Search Documents

By H. L. Riley

This report describes the methods and equipment used by the Watauga Stone Co. to drill and blast limestone in a two-level quarry, and to crush, screen, blend, and load this stone. Power requirements per ton of stone produced are reported. The personnel requirements for individual phases of the operation are tabulated in man-hours per ton of stone produced.

Jan 1, 1963

By William S. Roberts

As part of the Bureau of Mines critical and strategic minerals program in Alaska, 34 high-purity chromian spinel samples were analyzed for trace and major element geochemistry and mineralogy. The samples were analyzed by X-ray diffraction, X-ray fluorescence, and chemical techniques. Systematic differences in chemistry are evident when samples collected from the Chugach Mountains and their related extension are compared with chromian spinel samples collected from interior Alaska. Compared with the Chugach samples, the interior Alaska samples have higher average amounts of A1203, Fe203, Ti02, and NiO, have lower average amounts of FeO and Cr203, and exhibit greater dispersion in values. Considerable mineralogical variability of chromian spinel exists between and within individual Alaskan chromite-bearing ultramafic complexes. Of 34 samples analyzed, 25 samples are magnesiochromite, 5 are chromite, 3 are spinel, and 1 is hercynite. As a group the interior Alaska samples have a smaller average unit cell dimension than the Chugach group of samples. The chemical and mineralogical differences between the two groups of samples can be attributed to different genetic histories and may have implications for locating chromian spinel deposits amenable to standard beneficiating techniques.

Jan 1, 1985

By Edmund Shaw

This paper is one of a series being prepared by the United states Bureau of Mines describing mining and milling methods and costs at industrial mineral plants throughout the United states. These papers are designed to disseminate technical information regarding the methods and equipment used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized that publication of total production costs might, in many instances, cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention' of the reader? is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. P. J. Weisel, Inc., with office at La Habra and plant at Corona, Calif., is the only local company that produces sand for the Los Angeles glass factories, although silica sand for other purposes is produced in other parts of southern California and the adjacent portions of Nevada. The deposit at Corona consists of coarse sand imbedded in a whitish clay and differs greatly from the other deposits, which are fine-grained sandstone that must be crushed before it can be screened and washed. The preparation of Corona sand has to be thorough and includes grinding in tube mills, repeated washing and rinsing, removal of dust by air separation, and magnetic separation of iron and other minerals. This requires a plant with a complicated flow sheet. The first plant built did not make a. satisfactory glass sand, and many additions and changes were necessary. It is thought that the present flow sheet will remain substantially unchanged until a new plant is built. The design of a new plant would be simpler, but the process would be the same.

Jan 1, 1937

By Donald W. Ross

Petroleum oils of widely different grades have long been clarified or decolorized by contact with fuller's earths. More recently, so-called activated clays have also been used for this purpose. Still more recently ouch clays have been used in the form of nodules termed "catalytic pellets." Clays of varied appearance and from different localities possess the desired bleaching qualities, but evaluation of such clays, so useful to the oil industry, has not been simple. Previous methods of identification and evaluation have largely followed procedures of production methods and were not primarily based upon the fundamental properties of the clays. Thus) a false assumption has grown up that) bleaching clays probably have no common properties on which a-method of comparison can be based. Fuller's earths and activated clays have a large absorptive capacity for the color constituents of petroleum and its products decolorizing is accomplished by bringing the oil into intimate contact with the clay and later separating the decolorized oil from the clay with its load of absorbed coloring matter. Former practice in absorbing "color" was to use the clay as granules or In' powdered form. More recent practice is to use clay pellets that are more abrasion-resistant than the granules. The oil is either filtered through a bed of clay, percolation method, or agitated on contact with the clay, contact method. Viscous oils are decolorized at an elevated temperature, so that their viscosity is lowered to the point at which thorough contact with the clay is insured. Nonhumidifying, nonoxidizing gas, such as dry steam or dry nitrogen, is used to seal such hot oil masses from the atmosphere.

