Search Documents

By H. Sevim

Three transportation and handling alternatives for delivering dry coal combustion residues from power plants to underground coal mines were evaluated technically and economically. The objective was to transport, handle, and inject the residues into the old workings of the mine at a minimum cost. This objective was accomplished in two steps: I) Simulation models were developed and utilized in identifying technically feasible designs in each alternative, 2) Technically feasible designs were economically evaluated to obtain the cost-per-ton of material transported. The designs that provided the minimum cost-per-ton were declared optimal An analysis was conducted for varying distances and tonnages to reveal favorable operating ranges of each alternative.

Jan 1, 1996

By Rong Lu, Hao Wu, Bing Dai, Guoyan Zhao, Li Cheng, Weizhang Liang

Affected by the disturbance of blasting activities, deformation instability and rock dynamic disasters are prone to occur in deep hard rock roadways. Thus, it is particularly necessary to understand the failure behavior of rocks and roadways under dynamic loads. In this study, a series of impact loading tests were carried out on sandstone samples with and without a circular cavity by a modified split Hopkinson pressure bar (SHPB) test system. The mechanical properties and energy evolution of the samples were systematically investigated, and the effect of cavity size was analyzed. The results showed that the presence of the cavity in the samples weakens the dynamic compressive strength by more than 10%, and the peak strain and brittleness are also reduced to varying degrees. Under dynamic loading, spalling cracks occur first on the roof and floor of the cavity, and then different numbers of shear cracks are formed on the sample diagonals. The eventual shear failure mode is the result of the connection of the shear cracks and the cavity. As the cavity radius increases, the dissipated energy density and fractal dimension both grow accordingly, leading to smaller and smaller rock fragments. The dynamic failure behavior of the circular cavity can be well explained based on the dynamic stress distribution law. Overall, this study can provide a reference for the study of the mechanism of rock burst in deep roadways.

Feb 18, 2021

By Donald P. Richards

Is a shaft the same as a tunnel and can it be approached in the same manner for design and construction? The most obvious difference between a shaft and a tunnel is that of orientation; whereas a tunnel is commonly near horizontal or slightly dipping, a shaft is commonly vertical or steeply inclined. As a result, design and construction methods employed for tunneling, in general, cannot be directly applied to shafts, although some of the basic concepts of behavior are quite similar. Many of the shafts that have been sunk in various parts of the world are owned by private mining companies. Each company has generally accumulated years of experience in shaft sinking and mining techniques pertinent to its particular geographic location. When a new shaft is to be sunk or an existing shaft deepened, the tendency often seems to be to continue to use the methods that have been used successfully in the past.

Jan 1, 1979

By Richard A. Thomas, III JAMES H. ROWLAND, Liming Yuan

This paper presents the results of large-scale fire experiments on evaluating the performances of carbon monoxide (CO) and smoke sensors at low ventilation velocities. Experiments using three different combustibles — conveyor belt, coal and diesel fuel — were conducted in the experimental mine at the U.S. National Institute for Occupational Safety and Health (NIOSH) Bruceton Research Facility. A total of eight sensor stations were located downstream of the fire with each station containing sensors for CO, smoke, carbon dioxide (CO2 ), oxygen (O2 ), humidity, barometric pressure and temperature, as well as two airflow sensors. The airflow velocity ranged from 0.22 to 0.26 m/s (44 to 51 fpm) in the tests. The response times were recorded for the CO and smoke sensors at each sensor station when smoke and gaseous products of combustion from each burning combustible reached the station. The response times of the CO sensors were used to determine the appropriate sensor spacing in the belt entry with a low air velocity. The performance of the smoke sensor was found to be affected by the high humidity in the experiments. The results on proper selection of sensors and the determination of sensor spacing at a low ventilation velocity can be helpful for ensuring sufficient early fire warning for underground workers, thereby improving the health and safety of miners.

By Y. Akin, M. Hancer, M. S. Celik, J. D. Miller

Flotation pulps with boron minerals such as colemanite and borax using primary amine collectors, e.g. dodecylamine, exhibit collector precipitation above a critical pH depending on the amine concentration. This was earlier attributed to the formation of a mine hydroborate. However, results from this current study indicate that the precipitate is dode-cylamine, rather than dodecylamine hydroborate. A systematic study involving solubility, zeta potential, microflotation, adsorption, and surface tension measurements is presented to elucidate the role of a mine precipitates in boron flotation systems.

