Search Documents

In 1991, the USBM (U. S. Bureau of Mines) evaluated the mineral resources of the 174,550-acre Bear Creek-Poker Peak area. Located 40 air miles east from Idaho Falls, ID, the study area is in the Caribou National Forest but is mostly administered by Targhee National Forest. USBM personnel mapped and sampled mines, prospects, and mineralized sites in and near the study area. Five types of mineral occurrences were identified in the study area: phosphate, limestone and travertine, placer gold, coal and uranium (the latter contained in the coal), and oil and gas. The study area has a high potential for oil and gas; evaluation of these commodities were beyond the scope of this study.

Jan 1, 1992

By Robert H. Peters

This U.S. Bureau of Mines report identifies the types of serious accidents that occur most frequently at small underground coal mines and describes the strategies that could help prevent these accidents. A wide variety of methods for improving safety are suggested, including improvements in the design of equipment, work procedures, work schedules, safety programs, and emergency response plans, as well as techniques for diagnosing the potential hazards associated with new technologies and work procedures. Some of the papers in this volume focus on preventing specific types of mining accidents--ones associated with materials handling (primarily back injuries), equipment maintenance, improper machine guarding, and ground failure during retreat mining. Although the recommendations in this volume are heavily influenced by research performed at underground coal mines in the Appalachian coalfields, most of the papers contain advice that is equally pertinent to almost any type of mine.

Jan 1, 1994

By Jack D. Ramsdell

Electrorefined, magnesium-reduced, and sodium-reduced titanium samples were evaluated for recrystallization behavior, effect of cold rolling on tensile properties, and bend ductility. Curves were determined for the softening of 2.5 to 80 percent reduced cold-rolled metal that was annealed over a temperature range of 300° to 800° C. Upon annealing, coarsening of the grains was found to occur for reductions in thickness of less than 20 percent in titanium made by all three processes. The presence of metallic impurities greatly inhibits coarsening for reductions in thickness below 20 percent, but for reductions in excess of 20 percent grain size is essentially constant at each annealing temperature. The three grades of titanium did not harden excessively from cold rolling; both tensile and bend ductility were good for reduction in thickness up to 80 percent. Upon annealing, softening occurs between 400° and 600° C., and, based on microstructure and property studies, full annealing is accomplished after 30 minutes at 700° C. for the magnesium-reduced and electrorefined titanium and at 800° C. for the sodium-reduced titanium.

Jan 1, 1960

By Eliot J. White

The Bureau of Mines tested cores from 35 wells from 14 oil-producing zones in southern Illinois, southern Indiana, and western Kentucky to determine why rates of water injection were apparently low in some zones. Since these zones contain only minor amounts of clay minerals, it is concluded that permeability reduction results from movement of dislodged silica particles and other material, including the clays, that lines the pores. Both single-phase and two-phase permeability measurements, however, indicated that most samples had only low to moderate water sensitivity, so that permeability reduction due to such particle movement should usually not be of practical significance. The effective permeability to water was considerably lower than the effective permeability to oil during two-phase flow measurements, as is typical of most reservoir rocks. It can be concluded, therefore, that relatively high injection pressures will be required in waterflooding thin zones or zones having low permeabilities.

Jan 1, 1966

By E. C. Lane

The motor gasoline that is being marketed in the United States this winter is practically the same 'as that sold a year ago. In fact, there has been little char sin this commodity during the year, as the gasoline sold last summer was almost as volatile as that marketed last winter. Boring the past eight years, the Bureau of Mine's has made semi-annual surveys of the gasoline marketed in the United States, the survey just completed being the fifteenth in the series. The cities in which samples have been collected have been chosen as representative of the more important marketing territories as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country.