Jan 1, 1948

By Robert E. Wallhagen

The froth foam seal topping system is part of a system for remote sealing of mine passages using flyash transported pnuematically from the surface. Making the final 5 percent of the seal with a foamed-in-place fire retardant polyurethane reduces the required flyash volume by 50 percent and provides a more reliable seal. Foam components are held at the surface under proper conditions of temperature and pressure; then conveyed down the borehole through individual hoses and mixed at the bottom with a static mixer. The polyol component is pre-mixed with fluorocarbon-12 which, when released from system pressure in the mixer, boils and causes the foam to expand. Difficulties in handling this particular foam formulation are offset by a flame spread index well below the 25 level by ASTM E-162 normally required for under-ground applications. Isocyanate, polyol (TDI) and catalyst are conveyed to the downhole package by three separate lines. Five additional lines operate the valving and convey solvent so that the mixer and package lines can be flushed immediately after foaming. The eight-hose bundle is provided in segments of several lengths so that bore-hole depths can be matched. Cast-in-place plastic cylinders hold the bundle together and transfer the weight of the hose through a special quick-release clamp to the crane's wire rope. The downhole package and hose bundle are deployed using a specially designed winch and crane system capable of borehole deployment to 1500 feet.

Jan 1, 1977

Provide room-and-pillar operators with practical in- formation and guidelines concerning multiple-seam mine design to reduce ground problems associated with the interaction of adjacent working.

Jan 1, 1994

To provide a practical method to reduce hand and arm injuries during roof bolting operations.

Jan 1, 2000

By H. R. Babitzke, H. Kato, R. E. Siemens, G. Asai

The purpose of this investigation was to develop a wide variety of columbium and tantalum alloys and to determine their suitability for use at elevated temperatures . Sixty - nine columbium and tantalum alloys were investigated . For this study , columbium was alloyed with two or more of the following : nium, tungsten , vanadium , titanium, and zirconium . Tantalum was alloyed with vanadium or hafnium, or hafnium and carbon . The fabricability was determined by an arbitrary procedure . Hardness measurements , elevated - temperature tensile properties , and oxidation- resistance studies were made . Of the alloys studied , Cb - 15 Hf - 5W, Cb - 15Hf - 5W- 10Ti , Cb - 15Hf - 10W- 10Ti , Cb - 10V - 5W, Ta - 30V , and Ta - 20 to 33Hf exhibited excellent high - temperature properties . These alloys were not only easy to fabricate , but they also had good oxidation resistance and excellent high- temperature strength .

Jan 1, 1964

By J. S. Tosh

The Federal Bureau of Mines has investigated the equilibrium of the system potassium carbonate (K2C03) potassium bicarbonate (KHCO3) potassium bisulfide (KHS) carbon dioxide (C02) hydrogen sulfide (H2S) water (H20). Partial pressures of hydrogen sulfide, carbon dioxide, and water vapor were measured at 70° to 130° C. over solutions of 20-, 30-, and 40-percent-equivalent potassium carbonate containing from 20 to 3,000 grains of equivalent hydrogen sulfide per gallon of solution. This study was made to obtain equilibrium data for evaluating the feasibility of using solutions of hot potassium carbonate for removing, hydrogen sulfide from gas mixtures. The equilibrium partial pressure of hydrogen sulfide may be correlated with the ratio of the molal concentrations of the solutes (KHC03) (KHS)/ (K2CO3). The relationship is shown graphically for the 30- and 40-percent solutions. Once this ratio is determined, the partial pressure of hydrogen sulfide can be obtained from the curves. The equilibrium data show that effective removal of both carbon dioxide and hydrogen sulfide can be achieved simultaneously with hot solutions of potassium carbonate.

Jan 1, 1960

By C. A. Robotham

The following; paper describes underground mining practices of the Riverside Cement Co. of Los Angeles, Calif., in the Stanley limestone deposit at Crestmore, Riverside County, Calif. It is one of a series of papers being prepared for and published by the United States Bureau of Mines on mining methods and costs in tae various mining districts in the United States. ACKNOWLEDGMENTS Acknowledgment is made of the assistance received from E. D. Gardner, supervising engineer of the United States Bureau of Mines Experiment Station, Tucson, Ariz., in connection with the preparation of this paper and of the cooperation of John Treanor, president of the Riverside Cement Co. Valuable assistance in developing the mining methods was obtained from a study of similar practices in the copper-mining; districts of Ray and Globe-Miami, Ariz.

