Search Documents

By Donald O. Capstick

A mineral survey of the approximately 144,000-acre Borah Peak study area was conducted by the U.S. Bureau of Mines in 1985 at the request of the U.S. Forest Service. The area studied included the Borah Peak RARE II roadless areas (No. 14210, 119,864 acres of land recommended for wilderness designation; and No. X4210, 18,440 acres of land recommended as non-wilderness) and other contiguous Forest Service administered land. The study area is in Challis National Forest in southeast Idaho about 30 miles south-southeast of Challis, ID. Burnt Creek, a conterminous study area to the northeast, on lands administered by the U.S. Bureau of Land Managment, was examined concurrently. Dolomite and limestone inferred reserve bases exceed 1 billion tons each within the Borah Peak study area. The material is widespread and of high quality. Extensive sampling and more detailed mapping are required to better define the resources; however, ample dolomite and limestone occur nearby, outside the study area. Dolomite is the main constituent of several geologic formations within the study area. Sample analyses indicate that the more than 1,000-ft-thick Jefferson Formation dolomite is the most pure and is equivalent to material being mined at a dolomite-to-magnesium processing plant near Addy, WA. Analyses from limestone-bearing formations underlying much of the study area indicate that large quantities of the limestone may be suitable for a variety of uses.

Jan 1, 1987

By George A. Savanick

The objective of this research is to develop a method for measuring the tensile strength at the interface between minerals in rock. These measurements reflect the strength of the attractive forces operating at crystalline interfaces in rock. Since these forces act in opposition to the forces set up in various rock fragmentation processes, measuring their strength may help in designing more efficient methods of rock fragmentation. The method developed for measuring the strength of intergranular adhesion in rock involves separating a bicrystal from the rock and determining the tensile strength at its solid-solid interface. This technique has been successfully applied to the study of quartz-feldspar interfaces separated from massive pegmatites, graphic granite, and the Rockville granite, yielding average tensile strengths of 5.86, 8.62, and 10.65 meganewtons per meter squared (MN/m2) (850, 1,250, and 1,524 psi, respectively). The data this technique provides indicate that the members of these bicrystals are strongly adherent. Examirtation of bicrystals broken at the crystalline interfaces indicates that the bonds responsible for this adhesion operate over only a portion of the interfacial area. This work conclusively demonstrates that tensile strength tests can be conducted on small selected areas; for example, grain boundaries in rock. The small-scale zones of strength or weakness determined in this way can be related to the overall strength of the rock.

Jan 1, 1972

1.1 DEVELOPMENT OF INDUCTANCE MATRICES The basic building block in this analytical work is the development of an equivalent circuit. The equivalent circuit for the cable depends on all of the distributed parameters of the cable although the series inductance and resistance are of primary importance. The cable resistances are generally available from handbooks or from cable manufacturers. On the other hand, the cable inductances are not usually available either from handbooks or from the manufacturer's published data. Thus, it is useful to summarize the derivation of the origin of the inductance matrix from basic principles. 1.1.1 Flux Around a Cylindrical Conductor The flux pattern around a cylindrical current carrying conductor can be found by using symmetry in conjunction with Ampere's Law. From symmetry it is clear that the flux lines which always close on themselves must be concentric circles. Thus, from symmetry alone one can get a qualitative picture of the magnetic field. This is shown in Fig. 1.1 where the inner circle represents the solid round conductor and the outer circle represents a flux line. The quantitative picture will now be developed using Ampere's Law.

Jan 1, 1973

By Loren R. Anderson

A probabilistic slope stability computer model was developed at Utah State University and independently evaluated by CH2M Hill Consulting Engineers as a design and analysis tool. Volume I of this report describes the model and Volumes III and IV are users manuals for the computer programs. This volume (Volume II) constitutes the report by the CH2M Hill. It includes a description of a field investigation and stability analysis of an existing tailings dam. Based on the results of the analysis, the tailings dam was evaluated for redesign using probabilistic considerations. Conclusions are made regarding the usefulness of the model as a design tool.

Jan 1, 1982

By J. F. Neill, O&apos

The manganiferous schists occurring in the vicinity of Kings Mountain, North and South Carolina, suggest significant tonnages of potential submarginal ores. Although some reconnaissance work in connection with these deposits has been reported, no recent information has been published. Evaluation of the schists as a possible domestic manganese resource has not always adequately considered the fact that the manganese content occurs quantitatively both as oxide and as the silicate, spessartite. The Bureau of Mines investigation herein reported includes preliminary studies to indicate the extent of manganese oxide mineralization and to deter-mine the amenability of the material to sulfur dioxide leaching. The field reconnaissance studies suggest a resource containing in one area an average of 6.4 percent manganese as oxide. The procurement of depth information was beyond the scope of the investigation.

