Search Documents

By Georgene Renner

At the beginning of the 1990s, Communism fell and signaled the end of the Cold War. The world rejoiced but also watched and waited to see how those countries would restructure themselves. The 1990 SME Annual Meeting was held at the Salt Palace Center in Salt Lake City, UT. The keynote session featured Alistair Frame, chairman of RTZ; Paul Queneau, professor of metallurgy at the University of Utah; and TS Ary, director of the U.S. Bureau of Mines. The SME Board of Directors voted to hire a Manager of Public Information and Education to be the GEM Program coordinator. This person was to collect and disseminate information that could be used by individual members and Local Sections to interface with government personnel and the general public.

Jan 1, 2007

One of the most important parameters in mine ventilation planning is the friction factor (K). Accurate values of friction factors are critical especially when carrying out mine ventilation simulations. No computer simulation of a mine ventilation network is meaningful if the airway resistances are not accurately estimated (when planning a new mine) or measured (for an existing mine). However, in the first case not many reliable values of friction factors exist in the international literature. This paper presents the results of a research project carried out in the province of Quebec where ventilation friction factors were measured in all underground metal mines. These friction factors are statistically analyzed and tabulated. A friction factor database was created that also includes the friction factors measured in the past by other people. This database can help the mine engineer to accurately estimate ventilation friction factors according to the specific conditions. This database offers several values of friction factors typical for hard rock mine conditions typical of modern underground metal mines.

Jan 1, 2009

By G. Miller

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixers. Recent experience with both large and small plants has shown that this is not the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers. Both of these lead to either reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Further, changes to the method of specification and selection of both primary and secondary mixers have been made to eliminate the onset of partial separation during operation. Observation of settler operation has shown that it is also a dynamic process, even under ‘steady state’ conditions. Four different transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze, and erratic and high entrainment levels in the discharges. A first approximation analysis has shown that there are significant pressure differentials within settlers and these change along the length and with phase separation rates. A technique to control the effects of these transients has been developed which allows plant performance to be improved beyond ‘standard’ expectations. The design and selection of the settler internals is described.

Jan 1, 2001

Employee safety and health is of paramount importance for SME and its members. Many SME members work daily in our Nation's mines or have a direct impact on others that work in the mines. SME supports the mission and purpose of the U.S. Mine Safety and Health Administration (MSHA), which is to prevent all injuries and disease from mining and to promote safe and healthful workplaces for the Nation's miners. SME supports the National Institute for Occupational Safety and Health and university research geared toward prevention of all occupational injuries and illnesses. SME maintains that laws and regulations governing the mining industry need to be based on sound scientific principles to ensure that workplace solutions can be readily implemented and that solutions to safety and health problems are fully realized.

Jan 1, 2011

By P. M. Prasad

Off-grade molybdenite concentrates, mainly derived from secondary sources as by-products of the processing of copper, uranium and tungsten ores, do not satisfy the purity requirements (percent MoS2) for the production of molybdenum bearing products. This investigation is a continuation of a successful effort to refine a low-grade molybdenite concentrate to prepare a high-grade MoS2 using a mixed acid (HF + HCl) leach procedure. Specifically, this investigation is concerned with an understanding of the separation chemistry underlying the removal of the oxide/silicate gangue and the base-metal sulfide associations present in the low-grade molybdenite by their selective dissolution in the two acids. Experiments were conducted on an off-grade concentrate containing 42.6% Mo. Results of the controlled dissolution tests indicate that both HCl and HF are suitable for the removal of the associated alumina and both work well for iron, nickel and copper. However, HF was found to be the most effective for dissolving silica/silicate and magnesia. An attempt was made to rank the leaching efficiencies of the acids used singly, sequentially or in a mixed mode. Scale-up (300 to 2,000 g) experiments were conducted to validate this approach. Excellent purification of the concentrate was possible by processing the off-grade concentrate with 10% HCl plus 15% HF at 363 K for 7.2 ks in open polypropylene reactors with internal stirring. These conditions leached practically all of the oxide and silicate gangue and 96% of the metallic impurities. Starting from the low-grade molybdenite concentrate (42.6% Mo; 71.1% MoS2) it was found feasible to obtain a refined product containing 97.8% MoS2, which is suitable for industrial use.