Jan 1, 1934

By A. Gene Collins

This report discusses some of the chemistry and geochemistry of cesium and rubidium. Knowledge of the cesium and rubidium content of oilfield waters aids in resolving the origin of waters and petroleum, exploring for petroleum and other valuable minerals, discovering water pollution sources, and augmenting the knowledge of geologic formations. The methods described in this report permit the detection of less than 0.01 mg/l of cesium and/or rubidium in a complex oilfield brine or water. Solvents possessing high-dielectric constants were evaluated for their ability to extract cesium and rubidium tetraphenylboron from oilfield waters and for their flame emission characteristics. Nitroethane was selected and used for the extraction and flame spectrophotometric determinations because it gave the highest sensitivity. Cesium 137 and rubidium 86 were used to determine the extraction efficiencies, which were about 87 percent and 58 percent respectively using a single 10 ml nitroethane extraction from a distilled water matrix. The standard deviation of the determination was 0.0008 mg for cesium and 0.0007 mg for rubidium in the 0.01 mg range.

Jan 1, 1965

By Keith D. Rosbury

The basic objective of this project was to determine the cost-effectiveness of dust control used on unpaved mine haul roads. Field testing was conducted at three surface coal mines (two in Wyoming, one in southern Illinois) for a total of 20 weeks. The highest control efficiency measured for a chemical dust suppressant, 82 percent, was for calcium chloride two weeks after application. Generally, however, the control efficiencies hovered in the 40 to 60 per-cent range over the first two weeks since application, and then decreased with time. After the fifth week, the limited number of data points suggest a control efficiency of less than 20 percent. Composite watering data were fairly uniform. Watering once per hour resulted in a TSP control efficiency of approximately 40 percent. Doubling that application rate increased the control effectiveness by about 15 percent to 55 percent. Chemical dust suppressants (primarily salts and lignons) can be shown to be more cost-effective than watering under some conditions. Delta summaries and the analysis of data are contained in Volume I. Volume II contains basic data.

Jan 1, 1983

Although the technology involved in removing material from below the earth's surface has a long history, communication systems in underground workings are relatively new to the industry. Communication equipment did not begin appearing in underground mines until the early 1900's. Figure 1-1 shows a miner using a Western Electric standard telephone set for underground mines in 1913. These early phones were essentially the same as those used aboveground, except that they were enclosed in cast-iron boxes as protection against moisture, acid fumes, and gases.

Jan 1, 1984

By K. C. Dean

During the investigations of the occurrence of manganese in the Western United States, a Bureau of Mines examining engineer collected samples frame two properties in Beaver County, Utah. As the ores were too low in grade to be acceptable by manufacturers of ferromanganese, beneficiation studies were made to determine the amenability of the ores to concentration. The Steelville property is about 37 miles southwest of Frisco, Utah. The deposit is an example of manganese occurring as a replacement of limestone in a bedded vein or as layers in limestone associated with shale and rock decomposition products. The Susie Q deposit, about 33 miles southwest of Milford, Utah, is also a tabular replacement deposit in limestone, apparently of limited extent. Test work was done on representative samples of 2-ton lots obtained by the examining 'engineer from each of the properties mentioned.

Jan 1, 1951

Develop an easy-to-use, reliable, resin-grouted cable support system capable of being installed as primary and secondary roof support in coal mines.

Jan 1, 1994

By Robert L. Montgomery

Heats of solution of samarium (III) oxide and chloride in hydrochloric acid and of samarium (III) oxide, sulfate, and hydrated sulfate in sulfuric acid were measured. The heats of solution of this hygroscopic oxide are larger than those from the literature, probably because of more complete removal of water in the present study. From the literature value for the heat of combustion of samarium, the heats of formation of samarium (III) chloride and sulfate are -244.18 ± 0.41 and -928.5 ± 1.6 kcal./mole, respectively. The heat of hydration of the sulfate is -34.7 ± 1.0 kcal./mole. The heats of formation of other samarium com-pounds have been recalculated, using the new data.

