Search Documents

By H. L. Anthony, A. C. Richardson, G. D. Coe

"INTRODUCTION The Warrior View mine of the Seaboard Coal Corporation is located in Tuscaloosa County on the Warrior River about 14 miles northeast of Tuscaloosa, Ala. The Brookwood bed at this point yields a coal with fair coking qualities, and the product from neighboring mines on this bed has been used for the manufacture of blast furnace coke. The output of the Warrior View mine, however, is used exclusively for domestic and steam-raising purposes.This paper continues the series° of reports on the washability of Alabama coals which are based upon the study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal mining companies. This paper contains screen-sizing and float-and-sink tests of a representative sample of run-of-mine coal, and flakiness and crushing tests on certain sizes.Published information on the Brookwood bed is very meager. Fieldner6 gives the proximate and ultimate analyses for a number of seam samples taken from representative mines working this bed. Gandrud and Britton7 show sections of this bed taken at Searles, Ala. They also give the specific gravities of the coal, the bone, and the shale partings.Table 1 give the proximate and ultimate analyses for the 3/4 to 3/16 inch size of raw coal. Table 2 gives the sulphur content and the ash fusibility temperatures of the float-and-sink fractions for this same size. The character of the coal is very uniform throughout the range of sizes produced and, as it was not convenient to have these analyses on all sizes, this size was chosen as being representative of the coal. From the information available it is evident that the coal preparation problem is restricted to one of ash reduction.SAMPLING AT THE MINEAt the Warrior View mine the run-of-mine coal is dumped from the mine cars upon a 3-inch grizzly. The oversize is crushed in rolls set at 24 inches and joins the undersize before being elevated to the raw-coal bin ahead of the jig. The sample was caught at the point where elevates discharges into the raw-coal bin, by taking a proportional amount of the coal at 10-minute intervals over the period of a day's run, The total sample amounting to 2.7 tons was shipped to the laboratory at Tuscaloosa for the washability studies."

May 1, 1932

By Sara Jane Boles

In recent years the interest in rare-earth compounds as refractory materials has exceeded the available literature on the subject. While some basic properties, such as density and melting point, of the more readily available rare-earth compounds have been reported in the literature, relatively few papers can be found that deal comprehensively and primarily with high-temperature refractory properties and applications of rare-earth oxides, carbides, sulfides, and nitrides. Therefore, this bibliography has been pre-pared for the use of the ceramic industry as a guide for locating and utilizing the scattered and frequently fragmentary information available. The term "rare earths", as applied in the literature search for this bibliography, is understood to include the following elements: cerium, dysprosium, erbium, europium, gadolinium, holmium, lanthanum, lutetium, neodymium, praseodymium, samarium, terbium, thorium, thulium, uranium, and ytterbium. (On the periodic chart, these elements appear as numbers 57 through 60, 62 through 71, 90, and 92.) It is emphasized that many of the abstracts included are from papers in which the rare-earth compound or compounds are treated along with several other ceramic materials, are mentioned only secondarily, with primary interest placed on a more commonly used refractory material, or are used as part of a mixture of materials formed experimentally and reported on in the paper. As the better known rare-earth materials, such as the oxides of uranium, thorium, and cerium, appear more frequently in the literature, they also appear more frequently in this collection. Articles abstracted include only information on the basic properties that are of interest to the refractories investigator. References to crystal lattices and related topics are generally excluded from this publication. The temperature 1,500° C. has been set arbitrarily as the lower limit for reported data on thermal properties. However, because of the scarcity of information, some reports are included in which data are limited to those obtained at lower temperatures. Many of the articles abstracted include lists of references that will be of additional assistance in pursuing specific lines of investigation.

Jan 1, 1962

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the sixth phase of testing from mid-1996 to early 1998. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily. However, the deployed CSE SR-100s exhibited significantly higher inhaled CO2 levels than new units, as in the previous phase. This will cause higher ventilation rates in most users, which will, in turn, result in higher breathing pressures, possibly causing users to prematurely remove the apparatus. CSE Corp. has developed a noise test that can identify apparatus suffering from chemical-bed degradation causing the early CO2 breakthrough. This test was added to the inspection criteria for the SR-100. In addition, several of the MSA Portal-Packs that passed their inspection criteria were found to have KO2 dust in their mouthpieces. Further investigations by NIOSH and the Mine Safety and Health Administration confirmed these findings, which resulted in the decertification of the apparatus and their removal from service.

