Search Documents

By A. J. Kraemer

The Bureau of Mines for a number of years has been carrying on an investigation of properties of crude oils from producing fields in the United States and has published a series of reports on different fields, including oil fields of Texas3. Production Data The Spindletop field was discovered in 1901 when the pay sand was found at deaths of about 800 feet. During the following twenty-five years a number of attempts were made to find a deep productive sand. All attempts sere failures until a roll drilled by the Yount Lee Oil Company found oil late in 1925. An intensive drilling campaign began at once, and the production of the Spindletop field increased to a daily average of 93,217 barrels in September, 1926; the present production is estimated at 66,000 barrels doily. Tile following table taken from the Oil and Gas Journal for February 10, 1927, shows the daily average and the total production by ninths for 1926.

Jan 1, 1927

By F. N. Kissell

The applicability of the "direct method" for determining the methane content of virgin coalbeds was tested. Preliminary results indicate that the direct method, when applied to exploration cores, can be successfully used to estimate coalbed gas content and also approximately predict the total gas emission from a prospective mine located in the coalbed at the exploration site.

Jan 1, 1973

By John T. Kuo

The miner's seismic source strength can be approximately estimated on the basis of a single force acting in an infinite medium. Because of the uncertain- ty involved in estimating the amount of conversion from mechanical energy to seismic energy, the source strength thus estimated may be in error by as much as a half-order of magnitude. Calculations of wave transmission must take into account geometrical spreading, dissipation of energy by internal friction, and energy partition due to reflection and refraction of waves impinging on inter- faces in the layered earth. Theoretically derived peak-to-peak particle velocities in microinches per second (PIPS) are given for two models ; viz: (i) 50-feet thick and (ii) 100- feet thick 4000 ft/sec layers with Q = 20, overlying a half-space of 10,000 ft/sec material with Q = 5O;for the cases .of a hammer blow and a timber impact, at the frequencies of 50 Hz and 100 Hz. Comparison of the theoretically derived peak-to-peak particle velocity with experimental data taken at the Copper Queen Mine indicates that the theoretical particle velocity may be overestimated. A discussion of the distortion of seismic wavefronts by mine tunnels indicates that it is unfavorable to use a seismic source impact on the floor of the tunnel, since deceptive delays in arrival time are liable to occur at the surface. A program of parallel theoretical and experimental work is required to clarify uncertainties still associated with the nature and strength of the miner's seismic source signal which cannot be resolved within the approximations of this work. Its major components include theoretical investigations of the (1) Wave diffraction and scattering of an impact source on a face of a cylindrical cavity. (2) Impact of an elastic object on an elastic medium.

Jan 1, 1974

Provide a full-scale test facility where the effectiveness of all types of subsidence abatement techniques can be evaluated under controlled conditions. Background Subsidence is ground movement resulting from the collapse of overlying strata into a mine void because of failure of the mine roof, mine floor, or support pillars. The failure may propagate to the surface and be expressed as a depression, cracks, or a sinkhole. The surface expression of such features may be delayed until long after mining has been completed. Subsidence has the potential to affect more land area than any other type of abandoned mine land problem. Subsidence also causes direct damage to real property, with significant financial loss and more importantly, presents a danger to public health, safety, and general welfare. Subsidence-related problems are considered to be one of the most important abandoned mine land issues. Backfilling of mine voids is the most common stabilization method used to abate subsidence and protect surface structures. Backfilling or placement of material is performed by hydraulic flushing or pneumatic stowing, using either in-mine or remote methods. The majority of the past subsidence abatement projects has been performed using remote methods from single or multiple boreholes. Other subsidence abatement techniques arc available. For example, various point support methods are used to protect small areas of the land surface and surface structures, without completely filling the mine void. These may be more appropriate under different conditions. Little documented information is available concerning the capability of the various backfilling methods for completely filling a mine void or providing long-term structural strength. Therefore, the Bureau of Mines developed a laboratory for controlled evaluation of backfilling technologies.

