Search Documents

Rendering a solid hydrophobic and solid-fluid particle* attachment in flotation are recognized as not necessarily related (1,2). The attachment is governed by forces of attraction and repulsion which need to be considered. The induction time required for attachment after solid and fluid particle are brought into proximity (3-8) illustrates the point. Laskowski(8) showed that a reduced induction time favoured flotation but detected no change in contact angle, a standard indication of solid surface hydrophobicity. Induction .time is observed in fluid-fluid particle coalescence, there being called a rest time (9-11) The induction time phenomenon is related to the presence of a metastable liquid film (disjoining film (2)) of the continuous phase (water in flotation) which must thin and rupture to permit attachment. The lifetime of this film, which is governed by the rate of thinning and the probability of rupture with thicknesss, depends on a complex interaction of forces. Investigating these forces should help clarify the attachment process. Practical benefits would be improved understanding of slimes flotation (12,13) This paper is concerned with the role of the mobile fluid particle-water interface on the film lifetime, in particular, the role of time-dependent or dynamic interfacial properties resulting from deformation of this interface.

Jan 1, 1975

By William J. Almas

Operating uranium mill tailings containment and mill decommissioning activities are regulated by the Nuclear Regulatory Commission (NRC) and the Environmental Protection Agency (EPA) through numerous regulatory mechanisms. Reduction of radon emissions from tailings disposal areas, remedial actions to return groundwater to baseline constituent concentrations, and 200-to 1,000-year stabilization of tailings are major focus areas of regulation. The cumulative economic impact and uncertainty associated with regulation are very significant and will hinder future development of uranium milling facilities.

Jan 1, 1991

By William J. Miles

For compliance with the Hazard Communication Standard and other federal and state regulations, numerous minerals, chemicals and products need to be evaluated for crystalline silica content at a threshold of 0.1 %. The polymorphs of crystalline silica that can occur in chemical and mineral products are quartz, cristobalite and tridymite. Other natural, industrial and synthetic amorphous silicas and hydrates must be distinguished from these polymorphs to prevent over-regulation in the workplace and environment. A number of industrial silica products are composed of glasses, expanded perlite, diatomite, slags, and precipitated and fumed silica products. Amorphous silica hydrates used for industrial products, include opal (hydrated silica of biogenic or inorganic origin), perlite, pumice and tuffs. In addition, crystalline and amorphous silicate minerals and chemicals, abundant in nature and industrial products, must be distinguished from the polymorphs of crystalline silica.

Jan 1, 1997

By Isa Nozari, Asghar Azizi

The extraction of copper from sulfate leaching liquor was investigated using Acorga M5640 commercial extractant in kerosene diluent. The effects of important factors such as the extractant concentration, contact time, liquor pH, and temperature were examined on the separation factor Cu/Fe and the extraction efficiency of copper. The results indicated that nearly 92.32% copper was extracted from the leach liquor at 10% (v/v) Acorga M5640 concentration, 1:1 aqueous/organic phase ratio, 20 min contact time, pH 2.5, and 25 °C temperature. Also, the further increase in the values determined had no positive impact on the extraction of copper. Under these conditions, the separation factor Cu/Fe was obtained about 29.64. The extraction mechanism was studied applying the plot of log(D) – 2 pH against log [extractant] and it proved the association of two moles of Acorga M5640 for the extraction of one mole of copper. McCabe–Thiele diagram was constructed and a single-step extraction process was found to obtain themaximumextraction. Additionally, thermodynamic datawere investigated and the extraction process was endothermic and non-spontaneous at 298 K (ΔH = 27.05 and ΔG = 15.52 kJ mol−1). Moreover, the loaded organic phase was stripped and 80.94% copper was recovered after 20 min using 10% sulfuric acid concentration.

Jul 31, 2020

By Douglas R. Shaw

Normal dodecyl mercaptan was evaluated as a collector for flotation of sulfide minerals and precious metals. The reagent is from the class of normal mercaptoalkanes (n-alkyl thiols), and is commercially available in the form of a mixture of n-dodecyl mercaptan and a dispersant, under the trade name Pennfloat(TM)3. Reported are results of bench-scale flotation experiments on many commercially treated base metal and precious metal sulfide ores. Dosages, points of addition, and flotation pH were among the uariables studied. Most notable results were increased copper, molybdenum, and precious metals recoveries. Dosages of dodecyl mercaptan on some ores were considerably lower than required for conventional collectors.

