Search Documents

By C. G. Anderson

Throughout the world, there are many orebodies or materials which have significant value but also contain arsenic, antimony, and mercury. As regulations on the transport, exposure, disposition and emission of these elements have become more stringent; it has become increasingly more difficult to derive the values from the resources. This paper outlines the fundamentals of alkaline sulfide hydrometallurgy and its successful application to arsenic, antimony and mercury bearing ores, concentrates, by-products, and other materials.

Jan 1, 2008

By J. Lux, B. Clermont

Magotteaux, with the co-operation of Anglo Platinum, has erected a fully instrumented pilot plant at Frank concentrator, which is being used to study the influence of a variety of grinding parameters. This paper will discuss only the influence of mill speed and pulp density on secondary stage grinding. A Ø0.82 x1 m open circuit mill was used with reclaimed Merensky tailings as feed. The conclusions apply to this pilot plant but further investigation needs to be done to verify whether the same trends will be applicable to a large industrial-scale mill.

Jan 1, 2004

By J. W. Latilla, J. J. van Wijk

A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. Une cassure de taille en avant des unités de soutènement s’est produise sur la veine numéro 4 dans le puits numéro 3 (Matla 3) de la mine Matla Coal en avril et mai 2002. Les conditions d’extraction étaient extrêmement difficiles sur une distance d’environ 150 m dans la voie de tête et, en moindre mesure, sur le front de taille lui-même. L’étude présente analyse les raison majeures pour les conditions de grandes contraintes qui ont conduit à la cassure de taille, à savoir l’existence d’un mur de dolérite de >20m proche de la surface et l’effet d’arrêter la longue taille sur la veine 5 superposée. Les difficultés rencontrées pendant la cassure de taille sont rapportées, y compris les effondrements de piliers et toit dans la voie de tête, les aires de grandes contraintes en avant du front de taille causant des problèmes de stabilité pour le toit et les parois latérales, l’injection de roches cassées dans la taille en voie de tête, les cassures secondaires à mi-taille, et la disponibilité d’unités de soutènement critiques. Interventions minières réussies et leçons apprises furent : un angle de remblai de 14.6° était plus réaliste que celui de 20 à 25° utilisé auparavant pour prédire la conduite du mur de dolérite dans cet endroit ; tir à deux temps du mur a réduit considérablement les contraintes sur la taille et la voie de tête, ce qui a permis un travail de support complémentaire ; des types variés de support de piliers furent analysés et évalués ; la nécessité d’avoir toujours une trousse de première urgence disponible fut reconnue ; et finalement une stratégie pour les panneaux en dessous du mur fut

Jan 1, 2003

This paper describes the integration of the mineral resource management philosophy within strategic long term planning at Anglo Platinum Limited. Consideration is given to the philosophy, processes, techniques and supporting systems.

Jan 1, 2007

By S. Stone

Because of problems encountered with conventional timber supports, a system of concrete sausageshaped support pillars was tested. The pillars are 3 m long, 0,6 m wide, and between 70 and 80 cm high (the height of the stoping width). They consist of bags filled with a grout of cement (slagment and sand in the ratio of I :2, and are installed in a staggered pattern 6 m apart on dip and 2 m apart on strike. These support packs have proved successful, and, although they cost more than the timber supports formerly used (R4,63 per cent are supported as against R2,26 for the conventional timber pack), their use is felt to be justified when account is taken of the costs of lost production and low productivity due to the bad hangingwall conditions that occurred with the conventional system.

