearly communicated to miners to ensure the safety of all (Conti, Chasko & Wiehagen, 2005).

Jan 1, 2019

By M. Z. Rashad

The purpose of this paper was to compare the covariance and multiquadric functions in same mining and geological applications. The basic principals of the two techniques are covered briefly. Similarities and dissimilarities of the covariance and multiquadric functions are discussed geometrically, mathematically and practically. A 14 by 16 kilometer square area in Baharia Oasis, Western Desert of Egypt, was selected for a detailed comparative test. The gravity anomalies of forty-eight test stations were computed by using the data of sixty-three control stations. The results indicated that the covariance function is quite better than the multiquadric one. On the other hand, the multiquadric function more simple in computation than the other one, which needs to precalculations such as semivariogram and covariogram. Moreover, multiquadric equations are based on geometrical and physical considerations rather than covariance functions.

Jan 1, 1990

By G. H. Harris

The flotation behavior of two high sulfur coals using a non-ionic surfactant as collector from two series of compounds containing oxygenated functional groups was studied in detail using a 2-liter Denver flotation cell. The performance of these reagents was compared with that of an oily collector, namely dodecane. The results showed that at the same coal recovery, a much lower dosage of these non-ionic surfactants was required as compared with that of dodecane. More import was the performance of these compounds as promoters for oxidized as well as un oxidized coal. Mechanisms of interaction of these compounds with the coal are suggested.

Jan 1, 1993

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By M. Rieber

The potential for the wide-spread commercialization of superconductivity, the disappearance of all resistance to a direct current (D.C.) electric flow, began in 1986-87 with the development by Bednorz and Muller at IBM's Zurich Laboratory of an yttrium -barium -copper oxide conductor which attained zero resistance at 90t:. Although the status of superconductivity is still pre-bench scale, it is useful to forecast its probable effects on the copper industry. I t should not be forgotten that at their inception, the impacts of transistors, semi-conductors, thin films and fiber optics on the electric/electronics sector of this industry, were largely underestimated. Superconductors are not metals, but a class of ceramics. They represent an efficiency increase of one or more orders of magnitude. If their development is to be a boon to the copper industry, rather than a reduction of metal demand through miniaturization or material substitution, vastly expanded copper containing electrical uses must be in prospect. In this paper the projected uses of high temperature superconductivity are examined, followed by the remaining problems to be overcome. Assuming success, a time horizon for maturation is estimated. The penalties for the non-recognition of new markets and material substitution are shown on the basis of past forecasts. Finally, the application of successful superconductivity to the copper industry over the forecast period is estimated.

Jan 1, 1990

By O. D. Staman

The risk assessment project examines the likelihood of inorganic contaminants from copper dump-leaching operations to contaminate domestic water supplies. The project examines contaminant transport by modeling contaminant movement from the base of a leach pile through the unsaturated zone and into the saturated zone. The modeling effort is unique in that it models infiltration, contaminant transport in the unsaturated and saturated zone combined with geochemical modeling of the unsaturated zone. The project incorporates probability theory to reflect the uncertainty of hydrogeologic parameters.

Jan 1, 1994

By Z. Scopa, E. Tarshizi, R. Setterlind, L. Frost, R. Livernois

"THE MINES OF THE FUTURE The mines of the future present a host of challenges, which may appear exciting or daunting depending on one’s perspective. Whether some sectors of the public recognize it or not, the demand for raw resources is not going away any time soon. In fact, it is rising as global population grows, urbanizes and attempts to steadily increase quality of life. Yes, at the same time that much of the highly developed world is calling for greener goods, reduced consumption, and cleaner production, in other areas there are cries for clean water and sanitation, consistent energy supply, access to health care and education, personal security, and support for basic human rights. The balancing act for sustainable development of our global society is indeed precarious, and the mining community is necessarily a key player. Fortunately, many industry members have accepted this role and the responsibility to provide leadership and a solid foundation for progress. Looking ahead, we need new generations of leaders, many of whom will be mine engineers, which are ready to tackle all sorts of complex problems. There are tremendous needs just for technological innovations. Increasingly tough deposits will require that we continue to expand scale toward “super” pits and “deep” underground mining fully develop unconventional recovery techniques like in-situ leaching and gasification or deep-sea extraction, and seriously consider off-earth endeavors. Such work will take entirely autonomous equipment; novel separations, processing and recycling methods; and systems that can withstand extreme physical conditions – just to name a few. It will also take a level of systems integration never-before seen in our field, complete with big data issues, sophisticated analytics and modeling efforts, and cyber-security challenges. Moreover, increasingly complex environmental problems will require creative solutions. Addressing issues like pollution control across multiple media, emerging contaminants, optimal management of wastes, selective mining, and shared use of resources between mine operations and surrounding communities and ecosystems are among top priorities. Really, a complete paradigm shift must occur, such that our focus is on overall improvement of environmental conditions, rather than minimization of impacts. A similar shift will be required in the social realm. How can we make miners safer and healthier on-site and off? How can we contribute to communities such that they are better off, now and long-term, for having a mine next door? How can we help transform artisanal mining practices to also contribute to sustainable development? How can our work be a factor in increasing economic and political stability? How can we improve the public understanding of raw resources and the need for mining enterprises?"