Jan 1, 1979

By I. Iwasaki

A low-grade copper-nickel deposit, with an estimated size of 4.6 billion tonnes and with average analyses of 0.6% copper, 0.2% nickel, occurs in northeastern Minnesota. In addition to copper, nickel, cobalt, and precious metals, the Duluth gabbro contains magnetite, ilmenite, olivine, plagioclase and biotite. It is estimated that the flotation tailings that would be produced by a concentrator of optimal size to sustain a smelter would amount to 20 million t per year. The flotation tailings, having already been ground, warrant a closer examination for the recovery and utilization of potential by-products. The residual sulfide minerals and fibrous minerals may also be isolated and treated separately for useful purposes or for disposal in an environmentally acceptable manner. Two flowsheets were developed; one involving preconcentration by low- and high-intensity magnetic separation and another involving preconcentration by gravity concentration. The concentration methods for recovering and purifying individual by-product minerals were investigated. From their chemical, physical and mineralogical characteristics, the potential areas of application and marketabilities of each product fraction were surveyed.

Jan 1, 1983

Computerized financial models can be used in all phases of the mineral industry from setting exploration targets to projecting profit plans for producing mines. In this presentation, I will use the example of an exploration company entering a new district to trace the application of financial models through the following intermediate phases. 1. Hypothetical analysis and strategy 2. First encounter of mineralization 3. Preliminary drill results - decision process 4. Feasibility studies 5. Post-feasibility negotiations 6. Producing mine 7. Acquisition of producing mines or mineral properties. I will conclude with a brief discussion of the mechanics of the financial models that we use at Wright Engineers Limited. As we progress through the seven phases, the availability and accuracy of the data will parallel the complexity and application of the financial models. However, the same basic financial models are utilized throughout the seven phases. I will begin by suggesting that the exploration group is somewhat autonomous and has the mandate to explore in Western Canada.

Jan 1, 1979

By Michael Moats, Weston Hartzell

The stable domestic supply of gallium, indium, and germanium has been identified as a critical need for the USA. Electric arc furnace dusts processed to recover zinc produce a process residue that could be a potential source of these critical materials. An industrial zinc leach residue was characterized to determine the predominant mineral phases and leached with common mineral acids. Atmospheric agitated leaching using sulfuric acid and hydrochloric acid were examined to determine the extractions of gallium, indium, and germanium as a function of concentration, temperature, and time. Extractions of gallium were found to be similar to iron in all experiments. The maximum percentage of Ga, Ge, and In leached into solution were 82%, ~100%, and 89%, respectively.

Aug 8, 2023

By Jürgen Kretschmann

According to the model of product life cycles, the global coal mining industry is in the stagnation phase. The coal demand of the main consumer, China, has peaked in 2013 and is slowly declining. The Norwegian sovereign wealth fund, the world’s largest, has excluded coal-related companies for ethical reasons. Important players like the UN or the EU have already begun to describe pathways towards decarbonization. Increasing competition between coal mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries like France, Spain, or Germany are only forerunners of this development—their centuries of coal production have been finished. The concept of sustainable development (SD) is fundamentally based on a model of progress where ecological, economic, and social dimensions should be developed equally and positively. But without the idea of competition, the concept of SD is incomplete. Questions arise, such as how can SD be realized on stagnating or declining markets without guarantees for companies “to live forever”? How can SD be a corporate goal in a phase of decline? How can declining mining regions sustainably progress into a better future? The German hard coal mining industry’s lifecycle has ended in 2018 after 60 years of stagnation and decline. As of 2019, all hard coal consumed in Germany will be imported, especially from Colombia, Russia, and South Africa. What has been done in Germany to handle the coal decline in a sustainable way and the lessons learned from this process is described in this paper. It may be useful for mining regions who will face a similar future sooner or later.

By S. R. Brown

A number of relatively recent factors associated with the design of new metallurgical processing plants have made the effective training of operators a requirement for a successful start-up. Some of these factors include large capital investment in a minimum of processing lines, highly complex process control systems, and stringent regulations on plant effluent, to name a few. More than ever, operating mistakes during the start-up phase can lead to substantial delays in achieving design production, as well as problems with government authorities if permit limits are exceeded. The only way to assure your return on plant investment is to ensure new plant operators have the knowledge to properly run the plant from the outset. A comprehensive set of operating manuals specifically targeted for plant operators and foreman, written by experienced operating personnel, is the only effective way to provide the necessary information for start-up-related training.

Jan 1, 1995

By Hasan Ali Taner, Vildan Onen

One of the problems in flotation is mechanical entrainment and the other is the presence of complex gangues (especially clay minerals). In the present study, it was aimed to determine the effects of clay types (kaolinite, illite, and montmorillonite) on mechanical entrainment parameters (total flotation recovery, real recovery, mechanical entrainment recovery, and water recovery). Effects of clay types and clay amount on chalcopyrite flotation were investigated by flotation experiments. Interaction mechanisms between the clay minerals and ore were characterized using SEM–EDS analyses. Experiments were carried out with and without a collector using the mixture of clay minerals and ore under certain experimental conditions. While the clay mineral most affecting the chalcopyrite grade was montmorillonite, the highest mechanical entrainment recovery and the lowest real recovery values were obtained in the presence of illite. While illite is stated as the least problematic clay mineral in the literature, it was determined that illite among three clay minerals used in this study caused significant mechanical entrainment. In contrast, it was determined that increasing the amount of kaolinite did not have a significant effect on mechanical entrainment. This study’s findings will guide in determining of clay minerals’ effect on gangue entrainment in flotation.

