Search Documents

By G. J. van der Linde

Foskor operates a mine in the Northern Province of the Republic of South Africa exploiting the igneous complex at Phalaborwa. It produces about 3 million tons of phosphate concentrate per year by means of froth flotation from 26 million tons of ore of which 16 million is mined and milled on site. The remaining 10 million tons originate at the Palabora Mining Company and is pumped as a slurry to Foskor. Two types of ore are mined and milled namely Foskorite and Pyroxenite. (The main mineral content of this ore is Apatite, Phlogopite and Diopside.) After three stages of crushing the ore is milled using 24 rod mills and 5 verti mills. The apatite is then recovered using four stages of froth flotation. The stocks of Foskorite ore are rapidly being depleted and the PMC tailings will also fall away by the year 2002 so that the whole mining operation will then be centered around the Pyroxenite ore. This will lead to substantial increases in production costs. The recoveries achieved in the flotation plant are largely dependent on the successful operation of the comminution section. Parts of this plant are now 35 years old and the advantages of re-engineering, new technology and automation can only be applied to a limited extent in an effort to reduce costs. It was then decided to investigate alternative milling methods, both wet and dry.

Jan 1, 1999

Numerous underground coal mine ventilation seals have been installed in the United States of America prior to 2006 and after implementation of the Mine Improvement and New Emergency Response (MINER) Act. Seal engineering, design, placement, and construction is regulated in industry, but post-construction monitoring of seals is limited to visual inspection of the outby face and seal perimeter, convergence measurement, and atmospheric monitoring. To monitor seal integrity and to provide safe working conditions, a form of non-destructive testing (NDT) is necessary to accurately reflect the health of the seal by detecting post-construction changes, deterioration, or defects within in-situ seals in underground coal mines. Previous research from the National Institute of Safety and Health (NIOSH) has indicated the potential for utilizing ground penetrating radar (GPR) for assessing in-situ mine seals. This paper provides an update to the assessment of proposed NDT methods for seal evaluation using commercially available GPR technologies and systems. Full-scale free-standing seals and large-scale seal specimens were analyzed with an array of GPR units from various manufactures using multiple frequencies.

Feb 23, 2014

By T. Veneroso

Comminution is the process by which rock or ore is reduced to a size where the liberation of the minerals is maximized without changing the chemical or physical properties of the rock. Comminution accounts for about 50% of all energy that mines use (Klein et al., 2018). Growing demands from stakeholders and shareholders for sustainable development and CO2 reduction will increase the need for energy-efficient comminution. Ores with different mineralogical characteristics, textures, strengths, apparent stiffness, and mass-specific fracture energies need to be processed with a specific, new, and efficient comminution technology to increase the production and profitability of mining companies. The adoption of crusher wear parts built with new materials, such as non-Hadfield manganese steel or synthetic materials or traditional manganese with wear-resistant components, could improve the efficiency of the crushers, reduce downtime, increase production, improve the desired P80 (the aperture through which 80% of the product will pass) product size distribution, and enhance mine safety.

Feb 1, 2023

By Jack R. Miller

This session has been organized to suggest to you that the development of direct reduction is important to the iron ore mining and coal mining industries. The papers presented this morning will include a discussion of the costs of making direct reduced iron (DRI), the iron ore and coal supplies needed to produce DRI, the financing of direct reduction (DR) projects and, probably most important, the impact of the DR development on the iron ore and coal industries. For starters, this opening presentation offers a brief statement about DR practice and DRI, under the title that should surprise no one: "Direct Reduction: What Is It?" There is always the chance? that a brief statement may become long and complicated. But, by mixing some slides borrowed from Hal Lownie with a larger number of photographs accumulated from other sources, I hope to avoid such pitfalls.