Jan 1, 2017

"The adsorption of mixed cationic/anionic surfactants with different molar ratios onto quartz was investigated. The cationic surfactant used was dodecylamine bromide (DDA), and the anionic surfactant was sodium oleate (NaOL). The critical micelle concentration values for the individual surfactants and their corresponding mixtures were determined using a platinum plate. The adsorption mechanisms of mixed surfactants on quartz were studied using contact angle measurements, flotation tests and adsorption amount measurements. At alkaline condition, NaOL depresses DDA flotation of quartz without depressing the adsorption of DDA. The molar ratio of mixed surfactants is found to be a key factor in the orientation of alkyl chains and thereby the flotation response of quartz. A mixture of 1/2 or 1/3 DDA/NaOL forms on the surface of quartz when the concentration of NaOL is higher than that of DDA. The adsorption of the mixture decreases the wetting of quartz since the alkyl chains are in chaotically orientation with a conceivable number of head groups directing towards the solution phase. These results provide important insights into the adsorption of mixed surfactants onto quartz surface. INTRODUCTION Froth flotation is known as an effective method of separating mineral particles on the basis of their surface chemistry, specifically their hydrophobicity. [1]. The hydrophobic particles will attach to the bubbles and rise to the top of the containing vessel to form a froth that flows over the lip of the vessel. The hydrophilic particles remain in the liquid [2]. In the process, surfactant is often used as collectors for surface modification in order to change the wetting properties of mineral particles. The primary long chain alkyl ammonium salts are the most widely used as collectors for the flotation of oxide minerals, such as quartz, muscovite, hematite, phosphate and feldspar [3, 4]. Adsorption mechanism of alkyl ammonium salts on oxide minerals has been extensively analyzed [5, 6]. Generally, the ammonium salts are adsorbed through electrostatic interaction of the polar group of the molecules with the surface of these minerals [7]. Despite many obvious advantages of the ammonium salts in low temperature resistance and hard water resisting, however, their unavoidable drawbacks, such as high sensitivity and poor selectivity for slimes, relatively high cost, have limited their applications [8]. In recent years, mixed surfactants have drawn much attention due to their superior physicochemical and surface properties than single surfactants [1, 9-11]. They have been used in many industrial processes such as dispersion/flocculation, flotation, detergent, corrosion inhibition, cosmetics, foods, paints, chemical mechanical polishing, enhanced oil recovery, and nanolithography [12]. Most of the mixed surfactants have synergistic advantage in reduction of the surface tension and critical micelle concentration (CMC); therefore, they exhibit spurious properties, like excellent surface/interfacial activities, and are less expensive than single mixed surfactant systems [13, 14]."

