Search Documents

By Mark R. Stephenson

Everyone knows that mining is a noisy job, but did you know that you are nine times more likely to lose your hearing than someone who works in a quieter job? If unprotected from noise on the job, by age 50, you will probably need hearing aids. Obviously, the best solution is to engineer out the noise, but that isn?t always im­mediately possible. Until mines are quieter, one way you can help save your vital sense of hearing is to use hearing protectors whenever the noise around you is hazardous. Even if you already have some hearing loss, you can use hearing protectors to prevent your hearing from getting worse. When loud noise is present, proper use of hearing protectors will help miners pre-vent most or all noise-induced hearing loss.

Jan 1, 1998

By S. J. Schatzel, J. Cervik, A. A. Campoli

The cross-measure borehole technique is being studied by the Bureau of Mines as an alternative to the use of surface gob boreholes as a means of controlling methane in gobs during longwall mining. Small-diameter holes are drilled from underground locations into strata overlying the mined coalbed. When the roof strata are fractured by the mining opera- tion, a partial vacuum applied to the boreholes draws the methane out of the fractured strata and prevents it from entering the mine ventilation system. Tests in the Upper Kittanning Coalbed showed that 50 pct of the methane produced by the longwall mining operation was captured by the cross-measure boreholes. Borehole inclination and penetration into the gob are two important borehole parameters that affect the performance of the cross-measure borehole system.

Jan 1, 1983

Reduce costs of recontouring surface mined land by improving bulldozer blades. Approach A specialized 48-foot-wide bulldozer blade set at an angle, a 13-foot bulldozer blade with swept-forward end sections, and a 24-foot grading bar are used in conjunction with conventional bulldozers to reduce the cost of recontouring surface mined land. How They Work The angle blade is used to do the initial and intermediate leveling of long spoil banks. It is mounted at an angle on two 410-horsepower crawler tractors in a side-by-side offset configuration, but requires only one operator since both tractors are controlled by a single set of controls. The angle blade usually begins its cycle at one end of the spoil bank where the operator fills the blade and moves forward, continuously cutting and casting the material to the repose slope. At the opposite end of the spall bank, the angle blade turns around and begins cut-ting and casting material to the opposite repose slope. This action continues until adjacent banks meet or the lateral distance from the center line of the spoil bank to the repose slope exceeds approximately 40 to 50 feet. At this distance, the sidecasting angle blade is no longer effective, and conventional bulldozers are used to do the final land shaping.

Jan 1, 1981

By Thomas M. Barczak, Christopher Mark

Roof supports can only be understood in conjunction with the rock structure that they support. The strength of the rock depends on geology, and the loads are applied primarily by the in situ and mining-induced stresses. Other factors, such as wider spans and retreat or multiple-seam mining, can also reduce the stability of mine openings. Roof supports are used to help stabilize these openings, but their performance characteristics must be properly matched to the loading environment and ground behavior if they are to succeed. Roof supports include both intrinsic supports, such as roof bolts, and standing supports. The key characteristics of any support include its maximum load-carrying capacity, stiffness, and residual strength. Other important factors are the timing of installation, the stability of the support as it is loaded, and the capability of the support system to provide skin control. This paper explains in practical terms how supports work and the important factors in ensuring that a good support design and application strategy are developed.

Jan 10, 2000

By D. E. Anders

Saturated hydrocarbons from 60 selected samples of a 2,300-foot Green River Formation oil-shale core (Piceance Creek Basin, Colo.) were analyzed by gas-liquid chromatography techniques. Emphasis was placed upon the distribution of normal alkanes and 15 key-branched and cyclic alkanes. The latter compounds consisted of the C15, C16, C18, C19, and C20 chain isoprenoids, the 5-a and 5-ß C27, C28, and C29 steranes, three C30 pentacyclic triterpanes, and perhydro-ß-carotene. The results showed definite evidence of maturation of both the n-alkanes and the branched and cyclic alkanes; however, most if not all of the changes were limited to the indigenous soluble extract and were not the result of additional soluble extract generation from the insoluble kerogen. Source material and environmental variations were important factors in some of the observed differences in the branched plus cyclic alkane compositions.