Jan 1, 1978

By R. A. Jankowski, J. D. Potts

Four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner section averaged 0.59 and 0.26 mg/m3, respectively. The stageloader/crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feederbreaker contributed 0 to 0.2 mg/m3 of dust. A 1000 ft (305 m) increase in belt entry length or a 200 to 500 tons/shift (181,000 to 454,000 kg/shift) increase in production resulted in roughly a 0.1 mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

By R. L. Bullock

For the past 30 years there has been a gradual evolution of mechanical excavating systems in underground hard rock mining applications. This paper traces many of the tests of various tools and methods to break hard rock, up to the present. The tools include impact hammers, boring machines, disc on boom mining machines, disc on revolving wheels and drums, picks and drag bits on revolving hubs, rock splitters, slot cutting systems, and with customized explosives/powder mini-blasting. While the progress has been slow, successes are being achieved in hard rock and more opportunities exist today than ever before.

Jan 1, 1995

By Gordon Cook

American Electric Power Company (AEP operates 31 coal mines in three states, and some 26 electric generating stations (19 coal-fired) located in the Ohio River Basin. Normally the system burns over 36,071,600 tonnes (40,000,000 tons) of coal and generates in excess of 3.6 X 1018 J (100 billion kwh) of electricity per year. In 1975, AEP, in response to the progressively more stringent air quality requirements of the clean air act, acquired large low-sulfur reserves in Carbon County, Utah (Figure 1. Location Map). Price River Coal Company (PRCC) is the operator OF this multi-seam complex, which is part of the Book Cliffs coalfield at an elevation exceeding 1,829 m (6,000 ft.). The topography is mountainous and divided by numerous canyons. Flat areas are at a premium (Figure 2. Castle Gate Area). Modern high production longwall mining takes in some top and bottom waste, and in this particular operation, it amounts to about 14% of the ROM tonnage.

Jan 1, 1983

By Todd Minoski, Matthew McElhinney, Mark Morris, Mark Mazzella, Joseph Bright, Morgan Sears, Craig Compton

To promote the safety and health of U.S. mineworkers, researchers with the National Institute for Occupational Safety and Health (NIOSH) are currently involved in gathering additional field data from the nation’s underground coal mines. The purpose of this field study was to monitor ground movement and changes in pressure during mining where conditions include a thick parting in the coal seam. To accomplish this, three arrays of field instrumentation were installed in the wraparound bleeder of a room-and-pillar panel at the Maple Eagle mine located in southern West Virginia. Borehole pressure cells (BPCs) were used to monitor the change in pressure in pillars located adjacent to the gob. Roof extensometers were installed to measure roof sag at various horizons in the immediate roof, while rib extensometers were installed to measure displacement of the in-seam parting as mining progressed. Additionally, visual observations and manual measurements were taken during subsequent site visits. The repeatability of results, important from a scientific perspective, was accomplished by successfully obtaining field measurements from two nearly identical instrumentation sites. The data collected indicated that the front abutment extent at the edge of the panel was approximately 200 ft, corresponding to a distance of 9– 10 times the square root of the depth. Yielding of the slabbed pillar began when the pillar line was approximately 290 ft outby the instrumentation sites. This was followed by load shedding onto the abutments and the measurement of small amounts of roof sag in the No. 1 entry. Instrumentation data, as presented in this paper, can be used to better understand stress redistribution, pillar performance, and roof/rib displacements. Additionally, this data is suitable for assisting in the calibration of numerical models. Insight gained from applying these models can be used to make better engineering-based judgments for conditions that could potentially be encountered in the future.

Jul 1, 2023

By J. Duran

Mining at Phoenix is currently done by surface operation in the Fortitude and Bonanza Pits, at a combined rate of approximately 110,000 tons per day. A portion of the ore bodies targeted by these pits was mined previously by underground mining methods, dating back to the mid to late 1800?s. Most of the underground workings (voids) are located in the west central area of the Bonanza Pit. The surface operation requires excavation through voids, and there is a risk of pit floor subsidence that has to be addressed. This paper presents a review of the risk mitigation measures that were implemented to reduce risks to people and equipment working in the area.