Dec 29, 2023

By J. M. Wood

Green algae have been found to be much more resistant to heavy metals than blue-green algae. Several mechanisms for resistance to toxicity have been recognized in laboratory strains of Cyanidium, Chlorella and Chlamycomonas. Cyanidium and Chlorella both grow at low pH in acid mine water. Cyanidium removes metal ions from solution by precipitation as metal sulfides whereas Chlorella complexes metal ions to the cell surface i.e. cell wall) and therefore functions as an efficient ion exchange vehicle. We have shown that Ca2+, Mg2+, K+ and Na+ are of critical importance in both the resistance and bioaccumulation of toxic heavy metals.

Jan 1, 1986

By W. R. Reed, J. D. Potts

This study tests the ability of a new air nozzle system, located under the drill deck shroud, to improve the dust capture of the drill deck shroud. The system consists of three air nozzles supplied with regulated pressurized air and located midway down the shroud in the off-inlet corners of the shroud. Laboratory testing produced operating curves for the system that showed an optimum operating point of 207 kPa (30 psi) and generated respirable dust reductions of 48% to 52% from the drill deck shroud.

Jan 1, 2009

By H. Sevim

Mining engineering curriculum has been discussed and debated in meetings and conferences, and opinions and recommendations have been published in the literature since the inception of the official degree-granting mining engineering program at the Columbia School of Mines in 1864. The deliberations have usually been heightened during the periods of boom-and-bust cycles experienced by the mining industry since the 1920s. Currently, the global natural resource industry is undergoing another cycle, called ?super cycle,? characterized by elevated prices for metals and other natural resources. The super cycle is occurring as a result of the large deficit between the global supply and demand for natural resources, due, in large part, to economic expansion and development in countries such as China, India and Brazil. Because of this cycle, there is a shortage of mining engineers in the U.S., Canada and Australia.

Jan 1, 2012

By John B. Gustavson

Gold was first discovered in Alabama in 1830. Before a decade had passed more than 20,000 people were employed in the various gold districts scattered across east-central Alabama. By 1849 most of the presently defined gold districts were known with such towns as Arbacoochee, Chulafinnee, Goldville, Pinetucky, and Idaho being the principal mining camps. The California gold rush of 1849 signaled the end of intensive prospecting in the Alabama Piedmont for the precious metal. Reactivation of many of the old gold districts has been attempted several times since 1849. Significant activity and development took place between 1874 and 1880, 1888 and 1916, and 1929 and 1936. Locally, some of the development met with moderate succes. The last productive gold mine in Alabama ceased production in 1935. The sharp increase in gold prices since 1973 has caused renewed interest in the potential values of gold of the Alabama gold districts. Most of the gold workings have been abandoned for nearly 75 years and are for the most part inaccessible for convential property evaluation. The early gold miners and prospectors in Alabama were more intent upon finding and mining the valuable metal than in recording their activities for future generations. No matter how interesting or historically significant these records might have been the miners kept no records and left behind them few maps as clues to their activities. Inasmuch as most of the old gold districts have been extensively mined and prospected during the past 150 years, there is very little chance of finding large deposits through conventional outcrop prospecting methods. Similarly, the present geologic knowledge of the various districts is insufficient to launch successful exploration programs looking for large blind lode deposits in new locations within the general gold bearing region.

Jan 1, 1975

By G. A. Irdi

An automated method of microscopy for determining the pyrite size distribution on two base coals that were crushed to 28 mesh x 0 has been developed. Polished epoxy-bound coal pellets were prepared and examined by a Zeiss IBAS image analyzer utilizing a program developed from provided software. Pyrite size distribution determination is considered a necessary first step in pyrite characterization that could lead to successful predictions, by microscopy, of a coal's theoretical pyritic sulfur removal. Our research efforts to date have indicated that the IBP-S can be a reliable instrument for determining pyrite size distribution in crushed coal. A program was also developed to convert pyrite size data to a weight basis for comparisons to the results from chemical analyses. The problems encountered in our research and their solutions will be presented in the discussion.