Jan 1, 1962

By L. D. Johnson

On a project which is to develop a system to suppress coal dust explosions, a facility has been built and several devices tested. The facility is a 317-foot, 4.5-foot diameter shock tube and to date 53 tests have been carried out with methane-air and methane/coal dust-air as the explosive mixtures. Suppression of slowly propagating (up to 300 ft/sec) flame fronts has been successfully carried out on two tests using the dry chemical extinguishing agent Purple K. Delivery of the material directly into the flame front Seems to be required if effective suppression is to be accomplished.

Jan 1, 1972

By Elmer E. Buban

A lightweight compressed oxygen rescue breathing apparatus (RBA) for rescue and recovery missions has been developed by Mine Safety Appliances Company under contract to the Bureau of Mines. The apparatus is a positive pressure, closed circuit system of 4 hours duration. The weight of the complete apparatus, including an optional cooler, is slightly over 30 pounds. Weight reduction over currently available RBAs is achieved through the use of lithium hydroxide for scrubbing C02 in place of conventional chemicals and the use of a composite glass fiber/ aluminum shell cylinder for oxygen storage in place of steel cylinders. Positive pressure is maintained in the breathing circuit at all times by applying a constant spring force to the breathing bag. The harness has been designed to reduce the work of the wearer by redistributing the weight of the apparatus to the wearer's hips.

Jan 1, 1981

By Lawrence H. Roth

Past failures of coal refuse embankments have resulted in more intensified efforts in inspections of coal refuse sites. Inspections, however, are mainly qualitative and time consuming. In August 1975 CH2M HILL was awarded a contract to identify, develop, and test a rapid system for monitoring coal refuse embankments to aid in inspections. The rapid monitoring system developed uses convergent and vertical photography from conventional fixed-wing aircraft. The system was tested on an active landslide and on two coal refuse facilities using both black and white and color infrared film. Field tests showed the system was capable of accurate measurement while providing qualitative data through photointerpretation. The accuracy of the system allows it to be used to monitor coal refuse embankments, tailings dams, major earth dams, and natural slopes. Bibliographies of literature reviews in the area of past coal refuse embankment failures, monitoring instruments and methods, and photogrammetry are included.

Jan 1, 1977

During the initial portion of the contract several alternative designs were considered, as set out step by step in the monthly reports. The conclusions reached during this period were - to use on INTERDATA Model 70 as the system minicomputer - to drop the idea of multiplexing and digitizing the inclinometer outputs downhole due to the greater complexity and cost that that alternative would imply - to use a multitasking software monitor to enable synchronization of the several tasks that the system would have to perform simultaneously - to use a common controller for all I/0 devices except those which were available off the shelf from Interdata - to use a sheave counter to meter off equal increments of probe travel, but to supplement this information with the use of an encoder on the winch drum in order to be able to measure total probe travel unambiguously. - to place all I10 device interfaces in a bin connected to the common controller. During this period considerable attention was dedicated to the design of the mechanical components contemplated it the original contract. Of these, only those required for vertical probe was complete at the time that it was decided to forego the mechanical subsystem and concentrate on developing the necessary electronics and software to interface with the probes being developed by the Bureau of Mines.

