Search Documents

By Fred N. Kissell

Methane concentration peaks were measured by the Bureau of Mines at coal mine working faces during entry development. The statistical distribution of peaks was found to be normal or log normal depending on how well the methane was being mixed into the ventilation airstream. A normal distribution indicated good mixing, whereas a log-normal distribution indicated that mixing was poor. In addition, the "highest" peaks over selected intervals were found to fit a type I extreme-value distribution, a result similar to that obtained while mining longwall faces.

Jan 1, 1974

By Murray Jacobson

The Federal Coal Mine Health and Safety Act of 1969 established mandatory dust sampling of coal mines according to procedures prescribed in the Mandatory Health Standards, title 30, Code of Federal Regulations, part 70, published in the Federal Register on April 3, 1970. A laboratory was established in the Pittsburgh Field Health Group of the Bureau of Mines to process the coal mine dust samples collected by the mine operators. This paper describes the laboratory and presents the equipment and procedures used in processing these samples.

Jan 1, 1971

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

To suppress the natural bacterial action in acid mine drainage (AMD), the major contributor to acid formation. Approach Recycle partially-treated affluent back to the source of AMD within a mine, or to the coal or coal-waste stockpile. This effectively eliminates any further biologically-promoted AMD by inhibiting catalyzed weathering or oxidation by acid-forming bacteria. How it Works AMO-type effluents can be largely reduced by "recycling" the acidic outflow back to the source of AMD within a mine or to the Input side of a waste pile to percolate through the reactive pyrite and bacteria mixture. The bacteria in the cell thrive on the oxidation of ferrous to ferric iron through the electron transfer, Fe2 +[=]Fe3 + + e. Its reaction product [s, therefore, essentially ferric iron. While small quantities of Fe3 + will not interfere with the exponential multiplication of the bacteria

Jan 1, 1982

By Noel N. Moebs

The Bureau of Mines investigated severe coal mine roof support problems along a section of main entries in the Pittsburgh coalbed in southwestern Pennsylvania to identify the causative factors. The mine roof was examined in detail, and various sedimentary structures are described that contributed directly to irregular and unstable roof. Small-scale paleochannels, scours, and related slickensides were identified as the leading cause of bad roof, and isopach maps were prepared to illustrate a method whereby the presence of these structures could be inferred in advance of mining. Probably second in importance was the occurrence of relatively incompetent flaggy, poorly cemented sandstone, weakened by coal and micaceous laminea. No effect of in situ stresses on roof stability was detected.

Jan 1, 1977

By Lloyd A. Morley, Alan M. Christman

PART A. ELECTRICAL EQUIPMENT – GENERAL Paragraph 1. Electrical Equipment; Examination. All electric equipment shall be examined, tested, and properly main¬tained by a qualified person to assure safe operating conditions. The examinations and tests shall be performed at intervals not exceeding six (6) months unless otherwise specified in Parts A, B, C, D, and E. When a potentially dangerous condition is found on electric equipment, such equipment shall be removed from service until such condition is corrected. A record of such examinations shall be kept and made available to an authorized representative of the Secretary and to the authorized repre¬sentative of the miners in such mine. Each item of major equipment, in¬cluding substations, switchgear, load centers, and so forth except powered hand tools, shall be recorded separately. The record of such examination shall include all dangerous conditions found, corrective action taken, and name of examiner, and shall be signed by the person responsible for main¬taining the equipment in safe operating condition, who shall also be a qualified person. Paragraph 2. Electrical Work; Qualified Personnel. No electrical work shall be performed on electrical distribution circuits or equipment, except by a qualified person or by a person trained to perform electrical work and to maintain electrical equipment under the direct supervision of a qualified person. Disconnecting devices shall be locked out and prominently tagged by the persons who perform such work, except that in cases where locking out is not possible, such devices shall be opened and prominently tagged by such persons. Locks and tags shall be removed only by the persons who installed them or, if such persons are

Jan 1, 1976

By H. O. McDonald

The Bureau of Mines has demonstrated a hydrometallurgical method to separate chromium from other metals in a variety of surface-finishing wastes by precipitation with benzoate ion. The resulting chromium salt may then be converted to the hydroxide, and the benzoate may be recycled. Chromium recoveries of 92 to 100 pct are obtained.