Feb 23, 2014

By F. H. Seymour

Central to Newmont Gold's Mine planning system is the ability to interactively perform cut and fill operations on topographic contours and to accurately evaluate grades and tonnages within contour outlines using polygon set manipulation routines. This paper develops the applied geometry concepts that underlie these routines. Included are representation of volumes with contours, point in polygon test, block proportion in polygon calculation, polygon area and centroid calculation, and intersection, union, and complement between polygon sets.

Jan 1, 1990

By Ralph van Rijswick, Erik Vlot

"Anglo American operates 18 Weir GEHO piston diaphragm pumps (PD) in the two pump stations of the 52-km (32-mile) long Minas Rio iron ore concentrate pipeline. The pipeline is designed to transport 26.5 Mt/a (29.2 million stpy) of concentrate from the mine to the export terminal at the coast.During the commissioning of the pipeline in the fall of 2014, high pressure pulsation levels were experienced, with peak-to-peak levels as high as 20 bar. Based on pressure readings it was concluded that hydraulic resonances were present in the system, which were excited by the third and sixth harmonic of the flow pulsation generated by the pumps.Based on this observation, Weir Minerals Netherlands, manufacturer of GEHO PD slurry pumps, recommended installing a phase shift controller that controls the phase shift between the crankshafts of the individual pumps, thereby minimizing the effect of the hydraulic resonances.GEHO piston diaphragm pumps and pressure pulsation analysisPiston diaphragm pumps are used worldwide to transport abrasive and/or aggressive slurries against high discharge pressures in the mining, mineral processing and power industries. The basic operating principle of a piston diaphragm pump is shown in Fig. 1.A crankshaft is driven by an external electric motor via a gearbox. The crank mechanism transfers the rotating motion of the crankshaft into a reciprocating motion of the piston. The piston displaces a hydraulic fluid, called the propeling liquid, which displaces an elastic rubber diaphragm. When the piston moves to the right, the pressure in the pump chamber drops below the suction pressure and the nonreturn valve on the suction side will open, allowing the pumped fluid to flow into the pump chamber. When the piston moves to the left, the fluid is compressed, and when the pump chamber pressure rises above the pipeline pressure, the nonreturn valve on the discharge side will open allowing a displacement of fluid into the discharge line. The main objective of the diaphragm is to isolate the piston and the drive mechanism from the abrasive and/or aggressive fluid and create a hermetic seal between the pumped fluid and the ambient environment. Piston diaphragm pumps as shown in Fig. 1 are among the largest positive displacement pumps in the world and have been produced with stroke volumes of up to 100 L (26 gal) per pump chamber for flow rates up to 800 m3/h, discharge pressures up to 250 bar and hydraulic outputs over 2 MW per unit (van Rijswick et al., 2010)."

Jan 9, 2017

By Cody Giroux, Homer Scurlock, Michel Wasag

Silica and Crystalline Quartz exposure continues to be a serious health threat to nearly 2 million workers in the United States, including more than 100,000 working in high risk jobs such as abrasive blasting, foundry work, stonecutting, rock drilling, quarry work, mining and tunneling. The primary focus of this study is to identify the best methodology to reduce particulate-laden air and limit/eliminate exposure to respirable dust with silica/crystalline quartz during tunneling operations. This study focuses on two de-dusting systems employed on similar tunnel construction projects. The first project is the Coxwell Bypass Tunnel located in Toronto, Ontario Canada. The second project is the Westerly Storage Tunnel located in Cleveland, Ohio. The Toronto project is utilizing a wet de-dusting system. The Cleveland project is using a dry de-dusting system. The objective is to determine which system provides the best protection and suitability to capture, remove and ultimately reduce respirable concentrations of silica/ crystalline quartz to safety and healthy levels in underground tunneling activities.

