Search Documents

By J. F. Stenebråten, W. P. Johnson, D. R. Brosnahan

Carbonaceous material (CM) from ores of varying preg-robbing activity from Barrick Goldstrike Mines Inc. (BGMI), Nevada, was characterized in terms of its functional group content, hydrocarbon content, elemental composition, and humic acid content. FT-IR analyses showed neither the presence of hydrocarbons nor of carboxylic, phenolic, or sulfhydrol functionalities. FT-IR bands present included C=C stretching in aromatic rings and C-O-C stretching, indicating presence of oxygen as ether linkages in the carbon matrix. Calculated atomic oxygen to carbon (O/C) ratios did not reveal a trend between maturity of CM and preg-robbing behavior, possibly due to low resolution of electron microprobe analysis. However, the atomic O/C ratios agree with other chemical analysis, indicating that the organic carbon is very mature, similar to or higher in grade than anthracite coal.

Jan 1, 1999

Tunnel damage from explosion and earthquake excitation is correlated with strain and particle motions. Critical strains and motions are then correlated with focal distance, which is so small that permanent strains are highly likely. The shaking process is then numerically modeled to investigate the effects of excitation frequency and joint orientation. The models confirm that near cavern blocks slide intermittently only at relatively high particle velocities during periods of low joint normal stress. Larger displacements occur with relatively small shear wave lengths or relatively high frequencies. Variation in joint orientation and rock mass dilation result in changes in displacement.

Jan 1, 1985

By A. D. Davis

The former Homestake gold mine at Lead, South Dakota, has been selected by the National Science Foundation as the proposed host site for the Deep Underground Science and Engineering Laboratory. The deep laboratory and associated research campus will be developed at approximately the 7700-ft level. Plans also include the development of the Sanford Underground Science and Engineering Laboratory at the 4850-ft level. After the mine?s pumps were shut off in June, 2003, water levels rose to approximately the 4650-ft level by early 2008. Pumps in the 8150-ft deep mine were turned on again for dewatering in April, 2008. Instrumentation is being installed in the mine to measure water-level declines during pumping, for later analysis of permeability and related hydraulic properties of the formation. Pressure-sensitive transducers and data loggers will provide real-time information on water levels that will be available to interested parties. Quality of the water also will be monitored as it is pumped from the mine. I

Jan 1, 2009

By Michael V. Mergentime, Prakash M. Donde

The Nutley Quarry Trunk Sewer Project is a good example of a tunnel that went through difficult and complex ground. The 2 m (7ft.) diameter and 840 m (2,750 ft.)long tunnel passed through soft ground, mixed face, and hard sandstone. The soft ground and mixed face tunneling provided several challenges. During excavation of the tunnel, the Contractor encountered a number of unanticipated large boulders. In addition, the length of the mixed face portion of the tunnel increased by 100%. The Contractor tried various construction techniques to overcome the difficult ground conditions and complete the project. The tunneling progress was slower than expected. The Contractor claimed extra costs for differing site conditions. Through discussions and negotiations between the Contractor, Engineer, and Owner, all of the changed condition claims were settled before the construction of the project was completed. This paper addresses the difficult ground conditions, claims evaluation, and how they were resolved by cooperative efforts between the Contractor and the Owner/Engineer.

Jan 1, 2001

Resolution Copper Mining LLC (RCML) is currently in a Pre-feasibility study evaluating a large and deep copper and molybdenum deposit in the historic mining district east of Superior, Arizona. Work scheduled for the next several years includes dewatering the existing shut-down mine (the Magma Mine) and sinking an exploratory shaft to 2,130 meters (7,000 feet) below the surface. To dewater the Magma Mine and sink the exploratory shaft, RCML must extract and manage about 2 billion gallons of accumulated mine water inventory, as well as about 300 million gallons per year of new inflow. In order to conserve a valuable water resource in a desert environment, RCML worked with the New Magma Irrigation and Drainage District (NMIDD) to provide treated mine water to blend with and supplement the NMIDD?s water supply to approximately 2,000 hectares (5,000 acres) of farmland located east of Phoenix. A 44 km (27-mile) pipeline was needed to convey the treated water. It was essential that a treatment system be used which could reliably meet irrigation water quality goals, produce a non-scaling effluent to maintain pipeline flow capacity, and generate a dense sludge minimizing disposal cost and volume. This paper describes the resulting mine water treatment and recovery system (MWTS) and how the system has performed against objectives.