Jan 1, 1983

By D. S. Colby, E. M. SEELEY

The total production capacity of the natural-gasoline industry increased to 27,212,000 gallons (647,905 barrels) daily on January 1, 1950, from 21,322,000 gallons (507,670 barrels) daily on January 1, 1948. The rate of growth during these 2 years averaged 13 percent per year, compared with 9 percent per year from 1946 to 1948 and 6 percent from 1944 to 1946. The total number of operable plants on January 1, 1950, was 554, 5 more than at the beginning of 1948. The number of absorption plants increased by 12, the number of cycling plants by 7, and the number of combination plants by 4. The number of compression plants and charcoal plants continued to decrease. Absorption plants accounted for 67 percent of the total capacity on January 1, 1950, compared with 62 percent 2 years previous. Eighty-two per- cent of the expansion in these 2 years was in absorption-plant capacity. Cycle plants accounted for 24 percent of the total industry capacity at the beginning of 1950, compared with 27 percent on January 1, 1948. The average daily capacity of absorption plants increased from 38,400 gallons at the beginning of 1948 to 50,600 gallons at the beginning of 1950. During the same period, the average daily capacity of cycle plants decreased from 150,200 gallons to 144,100 gallons. Texas showed the largest gain in number of plants 13 absorption, 4 compression, and 4 cycling plants. The State accounted for 67 percent of the gain in capacity and on January 1, 1950 had 50 percent total national capacity. Louisiana followed with 7 additional plants. Pennsylvania reported 14 and West Virginia reported 13 fewer plants than in 1948. Most of these reductions were in the number of compression plants.

Jul 1, 1950

By R. Barany

The heats of formation of goethite, ferrous vanadate, and manganese molybdate at 298.15° K were determined by solution calorimetry. For formation from the elements, the heat values were -133.7 ±0.3 kcal/mole for goethite, -453.8 ±0.5 kcal/mole for ferrous vanadate, and -284.8 ±0.2 kcal/mole for manganese molybdate. For formation from the oxides, the heat values were -0.9 ±0.1 kca1/mole for goethite, -19.4 ±0.3 kca1/mole for ferrous vanadate, and -14.6 ±O.l kcal/mole for manganese molybdate.

Jan 1, 1965

By Stephen A. Swan

Bureau of Mines researchers have collected and evaluated rollover protective structures (ROPS) f or more than 10 yr. ROPS and falling object protective structures (FOPS) are required on specified mining machines under regulations of the Mine Health and Safety Administration (MSHA). Both ROPS and FOPS are required on mining machines used in surface coal mines and surface areas of underground coal mines (30 CFR 77.403 and 7 7.4 13a), and ROPS are required on mining machines used in metal and nonmetal mining operations (30 CFR 55, 56, and 57.9-88). This illustrated manual provides mine safety personnel, MSHA inspectors, and original-equipment manufacturers with guidelines and a check- list for inspecting ROPS being used in the field. The manual discusses specific requirements of the MSHA regulations and minimum inspection and maintenance checks for ensuring compliance with those regulations. An easily reproducible checklist is provided as an aid to the inspection of ROPS.

Jan 1, 1985

By Oliver Bowles

"A Product from Mica Mines.Mica commonly occurs in pegmatites which consist of large crystals of feldspar and quartz, mica constituting but a small proportion of the total rockMuch of the feldspar thus thro n out during the process of mining is pure and of high quality, end the Bureau of Mines has suggested that much of it could be utilized for ceramic purposes. Encouragement is given to such utilization by the fact that several mines now worked for mica were formerly operated for the production of feldspar. ""'here mines are not readily accessible to railroads feldspar utilization might not be feasible, for it is a much lower priced product than mica and cannot therefore bear as heavy transportation expense. '""here mines ire located close to railroads, however, such utilization would tend to reduce the cost of mica mining, and at the same time assist in the solution of the waste disposal problem.The Bureau has recently been informed that some of the feldspar from mica mines near Spruce Pine, N.C., is now being sold and shipped away. An extension of this by-product industry is to be recommended.A Mica Deposit in New York City.The Bureau recently received a mica specimen obtained from a. building excavation at 157th St. and Riverside Drive, New York City. The specimen was about 2 by 4 inches in size, and fairly clear though containing numerous hair cracks. It was obtained only 7 or 8 feet below street level. At greater depth and with more careful methods of excavation material of much better quality might be obtained. The material submitted could be used for mica washers but not for sheet mica. It is stated by an official of a prominent mica company that many such fragments are obtainable in this locality and the possibility of the occurrence of a good mica vein is thereby suggested."