Jan 1, 1927

By Oliver Bowles

The conservation of fuel became a critical problem during the recent war, particularly in the East. Fuel-oil supplies were short, the demands for coal increased, and householders were called upon to reduce the temper- atures in their homes. Home owners were urged to employ every means avail- able to reduce fuel consumption, the most important of which was to insulate their dwellings. The Bureau of Mines, United States Department of the In- terior, took steps to promote the conservation of fuel by issuing a report3/ on home insulation which has been widely circulated. The American populace responded patriotically to the requests of various Government agencies for voluntary conservation of fuels; they accepted cheerfully the restrictions imposed, the crisis was weathered, and with termination of hostilities the unhappy situation was relieved. Fuel conservation, however, is not merely a war emergency problem; it is a continuous, ever present issue. Coal and petroleum resources are ir- replaceable assets, and when fuel is burned it is exhausted - there is no scrap recovery. Fortunately, the United States has been richly endowed with mineral fuels; but population is growing, industrial demands for fuel are increasing, and mines and oil wells are becoming deeper and more costly to operate. For the sake of generations to come all national resources, particularly irreplaceable fuels, should be conserved. A long step in the direction of fuel conservation is the general rec- ognition that insulation is an essential element of dwelling construction. Fortunately, when the home owner takes measures to conserve fuel, he is not called upon to make purely unselfish (altruistic) sacrifices to advance the general welfare; he has the added incentives of saving money and promoting more comfortable living in his own home.

Oct 1, 1946

By Robert C. Bates

This Bureau of Mines report converts published data on the cost of ventilating uranium mines to a common price base and analyzes these data to determine the cost per ton of uranium ore at various levels of radiation exposure control. There appears to be an exponential increase of cost as the radiation level is lowered. The 1967 base costs are extrapolated to present dollars, and some cost comparisons are given for other radiation control measures.

Jan 1, 1981

By Frank W. Sansom

This paper is one of a series of articles dealing with milling methods and costs at metal mines in the United States, written in accordance with an outline prepared by engineers of the United States Bureau of Mines and published by the bureau. The Netta mine and concentrator is the largest of the plants of the Eagle-Picher Lead Co, It is located in Ottawa County, in the extreme northeast corner of Oklahoma, and in what is known as the Tri-State zinc and lead mining district, embracing the northeast corner of Oklahoma, the southwest corner of Missouri, and the southeast corner of Kansas. A majority of the production comes from the Oklahoma section, with Kansas second, and Missouri third.

Jan 1, 1930

By J. P. Bennett

The Bureau of Mines is investigating the acid resistance of ceramic materials to identify construction materials for emerging technology in chemical and metallurgical processes. Eight commercial ceramic materials, including two red shale, two fireclay, a silica, a silicon carbide, a carbon, and a high-alumina brick, were evaluated. Samples were exposed to 40 wt pct HN03 at 70° and 90° C and 60 wt pct HN03 at 50°, 70°, and 90° C for time periods of 110 days. Statistically significant changes in cold crushing strength were generally small or not detected, except for a strength drop in the high-alumina brick, which decreased in strength when exposed to the chosen acid concentrations at 90° C. Vol-ume and weight changes were also measured. The leach rates of Al, Ca, Fe, K, Mg, Na, Si, and Ti were monitored. Increasing temperature or a decrease in the acid concentration resulted in an increased ion leach rate. Of the conditions tested, the most severe corrosion occurred at 90° C for a 40-wt-pct-HN03 solution. The silica brick had the best overall acid-resistant properties, followed by a red shale and a fire-clay brick. The carbon and silicon carbide bricks are not recommended for service.

Jan 1, 1984

By J. W. Miller

Wyoming County had for many years supplied large quantities of coking coals to coke plants throughout the eastern United States and Canada. Up to the present most of the coal has been produced from relatively few beds, but in the future the coal will be produced from beds not previously mined in quantity. This trend is shown in the entire Winding Gulf field, of which Wyoming County is a part. This publication is one of a series of Bureau of mines reports appraising the Nation's coking coal, which y be used to determine the practicability of upgrading marginal deposits to metallurgical standards. This investigation of the preparation characteristics of Wyoming County coals is the third of the series undertaken in West Virginia.