Jan 1, 2007

By J. Greg Sanchez

The New South Ferry Terminal in the New York City Transit system represents an important milestone for the city. This is the first station designed and built in the 21st century. The design of the fire safety system included relying on Computational Fluid Dynamics to analyze the dispersion of heat and smoke, and modelling of people egress to determine the egress requirements. The project also looked into how to protect the structure from the heat exposure in order to meet the fire rating requirements. This paper provides an overview of the fire safety design approach taken to design the new South Ferry Terminal station in lower Manhattan and looks into fire modelling, structural fire protection, and station evacuation.

Jan 1, 2008

By Phil Pennington, D. Jack Adams, G. Ward Wilson, Virginia T. McLemore, Luiza Aline F Gutierrez, Rodney Shields, Steven Lockwood, Samuel Tachie-Menson

Microorganisms are directly or indirectly involved in many chemical alterations and in the decomposition of minerals required for their growth. Microbial dissolution of sulfide minerals under acidic conditions can produce over 1,000 times more Acid Rock Drainage (ARD) than chemical action alone. Microbial actions can cause precipitation of minerals, adsorption or release of metals, and formation/destruction of organic-metallic complexes. Soluble minerals can serve as oxidizing substrates, electron donors/acceptors in redox reactions, and can be directly involved in cell metabolism. Microorganisms and microbial oxidation-reduction reactions and their contribution to mineral mobilization and stabilization will be discussed.

Jan 1, 2005

By W. Dziurzynski

The present article sets forward the results of field tests that made it possible to validate the mathematical model used in the VENTGRAPH ventilation engineer programmes. The case considered relates to the introduction of a new heading to the ventilation network of the mine. The utilisation of computer programmes in practice is justified by the necessity of ensuring expected performance and secure conditions in the network of mine headings, where - for example - plans are being made to utilise the transport dip-heading, taking into consideration fire and methane hazards. In the article we have presented the methodology of preparation of a database for computer programmes of the VENTGRAPH system, obtained on the basis of ventilation measurements. The next step consists in the execution of a design of the modified network and prediction, this on the basis of heading geometries, of parameters characterising the flow of air for the designed headings. Due to the fact that the heading was in the final stage of driving, following its introduction to normal operation and the stabilisation of flow values it was possible to retake ventilation measurements, which validated the results obtained through computer simulations. In order to execute measurements of the volume flow in the dip-heading, we employed a new wireless multipoint measurement system to determine the velocity field of air in the mine heading; the results are characterised by a high accuracy of measurement. As a part of fire prevention and incident management planning, a series of underground fire case studies for the a validated network flow model has been made. Results of simulations show the capabilities of the FIRE module of the mentioned software, including assessment of stability of flow directions and hints on counter and preventive measures for particular locations of fire.

Jan 1, 2009

By R. L. Wolfrom, R. Hogg, S. Chander

A gravimetric method for measuring rates of capillary rise in powders was explored. Methods to improve reproducibility and consistency of the results were investigated. In particular, the effects of particle size and packing uniformity were addressed. Studies of the wetting behavior of both spherical glass beads and irregularly shaped synthetic graphite particles by various organic liquids were carried out. Standardized procedures for bed preparation are described. The applicability of the Washburn equation for surface energy evaluation in such systems is discussed.

