Search Documents

By Jens Classen, Martino Gatti

"GENERAL PROJECT DATAThe Sparvo Tunnel is part of the “Variante di Valico” project, a new 65km (40mi) highway link between Bologna and Florence, designed to renew the existing A1 route which connects Bologna and Florence. It is composed of 2 x 2,5km (1,55mi) twin tunnels excavated inside a complex geological context, characterized by the presence of a series of surface landslides and methane gas.The inclination is 2,6 % and the minimum radius is 1.400m (4.600ft). The two tunnel tubes were excavated by a 15,6m (51ft) diameter EPB-TBM from summer 2011 to summer 2013. The internal diameter of the concrete lining is 13,6m (44,5ft), made up of precast concrete segments 2m (6,5ft) long and 70cm (28”) thick, being the largest and heaviest segments ever produced. Excavation went smooth apart from initial problems concerning clogging problems and a main bearing damage of the TBM, which are discussed in a further paper during the congress. No structural damage was observed until the end of the TBM drives.SITE OBSERVATIONS DURING THE POST-EXCAVATION PHASEThe first evidence of the stress state of the segmental lining appeared on November 20, 2013 inside the northern tube (1st drive). Ring No. 884 showed obvious signs of overstress, resulting in spalling and crushing of the concrete, and the subsequent bending of the reinforcement, as visible in figure 1.At this time the tunnel invert was already partially backfilled, and construction traffic was running through the tunnel. First safety measures included closing of the tunnel, and initial measurements of the displacements."

Jan 1, 2016

By Marcelo de Oliveira, Antoine Allanore, Dennis P. Chen, Davide Ciceri

Potassium fertilizers (potash) are mined in a handful of countries in the Northern Hemisphere. Potash is either expensive or unavailable to the farmers of the Southern Hemisphere. Alkaline alteration of K-feldspar rock (ultrapotassic syenite) in autoclave in the presence of Ca2+ generates a mixture of K-bearing calcium-aluminum-silicate-hydrate (C-A-S-H) minerals that potentially can be used as an alternative local fertilizer. This work investigates the effect of processing temperature (200 °C, 220 °C, and 230 °C) and time (from 0.5 to 3.0 h) on pH, mineralogy, and elemental availability of the C-A-S-H mineral mixture. Increasing temperature results in an increased conversion of K-feldspar and increased content of both the mineral tobermorite (Ca5Si6O16(OH)2·4H2O) and amorphous phase in the resulting C-A-S-H mixture; increasing time results in an increased conversion of α-dicalcium silicate hydrate into tobermorite. The amount of K leached from the mixture is relatively constant across all processing conditions. Hydrothermal alteration in autoclave of K-feldspar-bearing rocks such as ultrapotassic syenite permits the synthesis of a potential potassium fertilizer which alkalinity and mineralogy can be tailored according to soil requirements.

May 22, 2020

By M. Schlegel, J. A. Villa Mena, R. E. Vivas

ArcelorMittal, headquartered in Luxembourg, is one of the world’s largest steel and mining companies. It supplies steel to industries such as automotive, construction, and energy, with a strong emphasis on sustainability and innovation. The company employs about 125,000 people and, in 2024, produced 42.4 million tons of iron ore and 57.9 million tons of crude steel across 15 countries. Its mining operations span Canada, the United States, Mexico, Brazil, Ukraine, Bosnia and Herzegovina, Kazakhstan, and Liberia, focusing on iron ore and coal extraction to support steel production. This study examines Peña Colorada, one of Mexico’s largest iron ore mines (a joint venture by ArcelorMittal and Ternium). Facing declining ore grades, Peña Colorada adopted Hexagon solutions to uncover and capture project value. A comparison of two Life of Mine (LOM) plans from 2012 and 2016 (before and after implementing Hexagon solutions) shows that between 2019 and 2023, Peña Colorada reduced actual waste by 26% (compared to 2012 LOM) and 19% (compared to 2016 LOM). LOM Plans are generated yearly, and each time, opportunities for reducing mining waste were identified, evaluated and implemented. The key driver was schedule optimization using Hexagon MinePlan Schedule Optimizer (MPSO). This reduction means less waste transported to disposal sites, resulting in fewer hauling equipment operating hours, lower fuel consumption, and reduced carbon emissions.