Jan 1, 2000

By JeffreyS. Vipperman, Daniel R. Babich, EricR. Bauer

In response to the continuing problem of noise induced hearing loss NIHL among mine workers, the National Institute for Occupational Safety and Health NIOSH has conducted numerous noise surveys in coal preparation plants. The research, consisting of worker dose monitoring, task observations, and equipment noise profiling, was completed in eight separate preparation plants. Worker dose monitoring was conducted for three shifts in most cases. Workers experiencing higher than allowable doses were task-observed for one full shift to correlate dose to noise source(s). Finally, noise levels on all floors, and in lunchrooms and control rooms, were characterized. Results indicate that only workers who routinely spend a significant portion of their shift in the plants (away from the control rooms) are susceptible to overexposure from noise. Certain pieces of equipment (screens, centrifuges, sieve bends) are the loudest primary noise sources responsible for the worker noise exposures.

This work examined the feasibility of in-mine coal preparation in two phases. Phase I included a survey of previous investigations and a preliminary analysis of the economic and technical feasibility on a selection of representative sites and degrees of cleaning. The contract was terminated at the end of Phase I. The preliminary analysis determined that in-mine preparation systems can be applied using currently available technology. The most likely mines for application will have shaft or slope access and be deeper than 500 feet. The refuse disposal systems technically feasible are (1) pneumatic placement of coarse refuse in room and pillar panels or longwall faces, (2) mechanical placement of coarse and fine fractions in room and pillar panels, and (3) hydraulic placement of fine fractions in room and pillar panels. The economic feasibility is much more dependent on the refuse disposal-system than on the preparation system. It is estimated that the capital cost of an in-mine preparation and disposal system would be $6.00 per clean ton and the operating cost would be $1.24 per clean ton for a 1 million clean ton per year mine.

Jan 1, 1982

By John C. Machisak

INJURY EXPERIENCE AND EMPLOYMENT DATA on all stone quarries and associated plants in the United States are presented in this publication for the calendar year 1959. Such related operations as the manufacture of cement and lime and rock dressing are included. Data on clay and sand and gravel operations are not included and will be found in other Bureau publications on injuries and employment. The Bureau is authorized to make requests for such data and the information voluntarily submitted by the operators contributes to the promotion of safety in the quarrying industry. Every effort has been made to make this canvass as complete as possible. Data for production workers and office employees at the quarry site are included.

Jan 1, 1963

By John C. Machisak

INJURY EXPERIENCE AND EMPLOYMENT DATA on all stone quarries and associated plants in the United States are presented in this publication for the calendar year 1959. Such related operations as the manufacture of cement and lime and rock dressing are included. Data on clay and sand and gravel operations are not included and will be found in other Bureau publications on injuries and employment. The Bureau is authorized to make requests for such data and the information voluntarily submitted by the operators contributes to the promotion of safety in the quarrying industry. Every effort has been made to make this canvass as complete as possible. Data for production workers and office employees at the quarry site are included.

Jan 1, 1963

By W. R. Hardwick

This information circular describes open-pit mining methods and practices of the Bagdad Copper Corp., Yavapai County, Ariz. It is one of a series being prepared by the Federal Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. A brief history of the Eureka district and of early developments at the [gdad] mine is given, and the are deposit is described with particular emphasis on those characteristics (physical, economic, or engineering) that affected the choice of mining methods. Prospecting, exploration, and sampling and estimating the tonnage and grade are outlined. Development of the open-pit mine is shown. Mining methods, including breaking ground, primary drilling and blasting, secondary drilling and blasting, loading, transportation, engineering, and operating control, are described. A brief summary of mining equipment is given. Percentage of extraction, production rate, mine drainage and water supply, wage, contract, and bonus systems, safety and fire prevention, and the processing plant also are described. The last section gives a breakdown of such costs as are available for publication.

Jan 1, 1959

By G. G. Morgis

In carrying out the provisions as set forth by an Act of Congress (36 Stat. 369) approved May 16, 1910, effective July 1, 1910, and the amended Act of February 25, 1913, (37 Stat. 681), the Bureau of Mines, among other activities, conducts inquiries and scientific and technologic investigations concerning mining with a view to improving health conditions and increasing safety and disseminates the general information gained by these studies. Through the medium of these publications, the causes as well as the methods that have been found most satisfactory in combating undesirable conditions are brought to the attention of the mining industry. This bulletin describes health and safety reports that have been published for the period July 1, 1955, through June 30, 1961. Technical Paper 705 issued in 1948 contains a listing of all Bureau of Mines publications dealing with health and safety in the mineral and allied industries from 1910 through 1946; Bulletin 558 contains a bibliography of such reports that were issued from January 1947 through June 1955.