Jan 1, 1991

By Kyei-Sing Kwong

The U.S. Bureau of Mines investigated the synthesis of advanced ceramics (SiC+AlN, SiAlON, SiC+A1203, and Si3N4+AlN) from natural clays (kaolin, halloysite, or montmorillonite) by an intercalation and heat treatment method. This process includes the steps of refining a clay, intercalating organic chemicals into its layered structure, drying the intercalated mixture, firing the treated structure at certain temperature ranges in controlled atmospheres to form desired compounds, and grinding the loosely agglomerated structure. Focus of this research is to economically process advanced ceramic structures from abundant natural resources. The advanced ceramic phases produced in this simple treatment are homogeneously distributed at the nanostructure level, and may potentially lead to cost effective manufacturing processes. The intercalation of clay was confirmed by X-ray and BET analyses. The evolution of chemical compositions during carbonization reactions and carbothermal reduction was investigated. The characteristics of refined clays and synthesized powders were studied. Advanced ceramic composites/solid solution have been produced from intercalated clays, without the presence of other compounds.

Jan 1, 2010

By R. E. Hall

When the criterion for control of scale prevention on the evaporating surfaces is made the conditions in the concentrated boiler water, then this control becomes an exact operation amenable to an accuracy commensurate with all other operations in the boiler room. The responsibility in boiler water conditioning, however, includes more than clean surfaces. Corrosion in feed lines, economizers and the boiler is a function of the condition of the later, and must be controlled. Steam line and turbine blading deposits must be obviated by the system of conditioning. By the chemical treatment employed, the amount and character of noncondensable uses in the steam must be controlled in accordance with the intended use of the steam. All. in all, the responsibility in boiler crater conditioning ends not with the entrance of the water into the boiler but with the passage from the boiler nozzle of steam, the dryness and rarity of which are defined by the uses to be made thereof. A clearer conception of the scope of boiler water conditioning can be obtained by reference to a diagram of the surfaces (Figure 1) at which it functions. Consideration of this diagram leads to the following outline for the problems of boiler water conditioning: (a) Prevention of scale formation on surfaces (1) In contact with water but at which no evaporation occurs. (2) At which evaporation is occurring.

Jan 1, 1926

By D. A. Reynolds, L. P. Rockenbach

"The method of analyzing light oil for benzene is fully described by Fieldner and others 4/ and Kester and Kolmes 5/. In this procedure, benzene is determined by shaking 20 cc. of the 79º to 81º C. boiling point cut from the fractionation of the refined light oil with 3 volumes of 98—percent sulfuric acid in an A. S. T. M. separator funnel of the type used for determining water in bitumi¬nous materials. After the mixture has been shaken 5 minutes it is allowed to settle at least half an hour and the acid is drawn off; the residual oil is reported as paraffins and the decrease in volume as benzene. The method has been found satisfactory for light oils from coals carbonized at 5000, 600°, and 7000 C. but does not give accurate, reproducible results for oils from the 800° C. tests.The content of benzene of the 790 to 81° C. cut is high, 90 to 95 percent, for 800° C. light oils, whereas for lower—temperature light oils it is considerably less. Benzene is the most difficult of the aromatics to sulfonate, hence the acid concentration must be maintained above 95 percent to insure complete sulfonation. Sulfuric acid (98 percent) reacts with benzene, but its reaction with paraffins at ordinary temperatures is negligible; however, more concentrated acid will attack paraffins and give erroneous yields of benzene. The reaction between benzene and sulfuric acid forms water that will dilute the acid. The effect of this dilution may be overcome by increasing the acid-to-oil ratio or increasing the strength of the acid. The latter, however, must not be used, because the stronger acid reacts with paraffins."

Mar 1, 1942

By R. H. Storch

The work described in this report was part of a Bureau of Mines program to appraise the titanium-mineral resources of Idaho. Part of the program included churn drilling of alluvial deposits that previous preliminary testing, primarily for rare minerals, had indicated to be potential sources of titanium minerals. The first spot churn drilling began in the Deadwood placer area, Valley County, Idaho, in July 1956 to determine both the amount and grade of the ilmenite, FeTi03. Ten holes, ranging in depth from 6 to 40 feet and aggregating 251 feet, were drilled; 54 samples were taken. The samples were sent to the Spokane field laboratory for concentration and visual estimation of the amounts of the more common minerals in the heavy sand concentrates. For specific determinations samples from each drill hole were composited and shipped to the Bureau of Mines laboratory in Albany, Oreg., where petrographic, quantitative X-ray spectrographic, and chemical analyses were made.

