Search Documents

By Terry G. Montgomery, Eric S. Weiss, John E. Going, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike I m3 chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.

By W. H. Somerton

The basic objective of this project was to determine the permeability of coal fracture systems as a function of effective stress. The detailed steps in accomplishing this objective are given in Article I of the contract under which the work was conducted as follows: Sec. 1.1 The objective shall be to determine the permeability of the coal fracture system as a function of effective stress. At least three bituminous coals shall be studied and at least five samples of each coal shall be tested. The sample size shall be as large as possible to be representative of coal found in the seam; a minimum of four inches is preferred.

Jan 1, 1974

By Anthony J. Miscoe, William M. McKewan, Richard C. Wang

The behavior of wire ropes used in hoisting is not well understood. In an effort to improve this understanding, the structure of round-strand wire ropes was analyzed. This report provides a generalized mathematical model that completely describes the geometry of the wires. It consists of two sets of vector equations and is valid for any round-strand wire rope. One set of equations is used to trace the paths of wires that have the form of a single helix; the other is used for the paths of double helical wires. The specific model for a 33-mm 6×19 Seale, independent wire rope core (IWRC), right regular lay wire rope was presented as an example. The paths and the geometric properties of the wires, which include the path length per lay of strand, the curvature, and the torsion, were determined from this model. The effects of strain deformation were analyzed, resulting in a system of equations for determining the structural parameters of the deformed rope. In future work, the model could be used to analyze wire ropes of different constructions so that a more scientifically based understanding of rope behavior can be established.

Jan 9, 1998

By J. V. Batty

Radioisotopes of selenium (se78) and tellurium (Te123) were successfully employed by the Bureau of Mines as tracers in metallurgical research directed to developing improved methods for volatilizing these elements from low-tenor raw materials. Prior research, guided and controlled by conventional analytical methods, was seriously hampered by inconsistent selenium and tellurium analyses, by the slowness of the conventional chemical methods, and by the poor accountability of these volatile elements in test products. Methods were devised and evaluated for admixing the radioactive tracer with typical raw materials and then following the deportment of the selenium and tellurium by radiometric methods with occasional chemical analysis checks. These techniques were found unusually effective in (1) quantifying the completeness and the rate of volatilization of selenium and tellurium while heating the raw materials at different rates to different temperatures and (2) accurately tracing and quantifying the distribution of minute amounts of these volatile elements in the several products made by high-temperature treatment and in the several units comprising the experimental equipment.

Jan 1, 1962

By Phillip R. Moyle

A cobalt/manganese occurrence in Clark County, Nevada was the subject of a site-specific mineral investigation by the U.S. Bureau of Mines in 1988-90. The study site is in the northern part of the Million Hills (wilderness) study area which is administered by the Bureau of Land Management. Field work during a period of one week consisted of geological mapping and sampling of workings and outcrops, and geochemical and geophysical surveys conducted on four transects totalling 7,600 ft. Although the concentrations of cobalt (0.1 to 0.5 percent) detected in samples from the fissure zones are within the range of grades associated with world-class economic deposits, the volume of material enriched in cobalt at the study site is insufficient to warrant consideration as a potential resource. Concentrations of manganese, nickel, copper, lead, zinc, barium, and thallium, although anomalous, are too low for economic consideration. At the study site, workings consist of three trenches and nine pits. The exploration history is unknown, and no production is reported.

Jan 1, 1990

By P. A. Croce

A total of 17 mine gallery fire tests (23 including sub-tests) were completed during this report period (10/1/76 - 11/30/77), directed at identifying a hazardous timber-set fuel-loading in a mine passageway that is otherwise free of combustibles. Results of these initial tests show that the capability of a particular fuel loading for propagating a fire is dependent upon the imposed ventilation air velocity and the ignition intensity, although this dependency needs to be better defined. It is also apparent that care must be taken when relating gallery test fire behavior to actual mine fire behavior, because of the restrictive length of the gallery. Present data indicate that some modification to the instrumentation scheme may be advantageous before proceeding with future tests.

Jan 1, 1978

By Thomas J. Peters

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 7,000 acres of the 9,240-acre Little Blitzen Gorge Wilderness Study Area in Harney County, OR, to evaluate its mineral resources. The study area is dominated by a 1,500-ft-deep canyon that was carved by Pleistocene glaciers in gently westward-dipping homoclinal flows of Miocene Steens Basalt. The Bureau reviewed pertinent literature and county mining records During the field investigations, 18 rock samples were collected from basalt dikes, breccia, fractured or porphyritic flows, and 20 alluvial samples from gravel accumulations. Mercury anomalies from sampling by the Oregon Department of Geology and Mineral Industries could not be verified. The mercury might have originated -From the Pike Creek Formation, a known mercury-producing unit that may extend into the study area beneath the Steens Basalt. Any epithermal deposit at depth would be expensive to explore and develop.