Jan 1, 2002

By D. M. Ziebarth

"During the mid to late 1960s, the underground potash industry in Saskatchewan was born. For the next four decades the industry operated at a steady pace, supporting a large part of the world demand, until 2008 when the potash market heightened. Operators were motivated to capitalize on this increased demand, new mines were proposed while existing mines were planning upgrades. Potash Corp. of Saskatchewan (PCS) was one of the major producers planning upgrades to its production facilities quickly, including modifying the existing headframe and shaft at the PCS Cory Site to accommodate a new 1.5-kt/h (1,650-stph) hoisting plant. Upon completion of the project, the innovative operations group continuously reviewed methods to increase production and reduce operating costs, allowing PCS to continue being competitive on the world market.BackgroundPotash production is a major Saskatchewan industry and has played a significant role in the economy for more than 40 years. Production commenced in 1962 when water problems were overcome at the International Minerals and Chemical (IMC) Mine near Esterhazy, Saskatchewan. A surge of development by other companies resulted in 12 companies opening 10 mines by 1970. In 1975, Potash Corp. of Saskatchewan was created by the government of Saskatchewan, and shortly thereafter purchased several mines in Saskatchewan, including the Cory Mine, near Saskatoon.Cory has been in operation since 1968 and is located 12 km (7.5 miles) west of Saskatoon in central Saskatchewan. The mine is located in the center of the world’s largest potash deposit, 1,000 m (3,300 ft) below surface.PCS has embarked on sizable capital expansions of more than CDN$7 billion.The $1.6-billion Cory expansion was expected to raise operational capability of the site to 2.7 Mt/a (3 million stpy), an increase of 1.9 Mt/a (2.1 million stpy). To achieve 2.7 Mt/a (3 million stpy) of finished product and considering the 22.6 percent average production recovery (Potash Corp, 2013), 12 Mt/a (13.2 million stpy) of ore must be hoisted to the surface for processing. To deliver this rate required upgrading of the hoisting plant to 1.5 kt/h (1,650 stph). To accomplish this ambitious challenge, creative thinking, careful planning and a cohesive team was needed to work together to ensure the schedule, budget and most importantly that the work was completed safely (Potash Corp., 2013)."

Apr 1, 2017

By A. Bobet

Design of a new underground laboratory is underway through the auspices of the United States National Science Foundation. The Deep Underground Science and Engineering Laboratory (DUSEL) is scoped to provide a diverse group of researchers with a dedicated underground facility capable of supporting a broad spectrum of fundamental and applied research at depth in the Earth?s crust. Key research partners in the endeavor are physicists, biologists, geoscientists and engineers. Engineers are not only designing the underground facilities, but are also actively involved in developing research initiatives. This paper will introduce the DUSEL engineering research program to the mining community, provide an overview of the site, geology, and laboratory facilities, and describe some key program initiatives. The particular technical challenges and opportunities afforded by the construction of DUSEL and the performance of the integrated science-engineering program will be discussed by reference to a subset of research initiatives that are currently under development: Cavern Design, CO2 Sequestration and Transparent Earth. These research initiatives target the development of new techniques that can support improved subsurface investigation, design and construction procedures. An increased use of the subsurface can actively contribute to the development of new, more sustainable solutions for use in mining and civil engineering practice.