Jan 1, 2000

By Y. Wang

Wet magnetic separation methods for recovering hematite and chromite fines and ultrafines are investigated in this paper. These methods include wet high intensity and high gradient magnetic separations, carrier or "piggy-back" magnetic method, magnetic field-induced aggregation and magnetic seeding. This investigation indicates that wet magnetic separation is more efficient for fines and ultrafines whereas other methods can be used to enhance the particle aggregation and/or the magnetic response. The magnetic behaviour of these minerals with respect to magnetizing field, particle size and temperature is also presented.

Jan 1, 1993

By R. S. Hearon

The image of the open-pit miner in the eyes or the Environmentalist has never been very outstanding. The phosphate industry, whose history in Florida reaches back to the late 1800's, can-not be credited until recently with a large number or accomplishments in terms of protection or the environment to change this image. This lack of action was not deliberate or in opposition with the desires of the public. In the formative years, there was little or no public and the companies found it necessary to build towns to house their employees and their families, towns which remained in existence until the late 50's and early 60's or formed the core of present large communities. Neither these pioneers nor most subsequent resource developers considered themselves un-thinking spoilers, nor were they so regarded by their contemporaries. Instead, they acted in a manner consistent with their environmental circumstances and intellectual heritage. Early Americans did make mistakes in using the land but the mistakes became apparent only in the opinion of later generations. Over the past five to ten years, there has been a new self-awareness in the industry with regard to environmental responsibilities brought about, in part by a continuing onslaught of new regulations with jurisdiction over our activities. Part of the new regulations are aimed at industries as a whole while many, particularly state regulations, pertain specifically to the phosphate mining industry. Why all the new regulations? The reasons are encased in a complex web of activity but stem primarily from a new public awareness of its environment. More and more of our youth have become interested in the environmental science areas such as biology and ecology. The tremendous growth rate in both the population and industry has made personal issues out of subjects such as atmospheric inversions and water shortages which previously were abstract concepts. The State has grown from a population of 1,500,000 in 1930 to approximately 9,000,000 people today. This personal impact and general lack of knowledge on the part of the public concerning economics has resulted in big business no longer being held in awe, often in contempt and generally in suspicion where environmental concerns are encountered.

Jan 1, 1978

By B. G. Hicks

The Manapouri Power Project is located in New Zealand's South Island Fiordland. The project is being constructed for the New Zealand Ministry of Works. Construction began in 1963 and is scheduled' for completion in 1969. The project will divert water from the natural, glacially carved Lake Manapouri, at Elevation 580, through vertical- penstocks into an underground powerhouse 364 feet long, 127 feet high, and 59 feet wide excavated about 700 feet below ground surface and about 560 feet below the present lake level. The possible ultimate power installation will produce 700 megawatts from turbines located in the underground machine hall. The turbine flow will discharge through the 6-mile, 30-foot diameter tailrace tunnel into a fiord arm of the Tasman Sea. The rocks in the project area are primarily Paleozoic Fiordland Complex gneiss, schist, amphibolite, and marble intruded by granitic rocks and pegmatite. Shear zones have been encountered in the tunnels and machine hall. These produce water and occasionally require steel support. The machine hall arch was stabilized entirely by rock bolt reinforcement. Rock mechanics instrumentation has been used throughout the project both for pre-construction design calculations and to monitor tunnel rock loads and movements of the machine hall roof and walls. About 28 miles of the 100-mile transmission line will be constructed across glacially oversteepened slopes and debris or swamp filled valleys between the power plant and the eastern edge of the mountainous area. Steep glacially carved rock slopes and locally unstable glacial till complicated construction of the transmission line access roads.