Jan 1, 1958

To provide coal operators with an easy-to-use stress control design procedure to minimize coal mine bumps during room-and-pillar retreat mining conducted with available continuous mining machine technology. Approach The goal of this U.S. Bureau of Mines (USBM) re¬search was to facilitate safe and efficient room-and-pillar retreat mining of bump-prone coalbeds by limiting coalbed stress adjacent to expanding gob areas through variation of section layouts. The first step was design of total-extraction pillars and their associated pillar-extraction plans. The second step was development of a coalbed strength model. The third step was development of stress limit design criteria. The fourth and final step was development of a methodology to estimate the magnitude and distribution of development and abutment loads apllied to the pillar line. The linear geometry of unlimited-width sections allowed for the accomplishment of step four with the tributary-area and linear shear-angle concepts. Increasing overburden depths required limited-width sections separated by barrier pillars to control stress within total-extraction panels. The accomplishment of step four with limited-width section designs required prediction of abutment load distributions for rectangular gobs and apportionment of these loads over mixed pillar sizes. A parametric study of the complicated interaction of various combinations of overburden depths, total-extraction panel widths, and abutment pillar widths was conducted with the USBM-developed boundary-element program MULSIM/NL.

Jan 1, 1995

By Manuel Gomez

The mean and the standard deviation were used to describe general sulfur and ash populations as well as specific populations of these variables from one coal seam. Both the mean and the standard deviation were incorporated in the exploration process to determine the number of drill cores necessary for seam evaluation and to guide the sequential drilling plan. Probability regions were computed to establish a basis for predicting probable ranges of average sulfur and ash concentrations that may be expected upon continued or future drilling. A computerized plot program was utilized to interpolate sulfur and ash concentrations between grid points. The plot program, which is essentially a moving average technique, permits a rapid evaluation of sulfur, sulfur forms, and ash spatial distributions as a drilling program progresses sequentially. This information, in the form of contour plots, can be made available to both the mining engineer and the fuel technologist in advance of mining to outline reserves, to improve selective mining, and to anticipate preparation facilities.

Jan 1, 1972

Provide a means of recovering precious metal values from finely ground tailing materials. Approach Determine the procedures needed for agglomerating the finely ground material for subsequent heap-leach cyanidation of the precious-metal-bearing tailings. Applying Agglomeration/Heap-Leaching to Fine Tailings Agglomeration technology was developed by the Bureau of Mines to provide cost-effective recovery of precious metal values though better heap leaching of clayey or low-grade ores. While many precious metal producers have adopted this technology to reclaim precious metals from crushed ores and wastes, other operations have experienced problems in using the heap leaching technique effectively on piles of fine tailings. In contrast to the coarser ore and waste material, most tailings piles contain more than 50 percent minus 200 mesh materials with no coarse material. Fine particles and clays present in the pile can impede 8 uniform flow of the leaching solution through the heap, thus preventing efficient and cost-effective precious metals recovery.

Jan 1, 1986

By d&apos, Kathleen J. Amico

This summary appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1967

By Harold L. Rhodes

The Bureau of Mines has developed a quantitative method to determine water vapor in helium in the range of 0.1 to 15 ppm by volume. This method uses the quantitative chemical reaction of H20 with CaH2, which produces 1 mole of hydrogen for each mole of H20 in the sample. A gas chromatograph is then used to determine the concentration of hydrogen in the product. The precision of the H20 analysis is ±0.05 ppm at a concentration of 1 ppm. This method is used to calibrate a commercial platinum-phosphorus pentoxide (Pt-P205) electrolytic water vapor analyzer that has an improved inlet system and digital voltmeter readout.