Jan 1, 2011

By James J. Scott

I welcome this opportunity to speak before the Coal Division of the AIME in such an attractive setting as the Pacific Northwest. With the development of the Centralia project, the Pacific Northwest will have its first major coal-fired thermal electric generating plant. This State has a long history of coal mining that diminished with the passage of coal-fired steamships and locomotives but is now reviving with the growth of electrical power demand. Because this 1,400 row plant is to be supplied with surface-mined coal, it is particularly appropriate that this area be the setting for a talk on factors influencing the growth of surface coal mining in the West. During the course of my talk, I will touch on a number of factors including electric power demand, coal resources, production trends, environmental considerations and trends in State and Federal activities that I feel will influence surface coal mining in the West. Total electric power consumption by the year 2000 is expected to reach 9.4 trillion kilowatt-hours. Predictions of total coal consumption for electric power generation by that year range from a low of 845 million tons to a high of 1,520 million tons, or 2.6 to 4.7 times the amount used for this purpose in 1970.

Jan 1, 1971

The OptiPit® software program is developed based on expertise gained at the Colorado School of Mines (CSM) using Mixed Integer Linear Programming (MILP) techniques. This program has been developed to satisfy the need in the mining industry for a multi-time period schedule and cutoff grade optimization tool that handles large scale open pit and underground mining operations involving many dumps, stockpiles, complex processing options and blending requirements. The current software (or earlier development versions) has been beta tested and used on various large scale projects within Placer Dome Inc., Newmont Mining Corporation, and Phelps Dodge Corporation since 2003. Through the use of this software, these companies experienced additional value creation by optimizing mine sequences, cutoff grades, material process flows and stockpiles under complex operational and processing constraints. This paper will present simple case study results to demonstrate the power of OptiPit® when used as a cutoff grade optimization tool. Furthermore, the paper will show, by example, how significant the difference in the Net Present Value (NPV) of a given project can be, depending on whether results are obtained by way of cutoff grade optimization using OptiPit®, or by using traditional breakeven cutoff grade approach.

Jan 1, 2007

By E. Snyders

Two alternative processes for the manufacturing of zircon products were investigated by the South African Nuclear Energy Corporation (Necsa). These were the synthesis of doped-zircon pigments from plasma dissociated zircon, and an upgrading process to convert an inferior grade of zircon into a superior opacifier for ceramic applications. A solid-state reaction process was used to produce doped-zircon pigments. The influence on the colour intensity of the pigments on a ceramic tile were compared for milled and un-milled plasma dissociated zircon (PDZ) material, prior to calcination. Pr-yellow and V-blue zircon pigments produced from PDZ with different degrees of dissociation, were also evaluated. The second zircon beneficiation process entails the upgrading of an inferior grade of zircon to a superior opacifier for ceramic applications. A calcining process in the presence of mineralizers was used to produce the product in a conventional muffle furnace. A pre-milled inferior grade zircon concentrate, with a relatively high iron and alumina content generally not suitable for high quality ceramic applications, was used in this study. The influence of the upgrading process on the opacifying properties of the zircon material was compared to that of commercially available prime grade zircon opacifier products currently being produced in South Africa. The influence of a calcining step in the presence of mineralizers with regard to the milling characteristics of the treated zircon material was also evaluated.