Jan 1, 1986

By Michael L. Boninger, Erik J. Wolf, Rory A. Cooper

Although wheelchair users are regularly subjected to whole-body vibrations little research has been conducted to assess these vibrations or attempt to reduce them [2,3,5]. Most of the wheelchair and whole-body vibration research done to this point has been conducted on manual wheelchairs. Van Sickle et al showed that manual wheelchair propulsion over a simulated road course produces vibration loads that exceed the ISO 2631-1 standards for the fatigue-decreased proficiency boundary at the seat of the wheelchair as well as the head of the user [6]. In a study by Boninger et al [1], 66% of wheelchair users reported neck pain since acquiring their wheelchair. One of the key reasons believed to be the cause of pain, was the exposure to whole-body vibration. Kwarciak et al [4] and Wolf et al [7] performed similar studies using two methods of analysis to evaluate vibrations on suspension and non-suspension wheelchairs while descending curbs of varying heights. Both studies revealed no significant difference in the abilities of the wheelchairs to reduce the amounts of vibrations transferred to the wheelchair user. Although the efforts of wheelchair companies to reduce the amounts of whole-body vibration transmitted to wheelchair users through the addition of suspension systems is encouraging, the technology is not yet ideal. Additionally, the research to date has focused on manual wheelchairs exclusively, while little attention has been shown to powered wheelchairs. Methods This study includes the use of two suspension electric powered wheelchairs: The Quickie S-626 and the Invacare 3G Torque SP Storm Series. Each subject tested all of the configurations of the suspension wheelchairs. These included the Invacare with suspension, the Quickie with suspension set to three settings (most stiff, least stiff, and 50% stiffness), and both wheelchairs with solid inserts to act as non-suspension wheelchairs. Sixteen able bodied subjects have been recruited for this study so far. In each of the configurations of the wheelchairs, the subjects traversed an Activities of Daily Living (ADL) course. Vibrations were collected from a tri-axial accelerometer attached to a seat plate beneath the cushion during driving over the activities course. A mixed model ANOVA was used to determine if there were differences between suspensions based on Vibration Dose Value (VDV). Results Statistical analyses of the VDV data revealed significant differences between the six different suspensions over each of the obstacles in the activities of daily living course. Post-hoc analyses revealed that for each of the obstacles, significant differences existed between the Invacare suspension and the Invacare solid insert. For the Quickie power wheelchair the solid insert setting was not significantly different from the most-stiff setting for each of the obstacles

Jan 6, 2006

Assess the technical feasibility of mining small and/or deeply buried frozen placer deposits from the surface through boreholes.

Jan 1, 1997

By Terry J. Close

A mineral resource survey of the 236-mil (611-km2) Hyalite-Porcupine-Buffalo Horn wilderness study area (RARE 11 Areas No. 1-155 G, Gallatin Divide; and H, Hyalite) between the Gallatin and Yellowstone rivers in Montana, indicates there are phosphate rock and petrified wood resources (fig. 1). The area also has some potential for oil, gas, and geothermal resources. Stone and alluvium are abundant but appear to have little potential for development because other sources are available nearer to markets.

Jan 1, 1981

By Edward M. Kawenski

Float dust deposits in return airways in bituminous coal and lignite mines present a special explosion hazard. Research is in progress at the Bureau of Mines experimental coal mine to evaluate the degree of the hazard and to develop measures for preventing dissemination of dust into the ventilating air current. To determine the extent of this hazard prevailing in operating coal mines, 711 dust samples were collected in 50 mines located in the major coal fields of the United States. The mean quantity of coal and the incombustible content of the dust in the samples were determined. The term "float dust" is used to designate particles smaller than 74 microns in diameter (particles passing a No. 200 sieve) which have settled from the air current. Dust usually found in roadways and in working places is coarser than float dust, and is termed "coarse dust" (particles passing a No. 20 sieve). Variations in amount and incombustible content of coarse dust in a midwestern mine were studied previously.5

Jan 1, 1963

By Walter W. Kaufman

This report summarizes a study conducted to determine the state of the art of various rock removal systems and their capabilities. The objective of the study was to determine if currently manufactured equipment can adequately accomplish rock removal in surface mine reclamation applications. Evaluations of state reclamation regulations, with regard to topsoil rock content, were made to determine the rock removal requirements. The major categories of equipment studied are rock pickers and rock rakes. The impact of rock removal implementation on the reclamation operations is discussed in detail.