Jun 13, 2021

By Jack Bedder, Nils Backeberg

"Native antimony metal is rare and antimony generally occurs together with gold, lead, copper and silver. There are more than 100 antimony minerals, although the sulfide mineral stibnite is the main economic mineral.Antimony enters the supply chain either as a result of mining (primary production) or recycling (secondary production). China has by far the largest antimony resources and is, as a result, the world’s center for antimony mine production. While China remains the leading primary producer, accounting for 69 percent (80.5 kt or 88,700 st) of the global 117.5 kt (129,000 st) in 2017, market consolidation and regulatory inspections across China leading to closures of facilities have caused a significant decrease in Chinese output from 115.8 kt (127,600 st) in 2015 (81 percent of global production).Tajikistan and Russia are the next largest producers of antimony after China, both ramping up production in recent years. Russia could significantly increase its supply of antimony if Polyus moves ahead with supplying 10-12 kt/a (11,000–13,200 stpy) of contained antimony from gold tailings. Australia and Bolivia are also significant mine producers outside China. The value of the different ores varies based on the metal content of the concentrates, with the most valuable gold-bearing ores sourced from Australia’s Costerfield Mine and the least valuable mercury-bearing ores sourced from the Anzob Mine in Tajikistan. On average, Bolivian and Russian ores trade at an intermediate value between those from Costerfield and Anzob. Nearly all of the rest-of-world production is exported to China, where the ores and concentrates are processed into antimony ingots and oxides.Antimony ingot production is not as widespread as is the case with antimony mine production, owing to the high levels of pollution that are associated with antimony smelting. It is for this reason that smelting has been largely confined to China and other Asian countries ,such as Vietnam and Myanmar, where environmental legislation has historically been less stringent. Tajikistan has become a growing producer of antimony ingot since 2014, coming from the commissioned metallurgical plant at the Anzob Mine.Antimony oxide production is undertaken on four continents with China being the biggest producer. There is also a considerable amount of oxide production in Europe (mainly Belgium and France), which relies on imported antimony metal feedstock, mostly from China.A new antimony project under construction by Strategic and Precious Metals Processing (SPMP) in Oman made progress in 2016 and 2017, and after producing first metal in April 2016 in test facilities, was set to be commissioned in the first quarter of 2018. Commissioning had been moved back to June 2018, with a potential ramp-up to 2-3 kt/a (2,200 to 3,300 stpy) of antimony metal by the end of 2018. SPMP is also reviewing producing antimony oxide as part of its flow sheet."

Jan 7, 2018

By E. Stolarski

The circulating fluid bed (CFB) technology can proudly point to its history of more than a quarter of a century of commercial operations. Over 80 CFB units operate in aluminum calcining, coal combustion and gold roasting. This paper describes the invention of the circulating fluid bed and chronicles its development and evolution from calcining through coal combustion to gold roasting. It presents performance data of Lurgi's CFB units in operation and highlights the six gold roasting plants currently operating throughout the world.

Jan 1, 1998

By Amila Sandaruwan Ratnayake, T. Dilmi. U. Wijewardhana, H. C. S. Subasinghe

The value addition potential of ilmenite was examined using several characterization techniques. Raw ilmenite is composed of 93.65 wt.% of FeOTiO2, 3.55 wt.% of SiO2, 1.22 wt.% of Al2O3, and the remainder being other minor oxides. Ilmenite and powdered carbonized coconut shells were mixed in the weight ratio of 4:1. A separate fraction of the same mixture was added with powdered seashells in the weight ratio of 4:1:0.5. Six fractions of each mixture were distinctly milled from 1 to 6 h in a planetary ball mill. XRD spectra (broadened and diminished reflections of ilmenite) and FTIR observations (Ti―O―Cbonding) of milled samples indicate the possible incorporation of carbon into the ilmenite structure. Any clues of an occurrence of new rutile peaks were not observed in XRD spectra of milled samples. Consequently, the carbothermic reduction has not been initiated during mechanical activation. In this case, samples powdered for 6 h in a mill were isothermally annealed for 2 h under normal airflow at temperatures of 800 °C, 1000 °C, and 1200 °C, respectively. According to the X-ray diffractograms, the annealing temperatures of 1000 °C and 1200 °C exhibited almost similar trends with rutile (R), pseudobrookite (PB) and elemental iron (F), and a very few ilmenite (I) peaks. Consequently, 6 h of milling and 1000 °C annealing were concluded as the optimum conditions for the carbothermic reduction. Moreover, this study indicated seashells as a potential rate raiser for the carbothermic reduction of ilmenite at 800 °C. Therefore, this process is applicable to upgrade ilmenite into a mixture of synthetic rutile and elemental iron.

