Search Documents

This manual is for use by mine operating personnel and vehicle manufacturers in the selection and proper use of automatic fire protection systems for underground metal and non-metal mining vehicles. Most of the currently available systems are manually operated, dry chemical fire suppression systems. When properly designed, installed, and maintained these systems have proven to be effective both in fire suppression and in withstanding the rugged mine environment. Portable fire extinguishers and manually actuated systems have provided adequate protection for most of the reported fire incidents. However, there have also been incidents where injuries and property losses would not have occurred if the vehicle had been protected with an automatic fire protection system. The need for reliable automatic systems exists when the operator is not present, especially when the vehicle engine is running without the operator in the cab; and also in cases where the operator leaves the vehicle to fight a small fire with a portable and is then forced to abandon the vehicle because the small fire becomes uncontrollable. In the later cases manual systems on the vehicle are never actuated. Although these incidents have been relatively few in number in the past, the increasing use of mobile diesel powered equipment and the related importance of personnel safety, high costs of the mining vehicles, and high cost of down time warrant consideration of automatic fire protection systems. The fire history data and the design concept discussed in this manual were developed under the Bureau of Mines Contract H0252038 which is part of the government's mining research safety program. The purpose of the contract was to develop a low cost, reliable, prototype automatic fire control system for underground vehicles. The industry needs were determined through an extensive mine visitation program, and the prototype system was demonstrated on a vehicle in an underground mine fire test. The system developed under this contract was specifically designed for a load-haul-dump. However, the design concept is applicable to the full general class of mobile underground mining equipment.

Jan 1, 2011

Construction workers may be exposed to hazardous dust containing crystalline silica during site preparation when drilling systems are used. The National Institute for Occupational Safety and Health (NIOSH) found that drill dust could be decreased by using wet or dry dust reduction engineering controls, enclosed cabs, and implementing a dust control program.

Jan 1, 2009

By A. Wahab Khair, Nagendra P. Reddy

"This paper presents an analysis of preliminary tests on the effect of in-situ and operating parameters on fragmentation of coal using a specially designed unique automated rotary coal cutting simulator (ARCCS). In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.l cm x 15.2 cm) were first. subjected to confining pressures, equivalent to in-situ conditions. Such. blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with a camera attached to it. Furthermore, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis. The results of the preliminary tests indicated that underground coal cutting can be simulated in the laboratory and the effects of the important parameters, i.e. operating and in-situ parameters, can be studied successfully. INTRODUCTIONThe continuous-mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners, which were designed for increased productivity, have also increased the concentration of respirable dust in mines. As a result, the Federal Coal Mine Health and Safety Act of 1969 was enacted to enforce on the coal operators that the airborne respirable dust not exceed 2 mg/m3, and was intended to reduce the incidence of coal workers pneumoconiosis. This plus the other aspects of the legislation and the subsequent monitoring and enforcement by MSHA made it very imperative that the coal operators provide a relatively healthier and safer working environment for the coal miners. Since 1970, the Federal government has paid over 11.7 billion dollars to more than 470,000 miners with coal workers pneumoconiosis and their survivors (1). These regulations, coupled with the assessment of the continuing burden on miners, the mining industry and taxpayers appear to have provided an impetus for the mining .community towards comprehending the different parameters that influence dust generation and entrainment."

Jun 1, 1988

By F. G. Scott

This document is a proposed program plan for mining environmental research to be conducted by the U.S. Bureau of Mines in support of industrial oil shale mining and processing. This program plan is one of three research alternatives being considered by the Bureau, each based on a different level of anticipated funding. This report documents the high funding level program plan.