Jan 1, 1981

By Martin J. Gavin

During the recent study of lubricating oils carried on in the San Francisco laboratory of the United States Bureau of Mines, it became desirable to distill the oils used in the experimental work at pressures as low as 10 millimeters (mercury column) absolute. In the effort to Overcome difficulties and eliminate sources of error, certain changes were made in the apparatus for vacuum distillation used by the Bureau of Mines for crude petroleum.4 These changes were described in R.I. 2819, issued in July, 1927. Subsequent to the publication of R.I. 2819 several other changes have been made, and the present form of the apparatus for vacuum distillation of lubricating oils is described in this revision of R.I. 2819. These changes were found to give more accurate checks on duplicate distillations. The major part of the credit for the laboratory work which developed the changes in the apparatus and method revised herein is due to Boyd Guthrie, assistant petroleum chemist, and R. V. Higgins, junior chemist, o the San Francisco laboratory, United States Bureau of Mines. DESCRIPTION OF APPARATUS The distilling flask employed is essentially the Hempel flask as used by the United States Bureau of Mines for the analytical distillation of petroleum.5 he complete apparatus is shown in Figure 1. The fractionating column and exposed portion of the flask is wrapped with 4 inch asbestos rope and then surrounded by a cylindrical hood of 1/8 inch pliable asbestos sheet with a narrow air space between the wrapping and the cylindrical hood. This was found necessary to prevent any radiation or convection heat losses from the column, and resulted in obtaining a more even and constant fractionation by eliminating any dephlegmating action caused by temperature changes around the column.

Jan 1, 1930

By B. W. Madsen

A nearly dormant copper sulfide pilot-scale experimental leach containing 8.7 tons of are was injected with oxygen to determine its effect on the copper-leaching rate. Prior treatment of the uncrushed 0.25-percent-copper, mine-run stripping material consisted of 461 days of acid ferric sulfate leaching, which extracted 47 percent of the total copper. The permeability of the bed had decreased, and the percolation rate had decreased from an initial 20 gallons to 0.8 gallon per square foot per day. Copper extraction had nearly stopped. After injecting oxygen into the ore column and leaching for 30 days, the percolation rate was increased to 6 gallons per square foot per day. In an additional 298 days of leaching, an additional 40.7 percent of the copper was extracted. The improved leaching after the use of oxygen is attributed to stimulated bacterial action, better oxidation, and increased permeability.

Jan 1, 1975

By P. T. Brooks

The selective recovery of nickel and cobalt from impure raw materials is being investigated by the Bureau of Mines as part of a program to develop improved procedures for preparation of pure metals. A combination solvent extraction-electrolytic process has been developed in the laboratory that enables preparation of high-quality nickel and cobalt from nickel oxide containing, in percent, 76 nickel, 0.8 cobalt, 0.5 magnesium, 0.2 iron, and lesser quantities of copper, zinc, and other metals. The oxide was smelted, using carbon as reductant, and cast into anodes. These anodes subsequently were dissolved in diaphragm-type electrolytic cells. Nickel and cobalt were deposited separately from appropriate electrolytes, concurrent with dissolution of the impure anodes. Anolyte containing nickel and cobalt in the form of chlorides and sulfates was treated for removal of impurities and separation of nickel and cobalt. First, iron and aluminum were removed as hydroxides by adding nickel hydroxide to raise the pH of the anolyte from 2.3 to 4.5. Next, the pH was adjusted to 2 by adding hydrochloric acid, and the solution was treated by solvent extraction to separate nickel and cobalt.

Jan 1, 1963

By W. A. McKinney

A sample of oxidized copper ore from a large deposit located in Pinal County, Ariz., about 50 miles northeast of Tucson, was treated by the Federal Bureau of Mines in a small-scale continuous pilot plant by a procedure which comprised acid curing complemented by water leaching and countercurrent decantation washing in a series of drag classifiers. A feed was prepared by pugging minus 1/4-in, ore with concentrated sulfuric acid and about 10 pct, of eater, followed by curing in batches for about 24 hr. The cured ore was fed continuously to a leach drum, where it was mixed with advance solution from the countercurrent washing system to dissolve the sulfated copper. The pulp was thickened and washed in four Esperanza-type classifiers, using a flocculating agent to obtain rapid settling and thickening. The leached ore pulps thickened satisfactorily in the drag classifiers when about 0.8 lb. of a polyacrylamide flocculant per ton of dry feed was used. Clear overflow liquors were obtained, and classifier rake products containing about 60 pct. solids were produced, As much as 90 lb./hr. of ore was treated in the plant, with a recovery of 60 pct. of the total copper or 80 pct, of the acid-soluble copper when 2 tons of water per ton of feed was used in washing. The acid consumption was 4.3 lb./lb. of copper recovered. On the basis of the maximum feed rate employed and the effective pulp-settling area of the classifiers, a total of 1 sq. ft. of pool area was required per ton of dry feed per day for the thickening and washing operations. The washing efficiency in the test was 95 pct.