Jan 1, 2011

By P. Sangurmath, C. Gundewar, M. Riyazulla, V. Vasudev, N. Shadaksharswami

Dharwar craton in the southern Indian shield, comprises the Neoarchaean foreland in the west and a relatively younger accretionary complex composed of granitoids and intervening gold-bearing volcano-sedimentary belts. The Hutti schist belt hosting a major gold producing mine is situated in the northern part of the eastern Dharwar craton. It is a horse-shoe shaped structure comprising predominantly of pillowed metabasalt of tholeiitic composition with minor amounts of clastic sediments and felsic volcanic rocks. The belt is intruded on all sides by circular to tabular bodies of granites and granodiorite. Important gold deposits are located at Hutti, Hira-Buddini and Uti villages. Felsic volcanics in the Hutti belt occur as tabular bodies of quartz porphyry and breccia. Two of the gold-bearing reefs in the Hutti mine, Viz., Middle and Strike reefs are intimately associated with tabular sub-vertical sheets of mylonitic quartz-feldspar porphyry intruding pillowed metrabasalt. In Uti mine area, the felsic volcanics occurs as a tabular body. At Hira-Buddini, the felsic volcanic occur as a irregularly shaped sheet in pillowed metabasalt. Mineralogical and geochemical studies suggest that the felsic volcanic rock in Hutti mine area is a rhyolite and at Uti and Hira-Buddhini it is of dacite composition. Scheelite occurs as veins, veinlets, stringers and blebs along fracture planes of felsic volcanics in the Hutti mine area, whereas at Uti and Hira-Buddini it is insignificant. On the basis of spatial association of metabasalt and felsic volcanics and on geochemical grounds, we interpret that the felsic volcanics might have originated by the partial melting of basalt. REE patterns of the granite, granodiorite and metabasalt of Hutti are similar to each other indicating that they could be co-magmatic. However, REE in the Hutti felsic rocks is significantly higher than in Uti and particularly Hira-Buddini mine areas. The two felsic volcanic samples drawn away from the mineralized zone from all the three mine areas were analyzed for tungsten. In Hutti one sample assayed 0.15% and another 0.062%. At Uti, in one sample it assayed 0.056% and another less than 1 ppm, whereas at Hira-Buddini, it is less than 1 ppm in both the samples. The spatially associated basalt analyzed 23 to 235 ppm tungsten, whereas granites and granodiorites have very low (<1 ppm) tungsten. Therefore, the source of tungsten in the felsic volcanics of Hutti area could be traced to metabasalt. The absence of significant amount of tungsten in the felsic volcanic of Hira-Buddini could be attributed to the lack of REE enrichment compared to REE in Hutti and Uti felsic volcanics.

Jan 1, 2007

By Wolfgang Guetter, Wolfgang Weber

The upgrading project for two hydropower plants in Slovenia, Europe, requires two new pressure tunnels: Plave II (5.9 km Flysch) and Doblar II (3.6 km Limestone). It is the worldwide largest application of the Double-Shield TBM technology combined with an extremely thin-walled monoshell honeycomb lining system. The first drive has been completed by end of June 2000 achieving best performances of 50m/d and almost 1,100m/mth. In September 2000 the TBM started the second tunnel without any required adjustments due to geological or other reasons. Another 52m/d have been bored already within one production day of two 8 h shifts achieving a maximum penetration rate of more than 6m/h. The completion of the Doblar drive can be expected by February 2001.

Jan 1, 2001

By F. Bruey

The Factorial Model Experimenters are often interested in systems that are multi-factorial. A multi-factorial system is one whose output is believed or known to be dependent on the particular settings of several inputs, or factors. We can think of these factors as defining a space, with each point in this space corresponding to a particular set of factor settings. Experimenting can be thought of as exploring this space - finding out how the response of the system changes as factor settings are changed. There are several challenges in this exploration, among which are deciding what region to explore, designing an experiment that explores it most effectively, and describing the results of the exploration. This paper deals principally with the last of these; it shows how the factorial model can be used to describe how the response of the system changes as factor settings are changed. A strength of the factorial model is that it treats the factors as causes of change in the system&apos;s response and focuses on relations among these causes. In particular, the factorial model focuses on whether causes act independently on the system (in a sense to be explained below), or whether they interact. This is important because the experimenter generally seeks to control the system, and because control based on causes that act independently of other causes is relatively simple, whereas control based on causes that interact is more challenging. Also, mapping the space - finding out how the response of the system changes as factor settings are changed - will require less work if, during the exploration, it can be determined which of the causes act independently. For the sake of example, let us assume that the space we are exploring is three-dimensional, and that we have already defined, for each of the three factors, the range of interest. Let us consider all the ways in which the response of the system might depend on the settings of these three factors. In the simplest case, the response in this region does not depend on any of the factors. The response is constant throughout the space, at say, 80 units.