Jan 1, 1973

By R. R. Backer

The Bureau of Mines, in cooperation with Washington Irrigation and Development Co. (WIDCO), evaluated the dewatering of fine coal-refuse slurry using chemicals and various types and combinations of drains in natural earth impoundments. About 40 lb of lime and 2 lb of polymer per ton of dry solids were mixed with the underflow from the preparation-plant thickener. Clear, free water was immediately liberated from the slurry. The percent solids by weight of the slurry increased from about 17 to 30 immediately, and after 5 days increased to 45 wt-pct. This indicates a threefold reduction in total volume after 5 days from 172 cu ft/ton solids originally to 56 cu ft/ton solids.

Jan 1, 1981

To precondition a stope in advance of mining and thus reduce or prevent rock bursts. Approach Drill deep holes from a mine opening in a radial pattern in the vein and load and blast to fracture, the rock prior to production mining How It Works Preconditioning of a sphalerite galena vein in a hard gangue of quartz and quartzite creates a zone of softer rock that fails by displacement rather than violently as an elastic-battle mass. However, the entire area must he analyzed carefully so that the stress transfer does not cause problems in other workings of the mine A typical drill hole pattern and explosive loading is shown in the sketch. Hole diameter is about 4 inches and a down-the-hole, type drill is used. Drilling speed in hard quartzite is about 12 inches per minute High pressure compressed air (250 psi) is used to run the drill. An overhand cut-and-fill stoping area on the 7700 level of Hecla Mining Company's Star Mine in Burke, Idaho was preconditioned above and below the

Jan 1, 1981

By Lloyd A. Morley, Alan M. Christman

1. Anonymous. "Getting Down to Earth," booklet 25T, James G. Biddle Co, Plymouth Meeting, Pa. (1970) pp. 1-48. 2. Anonymous. "Megger Ground Tester, Special Instructions," booklet 25-J-1, James G. Biddle Co, Plymouth Meeting, Pa. (1961) pp. 1-16. 3. AIEE Committee. "Application Guide on Methods of Substation Ground¬ing," AIEE Transactions on Power Apparatus and Systems (April 1954) pp. 271-277. 4. AIEE Committee. "Voltage Gradients Through the Ground Under Fault Conditions," AIEE Transactions on Power Apparatus and Systems (October 1958) pp. 669-692. 5. American Standards Association. "American Standard Safety Rules for Installing and Using Electrical Equipment in and about Coal Mines," U. S. Bureau of Mines Information Circular 8227 (1964). 6. Armstrong, H. R. "Grounding Electrode Characteristics from Model Tests," AIEE Transactions on Power Apparatus and Systems (December 1953) pp. 1301-1306. 7. Beck, Edward. Lightning Protection for Electric Systems, McGraw¬Hill, New York (1954) pp. 281-295. 8. Bellaschi, P. L. "Impulse and 60 Cycle Characteristics of Driven Grounds," AIEE Transactions (March 1941) pp. 123-128. 9. Bellaschi, P. L. "Lightning Strokes in Field and Laboratory," Elec¬trical Engineering, Vol. 58 (November 1939) pp. 466-468. 10. Bellaschi, P. L., Armington, R. E., and Snowden, A. E. "Impulse and 60 Cycle Characteristics of Driven Grounds-II," AIEE Tran¬sactions (1942) pp. 349-363. 11. Bewley, L. V. "Theory and Tests of the Counterpoise," AIEE Transac¬tions (August 1934) pp. 1163-1172. 12. Brereton, D. S. and Hickok, H. N. "System Neutral Grounding for Chemical Plant Power Systems," AIEE Transactions on Applica¬tions and Industry (November 1955) p. 315. 13. Bruce, C. E. R. and Golde, R. H. "The Lightning Discharge," Journal of the Institute of Electrical Engineers, London, Vol. 88 (December 1941) pp. 487-505.

Jan 1, 1976

By J. M. Kuchta

Ignition and flammability test methods were developed by the Bureau of Mines for use in the classification of flammable solids by the Department of Transportation. A rotating disk ignition apparatus and a flame-spread-rate apparatus are proposed for determining the ignitability and flammability, respectively, of most flammable solids. Extremely flammable solids, such as pyrophoric materials, are evaluated by determining their ease of spontaneous ignition in an environmental chamber at high-humidity conditions. Data are presented for various representative solids to show the reliability of the test methods for classifying the materials. A classification system is also proposed for use in government transportation regulations.