Jan 1, 2016

By S. Frisch

Selenium (Se) in effluent waters has become a significant challenge for a number of industries. Toxicity studies and new reports of occurrence have certainly caused increased scrutiny and actions in the mining industry today (Sandy, DiSante, 2010). While initial activity in addressing selenium-laden waters were conducted in the coal mining industry, today a much broader range of mine types are beginning to search for solutions to selenium treatment of their mining waters, including both hard rock mining operations (gold, nickel, zinc, etc.) and soft rock mining (phosphate, uranium, etc.) Throughout North America, new regulations covering selenium discharge are either in place or being developed. While a number of physical/chemical approaches show promise in selenium treatment, when considering optimal cost and treatment efficacy issues, biological treatment ? particularly fixed-film biological treatment - is reported to be one of the most promising approaches to managing selenium-containing waters. Among biological treatment options, the fluidized bed reactor (FBR) has undergone extensive pilot testing for Se treatment in the last three years, including eight pilot programs, and the first FBR system is now operating at a coal mining site. In all tests, the FBR has been shown to be a highly cost-effective approach to selenium treatment based on its physical and performance characteristics. This is consistent with its history for reaching low levels of treatment in similar service for other oxyanions including perchlorate, nitrate and various metals. With the results from the most recent testing, the technology has been shown to be adaptable to an ever-broadening range of influent water conditions and flow rates, in varying terrains and weather conditions. Selenium occurs in various valence states from -2 to +6 (Sobolewski, 2005). The speciation of selenium plays a critical role in understanding the effectiveness of any approach for removal, especially to low levels. Elemental selenium is insoluble and has little effect on living organisms. Colloidal fractions are known to occur. In aqueous environments such as coal mining runoff, selenium is most often found as the oxygenated anions of selenite (SeO32-, Se4+) and selenate, (SeO42-, Se6+). Selenium is commonly found in mining waters in concentrations ranging from 3 to >12,000 µg/L. The U.S. National Primary Drinking Water Standard MCL is 50 µg/L for selenium (EU 10 µg/L; WHO 40 µg/L). The National Fresh Water Quality Standard is 5 µg/L for selenium. The U.S. Fish and Wildlife Service has recommended that the National Fresh Water Quality Standard be lowered to 2 µg/L to protect fish, waterfowl, and endangered aquatic species. Several states have followed with enforcement actions at these same low levels. In Canada, permits may require stakeholders to monitor levels in water or biota, or to comply with guidelines, at either the National or Provincial levels, which can be as low as 1 or 2 µg/L in surface waters. Treatment of selenium in all mining waters presents a series of challenges. It can be present in relatively dilute concentrations and in streams with variable and often high flow rates. It can be present in many soluble and particulate forms, which may affect process design and treatability. The conditions of influent selenium-containing waters can vary, with issues such as temperature, pH, total dissolved solids and other contaminants affecting the ability to remove selenium selectively and economically. Treatment of selenium often results in the generation of a concentrated by-product requiring disposal, and re-release from residuals can occur. Beyond these issues, the physical environment of a mining operation can offer challenges such as remoteness and harsh and/or cold weather. Currently available selenium treatment technology (Table 1) includes biological treatment and a number of physical-chemical processes ? such as ion exchange, membrane filtration and adsorption ? that vary widely in efficiency and cost. Most treatment options remain either too costly and/or unproven for selenium-containing streams for reasons that include poor removal efficiency, variability in volume and composition of influents, system sizing and logistics considerations, as well as operating requirements.

Feb 23, 2014

By J. D. Forrester

In striving to develop this discussion about "Manpower for Industrial Mineral Industries" two fundamental classes of manpower are encountered. These are: 1) The Labor Force, comprised of unskilled and semi-skilled, nonprofessional personnel who participate in conducting economic, mineral deposit operations and; 2) The Professional People involved in the science, engineering, and management of such industrial enterprises. The commentary given here will be directed primarily to a review of the characteristics of the second or latter class. To pursue successfully a career as a scientist or engineer in today's industrial and social complex, it is necessary that technical knowledge must have been acquired by training and study in an institution of higher learning. Also, to act effectively, the individual must have achieved some degree of specialzation, although this element often is developed to most notable degree by post-graduate exposure and experience. In addition, and especially in the case of "management," it is desirable, indeed it is even necessary, that an individual recognize and appreciate the fundamental humanistic-sociological controls, and their nuances, as these elements exist to shape his total environment.