Mar 29, 2021

By CASSANDRA L. HOEBBEL, Emily J. Haas, MARGARET E. RYAN

In recent years, there has been increasing interest in the role that individual factors play in health and safety (H&S) outcomes in the mining industry. Two surveys, one measuring self-reported routine safety performance and one measuring individual perceived competence in the non-routine knowledge, skills, and abilities (KSAs) critical to emergency response, were administered to two samples of mineworkers in separate research studies over a 2-year period (N=2,020 and 696, respectively). Eight demographic items were common to both surveys and their associations with each performance outcome were tested in response to a series of exploratory research questions.

Jan 9, 2022

By M. A. Evanto

Since the late 1970's, the Roof Control Division (RCD) of MSHA's Technical Support has been performing linear analyses for the enhancement of miners' safety. This remote sensing process uses Landsat data to predict areas of potentially hazardous ground conditions in underground mines. To date approximately 700 analyses have been completed by the RCD, with nearly 75 being performed with the current equipment, software and methodology which was updated in early 1995. While success is difficult to measure, requests for linear analyses continue to come from large and small mining companies which suggests the industry's acceptance of the process.

Jan 1, 1998

By N. W. Johnson

The behavior of non-sulphide gangue in chaloopyrite flotation circuits has been investigated. Plant and laboratory tests were carried out on five different ores, and linear relationships were found to exist between the rates of recovery of water and free nonsulphide gangue in the concentrates although there was evidence from pilot plant tests that these were linear approximations to parabolic curves over the limited regions which were observed. There was evidence that the free non-sulphide gangue enters the concentrate by hydraulic classification and a classification function has been proposed to define this behavior. This function is suitable for inclusion in a mathematical model of the process.

Jan 1, 1972

By VIVEK KASHYAP, PATRICK TAYLOR

The presence of iron in sphalerite induces the formation of zinc ferrite (ZF) during roasting. Zinc refinery residues (ZRR) and electric arc furnace dust (EAFD) contain a significant amount of zinc ferrite and are difficult to treat. According to the literature, up to 71% ZF has been found to be present in ZRR. The dissolution of zinc ferrite is inefficient even in aqua regia. The Waelz process is an existing process to recover zinc from electric arc furnace dust by reduction using carbon monoxide followed by the volatilization of zinc. In this study, zinc was selectively extracted from zinc ferrite by partial reduction of zinc ferrite at relatively low temperature followed by leaching in dilute sulfuric acid (20 g/L). Pure zinc ferrite samples were partially reduced to zinc oxide and magnetite by using H2 gas as a reductant. The presence of magnetite and zinc oxide was confirmed by X-ray diffraction (XRD) technique. A maximum of 95%zinc extraction was achieved after leaching with sulfuric acid on the reacted samples. The paper also discusses the effect of time, temperature, and concentration of H2 in the reducing gas on the extraction of zinc and iron from ZF.

Sep 16, 2020

By S. Deming

Coal is China's main source of energy. In 1988, 76.1% of commercial energy consumption was supplied by coal. To provide a rational utilization of its coal resources, China has paid considerable attention to coal preparation over the last 10 years. In 1980, there were only 105 washeries treating about 100 million tonnes of coal, but by 1988 there were 151 washeries treating 171 million tonnes per year. This paper describes the development of China's coal preparation industry; its growth, the equipment, and the technology. Statistics and information on the current status of the industry are also be presented.

Jan 1, 1991