Jan 1, 1986

By Steve Kral

"The Rapid Excavation & Tunneling Conference (RETC) is a world-renowned event that attracts some of the best minds in the global underground construction and tunneling industry. The experts gather at this conference to impart new technologies, discuss challenges to their projects and learn about new technologies that have become available to them.The 2015 RETC will be held June 7-10 at the Sheraton New Orleans, in New Orleans, LA. This biennial conference, of which SME is a sponsor, is expected to attract about 1,400 attendees from around the world. These professionals represent all parts of the global tunneling and underground construction industries - contractors, engineers, owners, consultants and equipment suppliers.More than 110 technical papers in 21 sessions will be presented over two-and-a-half days. Paid attendees will receive a proceedings volume of the conference. The proceedings will also be available from SME. In addition to the technical programming, the accompanying exhibit will include 155 exhibitors occupying 175 booths, providing RETC attendees the opportunity to get a look at the latest in equipment and service technology. Three short courses will be held on the Sunday preceding the start of the show. And there will be plenty of opportunities for attendees to meet and chat during several social activities that are scheduled throughout the conference."

Jan 1, 2014

The reduced need for traditionally trained and educated personnel in the mining industry is systemic to the changing mining industry. Our universities and other training institutions are doing just fine meeting the traditional skill needs required by the industry. But are the skill needs going to be the same in the near future? The answer may be NO!! Mining is changing: increased liabilities and costs of environmental and safety issues; lower grades of minerals in traditional mining activities; the advent of new bio-chemical processes and robotic equipment as more productive and economic alternatives; and, larger more sophisticated and automatic equipment. Engineering is more specific, accurate, precise and expensive. Measurement is more thorough and timely of progress, production, costs, and productivity. And we will be engaging in more undersea mining, possibly space bases processing, less human interaction, and more remote control of events than was ever thought possible in the past. This paper presents several of the systemic changes that are presently and will continue to change the face of mining. It will identify area where education and management will have to address these changes.

Jan 1, 2011

By J. O. Marsden

This paper presents an overview of the innovative methods for gold and silver extraction that have been put into actual practice in North America since 1987. It is an update of a paper of the same title which was presented by Sass and Mansanti at the AMC conference in San Francisco in 1987. New practices, new equipment and variations of older practices that have been introduced in the last five years are discussed in each of the following categories: process selection trends, comminution, gravity concentration, flotation, oxidation, agitated and vat leaching, heap leaching, solution concentration and purification, zinc precipitation, electrowinning, tailings disposal detoxification, and reclamation.

Jan 1, 1993

By V. Herman, B. Knorr, D. Whalen

"Edge effect is a condition widely observed in High Pressure Grinding Roll (HPGR) operations that gives rise to reduced comminution at the edges of the roll surfaces. This effect is caused by a reduction in the local crushing pressure at the edges of the rolls resulting from the sliding friction between the static cheek plates and HPGR feed material. Practically, this has an impact on equipment sizing, as the edge effect leads to coarser particles reporting to downstream equipment in open-circuit operations and increased circulating load and diminished HPGR circuit capacity in closed-circuit operations.To address this, Metso's HRC™ HPGR incorporates an Arch-frame to maintain a parallel relationship between the rolls and allow for the use of a flanged roll design. We conducted a series of pilot-plant tests with a 750 mm by 400 mm HRC HPGR to compare the performance of the flanged roll design against that of a traditional cheek plate arrangement under similar operating conditions. The edge effect was found to be significantly reduced with the flanged roll design. Based on the pilot-plant results, the implications for circuit design, energy efficiency and overall plant performance in a full-scale application were investigated and discussed.IntroductionGlobal trends such as lower ore grades and rising operating costs are driving the market toward more energy-efficient mineral processing solutions, most notably in comminution circuit design. High pressure grinding rolls (HPGRs) have been recognized as an energy-efficient solution relative to more conventional circuit designs. The basic operating principle of HPGRs, in which a fairly uniform pressure is applied to a bed of material in the compression zone, lends itself to this improved energy efficiency (Morley, 2006). Studies have estimated that savings of 10-15 percent are possible when comparing an HPGR circuit with a traditional SABC circuit (Rosario and Hall, 2008). While HPGRs offer a more energy-efficient solution than tumbling mills, there is still room for improvement in many aspects of the design. Edge effect, in particular, is one such aspect that limits the effectiveness of the machines. Edge effect is the impaired performance at the edge of the rolls due to a reduction in crushing pressure (Morley, 2010; van der Meer, 2010). As described in our prior work (Knorr, Herman and Whalen, 2013), edge effect is caused by the interaction between the ore entering the crusher and the relatively static cheek plates positioned at the edges of the rolls. As the material is drawn into the crushing zone, the sliding friction between the ore and the cheek plates inhibits the ability of material to be effectively drawn into the compression zone at the edges of the rolls. This reduces the crushing force in those edge regions relative to the center of the roll where material is being drawn into the compression zone at a higher rate. In addition, the cheek plates of a traditional HPGR design are held in place by spring-loaded brackets that are adjustable to manage the clearance. This spring-loaded cheek plate design prevents full compression of the material in the edge regions of the roll as there is relief at the outer edges."

Jan 1, 2016