Feb 22, 2026

By Lyman File

This paper discusses the overall challenges to construct a two-lane highway tunnel located in southwestern Colorado on U.S. Highway 160 for the Colorado Department of Transportation by the Kiewit Western Company. The purpose of this project is to provide the excavation and temporary support for a highway tunnel 280 m (916 feet) long. The tunnel cross section is 14.3 m (47 feet) wide by 8.5 m (28 feet) high, 105 m2 (1,130 SF).Construction methods include conventional drill and blast excavation with rockbolt and shotcrete ground support. This unique tunnel is being constructed under alpine tunnelling conditions and in the immediate vicinity of active highway traffic.

Jan 1, 2003

The primary use of coal in the US is for electric generation. The problems associated with the use of this vast amount of coal is the central theme of these sessions. The problems discussed include: production capacity, mining problems, coal cleaning, transportation, combustion, and various environmental problems, such as health effects of coal combustion, water and air pollution, and solid waste disposal.

Jan 1, 1979

By Y. Luo

Highwall mining, which is a relatively new mining method, is a preferred and often the only feasible method for extracting coal reserve left by surface mining operations in areas with steep terrain and in closely spaced thin coal seams. Though its safety record is comparable to that of surface mining, failures of mine structures in highwall mines, especially the highwall, have occurred. Methods for the systematic designing of highwall mines to meet the safety and operational challenges are still evolving. This paper presents the results of research into improving the existing design methods and developing new ones for highwall mining operations. The design methodology is aimed at ensuring structural stability of the highwall, roof, web and barrier pillars and preventing subsidence. It takes into consideration the major ground control challenges of soft and layered mine roofs, and interactions from mining closely spaced coal seams. An optimization design process applying a pressure arch concept can be incorporated to improve the recovery rate of coal reserve. A computer program based on the design methodology was developed.

Jan 1, 2015

By LeRoy D. Loy

To facilitate effective land reclamation and comply with existing state regulations, surface coal mine operators have in recent years adopted new mining techniques and equipment utilization for steep-terrain mining. In contrast to direct spoiling with draglines or shovels, these new mining methods require some form of overburden haulage from the excavation face to the point of reclamation. Although current mining methodologies such as Block-Cut, Modified Block-Cut, and Mountaintop Removal with Head-of-Hollow Fills have proven effective in achieving reclamation objectives, some production problems have resulted from pit congestion and excessive equipment delays. Recognizing this problem, the United States Bureau of Mines contracted Skelly and Loy to design innovative mining concepts utilizing conveyor haulage in place of trucks, loaders, dozers and scrapers. Project objectives required definition of current bottlenecks and development of mining systems to: alleviate bottlenecks; increase production potential; facilitate additional resource recovery; enhance reclamation; reduce safety hazards; and improve mining economics. Successful completion of project goals within a four year program involves systematic implementation of the following separate work phases: 1) Develop Concepts for Block-Cut Mining Systems; 2) Determine the Economic and Technical Feasibility of Concepts; 3) Prepare Detailed Design and Specifications of Concepts; and 4) Prepare Specifications for Conducting Field Tests of the Most Promising Concepts. At the time of this publication, Phases 1 and 2 are finalized with Phase 3 efforts well underway.

Jan 1, 1977

By Alden B. Carpenter

Oil-field brines have been collected and analyzed from Jurassic and Cretaceous rocks in the Mississippi Salt Dome Basin, from Jurassic and Lower Cretaceous rocks, southwestern Arkansas, and from Ordovician and Silurian rocks, southern Michigan. All of these brines are genetically related to evaporites and appear to be brines expelled from halite-bearing rocks, presumably during compaction. The brines in rocks closest to the halite-bearing rocks are uniformly low in lead and zinc suggesting that the metals in metal-rich brines are not acquired within evaporite sequences. The metals in metal- rich brines in Mississippi and in Russia appear to be derived from red beds and may have been originally associated with ferric iron oxyhydroxides. Reduction of these compounds by migrating hydrocarbons appears to release lead and zinc to the associated brines accompanied by the fomation of authigenic ankerite.