Jan 1, 1955

By M. H. Chetrick

An important factor in the design and operation of a lignite-gasification plant is knowledge of the thermal requirements. These not only vary with different-size plants but also with the operating conditions for a plant of given capacity. Thermal data have been collected since 1945 from a commercial-scale lignite-gasification pilot plant operated by the Bureau of Mines at Grand Forks, N. Dak. The description and operation of this plant and a study of the gas-composition data have already been described in previous reports (1, 2, 3, 4, 5).2) / This investigation was made to review the thermal data taken in tests and to correlate them in terms of the fraction of undecomposed steam and the H2:CO ratio.

Jan 1, 1953

By C. H. Elder

An analysis of the geologic structure of an area of Buchanan County, Va., was made by the Bureau of Mines using imagery from an airborne AN/APQ-97 side-looking radar system to evaluate that mapping technique for delineating structural features that may cause mining problems. Side-looking airborne radar (SLAR) was found to be a useful remote sensing tool for geologic structural analysis, Fault and joint systems identified by lineaments and linear patterns in the imagery were verified by surface and in-mine observations. Little Paw Paw fault was extended 10 miles by SLAR lineament analysis. A 22-mile fault, here named the Bishop-Bradshaw Creek fault, was mapped by lineament analysis and verified by observation of the fault on the Bishop Coal Co. mine map and on offset patterns of commercial gas production along the fault and surface observation of lineament along the fault. Three major super-imposed joint sets and several fault or fractured zones were identified by SLAR lineament analysis, showing more complex structure than earlier mapping indicated. SLAR imagery accurately delineated structural features that are known to affect gas migration and accumulation and that weaken the rock forming the immediate roof to mine workings, causing mining problems and potentially hazardous environment in the mines.

Jan 1, 1974

By Louis H. Berkelhamer

"INTRODUCTION The method of differential thermal analysis suggested by Le Chatelier (1)1 in 1887 has recently emerged as an outstanding means of studying the constitution of various substances, particularly clays, soils, and miscellaneous hydrous materials (2). The literature ably discusses the applications and results obtained but has paid too little attention to specific details of construction of the apparatus. Knowledge of the apparatus is of importance to the experienced research man as is extremely useful to the novice v ho ventures into this field of analysis. Further, it is generally acknowledged that the variations in design and conditions of operation are one of the essential causes for differences in characteristic temperatures as reported by various investigators. A step forward in the elimination of such differences is the publication of the details of construction and operation of a simple and inexpensive apparatus that has proved useful at the southern Experiment station of the Bureau of Mines, where it was used in cooperation with the University of Alabama, Tuscaloosa, Ala."

Jul 1, 1944

By Edward W. Parsons

The explosive-anchored rockbolt was field tested in six mines where rock conditions varied from incompetent shale or mudstone through fairly soft sand-stone to firm sandy shales. The purpose of the testing was to document, under a wide variety of conditions and in comparison to other rockbolt anchors, the quality of the anchorage produced by the explosive-anchored bolt. In addition, the length, strength, and design of the explosive charge necessary to produce positive anchorage up to the yield strength of the weakest component of the bolt were determined. A l4-inch length beaded explosive charge was found to be suitable, in general, in relatively weak strata, and the length can be reduced in more competent strata. Of the 127 explosive?-anchored bolts tested, 118 bolts produced an evaluated anchorage in excess of 17,000 pounds. Only 4 of 43 expansion-shell bolts and 4 of 14 wedge bolts produced anchorage this good. In preliminary tests, properly coupled explosive-anchored bolts did not ignite an explosive gas mixture. Some minor phases included in the investigation were as follows: (1) effect of explosive-anchored rockbolt on surrounding rock; (2) effect of time on anchored bolts based on torque tests; (3) effect of submersion in water on rockbolt anchorage; (4) pull tests to higher loads; and (5) ignition tests.