Jan 1, 1968

By Michael David Harmse, Wiehan Adriaan Pelser, Jean Herman van Laar, Cornelius Stephanus Lodewyk Schutte

The South African deep-level mining industry is characterised by high operating costs and narrowing profit margins. Compressed air is commonly the largest consumer of energy in these mines, and any inefficiencies reduce profitability. Various methods aiming to optimise the compressed air networks have been implemented without an ideal economic dispatch strategy due to the lack of compressed air storage. In this study, a genetic algorithm was developed to evaluate the financial benefit of converting underground haulage to act as an air receiver (compressed air storage). By converting inactive haulage of 1.17 km in length into a volumetric air receiver, an annual monetary benefit of R2.5 million ($163 200) can be achieved, with a payback period of fewer than eight months. However, implementing the ideal size air receiver would result in an annual monetary benefit of R7.67 million ($500 700).

Jul 11, 2022

By Marvin P. Barnes

An attempt has been made to compile and code geologic data relating to twenty of the major porphyry copper districts of North America in such a manner as to permit the use of modern electronic digital computers to retrieve, compare, and build statistical mathematical models from the input. In the exploration process as part of his broader efforts to evaluate the potential of some prospective region, district, or ore body, the experienced geologist consciously or subconsciously compares and fits the observed geologic features to similar phenomena associated with known ore bodies with which he is acquainted. Thus an adequate conceptual "model" of the total geologic environment and type of ore body sought is an essential requirement for the successful exploration effort. Numerous such models of porphyry coppers already exist in the minds and notes of many experienced geologists today. These models are, of necessity, couched largely in qualitative terms and though they may be quite definite in the mind of the porphyry copper expert, the total concept of what constitutes a porphyry copper deposit and environment is difficult to convey in very precise terms. There probably is no such thing as a typical porphyry copper deposit. However, it is well understood that most of the deposits that have been studied have many geological characteristics in common. A logical question then might be: What characteristics are most common or how often do they occur in common, and what is their relationship to other common characteristics ?

Jan 1, 1970

By C. S. Compton, T. E. Marshall, D. R. Dolinar, R. Grau, L. J. Prosser, A. T. Iannacchione, D. C. Oyler

Unrecognized roof beam failures resulted in 69% of the falls of ground injuries occurring in underground U.S. stone mines from 1990 to 1996. Field investigations at 45 underground stone mines suggest that excessive beam sag or deflection is the principal unstable roof behavior characteristics associated with miner injuries. Laminated roof structures, common in most underground stone mines, allow the immediate roof to separate into distinct beams. The timely determination of roof beam deflection could provide stone miners with advanced knowledge of potentially hazardous roof. Existing methods to assess roof conditions consist of observational and monitoring techniques. Observational techniques include open drillholes, sounding, wedging, and borescopes. Monitoring techniques include scratch tools, extensometers, telltales, Miners Helpers, and Guardian Angels1. Miners have difficulty utilizing these techniques because roof beams are located an average of 8 m(26.5 ft) above the miner’s head in environments that are dark, dusty and noisy and these deflections are measured in millimeters of movement. To help mitigate the potential for falls of ground injuries to underground stone miners, the National Institute for Occupational Safety and Health (NIOSH) has developed the Roof Monitoring Safety System (RMSS) to aid in monitoring dangerous levels of roof beam deflection. If enough site-specific information is collected and placed on highly visible maps, individual mining operations could establish general guidelines for responding to specific roofbeam deflection occurrences. This would help in implementing a pro-active, comprehensive roof control plan for reducing falls of ground injuries.

Jan 1, 1999

By S. M. Cohen

Roll crushers had been used in the past ahead of existing milling systems in order to obtain additional production from such mills in both the mining and the cement industries. Historically, a roll crusher as a preliminator to a ball mill has been used for a number of industrial mineral applications. Flowsheets, from Taggars(1) show systems for fluorspar, graphite, lead and zinc to name a few, which are shown in Figures 1 to 4. These units applied, (in some cases still in service), prior to 1950 and as early as the 1920's, were of two general types, rigid rolls and spring rolls. The rigid rolls were phased out in favor of the spring rolls. The spring force related to the linear inch width of the rolls, ranged from 500 to 50,000 lbs/linear inch(1) on units up to 90" diameter. With choke feeding, the rolls were spread against the spring force during crushing keeping the system under high pressure to obtain high effectiveness.