Jan 1, 1979

By J. Hupka

Some aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20 kg tar sand samples (Asphalt Ridge and Whiterocks, Utah), and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity, and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus the tar sand porosity is an important variable which determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, and still not complete after 15 hours regardless of the ambient temperature.

Jan 1, 1992

By Jack E. Bailey

From a start in 1957, milling 3,000 TPD of copper ore, the Cyprus Pima Mining Company, which is located 20 miles south of Tucson, has expanded its operations four times, and is currently treating over 55,000 TPD of ore.1 The most recent expansion added a 14,000 TPD semi-autogenous concentrator to the operation. Shortly after startup in January, 1972, the semi -autogenous plant exceeded the designed tonnage rate.2 Ore from the mine is delivered to a 54 inch gyratory crusher and is reduced to a minus 8 inch product. From the crusher the ore is stacked on a surge pile and then reclaimed and fed to the two parallel grinding circuits. A 28 ft. diameter by 12 ft. long semi-autogenous mill and a 16.5 ft. diameter by 19 ft. long ball mill make up each grinding circuit. The semi-autogenous mills are in closed circuit with screens and the ball mill circuits are closed with hydro- cyclones. Rougher flotation follows the grinding operation. Concentrate regrinding and cleaner flotation is performed in Mill I, the older mill. The generalized flowsheet is shown in Figure 1.

Jan 1, 1975

By R. M. G. Machunter

The presence of ultra-fine particles affects the separation performance of wet gravity separation equipment. Several studies have been undertaken to establish the maximum level of these particulates that can be tolerated by spiral separators and it has been found that unless the ultra-fine material is effectively processed, relatively low proportions in the ROM material combined with high feed rates can result in degradation in plant performance and/or excessive water consumption. The maximum level of particulate material in the process water has been determined by examination of separation performance of spiral separators under varying slime loading. This work has been conducted utilizing various feed sources and a robust ‘rule-of-thumb’ has been derived.

Jan 1, 2005

By John H. Bassarear

The never ending search for lower unit costs led Pima Mining Company's management to study various alternatives shortly after Expansion III was completed. It soon became apparent that a considerable amount of ore assaying 0.35% copper had to be moved in order to maintain mill feed at the desired 0.54% copper content, which is the overall grade of the ore reserves. Detailed investigations revealed that for a period of 8 - 10 years, about 14,000 tons per day of 0.30 - 0.40% copper ore would pass by the crusher en-route to the low grade stockpile. This ore is very hard, very clean and has to be mined at a relatively uniform rate. A six month pilot plant run testing autogenous and semi-autogenous grinding gave very encouraging results. Since no mining costs need to be charged to the extra tonnage (it had to be mined anyway) the only major costs would be against milling. The decision to proceed was made in August 1970 and Fluor-Utah was retained as the prime design construction contractor. Ore was first put through the new mill on December 29, 1971. By March of 1972 design tonnage of 14,000 TPD had been attained. The first three expansions at Pima Mining Company, 20 miles south of Tucson, increased mill capacity from 3,000 TPD to 36,000 TPD. These expansions included a separate, conventional, three stage crushing plant plus additions to the existing concentrator that primarily duplicated the then current flowsheet. Expansion IV, however, consisted of an entirely new and separate primary crusher and a completely new mill building located about 2,000 feet southeast of the 01 d concentrator. The new mill, using semi-autogenous grinding, produces scavenger and rougher flotation concentrates that are pumped to the old mill for regrinding, cleaning, thickening and filtration.

Jan 1, 1973

By James E. Lawver

At the present time, the Florida phosphate industry is experiencing one of the worst marked slumps in its one hundred year history. Recent agriculture over-production has caused low grain prices such that the net income of U.S. farmers is expected to drop to its lowest level since the 1932 depression. The farmers' low income, along with high interest rates that preclude them from borrowing to purchase fertilizer, make the immediate U.S. phosphate market outlook bleek at best. The export outlook is also pessimistic due to world recession and the U.S. dollar's high exchange rate. In June, 26% of the phosphate industry's workers were laid off for an indefinite period of time. Despite the immediate painful slump, the long-term outlook for the industry looks good. Florida has enormous reserves and will continue to produce a third of the world's phosphate supply simply by making changes in the present system of mining, beneficiation, waste disposal and land reclamation.