Jan 1, 1978

By N. Kinoshita, Y. Inada

The authors have proposed and discussed storage of low temperature materials such as LNG, LPG and frozen food in rock caverns. In this case, as the rock mass around the caverns will receive effects of low temperature, it is necessary to consider the thermal behavior and the stability of caverns. In this study, strength and deformation characteristics obtained by the uniaxial tension test and the compression test at low temperatures were discussed. Using the results, temperature and stress distribution around caverns when LNG was stored, were analyzed. Then thermal behavior of the rock mass around caverns was discussed. Die Autoren haben Lagerung von Niedertemperatur-Materialien wie LNG, LPG und tiefgefrorenen Nahrungsmitteln in Felskavernen vorgeschlagen und diskutiert. Da in diesem Fall die Felsmasse um die Kavernen den Effekten der niedrigen Temperatur ausgesetzt ist, ist es erforderlich, das Thermalverhalten und die Stabilität der Kavernen zu berücksichtigen. In dieser Untersuchung wurden Stärke-und Deformationseigenschaften, die durch ein-axialen Spannungstest und Kompressionstest bei niedrigen Temperaturen erhalten wurden, diskutiert. Mit diesen Ergebnissen wurden Temperatur- und Stressverteilung um die Kavernen bei Lagerung von LNG analysiert. Dann wurde das Thermalverhalten der Felsmasse in der Umgebung der Kavernen diskutiert. Les auteurs proposent et discutent l'entreposage de matériaux à basse température, tels que le GNL, le GPL et des aliments congelés, dans des cavités rocheuses. Comme, dans ce cas, la masse rocheuse entourant la cavité subit les effets des basses températures, il est nécesaire d'étudier le comportement thermique et la stabilité des cavités. Dans cette étude, les auteurs discutent des caractéristiques de résistance et de déformation, obtenues par essai de tension uniaxial et essai de compression à basse température. En se servant des résultats, ils analysent la répartition de la température et des pressions autour des cavités, lors du stockage de GNL. Ils discutent ensuite le comportement thermique de la masse rocheuse autour des cavités.

Jan 1, 2003

Professor N. S. Budavari holds a Dip!. Min. Eng. from the Technical University of Sopr on, Hungary, and a Ph.D. degree from the University of Newcastle-upon-Tyne, U.K. Mr J. J. Geldenhuys, Pr. Eng., is Divisional Manager Mining of Anglovaal Limited, being in charge of Prieska Copper Mines (Pty) Limited, Loraine Gold Mines, Limited, and Village Main Reef Gold Mining Company Limited.

Jan 1, 1983

By A. J. Jager, D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2004

Mr D. Twigg graduated in Metallurgy at the Sheffield Polytechnic, and later obtained a Master of Science degree at the University of Bradford. Mr I.D. Matthews matriculated at Roosevelt High School and joined the No. 1 Parachute Battalion in 1968. He worked in Zimbabwe for 31 years in geological prospecting, civil engineering, and open-pit mining.

Jan 1, 1985

By C. A. F. Sweet

The inter-relationship between these parties and the effect on the outcome of the project is often grossly underestimated. There are numerous success stories where the parties have worked as complementary teams aiming at the best outcome for the client company and achieving significant success. While there are a good number of occurrences where either the roles of the parties were unclear or perceived to be different from what others in the team believed or required them to be and the results were less than desired. This usually resulted in ongoing conflict, incorrect focus, working to different agendas and the result being a less than optimum result to Client Company. Mining, by its very nature of exploring where you cannot see, be it a shaft being sunk, tunnel being developed or other excavation that needs to be made, requires a very special working relationship between the parties. To understand this, and it applies equally well to mine and plant construction and other multiple function projects, one needs to start by describing the relationship of the parties. Often people believe that because they manage ongoing complex operations and large numbers of people that they can manage projects and as such the participants will ?fall into line.? At the outset it needs to be stressed that ?Project Management? is a specific type of management and needs to be understood as such. There are enough Colleges and Universities that teach project management, not only as a subject but also as a Master Degree. As you start up your project the relationship you establish between the client, project team (C.P.T) and the Engineering, Procurement, Construction and Management team (EPCM) will largely determine how successful your project will be. It is essential that from the outset a spirit of co-operation, support and respect be nurtured, and that it be actively carried through the project life cycle. There are several methods to facilitate this including team building exercises right at the start. This time and money will be well spent and recouped many times over during the project life cycle.

Jan 1, 2005

By R. Strydom, J. H. Selby, J. Slabbert, W. Enslin

Zircon is a naturally occurring silicate of zirconium, which is used in large quantities (~1 million tonnes per annum) for its refractory properties and its extreme chemical inertness. All zircons contain uranium and thorium bound into the crystal lattice, generally at levels up to 500 ppm of uranium plus thorium. This paper focuses on one aspect of the zircon industry—the ability to safely transport large quantities of zircon sand. Currently zircon is not classified as a radioactive material for transport purposes. However, this is because of a factor used in the exemption clauses of the IAEA code on safe transport of radioactive materials. The objective of this study was to determine the validity of this factor, and was submitted as part of an IAEA Coordinated Research Project (CRP). The study is based primarily on measured rather than modelled data and covers the transport of large quantities of zircon from producers in South Africa to customers in Europe. Both occupational exposure of workers and exposure of members of the public have been considered. The transport routes studied cover rail, road, ocean-going ship and inland barge transport of unpackaged bulk products. The study showed that the most exposed member of the public would receive 10µSv/annum,while the most exposed worker would receive 144µSv/annum of exposure. It is concluded that these levels are well below all regulatory limits for such activities involving naturally occurring materials. The study also showed that normal operational exposures are higher than those in accident scenarios, a feature which does not occur with higher activity materials. It is further concluded that the study validates the use of the factor of 10 in TS-R-1, as applied to zircon sand. Additionally it is also concluded that the exemption currently applied to the transportation of bulk zircon sand is valid.