Jan 1, 1969

By Langtry E. Lynd

The titanium industry is based on the unique properties of titanium dioxide and titanium metal. Because of its whiteness, high refractive index and resulting light scattering ability, titanium dioxide in its two main allotropic forms, rutile and anatase, is the predominant white pigment for paints, paper, plastics, rubber, and various other materials. Titanium metal, because of its high strength/weight ratio and resistance to corrosion, is widely used for aircraft, both in airframes and engines, for powerplant surface condensers, and a wide variety of chemical processing and handling equipment. U.S. production of titanium dioxide pigment in 1979 was about 658,000 tons - 2/, valued at about $770 million. Net shipments of titanium mill products were around 19,000 tons, worth about $380 million. These two major uses account for over 96% of domestic titanium consumption. The third largest application, the use of rutile for coating welding rods, required about 9,500 tons of rutile concentrate, worth about $4 million. Other applications of titanium-bearing raw materials include the manufacture of titanium carbides, ceramics, and chemicals, and the recently developed use of ilmenite as a substitute for barite in well-drilling muds.

Jan 1, 1980

By D. J. Turk

Faced with decreasing production from the gold heap leach operation, Robinson implemented a drilling and blasting program on the leach pads in 1993. This program offset some of the negative effects of low ore permeability and short circuiting of leach solution that resulted in lower than optimum recoveries. The drilling and blasting program created new solution flow paths and increased gold recovery. Production and pulp assays at depth intervals, prior to and following drilling and blasting, reveal the degree of short circuiting and benefits of the program.

Jan 1, 1995

By R. J. Roman

The "mass balance" is unquestionably the most common class of problems for the process engineer'. Closely related, mathematically, is the "heat balance". Every laboratory test requires a mass balance to describe the results. Mass balance calculations can be subdivided into several sub-categories based on whether the results are time dependant or not and depending on whether the input data are measurements that contain errors or are hypothetical values with no errors. Time dependent mass balances are dynamic process simulations and in addition to the conservation of mass constraints require kinetic data input. They are one step beyond simple mass balances.

Jan 1, 1992

By J. E. Lowe

The unique application of a large walking dragline in the mountains of southern West Virginia was developed and implemented by Hobet Mining, Inc. Hobet is an independent operating subsidiary of Ashland Coal and is headquartered at the No. 21 Mine in Boone County, West Virginia, near Danville. Hobet also operates the 07 Mine located in Logan County, West Virginia, near Holden. Both mines are similar in equipment and manpower used; both produce over 2,000,000 tons of clean coal annually. Each site encompasses large, contiguous properties with access to rail service. The larger of the two is the Boone County property; it totals nearly 40,000 acres and has ample reserves. In 1977, Hobet was in the process of constructing a preparation plant (Beth Station) at its 21 Mine site with a capacity for two million tons. One of the first orders of business was to design a mine plan that would provide production for the capacity of the plant. Coal production would come from a more than adequate reserve base using the most economical mining methods available. Hobet looked at different deep and surface mining methods to use in order to develop the property; ultimately, it was determined that the mountaintop removal method with the use of a large dragline was the most economical way to develop reserve. Prior to this time surface mining in mountainous Southern West Virginia was generally done by contour mining and/or augering techniques.

Jan 1, 1993

By Suresh K. Bhatt

A mathematically simulated modeling technique is used in this U.S. Bureau of Mines paper to represent a hypothetical mining operation with existing mining technology and prevalent mining costs. Mining scenarios are prepared and evaluated for potential benefits and costs available through computer-assisted mining. Base criteria, parameters, and methodology are described.