Jan 1, 1983

By B. P. Sullivan

This paper describes how the author projected the economic benefits of a proposed coal liquefaction project based in Pennsylvania. These benefits were assessed in a successful effort to garner government support for the project. The projections considered such issues as increases in employment, wages, and tax receipts to state and local government, plus other less-obvious benefits, such as site remediation. The paper explains how sponsors of similar projects can use economic projections in making meaningful and compelling presentations to federal, state and local authorities.

Jan 1, 2000

By G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology, including such factors as thermal and chemical stratification, turnover and the development of anoxic conditions with depth. Limnologic data collected from four existing pit lakes in Montana and Saskatchewan indicate that pit lakes develop a thermocline (temperature stratification) in the upper 10 to 30 m (33 to 100 ft) of the water column. Two o f the pit lakes, 26- and 55-m (85 and 180 ft) deep, undergo seasonal turnover of the entire water column, whereas two deeper, pit lakes, 110 and 240-m (360- to 790 ft) deep, undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column, and a distinct chemocline develops with depth.

Jan 1, 1997

By James H. Boettcher

In the second quarter of 1979, ASL Inc. inquired whether Crocker National Bank ("CNB") would provide $4 million in term loan financing to help ASL acquire the outstanding shares of the S&S Coal Company in West Virginia. ASL had, prior to approaching CNB, sought financing with the assistance of a financial advisor from a number of commercial banks without success. A summary of the initial terms requested by ASL is shown in Table I compared with the actual terms the transaction closed with. It is not difficult to note that the two sets of terms differ significantly. This is often the case when financing requests based on the expectations and vision of a mine developer are juxtaposed with more pragmatic requirements of a commercial bank. The "art" and fun of structuring financing plans for mining ventures (highly leveraged acquisitions or grass roots) comes in working with mine developers to arrive at a final financial structure that meets their objectives and constraints as well as those of the bank or other financial institution providing much of the financing. This article briefly describes the process we went through with ASL beginning with the terms they requested initially and ending with the ones on which the transaction was finally closed.

Jan 1, 1981

By B. L. Gibbs

The mining industry is constantly in a state of flux -boom or bust; mine openings and closings. Part of the reason is the nature of ore deposits -they are there or they are not. Once they are mined, they are reclaimed and the move is on to the next deposit. Risks are usually high, and payoffs can be great or not so great. Many factors go into making a property payoff, and mining companies are continually searching for ways to remain profitable as long as possible. Computers and the people who can make them work are one of the ways available to improve productivity and ensure this happens. Computers have been used in the mining industry for the last 30 years (and more in a few cases). During the past 10 years, the explosion of micro-computing has changed how many mining companies do their work.

Jan 1, 1993

By A. T. Stroebel

Diatomite deposits, the skeletal remains of tiny aquatic plants called diatoms, are found in many parts of the world. Only a few of these de- posits are of commercial value. Open pit mining is used in nearly all deposits now being worked. Processing methods range from simple drying, crushing, sizing and packaging to carefully controlled and highly sophisticated calcining and air classification procedures, employing the latest control and testing techniques. The major uses of processed diatomite are in filtration as filter aids and fillers and extenders.

Jan 1, 1979

By S. Dawson

The Republic of South Africa has become a major producer of opencast coal in recent years. Opencast production commenced in 1970 and by 1977 some 10 million run of mine tonnes were being produced annually, Since then surface mine activity has increased to more than 60 million tonnes which represents approximately one third of the total annual South African? coal production. Whilst a substantial portion of this production is exported, the majority is used in the domestic market, The largest consumer, being the South?\ African Electricity Commission (Eskom), produces most of South Africa's electricity using coal fired power stations,

Jan 1, 1990

By R. R. Kallu

The current 120 psi seal design and evaluation practices are mostly based on simple analytical solutions. Considering the simplistic assumptions and limitations involved in simple analytical solutions and practical difficulties involved in conducting conventional full-scale explosion tests for evaluating 120 psi seal designs, there is a need for developing new scientific methods and engineering practices for design, analysis and evaluation of mine seals.

Jan 1, 2010