Jan 1, 2003

By S. K. Gilman, V. E. Hugo

A common problem encountered in the mineral sands industry is that the mineralogical measurements used in defining the resource are not readily converted to metallurgical recoveries, which are used to predict the quantity of the final products. The problem stems from the different objectives of the exploration and metallurgical assessment programmes, and is often compounded by the use of different laboratory techniques and mineral definitions. Common mistakes include the misapplication of routine analysis, incorrect interpretation of mineral recovery, the confusion of mineral recovery with product yield and inconsistent definition of the same mineral. Experience has shown that unless these potential mistakes are identified, the measurement techniques used during exploration and metallurgical assessment are not compatible, often resulting in large errors in the prediction of mineral production. There are no easy solutions to the problem, as there is no universal assay technique which can cost effectively characterize all the mineral sands resources. The recommended course of action will therefore require several iterations to optimize the assay technique to suit the resource. Fundamental to the success of the measurement technique is the understanding of the mineralogy, its behaviour during mineral processing and the quality requirements for the final products.

Jan 1, 2003

By J. A. Taylor, R. J. Fowell

Abstract: The amount of published literature pertaining to the field of rock mechanics has increased markedly in recent years. Whilst computer applications aid our understanding of the mechanisms of pillar instability, the applications do not take into account the effect of time; thus the determined pillar factor of safety has limited meaning. A more realistic approach would be to consider pillar stability in terms of time to failure. However such an approach would require a reasonable estimate of the in-situ pillar mass strength and a validated methodology linking the time to failure with in-situ pillar mass strength and the geometric layout of the working. Résumé: Le volume de bibliographie au sujet de la mécanique des roches a augmenté considérablement ces derniêres années. Alors que des modeles informatiques aident a la compréhension des mécanismes d'instabilité de pilliers, ces modèles ne prennent pas en compte les effets du temps; ainsi, la determination du coefficient de surete du pillier a un sens limité. Une approche plus réaliste devrait considérer la stabilité du pillier en fonction du temps de défaillance. Cependant une telle approche exigerait une estimation raisonnable de la resistance du massif rocheux du pillier ainsi qu'une méthodologie qui lie le temps de défaillance avec la résistance in-situ du massif rocheux du pillier et la géometrie de l'excavation souterraine. Zusammenfassung: Die Anzahl der Veröffentlichungen auf dem Gebiet der Felsmechanik ist in jüngster Zeit sehr gestiegen. Computerprogramme sind wertvoll um den Mechanismus der Pfeilerunbeständigkeit zu verstehen, aber sie vernachlässigen den Zeiteffekt. Daher haben die errechneten Sicherheitsfaktoren der Pfeiler nur begrenzte Bedeutung. Eine realistischere Bewertung wäre, die Stabilität der Pfeiler auf Grund der Zeit bis zum Verfall zu beurteilen. So ein Verfahren würde eine Schätzung der in-situ Gebirgsfestigkeit und eine validierte Methologie, die die Zeit zum Verfall in Abhängigkeit der in-situ Pfeilerfestigkeit und der geometrischen Auslage der Grube zusammenbringt, brauchen.

Jan 1, 2003

Most processing plants use automatic samplers to extract ore aliquots along a producing shift. These aliquots are combined into a sample normally sent to lab analysis. The sampler used in the extraction of an aliquot from a continuous flow of ore, i.e. a belt conveyor is required to be both precise and accurate. Surprisingly, not all commercial automatic samplers exhibit these two mandatory properties. Consequently, it is recommended the development of a procedure able to check sample assays reproducibility obtained using a given sampling protocol. This paper uses the Gy’s sampling theory to evaluate coal quality control practices at a washing plant using an automatic sampler extracting coal increments from the ROM feeding belt conveyor. Gy’s theory provides the means to establish the precision limits for a given sampling protocol. Various ore properties are required to be determined in combination with sample mass and mass of the lot sampled. All this information leads to the definition of the precision limit. The precision limit obtained was checked via an experiment mimicking what happens in situations where both miner and consumer use the same and appropriate sampling practices. The experiment demonstrates that sampling theory precision limits were valid if unbiased samplers are used by both parties, i.e. miner and consumer. Keywords: sampling, quality control, coal