Jun 1, 1920

By H. R. Shell

The systems MgO-MgFa-SiO2, at 2 and 4 weight-percent Li2O and at 3.8 and 7.7 weight-percent Na2O were investigated by solid state reaction at 1,200° C. The results are summarized in four ternary diagrams. Besides the expected humites and simpler silicates or fluorides, proto-amphibole and water-swelling fluormicas or fluormontmorillonoids were found in the systems containing lithium and monoclinic fluoramphiboles, water-swelling fluormicas or fluormont-morillonoids, and nonwater-swelling fluormicas were found in the systems containing sodium. These latter compounds were not in the base system MgO-MgF2-SiO2.

Jan 1, 1962

"INTRODUCTIONMany of the facilities and much of the equipment available to the Generic Mineral Technology Center for Respirable Dust are highly specialized and therefore, unique to the universities associated with the Center as illustrated in FIGURES 30 through 39.For example, a sample bank of 1300 U.S. coal specimens housed in the Coal Research Section, Deike Building of The Pennsylvania State University has been characterized for physical, elemental, mineralogical and maceral compositions. The results of this research have been used to initiate a study of the relationship between pneumoconioses and coal properties. Selected samples from this bank have been used in animal (primate) studies at the Milton S. Hershey (Penn State) and West Virginia University Medical Centers. These laboratory facilities for research in the medical and biological disciplines is state-of-the-art and includes a primate colony where dust research is currently underway. The Materials Research Laboratory and the Rock Mechanics Laboratory at PSU, and the Mechanical Systems Design and Control Laboratory, the Rock Mechanics Laboratory and the Mine Electronic System Laboratory at WVU are equipped for fundamental research on dust generation and characterization. While the majority of respirable dust research projects fall into these two categories, dust generation and characterization and interaction of dust and lung, there are other laboratory facilities available to the Center which are unparalleled in the type of equipment and expert personnel that they contribute to the program. The Mine Particle Laboratory located at the University of Minnesota and the Diesel Engine Laboratory at Michigan Technological University are examples. They house equipment and instrumentation that is unique to these facilities. much of it having been developed specifically for dust research by the research scientists there. The dust collection equipment and the fine particles measurement, characterization and analysis apparatus are essential to research in the areas of dust collection, particle characterization and diesel particulates. In addition to university laboratories, the research facilities of the National Institute for Occupational Safety and Health (NIOSH) are available to the Center through its relationship With West Virginia University."

Aug 31, 1989

By R. J. Matetic

Researchers associated with the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), are investigating injuries (fatal and nonfatal) attributed to water well drillers during well drilling activities. Injury data, obtained from various sources, suggest that many water well drillers are experiencing unnecessarily high insurance premiums and very avoidable citations or violations from the direct result of accidents, injuries, and fatalities occurring throughout the water well drilling industry. Expensive insurance premiums and unnecessary citations are the direct result of poor health and safety practices. Visits to numerous water well drilling sites were conducted by NIOSH personnel to characterize and identify the injury data collected and to provide inexpensive strategies to prevent, minimize, and eliminate safety and health issues associated with water well drilling activities.

Jan 1, 2001

By James P. Rider, Jay F. Colinet

The National Institute for Occupational Safety and Health (NIOSH) has conducted benchmarking surveys at longwall operations across the country to identify current operating practices and the types of controls being used. Gravimetric and instantaneous dust sampling was completed to quantify dust generation from major sources and determine the relative effectiveness of the different control technologies. Results from the underground dust surveys will be presented as an update on longwall dust control technology and operating practices.

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

BIBLIOGRAPHY 1. Dougherty, John J. , "Control of Mine Fires", Publication of the Mining Extension Service, School of Mines, Appalachian Center, West Virginia University (1969). 2. Coal Age, "Fire, Explosions and Recovery, Federal No. 1 Mine", November, 1963. 3. Nagy, et al., "Sealing a Coal Mine Passage through a -Nor-ii-hole: A Progress Report", U.S. B. M. Publication No. 6453, (1964). 4. Murphy, et al., "Use of Fly Ash for Remote Filling of Underground Cavities and Passageways", U.S. B. M. Publication No. 7214, (1968). 5. Pennsylvania Drilling Company, Pittsburgh, Pennsylvania. Personal Review of Equipment. 6. Industrial Hazards and Communication, Division of U. S. B. M. Personal Communication with John Murphy and Merle Bowser. 7. Instrument Technology, Inc., Borescopes and CCTV Systems for Inspections of Nuclear Reactors; Personal Communication. 8. "Public Works", July, 1972. 9. The Industrial Hazards and Communications Division of the U.S. B. M. , Personal Communication regarding Cohu Model No. 2006. 10. "Bibliography on Underwater Photography and Photogrammetry", Eastman Kodak Pamphlet No. P-124. 11. Optical Properties and Visual Effects of Smoke-Stack Plumes, U.S. Department of HEW, 1967. 12. Middleton, W. E. K. , "Vision Thru the Atmosphere", Univ. of Toronto Press, 1952. 13. Kodak "High Speed Infra Red" film and Singer Corporation Model TI Silicon Vidicon TV Camera. 14. Night Vision Laboratory, Fort Belvoir, Maryland; Barnes Engineering Company, Stamford, Connecticut, Model, T-101; AGA Inc. , Secaucus, New Jersey, Model, "Thermovision" 680.