Jan 1, 1960

By Lars Osen

The Bureau of Mines investigated (1) the effect of torsion on yield and ultimate strengths of bolts when the torsion is applied first and tensile load is applied independently of torsion and (2) various methods of increasing the tension-torque ratio and/or narrowing the data spread of the tension-torque relationship. A special torsional attachment was fabricated to attach to a universal testing machine to independently subject rock bolts to combined tensile and torsional loads. It was found that initially installed torsion is nullified during tensile loading and the tensile yield and ultimate strengths are not significantly reduced. Lubricating various components of a bolt assembly or using hardened washers will improve the tension-torque relationship during conventional installation; however, the torsional load is not nullified during this type of loading. Hence, a bolt is subjected to a combined stress throughout the loading cycle; the yield point will thus be lowered compared with the pure tensile yield if care is not taken during installation to stay below the torsional yield.

Jan 1, 1966

By R. W. Stahl, H. E. Sanford, J. B. Benson

"As movement or transportation of coal is second only in importance to actual mining, and as the latter is wholly dependent on the former, the efficiency of the haulage system often determines the efficiency of the entire plant. Safe or accident-free transportation is essential, also, because no attempt is made to divorce safety and efficiency, it being realized that they are inseparable.Most of the Ruhr mines were opened decades ago, and many features that were considered up-to-date then are now obsolete. Progress in developing haulage systems has been slow, chiefly because it would be very costly to change many to accomodate more modern equipment. These systems are being altered or modernized slowly, as capital permits. The only revolutionary changes that have been made in mine haulage are the use of larger locomo¬tives and cars, in the movement of shuttle cars, and in the adoption of skip hoisting. Most Ruhr shafts, however, will not accomodate large cars, the secondary roadways are too narrow for large locomotives, and the coal is too soft to permit skip hoisting because degradation would be too great. Therefore, notable advances have been made only at newer plants, where allowances have been made for modern equipment.The shafts are deep (average 2,300 feet) and of comparatively small diameter. The small bore was designed to reduce costs of sinking and lining. Generally, the shafts are lined throughout with masonry; however, most of the buntons and guides are wooden.The hoisting engines arc installed in masonry structures, and where more than one hoist is used they are placed on opposite sides of the shaft to eliminate as much noise as possible (fig. 1). This arrangement also prevents an engineer from acting on any signals except those transmitted to him. A few hoisting engines are mounted in the headframes (fig. 2). The hoisting engines are equipped with overwind, overspeed, and auxiliary braking devices, which are tested frequently and kept operative at all times. The signal code is displayed in view of the engineer, and a light or dial indicator informs him of the cage's position in the shaft. Many hoists are equipped with re¬cording devices, which show on a continuous chart the speed of hoisting as well as any delays throughout the 24-hour period.A Koepe system of winding is in general use because of the depth of shafts (fig. 3). With this system, a single rope passes over a single-groove, large-diameter sheave attached to the motive power, and the ends of the rope, after passing over the head sheaves, are attached to the cages. A flat tail rope suspended in the shaft and connected to the bottom of the cages serves to balance the system. Both steam and electric engines are used to activate the hoisting system, end the engines are capable of moving at least a 50-percent overload.The ropes are necessarily of large diameter (2-1/2 inches and greater), and flexibility decreases as rope diameter increases. To overcome the unwieldiness .of large-diameter ropes as shafts become deeper, a four-rope system is being tried at one mine (fig.4). In this system the load is equalized between four ropes which permits much smaller ropes to be used. All hoist ropes are inspected daily and discarded after 2 years service unless special permission for longer service is granted by the Mine Inspectorate, and then only after thorough visual and electromagnetic inspection."

Jan 1, 1950

By M. Kanefsky, A. Q. K. Rajput

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties but on the precise shape of the cross-correlation functions between the noise inputs. By using two polarity difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 11, 1981