Jan 1, 2003

By M. Yavuz

Equipment selection in mining operations is an important issue, and also difficult to solve in multiple criteria environments. The paper in question has aimed to develop computer software for solving equipment selection problems in mining. In their paper, Basçetin et al. have analysed two case study problems related to open pit and underground mining method selection. By using Yager?s method1, the authors have selected 18 different criteria in the first case study and 21 criteria in the second case study. However, as emphasized by Ozdemir2, in pair wise comparison matrices the appropriate number of criteria should be seven as the maximum, from the point view of validation, consistency and redundancy. In cases where there are more than seven criteria to be handled, it is suggested that the criteria should be clustered and then the maximum number of clusters and subcriteria of every cluster should be limited to seven4.

Jan 1, 2007

By A. R. Leach

Anomalous mining conditions can be described where the level of hazard is increased relative to normal conditions within a mining area. Normal conditions would be those defined as a Ground Control District in a mine’s code of practice, and for which mine standard support layouts are generally developed. It has been found that up to 80% of fall of ground accidents occur where anomalous mining conditions exists, typically in the vicinity of geological weaknesses. These areas require specific attention to ensure they are readily anticipated and identified and that appropriate strategies are used to reduce the hazards associated with them. As part of SIMRAC project GAP 607 checklists to aid identification and best practice mining methods were identified for a range of geotechnically anomalous conditions.

Jan 1, 2003

The Institute has set important objectives for 1988 to make the Institute still more purposeful. Precious metals The Second International Symposium on Mining, Extraction, and Processing of Precious Metals will be held in Las Vegas, Nevada, USA, during the 118th TMSAIME Annual Meeting in March 1989. The First International Symposium on Precious Metals.

Jan 1, 1987

By J. H. Zietsman, M. W. Erwee, Q. G. Reynolds

Pyrometallurgical furnaces, essential for metal extraction, operate at temperatures exceeding 1600°C and represent complex multiphase systems that challenge direct industrial research. Multiphysics models play a key role in shedding light on their intricate behaviours, supporting the refinement of design and operational strategies. Integral to the operation are the tap-holes, which facilitate the removal of molten products and are routinely opened by lancing, a process comparable to the use of a cutting torch, where high temperatures result from oxygen reacting with an iron lance. When the lance pierces the clay, oxygen gas enters the furnace, which could influence the behaviour of the molten material inside. In this work, a multiphase fluid flow model was used to investigate bulk flow dynamics, with a focus on the effects of the lancing process on the inside of the furnace, immediately behind the tap-hole. Incompressible and compressible multiphase fluid solvers were used and compared with respect their performance – the intention was to assess whether using a compressible solver would yield a different solution to the incompressible one. It was concluded that there are negligible disparities in bulk fluid flow behaviour between the solvers for the case studies examined, indicating that solver selection might be less consequential for certain aspects of oxygen lancing.

Apr 16, 2024

By R. P. H. Willis, A. G. du Plessis, R. B. Wilson

This paper reviews issues to be considered in choosing primary access and transportation options for platinum and other mines. It proposes appropriate criteria and a methodology for deciding on the optimum primary access option for any particular orebody. Also included are generic parameters that can be used to facilitate the process of choosing the optimal access option.

Jan 1, 2004

By H. Griesel

The overall supply of platinum is forecast to rise more than the demand, and market deficit will narrow somewhat, but is still substantial at about 480 000 ounces. Because of this deficit, the price of platinum is expected to remain high, not taking into account the impetus from funds and speculators. With this strong demand for platinum and the high price, platinum producers still need to initiate projects to not only sustain current production, but also expand output into the high demand. However, the rise in the platinum price does not entirely offset the drop in revenue due to the strong rand. Consequently, in the current economic environment, executives and managers are under extreme pressure to initiate only the highest yielding projects and implementing them successfully. During the initiation phase of a project, the cost of changing concepts is the least, and strategic project decisions are the most important. It is during this phase that the most value can be added to a project, therefore requiring inputs from highly skilled, creative and experienced people. This paper will discuss thought processes and paradigms during the initiation of projects that will assist project owners in the selection and initiation of successful and profitable projects. The project initiation process will also be discussed outlining selection models, risk analyses and funding considerations.

Jan 1, 2004