Jan 1, 1962

By David A. Larson

Preliminary laboratory experiments have been conducted by the Bureau of Mines to define the influence of bit geometry on methane ignitions as a step toward establishing safer mining-machine operating parameters. The experimental system was designed to simulate the operation of a continuous mining machine, using a drum-type cutterhead of normal diameter with a narrow cross section, permitting full-diameter drum cutting tests to be run on material representative of sandstone lenses (or inclusions) in coal seams. Two conical bit types were tested at shallow depths of cut with three drum speeds. Bits that rotated in the mounting block during testing did not produce ignitions. The ignition frequency for used bits was three to four times greater than for new bits at the same kerf depth.

Jan 1, 1983

By M. A. Trevits, M. R. Thibou, A. Ozment, A. C. Smith, J. B. Walsh

The Excel No. 3 Mine is a room-and-pillar mining operation owned by MC Mining, LLC, a subsidiary of Alliance Resource Partners, LP, which produces coal from the Pond Creek Coalbed in Pike County, Kentucky. Late on December 25, 2004, a fire was discovered near the bottom of the slope and, after an unsuccessful attempt to fight the fire underground, it was decided to address the fire remotely from the surface. The mine operator developed a plan to fight the fire that called for the installation of temporary seals at the slope and mine shafts to eliminate the inflow of oxygen. In addition, the plan called for drilling and completion of vertical boreholes into select areas of the mine workings to monitor the mine atmosphere and inject nitrogen gas and gas-enhanced foam. Over the next 9 days, nitrogen gas was injected almost continuously and gas-enhanced foam was injected periodically as deemed necessary. On January 7, 2005 it was determined that the fire was successfully suppressed. This paper presents a discussion of the fire-fighting approach and an analysis of the results of the application of gas-enhanced foam technology.

By L. H. Duschak, C. N. Schuette

In the years 1850 to 1923, the United States produced 2,426,000 flasks- (73,600 metric tons) of quicksilver worth $120,500,000. California yielded 2,195,000 flasks of this total; the remainder came from Texas, Oregon, Nevada, and A.rizona. Most of this metal has been extracted from low-grade ores, those containing less than 0.5 per cent mercury or 10 pounds per ton. The finished product or " virgin metal" is made at the mine and shipped in flasks. Quicksilver is unique in being the only metal that is liquid at ordinary temperature. Because of this and other physical and chemical properties, it is perhaps more indispensable to industry than any other metal. On the other hand, the quicksilver industry of the world is of vanishing significance" when compared to the major mineral industries with respect to quantity and value of product, capital invested, or the number of men employed. The peculiar value of quicksilver is due to the fact that in some of its applications no substitute is available and in others the substitutes would be unsatisfactory or extremely expensive. Scarcely a branch of science or industry fails to make some use of mercury or its compounds. As a detonator for explosives, mercury fulminate holds first place and in safety and reliability could be replaced only by the highly expensive silver fulminate.t vThrough its use in detonators and in the metallurgy of the precious metals quicksilver is of special importance to mining. In medicine,in the manufacture of electrical apparatus, the production of pigments and antifouling paints, and the general field of experimental science quicksilver is equally indispensable.

Jan 1, 1925

By M. John Brodie

This report reviews the regulatory environment as it pertains to tailings management and disposal from mining operations, excluding coal and placer gold operations, in the state of Alaska. It is based on the EPA's staff position on an effective program to regulate mining wastes as presented in the May, 1990 Strawman II document, The unique conditions which occur in parts of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a railings disposal facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection are examined.

Jan 1, 1992

Four taconite plants were studied to establish the extent of hazard to plant personnel which exists based on long-term exposure to noise. The criteria for evaluation include the 90 dBA and 85 dBA summations of partial exposures. Data from extensive interviews were used to determine all work stations or locations which employees occupied and how much time they spent in ach location in a typical working day. Noise level measurements at every designated location were then made. By means of a computer program, these time and noise level data were us d to find the optimum noise reductions which would be required throughout each plant to meet both noise criteria. Subsequently, each plant was examined in detail so that the apparent sources of noise for each of the locations requiring noise reduction could be delineated. In tabular form, this report presents the hazardous locations for each plant, the existing noise level, the optimum noise reduction which would be required to meet the current and proposed laws, and the sources of noise which produce the existing noise level.