Jan 1, 2005

Two new inorganic-organic hybrid polymers, Al(OH)3-polyacrylamide (Al(OH)3-PAM) and Mg(OH)2-polyacrylamide (Mg(OH)2-PAM) were synthesized and successfully applied for the treatment of oil sand tailings. The results indicate that both Mg(OH)2-PAM and Al(OH)3-PAM were unaffected by the change in pH, and could be applied to oil sand tailings with varying sand-to-fine ratio (SFR). The optimum dosages for the Mg(OH)2-PAM and Al(OH)3-PAM were about 330 g/ton and 650 g/ton, respectively for SFR 3.75. The flocculated oil sand tailings dewater quickly producing 66-68% solids. The flocculated tailings produced similar filtration rate before and after shear. Mg(OH)2-PAM treated oil sand tailings produced twice the filtration rates (220 ml/min) compared with Al(OH)3-PAM. This study clearly indicates that Mg(OH)2-PAM and Al(OH)3-PAM is a viable solution while decreasing the mass-production of tailings and increasing the rate of water-recycle.

Jan 1, 2012

In this paper, uniaxial compression tests were conducted on intact rocks and broken rocks that were reinforced by grouting, and the effects of grouting on the strength of broken rocks were analyzed. The results show that after grouting reinforcement, the bearing capacity of broken rocks with different lithologies increased, and their uniaxial compressive strength recovered by approximately 6%–16%. The results indicated that the stronger the rock, the smaller the strength recovery of the consolidated body formed after grouting. At the same time, using borehole camera observation and deep overburden strata separations, the fracture development characteristics of surrounding rocks of the gob-side retained entry were analyzed and divided into different regions. On this basis, a guided grouting method was proposed; that is, shallow hole grouting was first used in the plastic zone of the broken surrounding rocks to form the isolation layer, and then deep grouting holes were arranged in the elastic-plastic zone of the transition zone to guide the slurry flow to the shallow unfilled zone. Therefore, the broken surrounding rocks were reinforced into an integrated body and selfbearing capacity improved.

Jul 28, 2020

By W. G. Pariseau

This contribution focuses on the role of stress analysis for mine planning and the selection of suitable computer programs for the task with special emphasis on coal mine pillars. In this regard, barrier pillars that defend a set of five main entries at the Crandall Canyon coal mine in central Utah were formed during extensive longwall mining north and south of these main entries. Numerical analysis for ground control guided the mine planning and permitting. Retreat mining of pillars led to disastrous events August 6 and 16, 2007, with the loss of nine lives. A most difficult lesson taught by the Crandall Canyon tragedy is the need for education in the selection and use of computer programs for pillar design. Much of this contribution is taken from a report prepared for the Mine Safety and Health Administration (Gates, et al, 2008). Details appear in Appendix Q of the report (Pariseau, 2008). The Crandall Canyon mine is about 16 miles west of Huntington, Utah, in the Wasatch Plateau coal field. Geology of the Wasatch Plateau is described by Doelling (1972) as gently dipping Cretaceous sandstones, mudstones, coal seams, and shales. Joint systems are present in strata above and below coal seams where cleat systems are present as described by Hucka (1991). Several major fault systems transect the field and form grabens with 450- 760 m of drop. One such structure is Joes Valley fault that crosses the Crandall Canyon mine. Mines in the Wasatch Plateau are generally developed from outcrops in steep canyon walls. Overburden increases rapidly as mining progresses into the plateau; mining depth varies with topography between 450 and 600 m in the region of interest. A stratigraphic column derived from a borehole into the mine is shown in Figure 1. There are 11 layers in the column.

Jan 1, 2011

Many investigators measured surface forces between hydrophobic macroscopic surfaces using atomic force microscope (AFM). Some investigators observed long-range attractions and attributed them to the presence of hydrophobic forces, while others suggested that they are artifacts of the nano-bubbles and cavities associated with the hydrophobic surfaces. Still others suggested that the long-range attractions are due to the electrostatic interactions between charged patches present on opposing surfaces and hence are unrelated to surface hydrophobicity. In the present work, we have measured long-range attractions between gold- (or silver-) coated surfaces hydrophobized in potassium ethyl xanthate (KEX) solutions at pH 9.2 under controlled potential conditions. The results of our AFM force measurements are consistent with those of the contact angle and voltammetry experiments, indicating that the long-range attractions are hydrophobic forces.