Jan 1, 1986

By J. A. Haggman

In a country richly endowed in mineral wealth, Climax Arimco Mining Corporation's (CAMC) Dinkidi porphyry Au?Cu deposit in Nueva Vizcaya province, Philippines, represents the most significant mineral discovery in the country in recent times. The deposit is located within a belt of young intrusive and volcanic rocks in the Sierra Madre mountain chain of north Luzon a region previously unassociated with porphyry-style mineralization. Since 1989, drilling of the Dinkidi deposit has outlined a resource of 124 million tonnes of 1.0 g/t gold and 0.41 % copper. Regional exploration throughout CAMC's 37,000 hectare FTAA has identified a further sixteen potential porphyry-related deposits. A new mining law was passed in March 1995 but prior to that CAMC had the first Financial and Technical Assistance Agreement (FTAA) granted by the Philippine government allowing 100% foreign ownership of mining projects.

Jan 1, 1997

By Santosh Kumar Ray, DEBASHISH MISHRA, Niroj Kumar Mohalik, SOMU MANDAL, Jai Krishna Pandey, Asfar Mobin Khan

Coal is a low-cost and high-calorific-value fuel. The coal mining industry worldwide has been suffering from severe accidents due to coal dust explosion hazards since its inception. Statistically, it was observed that 12,489 fatalities had occurred in 104 reported mining accidents from coal dust explosions during 1900–2020. There are numerous methods for detection, prevention, and control of coal dust explosions in mines. The underground mining environment is unpredictable and has an array of variables. These undulating factors make it difficult to prevent or control the coal dust explosion hazard. However, coal mining is done aggressively throughout the world, especially in developing countries as coal is a major source of thermal energy used in power plants contributing to about 38% (IEA, (2019), World Energy Outlook, IEA, Paris https:// www. iea. org/ repor ts/ world- energy- outlo ok- 2019.) of world electricity. Worldwide, coal dust explosibility studies are carried out in experimental mines, laboratories, and simulations. The complexity, lack of proper infrastructure, and unavailability of laboratory equipment sometimes make it difficult to study coal dust explosibility. The authors have discussed in detail and proposed that the CFD modelling can be a viable option for studying and evaluating coal dust explosibility.

Jun 29, 2022

By Paul Gilmour

"The principal role of the geologist is to recognize the existence of phenomena before trying to explain them" - B.M. Keilau, 1825; A. Holmes, 1965 Some important groups of mineral deposits in the layered rocks of orogenic belts or greenstone belts occur in horizons characterized by the presence of exceptional amounts of silica, iron and carbon, with more or less significant amounts of manganese. Generally, the rocks involved are well banded. In practice, these five physical features - four compositional and one geometric - are found with many lithological guises. Iron formation, in the full, modern sense of the term (James, 1954), quartzite, ferruginous quartzite, chert, jasper, "tetsusekiei" (Horikoshi, 1969), tuffaceous jasper ("purple porphyry" - Anderson and Creasey, 1958, p. 36), ferruginous or graphitic shale, argillite, slate or schist, and hematitic tuff are but a few of the more familiar of the names that have been assigned to these rocks. Widely acknowledged and well-documented examples of metallic deposits found in such sediments include concentrations of iron and manganese and stratabound, polymetallic, massive pyritic sulfides. Less familiar examples include occurrences of asbestos (Miles, 1953; and Coetzee, et al., 1976), antimony (Coetzee, 1976), and perhaps stratabound deposits of Au-Cu-U-W-etc., such as Aitik in Sweden (Mining Magazine, 1975; and Nilsson, 1979) and Olympic Dam in South Australia (Roberts and Hudson, 1983). The case of gold is intriguing. An association between gold and iron formation has been identified at several famous deposits and districts, such as Yellowknife, N.W.T. (Morton, 1979), Homestake, S. Dak. (Sawkins and Rye, 1974), Vubachikwe, Zimbabwe (Fripp, 1976) and the Barberton district, R.S.A. (Hammerbeck, 1976). Yet a critical reading reveals the existence of many other hitherto unsuspected examples. The purpose of this note is to draw attention to that omission and the apparent explanation for it. It is not hard to detect the two most probable reasons for the discrepancy between reality and the record.Most occurrences of gold are associated, not with the familiar banded iron formation or interbedded magnetite and chert (technically, the magnetite-banded variety of the oxide facies), but with the enigmatic carbonate, sulfide and silicate facies of iron formation and/or with rocks evidently related to iron formation. All too commonly, the unfamiliar facies of iron formation have been identified by field and mine geologists and not a few researchers as products of regional metamorphism and hydrothermal alteration, as mafic igneous rocks, or as conventional sediments, ie., without regard to their intrinsically ferruginous nature. The justification for these two complementary assertions is largely to be found in the recognition of a characteristic suite of metals and minerals in gold deposits known to be associated with iron formations. Although, from a geological standpoint, a lithological association is more important than a mineralogical assemblage, the latter is the more likely of the two to be diagnostic. This arises from the different natures of mineral and rock classifications, The identification of a mineral or an element is a matter of fact. Owing to the genetic component inseparable from petrographic nomenclature, viz., "igneous": a rock (believed to have been) derived from a melt, the identification of rocks depends on inferences or conclusions about their mode of formation - conclusions that are commonly debatable and, all too often, involve subjective judgements. This is especially prone to be true, if - as at many of the gold occurrences in question - the host rocks have been metamorphosed and/or "altered". In the notes that follow greater weight has accordingly been assigned to elemental and mineralogical than to host rock composition. In other words, if, in a given gold occurrence, the suite of metals and minerals present conforms to the standards of the subject class, whereas the names assigned to host rocks do not, the latter will be viewed as suspect.