Jan 1, 1965

By Robert E. Barieau

This report describes a method for treating pressure-volume-temperature (PVT) data obtained with a Burnett compressibility apparatus. The method makes use of a general nonlinear least-squares technique developed at the Bureau of Mines Helium Research Center. It is assumed that an adequate functional form is available for the expression of the compressibility factor as a function of either the molal density or the pressure. The functional form of the compressibility factor can be either linear or nonlinear in the parameters to be evaluated. Formulas are given for calculating variances and covariances of all parameters evaluated and for calculating the variance of calculated quantities of interest.

Jan 1, 1967

By K. Robert Dorman

This Bureau of Mines report describes laboratory and field experimentation in building mine ventilation stoppings, air-door frames, and fan bulkheads with a civil construction technique. Shotcrete is applied to a free-standing, three-dimensional wire-truss panel, which is easily cut and rapidly erected. In mines where shotcrete equipment is available, this technique should be faster and cheaper than conventional block-and-mortar or monolithic concrete construction.

Jan 1, 1980

By Donald W. Scott

Chemical thermodynamic properties for the ideal gas state from 0 to 1500 K are tabulated for all of the alkane hydrocarbons through C10. These properties are based on correlations of the extant data for the entropy, vapor heat capacity, and enthalpy of formation of individual alkanes and the equilibrium constants of alkane isomerization reactions.

Jan 1, 1974

By Jr. Smith

To investigate the effects of flow geometry on laminar flames, studies are in progress in this laboratory employing Bunsen-type burners with rectangular cross section. Interpretation of these studies requires a determination of the flow velocity at all points of the rectangular cross section for one dimensional steady laminar flow. In addition, values of the velocity gradient at the boundary for such flows are needed in the interpretation of blow-off and flash-back studies with burners of rectangular cross section. The hydrodynamical problem of steady laminar flow of a viscous fluid in channels of rectangular cross section was solved by Stokes. His results have been quoted by Love21 and by Dryden, Murnaghan, and Bateman,§/ and they have been discussed by Boussines and by Paschoud. It may be noted that the steady laminar flow of a viscous fluid in channels of rectangular cross section constitutes a hydrodynamical analogue for the problem of the torsion of an isotropic prism of rectangular cross section.

Jan 1, 1952

By V. C. Petersen

The titanium-rich end of the titanium-germanium system was investigated by x-ray and metallographic methods and verified by resistivity and dilatometer measurements. A constitution diagram is proposed. The titanium-rich portion of the phase diagram is characterized by eutectic and peritectic reactions. The eutectic composition is 19 percent germanium, and the eutectic temperature 1,360° C. The peritectic reaction occurs at 905° C. and 4 percent germanium. Germanium is soluble in alpha titanium to a maximum of 4 percent at 905° C. and in beta titanium to a maximum of 12.5 percent at 1,360° C. Both limits of solubility decrease with decreasing temperatures. Although substantial quantities of germanium are soluble in beta titanium, beta is not retained on quenching. The beta phase probably transforms to alpha by a martensitic reaction.

Jan 1, 1957

By S. A. Matthes

This Bureau of Mines report describes analysis of a copper slag for 13 elements from a single sample solution by flame atomic absorption spectroscopy. Samples are dissolved with 7 ml of an HC1-HF-HN03 (3:1.5:2) mixture in heated plastic pressure vessels. A 1.5-pct boric acid solution is added to dissolve precipitated fluorides and to reduce matrix effects that interfere with atomic absorption analysis. Preparation time is less than 1 hour per batch of 10 samples. Total analysis time is less than 6 person-hours for 130 determinations with an average relative standard deviation of 1.83 pct for the 13 elements. Simple acid standards were used for all determinations. Values obtained by this method are in excellent agreement with values obtained by slower, more costly procedures.

Jan 1, 1980