Jan 1, 2012

By Peter K. Mathison

The U. S. Department of Interior, Bureau of Mines (Bureau) is developing a hydrologic monitoring system for in situ leaching operations. A working prototype of this system was installed and tested at the Cyprus Casa Grande copper mine. Requirements specific to in situ leaching operations were identified by researchers. The system has been a useful tool for researchers and for mine personnel. Observations of the hydrologic monitoring system, including details of the development process, the design of the system, and the software developed at the Bureau have resulted in new ideas for an enhanced design of the system.

Jan 1, 1992

By Sean Masse

New Gold?s New Afton Mine, located 8 km (5 miles) west of Kamloops, British Columbia, is a 4.5-Mt/a (5-million stpy) block cave mine, making it the highest tonnage underground hard rock mine in Canada. The reserve is estimated at 52.5 Mt (55.9 million st) with grades of 0.65 g/t (0.02 oz/st) gold and 0.93 percent copper (2012). Commercial production was achieved in July 2012 and nameplate production was achieved ahead of schedule in September 2012, with the cave breaching to surface in 2013. The mill has a SAG and a ball mill with a froth flotation circuit.

Jan 1, 2014

By D. Bogh

Wound rotor motors are used in difficult mining applications where there is a need to start high inertia, hard starting loads while limiting inrush current They are recognized as robust and simple to control. This paper will cover the performance, specification, and important issues to be considered when applying medium voltage wound rotor motors in mining applications. Medium voltage grinding, crusher, and conveyor applications will be discussed. Specifically covered are motor efficiency, speed range, and rotor control. Crane motors often have wound rotor construction, but their load cycle and ratings are outside the scope of this paper.

Jan 1, 2011

By Yves St-Amour, Vince Luongo

This paper will discuss one of the largest construction projects the City of Portland has undertaken. This phase of the Willamette River Combined Sewer Overflow (CSO)project consists of approximately 18,500 ft of tunnel in soft ground, requiring the construction of six deep shafts and jet grout ground improvement. The purpose of the project is to reduce volume of combined sewerage overflows from the drainage areas on the west side of the Willamette River. Bencor-Petrifond-Pacchiosi Joint Venture was awarded a contract to design and construct six deep circular shafts, jet grout ground improvement for three bridges and jet grout ground improvement break-in/outs for some shafts. Of the six shafts the Pumping Station Shaft was the deepest and largest, requiring a permanent ground support system with a deep jet grout ground water cut-off to 335-ft deep. The joint venture used state of the art methods and equipment to achieve its objectives and build the structures through some very difficult alluvial soils to great depths next to the Willamette River. The paper will provide a general discussion of the shaft construction and jet grout ground improvement installed for this phase of the project. It will also discuss some of the technical challenges encountered while effectively managing risk and costs, resulting in a successful project completed in a timely manner.

Jan 1, 2005

By F. Schreiter

The Ore Mountains in Germany have a history of more than 850 years of underground mining activity. This has created a situation where thousands of old mine shafts and adits are due for rehabilitation. While no long-term stable rehabilitation was executed in previous centuries, those abandoned mine sites which date back to the uranium mining boom from 1945 to 1962 were rehabilitated immediately after mine closure according to state-of-the art technology. Over the years, however, it has become obvious that most of these sites are not long-term stable and thus it has become necessary to rehabilitate them a second time. Technical University Bergakademie Freiberg is carrying out a research project on the optimization of this process. 70 mine site rehabilitation projects, the technology and the materials used have been assessed. A technical guideline for future rehabilitation projects, based on the outcomes of this assessment, is under development with the goal to make it easier, faster and more economical to select and apply suitable designs and construction materials for dams, plugs and other rehabilitation structures in former uranium mines.