Jan 1, 1985

By D. Brunner

System simulation is an increasingly popular technique for analyzing and improving existing as well as newly designed underground mining operations. An engineering firm that specializes in simulation helped a major metals producer build a long-range planning model of an existing underground mine. Subsequently the team adapted this model to assess technology alternatives in the design of a new mine. The two models differ in the level of detail used for modeling the development process. This paper discusses the differences in approach between the models along with the experiences gained and challenges faced during the construction and use of the models.

Jan 1, 1999

By Samir Kumar Pal, Rajasekar Rathanasamy, Gobinath Velu Kaliyannan, Moganapriya Chinnasamy, Sathish Kumar Palaniappan

The research examines the performance of uncoated and coated tungsten carbide-cobalt rock cutting bits. It aims to optimize process variables (cutting speed, depth, coating material) considering multiple output responses (cutting forces, specific energy, wear rate, material removed, angle of reaction forces). The study uses a hybrid optimization technique combining Taguchi design, grey relational analysis, and fuzzy logic. The optimal parameter combination was found to be cutting speed: 200 mm/s, cutting depth: 6 mm, and titanium aluminum silicon nitride coating.

Apr 24, 2022

By Jiawang Hao, Qinglong Zhang, Liang Han, Chuhan Wang, Shenfang Chen, Lan Qiao

The surface collapse and surrounding rock failure caused by goaf instability are the mining disasters that cannot be ignored. It is of great value to evaluate the stability of goaf accurately and treat it economically for the mine safety and the maintenance of ecological environment. However, in previous studies based on numerical simulation methods, the spatial complexity and the irregularity of actual goaf were not considered. Therefore, based on the internal space data of goaf obtained by high-precision laser detector, the goaf stability was comprehensively analyzed through Plaxis software and two-stage fuzzy judgment theory in this study. To effectively improve the goaf stability, the optimal backfill parameters for the goaf treatment were obtained by a series of mechanical tests. The research results provide some good references for the stability evaluation and the treatment of underground goaf.

Sep 26, 2023

By Madhu G. Ranade

A statistically designed pot grate- kiln test program was conducted to determine the agglomeration process variables necessary for increasing the low temperature disintegration resistance (LTD) and reducibility (R40) of magnetite-based Empire acid pellets. The ASTM tumble index and compression strength were to be maintained at an acceptable level. Six process variables, bentonite addition level, preheat time and temperature, firing time and temperature, and cooling rate, were investigated within the constraints of the Empire plant. The bentonite addition level and firing temperature had the largest effect on pellet properties. The results of this program were verified during a pl ant trial. The target firing temperature at the Empire Plant has been decreased for increasing the LTD and R40 of commercially produced Empire pellets

Jan 1, 1985

By R. S. Conti, M. R. Krump, C. P. Lazzara Ph. D., R. L. Derick, L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, CO, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward-sloping (20%) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward-sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used, due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results.

Jan 1, 2010