Jan 1, 1959

By Berger

A detailed description is given of radio apparatus for controlling a coincidence outfit for relative gravity measurements. This is probably of little interest, since many types of apparatus could be used. The general method employed is the interesting thing about this paper. As long ago as 1883 von Sterneck made a proposal to control two coincidence boxes with the, seine, clock, and many persons have suggested the use of radio for this purpose. In accomplishing this it would appear to the reviewer that this method is probably inferior to that used by the Marland Oil Co., but Berger and Brückner must be given the credit for important advances in the coincidence method. In their apparatus a clock at a central station actuates a relay, which operates a short-wave transmitter (40 m.). At the receiving station the amplification is accomplished at low frequencies... The signal operates a relay which moves a slitted screen in a coincidence apparatus. This screen has been improved considerably, to decrease the mean error in observing a coincidence. As usual, a telescope is used to observe the flashes of light. It has a scale in its focal plane and positions of successive flashes are easily read off and recorded by a second observer. This makes possible' a: higher accuracy in determining the exact instant at which coincidence would have occurred at the zero point on this scale. This method obviously depends on the constance of the mechanical and electrical lag inn both sending and receiving apparatus, and may be adversely criticized from this standpoint. -- A. E. Ruark.

Jan 1, 1929

By F. E. Brantley

Blister copper was successfully deoxidized with any of a variety of reducing gases; lancing techniques or a vertical-column furnace were used to contact the copper and gases. Of the gases tested, butane, when used to lance molten copper at about 1,200° C, reaction temperature, was slightly more effective than propane, natural gas, carbon monoxide, or reformed gas for deoxidizing copper from about 1.0 to less than 0.1 percent oxygen content, Laboratory-scale tests revealed that the vertical furnace, composed of a heated column packed with silicon carbide chips or hollow carbon cylinders, was significantly faster and more efficient than the lancing technique for deoxidizing molten copper with any of the gases tested. Comparison of the gaseous-reduction method with the conventional poling method suggests that the gaseous method has important technical and economic advantages for deoxidizing blister copper to any readily controlled amount of residual oxygen content.

Jan 1, 1962

By B. J. Scheiner

Oxidation procedures based on the chlorine-hypochlorite system were investigated for improving gold recovery from carbonaceous gold ores. The oxidation pretreatment prior to cyanidation was accomplished by (1) addition of sodium hypochlorite to ore pulp, (2) by addition of chlorine to ore pulp, and (3) by generation of hypochlorite in situ by electrolysis of a brine solution used to pulp the ore. Gold extraction of 90 pct was achieved by cyanidation of carbonaceous ore that had been pretreated with 20 Ib per ton sodium hypochlorite at 50° C for 4 hours. Similarly, pretreatment of the ore pulp with 35 1b chlorine per ton at 24° to 30° C and 15 hours reaction time resulted in 89-pct gold extraction by subsequent cyanidation. Concomitant studies showed that electrolyzing the pulp prepared with a brine solution was equally as effective as electrolyzing hypochlorite and chlorine for oxidizing carbonaceous ore constituents that are deleterious to cyanidation. Gold extraction of 90 pct was obtained by electrolysis when 275 lb of are was treated at 200 amp for 7 hours in an 8-to 10-pct salt solution. Power consumption was in the range of 60 kwhr per ton.

Jan 1, 1972

By H. H. Schrenk, L. B. Berger, Robert L. Beatty

"INTRODUCTION Toxic oxides of nitrogen 5/ are formed or liberated in many industrial process and may constitute a definite hazard to the health of persons exposed to the atmospheres thus produced. Oxides of nitrogen occur in the gases involved in the use of explosives, in the gasoline products of welding operations in the exhaust of internal-combustion engines, in the vicinity of electrical discharges, in the combustion of nitrated materials, and in chemical process involving nitration or the use of nitric acid, Itis evident that oxides of nitrogen may constitute an occupational hazard in many industries, and therefore it is important that those concerned with the control of such hazards be equipped with a technique suitable for the determinations of oxides of nitrogen in the concentrations of,hygienic significance."

Feb 1, 1943