Feb 27, 2013

By C. A. Young, R. G. Robins, E. J. Dahlgren

The formation of copper thio-complexes in sulfide solutions has been recognized for many years and the measured solubilities of certain copper sulfide minerals attributed to these complexes. Attempts to model this system have proposed either copper(I) or copper(II) thio-complexes, and these have been incorporated into computer programs for generating stability diagrams for the copper-sulfur-water system in order to delineate the region where the reductive dissolution of copper sulfide minerals is likely. In this paper it is proposed that the dissolution of copper from both ore bodies and sulfide tailings can be explained by the formation of the cupro-thio-complexes under anaerobic conditions. Stability diagrams are presented to depict the region and extent of the solubility.

Jan 1, 2001

By James W. Stewart, A. C. Colvine

Introduction Precambrian shield terrains the world over are experiencing an unprecedented level of concerted exploration for lode gold deposits. Reasons for this include: • The increase in the price of gold (following 40 years at $1.13/g or $35 per oz) has transformed targets that were once unattractive into viable exploration propositions. • The relatively suppressed market for other metals produced from shields (base metals, nickel, iron, and uranium) has further focused exploration attention on gold. • The preeminence of gold production from rocks of early Precambrian age, as shown in Fig. 1. • The relatively high grade of gold in these mines (averaging about 10 Wt or 0.29 oz per st) permits profitable extraction even under depressed gold prices. A number of these mines have been in continuous operation for more than 50 years. • The recent discovery of the major Hemlo deposit, in well exposed rocks adjacent to the Trans Canada Highway, has had a world-wide impact. This demonstrates that a major new deposit can be found even in an accessible, well exposed area of a shield; gold mineralization is susceptible to rational exploration; and new target types for gold exploration exist. This paper reviews exploration activity for gold in shield terrains worldwide (Fig. 2), excluding Early Proterozoic paleoplacers of the Witwatersrand type. Emphasis is on the Archean, which is traditionally the most productive part of the Precambrian shields. There is also an emphasis on the Canadian shield (Fig. 3) because of its vast areal extent and exceptionally broad range of mineralization styles. Geological Approach A basic problem exists in gold exploration when compared to exploration for base metal massive sulfides that predominated during the 1960s and 1970s. Gold concentrations cannot usually be detected by airborne geophysical instruments. The majority of massive sulfide deposits were detected using airborne electromagnetic detectors and magnetometers. A full 75% of Canadian gold discoveries can be credited to surface prospecting. The percentage is even higher in other countries. This observation allows for great optimism for two reasons: • Large areas of shield terrain are obscured by either surficial deposits (glacial tills, clays, and desert sands) or deep surface weathering. This makes them inaccessible to prospectors. Logic dictates that such obscured areas should have the same potential for gold concentration as has exposed bedrock. • The Hemlo style of mineralization, a roughly tabular ore body where gold is associated with disseminated sulfides, is different from the traditional prospecting target. The gold is hosted by discrete quartz veins. While it is true that limited discoveries were made at Hemlo more than 30 years ago, and this style of mineralization is present elsewhere, recent

Jan 12, 1984

By K. Oraee

Rate of penetration of Tunnel Boring Machines (TBM) has a significant role in the planning, measurement of productivity and performance of any tunneling project. In this paper, the application of Adaptive Neuro Fuzzy Inference System (ANFIS) in prediction of TBM penetration rate is evaluated. For this purpose, a database including Rock Quality Designation (RQD), Uni-axial Compressive Strength (UCS) of the rock, the Distance between Planes of Weakness (DPW) in the rock mass, and empirical data regarding rate of penetration of TBM from several tunneling projects are collected. The Rate of Penetration is then estimated by using ANFIS. These results are then compared with measured TBM penetration rates (actual data). It is concluded that ANFIS can be applied successfully for such purpose and result in high accuracy for prediction for the rate of penetration of TBM. The method provided in this paper can assist the mining engineer to estimate the performance of tunneling accurately.

Jan 1, 2012