Jan 1, 1980

By F. S. Crawford

A large number of operators of various industries in the United States do not appear to realize the great returns in dollars and cents which result from intelligently directed safety work . Managers of co 1 mines , metal mines , open-pit mines , quarries , steel mills , cement mills , oil rei meries , iron works , or other industrial operations , should by all means realize the great waste resulting from accidents , in order to appreciate the necessity for a continuous accident -prevention policy . While the prevention of accidents is worth while from the humanitarian standpoint alone , it has an equally important economic side , and before our mining industrial operations will be made as safe as they should be , it is apparent that this dollars and cents viewpoint must be given full recognition in order to bring before many of the men who run the industries the great importance of this phase of industrial management . : There is a tendency upon the part of the opera or who has not given thought to the cost of accidents ( and there are many mining operators of this type) to insure his company against compensation losses and against catastrophes for which he can secure insurance , and think he has done his duty ar an executive . Even though industrial operations were not compelled to pay compensation , and even if the management were not moved by humanitarian motives to try to stop accidents , it would pay many times over to carry on accident prevention work vigorously and continuously. : In some parts of the United States , the state compensation and insurance requirements are such that the operator does not receive a reduction in his insurance rate per men employed upon having made safety installations or upon having achieved a reduction of accidents in his plant . Under such conditions the management frequently does not feel encouraged to emert much effort in bettering the accident rate . However , when the responsible officials of a company realize the much greater harm to an operation which results from doing no accident - prevention work , and the great benefit in reduced costs which usually follows effective safety work , they should be inclined to do almost everything possible to reduce accidents , regardless of considerations as to accident compensations . There are enough indirect costs resulting from accidents to wreck many types of business ; excessive accidents result in disorganization and failure , while immunity from accidents usually means a smoothly running efficient organization .

Sep 1, 1930

By R. E. Cumings

The Bureau of Mines made electrorefining tests in inert-atmosphere, molten salt cells to develop methods for the preparation of high-purity molybdenum. Seven of the electrolytes investigated were suitable for the preparation of refined metal. The electrolytes were composed of molybdenum chloride in alkali chlorides or mixtures of alkali and alkaline-earth chlorides. An electrolyte composed of potassium chloride and potassium hexachloro-molybdate was selected for a larger scale, more detailed study on the basis of its ease of preparation, its ability to retain the molybdenum salt, and the type of deposits obtained. High-purity molybdenum in the 99.99-percent-purity range was successfully prepared as dense plate up to 80 mils thick and as dendritic crystals. The temperature of electrolysis and the current density were major factors in determining whether plate or dendritic crystals of molybdenum were obtained.

Jan 1, 1966

By Sidney Katell

This study presents the economics of the hot-carbonate purification process for removing C02. It considers three variations of the process in order to meet the design specifications, which call for a feed-gas flow of 10 million standard cubic feet per hour (std.c.f.h.) with C02 inlet concentrations of 10, 20, and 30 percent and exit C02 values of 5, 2, 1, 0.5, and 0.1 percent. Inlet pressure and temperature are 350 pounds per square inch [e] (p.s.i.g.) and 300° F., respectively. Estimated capital and operating costs are shown in the following to tabulations: [ ]

Jan 1, 1960

By D. H. Carlson, J. H. Johnson

"The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios.The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory grade instruments. Concentrations of CO and C02 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for C02• EMA measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and C02 differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios."

Mar 1, 1992

By F. E. Block, Stephen D. Hill

The necessity for measuring radiation dose is encountered in studying both the beneficial and damaging effects of ionizing radiation on materials . It is also necessary to know the radiation dose absorbed by the reactants in order to evaluate the efficiency of reactions or processes that are promoted by radiation . Thus , a significant effort was made at the Albany cobalt 60 facility to investigate techniques by which the exposure radiation dose can be determined . Methods including ferrous sulfate , ceric sulfate , and methyl methacrylate chemical dosimeters , ion chamber dosimetry , and an absolute radiation calorimeter were investigated . Isodose curves were constructed for several standard source configurations using the dosimetry techniques which were investigated .

Jan 1, 1964

By V. F. Parry

[Approximately 7-1/2 million tons of subbituminous coals are mined annually in Colorado, Wyoming, and Montana, of which 50 percent probably reaches domestic consumers. The moisture of these subbituminous coals is high, averaging about 25 percent when they are mined. The coals are non-caking end stack to a variable degree when exposed to normal atmospheric conditions. They are good domestic fuels, are considered to be smokeless in most furnaces, and have been used for many years in hand-fired domestic furnaces in which the practice is to employ large lutes for efficient combustion.]