Jan 1, 1977

By Robert H. Lambeth

There are no identified mineral resources in the Italian Peak RARE II areas, and there are no producing or developing mines within or adjacent to the study area. Several prospects are in RARE II area M-4945, Idaho, but none were found in the area I-1945, Montana. The Viola Mine (fig. 1, no. 15) vicinity and the Heart Mountain vicinity along the west and south borders, respectively, are being prospected. There has been no recorded production from mines within the study area, but between $2.5 million and $5.0 million worth of lead, silver, and zinc were produced in the adjacent Birch Creek district - dominantly from the Viola Mine - from 1882 to 1889 (Anderson and Wagner, 1944, p. 14). The Viola and other mines in that district are possibly, on basin-margin, carbonate-hosted, lead-silver-zinc deposits stratabound within the Devonian Jefferson Formation. Previous studies have considered them to be hydrothermal, replacement orebodies. Mineral occurrences in the Heart Mountain area are possibly black-shale hosted uranium-vanadium deposits in the Mississippian-Devonian McGowan Creek Formation or perhaps the underlying Devonian Three Forks Formation. The Jefferson and McGowan Creek Formations underlie many scattered segments of the study area. The deposits and occurrence; are not sufficiently exposed to determine tonnage and grade, but sampling indicated moderate resource potential at two properties just outside the study area, the Viola Mine and the Elkhorn Group (fig. 1, no. 33). Local residents indicated there are several thousand tons of zinc-bearing resource; at the Viola line. A 23-ft (70-m) drill hole intercept near Heart Mountain et the Elkhorn Group adjacent to the stuny area contained 0.15 percent uranium oxide

Jan 1, 1983

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The ;purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of mining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENTS The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By Oliver Bowles

Sandstone, a widely distributed siliceous sedimentary rock, is the third most popular building stone in the United States. It is formed by the breaking down of preexisting rocks by weathering, subsequent segregation of the detrital quartz grains into discrete deposits by the sorting action of water or wind, and finally cementation of the quartz sand into a coherent rock. The homogeneity and resistance to weathering of the resultant sandstone make it suitable for exterior construction. Its excellent wearing properties explain its popularity for flagging and stair treads. However, quarrying and dressing methods and costs are adversely affected by the abrasiveness and hardness of sandstone especially as compared to limestone.

Jan 1, 1963

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the quantitative procedures that have been developed for the mine-specific analyses of accident/injury experience data are presented and their applications are demonstrated in a summary form through case study examples. The quantitative procedures will aid mine safety management personnel to develop focused accident prevention strategies including training, as well as to justify the investment in such proactive programs through cost-benefit analyses.

Jan 1, 1993

By William H. Schiffbauer

The Bureau of Mines has developed a passive encoder for range knobs, a device that automates the task of obtaining the range settings from devices or instruments to be input to microcomputers. It is easily constructed and installed and will not disrupt the device to which it is being attached. It consists of a custom knob and a small printed circuit board that has light-emitting diodes and magnetic reed switches attached. A ribbon cable connects it to a microcomputer. This encoder eliminates one source of human error in an automated process.

Jan 1, 1983

By G. St. J. Perrott, N. A. Tolch

"The measured strength of an explosive depends to a certain extent on which it is determined. An earlier investigation showed the relative propulsive strength of dynamites as determined in one type of apparatus, ballistic pendulum.4 The aim of this paper is to precept strength data on these same dynamites determined in another type of apparatus, the Trauzl lead block, and to compare the results with those of the ballistic pendulum. Trauzl lead block have been in use many years for the determination of thy strength of explosives, under moderate confinement.5 The common practice is to shoot 10 grams of explosive, in tinfoil wrapper,- and then to measure the volume of the cavity produced by the shot. The volume of the original borehole is deducted from the gross expansion and sometimes a correction is made for the expansion produced by the detonator. Dry sand is used for stemming the charge.It has been found that the expansion in Trauzl blocks is not strictly proportional to the charge. Naoum5 believed that for scientific accuracy the charge should undoubtedly be regulated to give the same average expansion for each sample tested, but for expansions of 200 to 400 cubic, centimeters the deviation from proportionality is not sufficient to give results appreciably in error.Neubner7 found that the proportionality curve is tangent to the charge-expansion curve at about 300 cubic centimeters expansion, provided that no deductions are made for the volume of the original borehole or the effect of the detonator; the total or gross expansion is proportional to the charge between expansions of 250 to 350 cubic centimeters without serious error."

Oct 1, 1930