Jan 1, 1972

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C 2 Complete Hoisting Systems A Above Ground Installations A total of seven companies were identified who supply complete emergency escape hoist units for above ground installations The units have been designed predominately to meet the needs of coal mine operators to satisfy the requirements of the Coal Mine Health and Safety Act of 1969. The seven companies are as follows 1 Dover Conveyor and Equipment Co. 2. Coeur d' Alenes Co. 3. Connellsville Corp. 4. Scott Midland 5. W W Williams Co. 6. Equipment Corporation of America 7. Timberland Ellicott Table VIII contains detailed specifications and price information on each of these units. The units have a number of similarities

Jan 1, 1976

Maps To Accompany Bulletin 507

Jan 1, 1952

By M. W. Price, Joseph V. Mather, E. H. McCleary

"INTRODUCTION The asphyxiation or poisoning of workmen in underground mines by noxious gases from blasting in adjacent strip mines can be prevented.Considerable progress has been made in eliminating or reducing hazards to the health and safety of underground workmen in anthracite mines, but seldom does a year pass without reported cases of underground workmen being poisoned by the fumes from blasts of explosives in strip-mining operations. In the early days of the anthracite industry, the coal near the surface was only partly mined, and many small stumps of pillars and barrier pillars were left standing; these pillars are now being recovered by stripping. It has become necessary to give more consideration to the effects of blasting at strip mines upon the quality of the air in underground mines adjacent to stripping operations.Special precautions are taken by the .personnel of the Jeddo-Highland Coal Co., whose mines are near Jeddo, Luzerne County, and near Centralia in Columbia and Schuylkill Counties in the anthracite region of Pennsylvania, to prevent asphyxiation of workmen by carbon monoxide or other toxic gases resulting from blasting in strip mines. The procedures established by the Jeddo-Highland Coal Co., are given in this circular so that others may benefit thereby and thus avoid hazards to underground workmen where mining is carried on under similar circumstances."

May 1, 1949

By John Ward Smith

An analytical method developed by the Bureau of Mines to determine dawsonite, nahcolite, and nondawsonite alumina (called excess alumina) extractable from Green River Formation oil shales is presented. The method requires water extraction of nahcolite followed by HCI-extraction of dawsonite and an unidentified mineral yielding excess alumina from the water-leached residue. Instrumental determination of sodium in the water extract and sodium and aluminum in the HCI extract measures the sample's content of the minerals. Detailed evaluation shows the method to be adequately specific, precise, and reproducible and free from uncorrectable interferences. The method's results define precisely the production of sodium carbonates and alumina possible from a sample of oil shale and the interval it represents. Shale-oil yields, nahcolite contents, and yields of extractable alumina determined on 83 samples representing an 821-foot section of dawsonite-nahcolite-bearing shale from .Colorado Corehole No.3, drilled in the north part of Colorado's Piceance Creek Basin, are presented. These samples resulted in nahcolite contents to 53.3 percent, oil yields to 48.3 gallons per ton, and alumina yields to 5.80 percent. Use of these data to evaluate the production potential of a section of the formation are suggested.

Jan 1, 1969

Reduce the exposure of diesel vehicle operators to diesel exhaust generated during mucking in deadend drifts. Approach Direct the diesel engine exhaust upward and rearward thereby using the thermal buoyancy of the hot exhaust to form a layer at the roof, above the breathing zone of the vehicle operator. Modifying the Exhaust Outlets Diesel front-end loaders used in nocoal mines to remove blasted ore usually operate in entries open only at one end to cross cut ventilation. These deadend drifts are not usually ventilated with the use of auxiliary fans and vent tubing because of frequent blasting. The existing ventilation, therefore, is usually poor, and a diesel engine operating in such a drift emits exhaust which is not immediately swept away from the operator. On most load machines, the diesel engine's exhaust outlet is located near the floor and directed downward or to the side, so that when the hot exhaust is emitted, it mixes with the mine air as it rises into the vehicle operator's breathing zone. In this way, a uniform concentration of diesel exhaust forms around the operator.