Jan 1, 2007

By K. Hanson

When done properly, benchmarking is an extremely effective tool for assessing ones performance, finding areas for improvement, and identifying strengths. However, when done improperly it can be an exercise in futility and result in incorrect observations and conclusions. A primary pitfall of benchmarking is collecting too much unreliable information. Surprisingly, the evolution of data storage and the ease of data collection are not helping with better data collection. Instead, it is just allowing one to collect more information, while at the same time inundating one with too much data. Additionally, the process of data collection can be tedious and is often times delegated to the least experienced individual resulting in unreliable and incorrect data collection and entry. Another primary pitfall of benchmarking is metrics that are cost based or poorly designed. Cost based metrics typically involve comparing unit mining costs ($/tonne). Between mines, unit mining costs are not very well correlated and have become further complicated by significant regional cost variations and mining inflation in the last years. Likewise, poorly designed metrics lead to poor benchmarking results. Examples of poorly defined metrics include: metrics that rely on information that is difficult to collect, metrics that are poorly defined, metrics which are too site focused, and metrics that measure low consequence practices.

Jan 1, 2011

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents preliminary test results obtained with a 0.38 kg/s (3000 lb-hr) beta prototype MagMill™. In processing Upper Freeport coal the beta prototype recovered 82% of the weight of the feed and 91% of the heat content while reducing the potential emissions of sulfur, kgSO2/GJ(lbSO2/MBtu), by 61%. Pyritic sulfur in the MagMill™ product was reduced by 78% compared to that in the feed. For all runs, the mill product was controlled between 70 to 80% finer than 74 µ particle size. Recoveries of mercury, arsenic, and selenium ranged from 35 to 45% of that in the feed. Power draw was reduced by 26% and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2000

By S. Janisko

Studies have linked long-term inhalation of diesel exhaust with adverse health effects such as cardiovascular disease, cardiopulmonary disease, and lung cancer. Diesel exhaust levels in underground mines can approach 100 times the environmental level and are therefore monitored closely in the mining industry. Elemental carbon (EC) (a product of diesel combustion commonly referred to as ?soot?) has proven to be a good indicator of diesel exhaust levels. The current procedure for measuring EC levels involves taking personal samples from a mine worker?s breathing zone and/or stationary samples in various parts of the mine and subsequently sending these samples to a lab for analysis by NIOSH 5040 method. Unfortunately, the whole process can take up to several weeks to complete. To address the problem of waiting weeks for results, NIOSH?s Pittsburgh Research Laboratory is developing a portable device for measuring levels of elemental carbon. This optical device takes a continuous sample of air in the surrounding environment and measures the absorbance of light passing through a filter that collects diesel exhaust particulates within the instrument. This technology can provide a near real time measurement of EC with accuracy within 10% error. The ability to take near real time measurements, combined with the instrument?s portability (currently small enough to be worn on a miner?s belt), makes this device extremely useful in the mining industry.

Jan 1, 2009

By R. K. McLimans, C. Knudsen, S. Bernstein, D. Frei

Computer Controlled Scanning Electron Microscopy (CCSEM) is used to analyze indivdual mineral fractions in heavy mineral sands. CCSEM is a fully automated particle analysis technique for the determination of physical and chemical properties of a large number of individual particles. CCSEM enables the precise and accurate determination of the modal abundances of individual mineral fractions (e.g. ilmenite, rutile, zircon, or garnet), their average chemical composition (and compositional variation), as well as their physical properties such as size (e.g. diameter and perimeter length) and shape (aspect ratio and circularity). A unique sample preparation procedure is used to produce representative polished sections from cylinders of raw sand samples such that thousands of grains are present in a polished cross section, but grains are not touching. The combination of this sample preparation technique with CCSEM enables the fully automated analysis of individual grains without the application of de-agglomeration or erosion steps to separate touching particles. Hence, CCSEM yields information representative of the entire area of analyzed grains without systematic bias due to neglect of rim areas by de-agglomeration or erosion steps. Therefore, the resulting data are determined with high accuracy, precision and statistical validity. Because the sample preparation is relatively straightforward, using raw sand samples, and all chemical and physical properties are determined in one analytical session per sample, CCSEM is a powerful cost and time efficient tool for characterizing chemical and physical properties of minerals in heavy mineral sand deposits.