Jan 1, 1991

By Richard H. Follis

Activated carbons used for precious metal recovery from carbon-in­pulp (CIP), carbon-In-leach (CIL) and carbon-in-column (CIC) circuits often become fouled with Inorganic precipitates (i.e., CaCOa, CaS04, SI02), and adsorbed organics (I.e., petroleum distillates from lubricants, dissolution products from wood) (1,2). These contaminants occlude carbon pore structure, such that diffusion controlled adsorption and desorption (elution) of Au(CN)2-and Ag(CN)2· are lmpeded(3,4l. Thus, after only short exposure to the hydrometallurgical environment, the characteristic carbon activity is reduced(5l. By frequently regenerating circuit carbons, activity losses associated with fouling can usually be minimized. Regeneration typically Involves (not necessarily Is this order): 1) elution to remove adsorbed ionic species (e.g., until they are removed from the carbon pore structure, Au(CN)2" and Ag(CN)2-are contaminants )(6l; 2) acid washing with 3-15% (wt/wt) hydro­chloric acid, to dissolve soluble Inorganic precipitates such as CaC03; 3) neutralization and/or water rinsing to remove residual acid; 4) thermal regeneration at 350-650 °C to remove adsorbed and/or pyrolyzed organ­ics; and 5) screening to remove fine carbon particles produced by Impaction and abrasion in the various stages of the hydrometallurgical circuit (i.e., adsorption, elution, and regeneration). The overall process Is purposed to reopen the circuit carbon pore structure, and to maintain the activity and qualities of virgin (new) carbon(7,8l. While most CIP, CIL and CIC operators regenerate circuit carbons, few evaluate the effect of the process on carbon quality in a systematic way. Process control usually Involves Iterating critical regeneration parameters such as: acid concentration; time frames for acid washing and water rinsing; and temperature and residence time for thermal regeneration. Carbon quality control frequently comprises only sporadic activity tests performed on non-representative grab samples dipped from conve­niently accessed carbon storage bins. So, regenerated carbon quality may vary and (at times) be unacceptable for effective hydrometallurglcal circuit operation. To verify the efficacy of the regeneration process and assure accept­able adsorption and elution rates for Au(CN)2· and Ag(CN)2·, operators should systematically assess regenerated circuit carbon quality. This paper, then, suggests methods for effectively assessing circuit carbon quality, Including: carbon sampling procedures; standardized physical and chemical test methods; and criteria and general procedures for comparative adsorption rate (activity) testing. Also, a two tier quality control testing scheme is proposed, and techniques for presenting and interpreting test data are demonstrated.

Jan 1, 1992

By A. Leppala

Scope of the Courier 300 System The fact that reliable on-stream analysis is a prerequisite for effective flotation control is hardly disputed today. Nevertheless, up to now no system has been available that includes all the equipment necessary for successful analysis. However essential an on-stream analyser is in itself, reliable and accurate assaying can only be assured after techniques for sampling, handling the slurries and computing the X-ray data have been developed for the purpose. The Outokumpu Company's Courier 300 System is a complete package that can be installed and handed over with the key. It includes the equipment needed for sampling and handling the slurries. It has been developed from the start to meet industrial demands. Obviously an on-line system must comply with far stricter standards than one designed for a laboratory. Assays are computed by an Outokumpu 316 digital data processor, which is an integral part of the system and controls its entire performance. The computer software is programmed as a standard package, including a highly advanced new model for assay computation. Analysis output is available for a process computer, report typewriter:, and recorders. The package also includes calibration for slurry assays at our pilot installation before delivery. A complete Courier System can analyse up to 4Z slurries and six elements in each slurry. Thanks to its modular design, it can be dimensioned initially to the customer's requirements and is easy to expand later at low cost. Being a mining company itself, Outokumpu has been able to utilize its own long experience in non-ferrous metallurgy - an important factor contributing to the success of the Courier system. History of the project and present installations The first on-stream analyser was installed at Outokumpu'a Pyhasalmi Con¬centrator at the end of 1967, after several years' development. Since then,

Jan 1, 1971

By V. Gangrade, J. Addis, S. Vanderslice

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are conducting research to improve the ventilation of large-opening underground stone mines. The mine ventilation in these mines are characterized by: (1) challenges related to keeping airflow velocities high enough to effectively remove or dilute airborne contaminants, (2) low pressure losses needed to move large air volumes of air, and (3) costly stoppings needed to direct ventilation airflows. Each of two field studies was dedicated to specific focus areas. The first focus area was the characterization of underground mine ventilation airflow. The primary means of airflow control in stone mines is through the use of freestanding booster fans. The primary goal of this study was to identify the effectiveness of various fan types and optimize their placement. Both traverse and grid-based airflow readings were taken at various distances from the fans, ranging from 70 ft to 425 ft away from the fan. The air readings were taken using a vane-anemometer and a handheld hotwire anemometer. The data was used to develop precise computational fluid dynamics models. The second focus area was to determine diesel particulate matter (DPM) concentrations in the mine. For large-opening underground stone mines, controlling DPM exposures dictates the design of the ventilation system. Therefore, researchers carried out the DPM sampling campaign to identify potential areas of concern within the mine. The samples collected during the campaign were analyzed using NIOSH Method 5040. The sampling was done using the Mine Safety and Health Administration’s (MSHA) compliance sampling methodology.

Feb 1, 2023