Jan 1, 1941

By B. W. Gandrud, G. D. Coe

"INTRODUCTION The Southern Experiment Station of the U.S. Bureau of Mines, cooperating with the University of Alabama and Alabama coal producers, has made a series of investigations of the washability of coal from commercially important bens of Alabama. The results of 13 investigations pertaining to the Mary Lee, Clark, Black Creek, Jefferson, Pratt, Corona, Carter Brookwood, Blue Creek, Thompson, and Woodstock beds have been published. 4/ This report, the fourteenth of the series, deals with run-of-mine coal from the Henry Ellen bed at the Acmar No. 5 mine of the Alabama Fuel & Iron Co.The Acmar mine is 1/2 mile west of Acmar, Saint Clair County, in the northern part of the Cahaba field. Present production at the mine is about 800 tons per day, all of which, accept the lump coal, is treated in jigs. The washability data were obtained by means of screen-sizing and float-and-sink tests. There are included, also, tests showing the extent of liberation of impurities by recrushing the coarser sizes of coal from the top bench and tests showing the flakiness in selected sizes.SAMPLING AT THE MINEThe Henry Ellen bed at Acmar consists of two benches separated by a shale parting. At the point of sampling the top bench was 6 feet 3 inches thick and contained a 1-inch and a 1 1/2-inch band of bone. The bottom bench was 5 feet thick and was separated from the top bench by 20 inches of shale. In taking the samples for the washability study the working face was squared up, and a representative 2-ton section was out from each bench. The shale parting was discarded, according to usual mining practice."

Nov 1, 1936

By J. J. Sammarco

Light emitting diodes (LEDs) are emerging as viable replacements for incandescent-based cap lamps used in mining. The photometric and energy characteristics of these light sources differ in important ways. The present paper describes the performance of LED and incandescent sources in cap lamps in terms of correlated color temperature, color rendering, light output, electric power, ambient temperature and airflow, and light source aging. Importantly, these characteristics can influence a miner?s ability to spot mining hazards thus impacting safety. Secondly, some of these characteristics interact with the operating life of the cap lamp?s battery power, such that differences between LED and incandescent sources can be magnified toward the end of a 10­hour battery discharge cycle. Empirically, we have determined that after 8 hours at an ambient temperature of 25 °C, the average light output of an incandescent cap lamp can decrease to about 69% of its initial value when powered by a lead-acid battery and it can decrease to about 65% of its initial value when powered by a nickel-hydride battery. An LED-based cap lamp using a constant current drive circuit can maintain about 96% of its initial value when powered by a nickel-hydride battery. Real-world tests addressing the effects of ambient temperature and airflow on the light output of an LED and incandescent cap lamp were conducted in the NIOSH Safety Research Coal Mine (SRCM). The LED cap lamp yielded a vertical average illuminance improvement of approximately 9.5% and the INC cap lamp yielded a vertical average illuminance degradation o f approximately 4%. The differences between LED and incandescent cap lamps were further quantified by the calculation of ?mesopic luminance? data that indicated for the same photopic luminance (i.e., as measured using a conventional light meter) the LED cap lamp could be up to 38 % more efficient than the incandescent cap lamp with a lead-acid battery at the end of the 10-hour driving cycle. Lastly, accelerated life tests were used to empirically determine light output depreciation as the incandescent light source age approached its useful life. There was about a 35% decrease in light output. This is quite considerable, especially given that the light output will decrease an additional 30% to 45% over the period of a 10-hour shift. The implications of the differences between LED and incandescent sources are discussed. This information is crucial in determining how visual performance could be affected for real-world conditions where batteries discharge during the work shift and as the light source ages. To date, only idealized conditions have been used for LED and incandescent cap lamp visual performance research.

Jan 1, 2008

By Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition, a revision which would supply up-to-date information on coal research and which would facilitate communication among organizations of similar interest seemed important. This compilation includes the names and activities of organizations of various types-government, university, private, and industry. The areas of investigation that each organization is engaged in are indicated in broad terms: Analysis and constitution, mining and geology, preparation, briquetting, combustion, high- and low-temperature carbonization, gasification, conversion to solid and liquid fuels, and health and safety. Publications issued by and describing the work of each organization are cited; almost all of the organizations also publish results of their investigations in the technical press. Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country.