Jan 1, 1979

By Michael E. Meadows

The results of tests to determine the .regional applicability of four synthetic unit hydrograph models are presented. The SCS curvilinear (Haan), SCS single triangle, Williams and TVA double triangle unit hydrograph models were tested on 271 events from 38 USDA experimental watersheds in 14 physiographic provinces. Though inconclusive due to the limited number of events analyzed, the results indicated a regional tendency for each model, with the SCS curvilinear unit hydrograph method generally performing best overall. It outperformed the SCS single triangle by predicting better shape; they differed less than 2 percent in time of peak and peak rate predictions. The Williams model performed well at Oxford, Mississippi and Coshocton, Ohio, which suggests it may be applicable to surface mined lands within the Northern and Central Appalachian Plateau and Texas coal producing regions. The TVA model is applicable to the Appalachian Plateau, specifically the Cumberland Plateau. A second test using only the SCS curvilinear unit hydrograph on 11 small watersheds and 50 events was conducted to investigate the effect of the excesss rainfall pattern on simulation results. A Green and Ampt infiltration model was coupled with the SCS unit hydrograph model to determine if peak rate and timing errors noted in the regional test could be minimized with an alternate to the SCS curve number model for determining infiltration losses. The results confirm the curve number model is the better approach to determining the excess rainfall pattern for unit hydrograph simulation.

Jan 1, 1983

By John C. LaScola

The Bureau of Mines investigated coal storage silos to determine how gassy coal must be for methane accumulations in a silo to become hazardous and where such accumulations are likely to occur. Methane concentrations were measured in the open space above the stored coal pile, in the pile, and in the reclaiming area. No methane layering was found in closed-top silos. Reclaiming areas were as gassy as the top part of the silos. Coal samples were collected from the conveyors entering the silos in order to assess the gassiness of the coal. No simple correlation was found between the gassiness of the coal stored and the measured methane concentrations. However, at mines where the average 24-hour gas emission from the conveyor belt samples was 14 ft3/ton or more, fans or open tops were used. It appears that a large fraction of the methane released during storage remains in the void space between the coal particles.

Jan 1, 1980

By Michael Mancuso

This report summarizes the problems of topsail handling as related to present requirements of law and current equipment availability. The most prevalent topsoiling systems are reviewed along with a listing of advantages/disadvantages and best features of each system. Seven mining regions are included, along with an analysis of prevailing land use, types of soils and attendant physical, chemical am biological characteristics. There are several probable areas of future research "lined which can benefit mining, minimize the social impact of mined lands and speed the return of mined lands to more productive long-term use.

Jan 1, 1981

The combined production value of natural abrasives, which consist of tripoli, special silica stone, garnet, and emery, decreased in 1985. Shipments of processed tripoli increased slightly in quantity but decreased 6% in value, Production of garnet, an abundant iron-aluminum silicate, increased 24% in quantity and 20% in value. There was an 11% increase in the quantity and a 7% increase in the value of refined garnet shipped when compared with 1984 shipments, a new record high. Production of crude special silica stone decreased 10% in quantity and 14% in value, and shipments of finished special silica stone products decreased 85% in quantity and 68% in value. Both the quantity and value of special silica stone finished products sold or used were the lowest since 1981. Production of emery, an impure aluminum oxide, decreased 56% in quantity and 61 % in value of product mined and shipped. [ ]