Jan 1, 2005

By T. Hudaverdi

Several studies have been conducted on blastability and prediction of fragmentation. The term blastability is used to refer the susceptibility of the rock to blasting and is closely related to fragmentation. Parameters that determine fragmentation by blasting may be divided into two groups. The first group consists of blasting design parameters. The blast design parameters are controllable parameters and determined by the explosive engineers. The burden, spacing between holes, bench height, drillhole diameter, stemming height and explosive density are all design parameters. The second group consists of rock mass parameters that are referred to as uncontrollable parameters. The uncontrollable parameters are physical and mechanical properties of rock and rock mass structure. The strength, modulus of elasticity, density of rock, number of joint sets, joint orientation and joint spacing are among uncontrollable parameters. The rock mass parameters and blast design parameters should be considered together to explain fragmentation process. In this study, a blast database was accumulated to use for multivariate analysis. The blast database contains the blasts performed near Istanbul region quarries and the blasts that were preformed in various mines in the world by the blasting researchers. The cluster analysis was used to separate the blast data into different similarity groups. Group memberships were analyzed and checked by the discriminant analysis. Then, the multivariate regression analysis was used to develop a prediction equation for blast fragmentation for each group. Finally, a validation of the suggested models was performed for various mines. The model comprises blast design parameters, mechanical properties of rock and rock mass structure.

Jan 1, 2011

By G. Krogman, C. Walla, B. Wood

The Gebo Mining District (District) is located in the Bighorn Basin of Wyoming. Commercial underground coal mining began in 1906 with the arrival of the railroad in Thermopolis, which is located approximately 11 miles to the south. Mining in the District ceased by the early 1970’s. In Fall of 1999, Lidstone and Associates, Inc. (LA) and their subcontractors were retained by the Wyoming Abandoned Mine Land Division (WyAML) to perform an inventory of over 500 abandoned mine sites across Wyoming. During the summer of 2000 field inventory, a 30-foot deep headcut (Figure 1) and sink-hole were noted in the West Fork of Sand Draw (WFSD), immediately west of the Town of Gebo. The headcut and sink-hole were located at the culvert outfall associated with a stream crossing of a relatively well traveled county road. Upon further investigation, it appeared that underground mine workings had been exposed at this location. This resulted in a condition whereby water would be conveyed directly into the mine workings during a runoff event. The exposed mine workings as well as stream capture created a very hazardous condition. The WyAML implemented mitigation measures in the summer of 2000 by constructing a temporary stream crossing upstream of the existing failed crossing. To address this hazardous situation as well as a number of other hazards identified in the District during the field inventory, the WyAML retained PHC Reclamation, Inc. (PHC). PHC was directed to perform a field investigation and develop a Reclamation Plan to address all existing abandoned mine hazards in the District. Federal, state, and private parties own lands within the District. Hazards identified during the investigation included an underground mine fire, open adits, open shafts, subsidence, drainage problems, and coal slack. A Report of Investigation (ROI) was submitted to various regulatory agencies that documented the existing conditions and conceptual reclamation plans to remediate the hazardous conditions. After review of the ROI by the US Department of Interior - Bureau of Land Management (BLM) an on-site meeting was conducted. BLM Cultural Resource personnel declined to approve a District reclamation project until a historical overview of the entire District was prepared. Due to the hazardous situation associated with the WFSD stream crossing, Hot Springs County Road and Bridge Department convinced various state and federal regulatory agencies to allow reclamation of the stream crossing to occur. A decision was made to allow reclamation on privately owned lands within the WFSD drainage. This decision limited the amount of channel that could be subjected to reclamation upstream of the crossing to privately owned lands. PHC contracted LA to perform a geologic, geomorphic, hydrologic, and hydraulic investigation of the drainage to assist in the development of a WFSD reclamation plan. LA’s investigation consisted of four parts: Delineate the extent of mine workings in the area; Identify all drainage structures that required mitigation; Survey a series of channel cross-sections and a longitudinal profile of the impacted channel; and, Develop basin hydrology to assist in the design of a stable reclaimed stream channel.

Jan 1, 2006