Jan 1, 1973

By David R. Hanson

Transient electrical noise events pose serious problems for data acquisition systems used in monitoring acoustic emissions in laboratory and field environments. The U.S. Bureau of Mines has designed and constructed a trigger discriminator circuit for use in ultrasonic acoustic emission studies. Designed for use with signals in the frequency range of 50 to 400 kHz, the instrument examines .incoming signals for frequency content, amplitude, simultaneity, threshold crossings, and number of channels above threshold. If preselected criteria on these properties are met, a plus 5-V pulse is output that may be used to trigger a data acquisition system, allowing rejection of noise events that do not possess useful information. The system was designed for four input channels, but may be expanded to more channels with minimal design changes.

Jan 1, 1995

By D. B. Dow

"Natural gas-gasoline is made by collecting in the liquid state the condensable hydrocarbon vapors that exist in different natural gases in varying amounts. In the richer type of natural gas the gasoline is generally recovered by compression and cooling. If exceedingly high pressure or low temperature is used, there is dissolved in the gasoline a large amount of very volatile material, which evaporates rapidly at atmospheric temperature and pressure.In the leaner type of natural gas, the gasoline vapors are selectively absorbed from the permanent gases by passing the natural gas through an absorbing oil. The gasoline is recovered by distilling the saturated oil, and as compared with ""compression"" gasoline is of high Baume' gravity and low vapor pressure. Before a volatile gasoline can be transported in tank cars, it is necessary to decrease its volatility in order to lessen the risk of fire or explosion, as well as to prevent excessive evaporation in transit. This can be accomplished either by weathering the gasoline, or by blending it with a more stable material, naphtha being commonly used in the weathering process the more volatile portions of the gasoline are allowed to evaporate and the losses in volume are very large, therefore, blending is preferable, wherever possible.It is very difficult, however, to produce by blending, in gasoline plants, a motor fuel which is equal to straight-run refinery gasoline. In order to make a blended motor fuel of a grade equal to straight-run gasoline, only a small percentage of natural gas-gasoline can be blended with the naphtha, consequently it is customary to blend the gasoline with only enough naphtha to enable It to be shipped to an oil refinery when the material is again blended to form a finished motor fuel."

Sep 1, 1921

By K. O. Bennington

The thermodynamic properties of synthetic acmite, NaFe3+Si206, were determined by the Bureau of Mines. The enthalpy of formation was determined by hydrofluoric acid solution calorimetry. The values of the standard enthalpy of formation at 298.15 K, ?Hf°298.15, from the elements and from the oxides, ?H°298.15, are ?Hf°298.15 = -615.87 ±0.71 kcal/mole, ?H°298.15 (from oxides) = -32.08 ±0.53 kcal/mole. Various experimental data were combined with other data from the literature to calculate all the related thermodynamic properties in the range of 298 to 1,263 K. The standard Gibbs energy of formation is ?Gf°298.15 = -575.8 kcal/mole.

Jan 1, 1981

By Edwin M. Thomasson

Helium shipments for 1965 exceeded the volume shipped during the previous year for the 16th successive time. Shipments from Bureau of Mines helium plants were 698.6 million cubic feet, 2 about 4.7 percent more than in 1964. Production at Bureau of Mines plants totaled 757.4 million cubic feet, and an additional 3,549.6 million cubic feet was produced by private companies participating in the helium conservation program and purchased by the Bureau of Mines and stored underground for future use. The Bureau of Mines continued to sell helium at $35 per thousand cubic feet, the price established in 1961. Production and sales of helium increased from the one private plant operating entirely outside the Government's helium program. A second private plant was virtually complete at yearend, although actual production had not commenced.

Jan 1, 1967