Jan 1, 1987

By Lu Li, Sara E. Wilson

Occupational exposure to whole body vibration has long been associated with increased incidence of low back pain and low back injuries1. A number of studies have investigated transmissibility of seat pan vibration 5, 6. While transmissibility has been well researched, the mechanism by which vibration may induce injury has not been thoroughly studied. Winter et al. identified increased reflex response delay after vibration exposure and speculated that muscular fatigue may be the cause of this increase9. However, a mechanism has yet to be demonstrated completely. A potential mechanism that may explain the increased risk is neuromotor habituation. Muscle spindle organs have been shown in the extremities to be sensitive to muscle and tendon vibration. Rapid length changes in muscle have been shown to result in kinesthetic illusions as the regular firing of the muscle spindles is interpreted as muscle lengthening4, 7. These illusions have also been demonstrated in the paraspinal musculature2. With removal of vibration, research in the extremities has demonstrated increased positioning errors, probably due to neuromotor habituation8. In this research, it has been hypothesized that neuromotor habituation after exposure to occupational vibration will increase positioning errors. It is further hypothesized that these errors can be shown to be linked to increased reflex response time. Such increased reflex response time could, in turn, decrease spinal stability and increase low back injury risk. Methods Both positioning error and sudden load response were measured before and after exposure to 20 minutes of 5 Hz, 0.223 m/s2 RMS seat pan vibration. Subjects were asked to sit on an unpadded seat without a backrest. Throughout the whole body vibration period, subjects were instructed to put their hands on a stable hand rest and feet on an adjustable stable footrest. The subjects were instructed to assume a comfortable and relax sitting posture for the duration of the exposure. Positioning error was measured using an active-active reposition sense protocol. Electromagnetic markers (Motionstar, Ascension Tech, Burlington, VT) were used to track trunk motion. With markers attached to the skin at the T10 vertebra, the S1 vertebra and manubrium, trunk flexion (the angle from vertical of the line connecting T10 and S1) and lumbar curvature (the difference in inclination of the T10 and S1 markers) were tracked. In the reposition sense protocol, subjects were asked to maintain an upright trunk flexion and to rotate their pelvis and lumbar curvature to assume a target lumbar curvature. In the protocol subjects completed training trials, where they were asked to match their lumbar curvature using a visual display, and assessment trials, where they were asked to reproduce the lumbar curvature from memory. After two initial training trials, training trials and assessment trials were alternated for a total of 3 assessment trials. Reposition error was defined as the absolute difference between the target lumbar curvature and the lumbar curvature the subject assumed during the assessment trials.

Jan 6, 2006

By Corate L. Brierley

Low-grade porphyry copper ores containing chalcopyrite as the primary mineral was leached by two strains of acidophilic, thermophilic microbes belonging to the genus Sulfolobus. Leach tests were conducted in glass columns heated to 60-70° C. Pinto Valley and San Manuel ores sized to -1/2 inch + 50 mesh were effectively leached by the thermophilic organisms, but pinto Valley and Cyprus Bagdad ores sized to -2 inch + 1/2 inch resisted leaching. Aeration did not contribute measurably to bacterial copper extraction, since two columns, one inoculated and one sterilized, having a rest/ leach cycle without recurrent aeration exhibited copper extraction patterns similar to those of the aerated columns. Distilled water can be substituted for 9K medium without diminishing copper extraction. Decreasing the pH of the leachate to about 1.8 enhanced the extraction of copper from pinto Valley ore with the thermophilic microbes. Thiobacillus ferrooxidans was found to be relatively ineffective at copper extraction from pinto Valley ore. Of eleven solvent extraction reagents tested, Adogen 364 and Warsol at concentrations of 0.1% and 0.012 were inhibitory to oxygen uptake by the two Sulfolobus strains. Di-2-ethyhexyl phosphoric acid at concentrations of 0.1%, 0.01% and 0.001% were totally inhibitory to the respiration of both organisms.

Jan 1, 1979

By Robert F. Randolph

Real-world levels of attenuation from hearing protection devices are usually much lower than the rated values obtained under near-ideal circumstances. The shortfall is even more extreme for earplugs than it is for earmuffs, primarily because of the complicated process of fitting the plugs within the ear canal. This study examines the use of a commercially-available lubricant for hearing aids to determine whether it would facilitate improved fit and attenuation for earplugs. In this experiment, ten participants inserted earplugs with and without using the lubricant. Average attenuation was assessed with the Real-Ear-Attenuation-at-Threshold (REAT) technique, and showed over 5 dB improvement when the lubricant was used. Participants obtained an 85% mastery rate using the lubricant versus a 50% mastery rate without. These results indicate several possible applications for improved earplug performance in real-world settings where hazardous noise is unavoidable and effective hearing protection is necessary.

Jan 1, 2008

By Edward M. Kawenski

Float dust deposits in return airways in bituminous coal and lignite mines present a special explosion hazard. Research is in progress at the Bureau of Mines experimental coal mine to evaluate the degree of the hazard and to develop measures for preventing dissemination of dust into the ventilating air current. To determine the extent of this hazard prevailing in operating coal mines, 711 dust samples were collected in 50 mines located in the major coal fields of the United States. The mean quantity of coal and the incombustible content of the dust in the samples were determined. The term "float dust" is used to designate particles smaller than 74 microns in diameter (particles passing a No. 200 sieve) which have settled from the air current. Dust usually found in roadways and in working places is coarser than float dust, and is termed "coarse dust" (particles passing a No. 20 sieve). Variations in amount and incombustible content of coarse dust in a midwestern mine were studied previously.

Jan 1, 1963