Jan 1, 1966

By T. E. Green, E. F. Spano, W. J. Campbell

A combined ion - exchange X- ray spectrographic method was developed and evaluated for determining trace amounts of cobalt and nickel in high - purity tungsten and tungsten trioxide . The sensitivity for both cobalt and nickel is in the range from 0.2 to 0.5 μg ( 0.04 to 0.1 ppm , based on 5 gram samples ) . Accuracy at the 5 to 20 μg level is ±10 percent of the amount present . Approximately 16 hours elapsed time is required for analysis

Jan 1, 1963

By M. B. Boyer, C. H. Herty, F. A. Hartgen, G. L. Frear

"DEFINITION OF VISCOSITYViscosity has been defined as the resistance experienced by one portion of a liquid moving over another portion, such as one molecular plane moving over an adjacent plane. A measure of viscosity is the force required to keep one plane in motion at Unit velocity, the other plane being considered stationary. Figure 1 illustrates the general idea that the surface friction between two adjacent areas will be greater the larger the molecules. Therefore it may be assumed that viscosity will be increased by molecular association or agglomeration, and likewise dissociation rill decrease viscosity. According to Maxwell (1)6 the unit of viscosity, the poise, is the tangential force per square centimeter of area of either of two horizontal planes 1 centimeter apart, one of which is fixed while the other moves with unit velocity, the space between being filled with viscous liquid of unit viscosity.The need for a satisfactory apparatus and experimental procedure for the determination of viscosity of high-melting materials at temperatures corresponding to those in pig-iron and steel making has been recognized during the past few decades. The condition of the slag during the smelting and refining periods in the iron- and steel-making processes exerts an important influence on the metal product obtained, this slag condition really meaning the state of viscosity or, vice versa, fluidity, which the slag attains under certain conditions."

Jun 1, 1934

By Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition, a revision which would supply up-to-date information on coal research and which would facilitate communication among organizations of similar interest seemed important. This compilation includes the names and activities of organizations of various types-government, university, private, and industry. The areas of investigation that each organization is engaged in are indicated in broad terms: Analysis and constitution, mining and geology, preparation, briquetting, combustion, high-and low-temperature carbonization, gasification, conversion to solid and liquid fuels, and health and safety. Publications issued by and describing the work of each organization are cited; almost all of the organizations also publish results of their investigations in the technical press. Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country. Information that would improve coverage and accuracy of the next revision of the publication will be welcomed by the Bureau of Mines.

Jan 1, 1966

By D. H. Carlson

The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory-grade instruments. Concentrations of CO and CO2 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for CO2. EMA¬ measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and CO2 differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 2010

By Kim B. Shedd

The Bureau of Mines measured fiber dimensions on crocidolites (riebeckite-asbestos and magnesioriebeckite-asbestos) from the world's four crocidolite mining regions. The objective of the study was to determine whether there are measurable morphological differences between crocidolite fibers that correlate with the high reported incidence of mesothelioma in miners and mill employees in the Cape Province of South Africa and Western Australia, as compared with little or no reported incidence of this cancer in the Transvaal Province of South Africa or Bolivia. Fiber dimensions measured with the scanning transmission elec-tron microscope showed that crocidolites from Western Australia and the Cape Province have more thin fibers than crocidolites from Bolivia and the Transvaal Province.

Jan 1, 1985

By F. E. Block, Robert R. Brown, A. W. Henderson

The chlorination of Cr₂ 03 (chromic oxide ) in the presence of carbon with CC14 (carbon tetrachloride ) and COCl2 (phosgene ) chlorinating agents was investigated by employing the radioactive tracer carbon By tagging carbon mixed with Cr₂ 0з , the chlorination reaction was evaluated in terms of the competitive reaction of the elemental carbon and the carbon contained by the chlorinating agent . A unique gas - analysis train was used to separate the chlorination product gases ; CO , CO₂ , and COC12 . The C¹ activity of the gases was determined and used to calculate the reactivity of each source of carbon . Reactivities were determined for the temperature range from 600 ° to 900 ° C. The results of the investigation show that each source of carbon reacts significantly with the Cr2 03 and that the reactivity of each form of carbon depends on the reaction temperature , and each form is independent of the other . Radioisotope and gas - analysis techniques are discussed and a description of the experimental apparatus is given .

Jan 1, 1964

By J. K. Whyatt

The U.S. Bureau of Mines conducted an overcore stress measurement on the 5300 level of the Lucky Friday Mine, Mullan, ID, to investigate the stress regime around an experimental stope in a rock-burst-prone mine. The result indicated a stress field with unexpected magnitude and orientation [s 1 ?135 MPa (19,600 psi) oriented S 80° W). An unusual amount of rock-burst activity was encountered during subsequent excavation. A careful review of the overcore data suggested the overcore strain measurements were valid. Moreover, concentrated rock-burst activity suggested that the measured stress field did exist, but was localized and therefore did not represent the far-field in situ stress field.

Jan 1, 2010