Jan 1, 1983

By John Nagy, Henry G. Dorsett, Murray Jacobson

Laboratory studies show that ignition of a dispersed combustible dust in an open vessel may be prevented by adequate inerting . Factors affecting the inerting requirements are -- dust concentration , spark energy , ignition temperature , composition of the substances used for inerting , fineness of dust and type of combustible . The oxygen concentration of the atmosphere and in some instances the proportion of admixed inert powder and moisture required to prevent ignition are given for 367 dust samples . Variations in inerting requirements with strength of igniting source are discussed .

Jan 1, 1964

By Richard N. Appling

This report presents information obtained by examination and investigation of manganese deposits in northeastern Oregon during May and June 1954 and April 1957. Maps, assays, and other examination data are presented on 10 manganese deposits -9 in Baker County and 1 in Grant County. Included among these deposits are all those that have undergone substantial exploration or have a record of production. Seven of the Baker County deposits occur as characteristically small, irregular pods and lenses in argillite. The remaining Baker County prospects are [marily] narrow, vein-type occurrences in schist. The Grant County occurrence in greenstone and serpentine. All the deposits are composed of various manganese oxides, intermixed with abundant quartz and chert.

Jan 1, 1959

By Roy L. Wilfong

Infrared reference spectra are presented of compounds of importance in lead sulfide flotation research. Included are the spectra of several short chain alkyl xanthates of lead and zinc, the corresponding dixanthogen compounds, and the common oxidation products of lead sulfide and their sodium analogs. The spectra of several frequently used industrial flotation reagent xanthates are also presented. A thorough, well-documented discussion is given of the various corrections made to correct the as recorded absorption band data to near absolute values.

Jan 1, 1974

By H. R. Grau

NIOSH’s Pittsburgh Research Laboratory is currently involved in research to identify silica dust generation in underground metal/nonmetal mines. The ultimate goal of this research is to develop control technologies to reduce worker exposure to respirable silica dust. Commodities and job classifications with the highest silica dust exposure have been identified through analysis of the Mine Safety and Health Administration (MSHA) compliance dust sampling database. Dust surveys were conducted in an underground limestone and gold mine to investigate silica dust sources, generation levels, and controls being used. A summary of the mining operations, sampling procedures, resulting data, and suggested methods to improve the dust control will be provided.

1. In 2003, a total of 1,972 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 13.7% of all mining operations. • Bituminous mines comprised 92.5% (n = 1,825) and anthracite mines 7.5% (n = 147) of coal mining operations. • More than 70% of all coal mines were located in three states: Kentucky (29.0%), West Virginia (20.9%), and Pennsylvania (20.2%). • Bituminous coal mines reported the production of over 1 billion coal tons.

Feb 1, 2005

"A coordinated, integrated research effort aimed at studying the scientific, engineering and medical aspects of the respirable dust problem is underway in the areas of dust generation, dust dispersion and dilution, dust characterization, interaction of dust and lungs, and relationship of seam characteristics to dust generation and mobility. (FIGURE 24) The Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the dust-lung interaction processes that lead to mine worker disability. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines and to other dusts such as diesel-generated.Research projects in the Generic Mineral Technology Center for Respirable Dust have effected several improved methods for the preparation and characterization of the dusts needed by these projects. Superior procedures for generating ""standard"" dust samples have been developed and are in regular use in the laboratory. Questions raised during the course of some projects regarding ""stale"" versus ""fresh"" dust have led to the development of sampling techniques where the dust is directly collected in a surfactant. MSHA and CANMET have requested and received information on Center generated software. An equipment manufacturer, TSI, Inc., requesting input on modifying the inlet of an aerosol sampler has been assisted as a result of research that was conducted at the University of Minnesota.The objectives, scope and progress of all the research projects in the Center, in the form of abstracts and reports, have been detailed in Volume 1 of this series. Research papers written by the principle investigators and resulting from the findings of projects (FIGURE 25) and which are funded by U.S. Bureau of Mines grant number G1135142 have been published in Volumes 3 through 6 and Volume 8 of this series. Volume 2 relates the cooperation and interaction of the U.S. Bureau of Mines and the Generic Mineral Technology Center for Respirable Dust in research on the problem of respirable dust in the mineral industries."

Aug 31, 1989