Jan 1, 2012

By A. Salmoni, E. K. Gillin, T. Eger, A. Cann, P. Vi, M. Hunt

Kittusamy (Kittusamy & Buchholz, 2004) state that there have been few studies conducted to assess exposure to whole-body vibration (WBV) in the construction industry. They suggest that there is very little reliable data from the construction industry that characterizes exposure levels to various hazards including WBV or the health outcomes from such exposure and that there is a need for more exposure data. In a recent exploratory study of heavy construction equipment Cann (Cann, Salmoni, Vi, & Eger, 2003) looked at vibration levels for 14 different types of construction equipment. Eight of the 14 pieces of equipment tested exposed operators to levels of WBV that exceeded the recommended limits for an 8-hour period when comparing the measured VDV to the ISO 2631-1 standards. The purpose of the present research was not only to test a larger number of scrapers but also to investigate scraper operator exposure to whole body vibration (WBV) separately for each task. Methods 33 scrapers were evaluated for WBV in a variety of residential and road construction projects. Testing equipment consisted of triaxial accelerometers that allowed vibration data collection in all three orthogonal axes, with the x-axis positioned to measure vibration in the anterior-posterior direction, the y-axis in the medial-lateral direction, and the z-axis in the vertical direction. Root mean square accelerations (aRMS), vibration dose value (VDV), crest factor, and maximum transient vibration values (MTVV) were derived from this software and exported to an Excel™ spreadsheet for later data analysis. Test sessions for each piece of equipment lasted for approximately 20 minutes until at least three work cycles had been completed. Tasks included: idling while waiting for a bulldozer to push the scraper through the scraping phase, scraping, traveling loaded with dirt, dumping and traveling empty. Results Task breakdown by time reveals 25% of the work cycle was spent traveling fully loaded with dirt, 19% dumping, 21% traveling unloaded, 17% idling and 18% scraping. Calculation of aRMS vector sums gave values of 2.55 m/s2 during loaded transport, 2.46 m/s2 during dumping, 2.31 m/s2 during unloaded travel, 0.55 m/s2 during idling and 1.46 m/s2 during scraping (see Table 1). The highest acceleration values recorded were found in the z-axis during fully loaded transport reaching an average aRMS over three work cycles of 2.55 m/s2.

Jan 6, 2006

By William R. Wessels

This report describes a field survey and laboratory investigation into the causes of failure of resiliently clad screen decks applied to coal preparation plants. Blinding of screen deck perforations and delamination of the resilient cladding are studied and mechanisms responsible for these failure modes are hypothesized. A laboratory test program to simulate the mechanisms was begun and abandoned when it became apparent that meaningful test results would require a substantially redirected effort. No meaningful test data was obtained from the laboratory simulation.

Jan 1, 1982

By Fred N. Kissell

In This Chapter [Measuring the gas emission from the coal Methane at the top of the silo Methane at the load-out area and Actions taken after a silo explosion] Methane accumulations in coal silos have resulted in the occasional silo explosion. These can be quite violent and dangerous because coal dust adds to the strength of the blast. However, with the appropriate precautionary measures, methane accumulations in silos can be greatly reduced. Mine Safety and Health Administration (MSHA) regulations at 30 CFR2 77.201 require that the methane content in the air of any coal silo be maintained below 1.0 vol %.3 Also, MSHA requires that methane tests be conducted before any electrical equipment is energized, unless a continuous monitor capable of deenergizing the electrical equipment is used.4 Measuring the gas emission from the coal. The first necessary step in dealing with silo methane issues is to measure the gas emission from the coal going into the silo. Such measure-ments allow one to estimate the silo ventilation needs and permit a comparison with the methane controls used at other mines that have similar gas levels. The gassiness of the coal can be measured by taking conveyor belt grab samples.5 Matta et al. [1978] measured the gas emission from conveyor belt grab samples using a simple desorption test. To conduct the test, they collected several grab samples of coal, weighing a few pounds each, from the conveyor belt entering the silo.6 They then sealed the coal into an airtight sample container that was equipped with a valve and short hose along with a pressure gauge. Every few hours they opened the valve and bled the emitted gas into a water-filled graduated cylinder that had been inverted and placed in a pan of water (Figure 11–1). The results are shown in Figure 11–2.

Jan 6, 2006

Horizontal holes are drilled underground into coalbeds to control methane flow from ribs and active face areas and to make gas pressure measurements in coalbeds. Gas pressure measurements are made by drilling the same hole incrementally. After each increment, the hole is filled with some type of packers and allowed to reach equilibrium before a gas pressure reading is taken. As the length of hole increases, more packers are required to effect a seal and obtain a reliable pressure measurement. Problems have been encountered in obtaining satisfactory packer seals due to the friable nature of the coalbed. New methods of packing the holes must be used. Therefore, this project was established to evaluate materials and develop a new technique in which a semiliquid and/ or rigid type grout could be placed in the hole to provide satisfactory sealing.

Jan 1, 1972

By PALMER LARSEN

INDEX TO GEOPHYSICAL ABSTRACTS

May 1, 1931

By R. Ward Stahl

The underground junction or intersection is analogous to the doorway or window in a building in that the continuous wall or support for the overhead structure has been weakened by making the opening. Some type of bridge or support seems necessary to prevent roof sag and possibly eventual failure at this point, although frequently it appears that little is done until a fatal accident induces action. The intersection generally represents less than 15 percent of the exposed roof area. As a result of recent multiple fatalities, some of which occurred at or near intersections, the Bureau of Mines was asked to examine the junction-support problem more thoroughly and to report its findings. A national survey of the junction-support systems in use has been made by correspondence, and the local area has been canvassed rather thoroughly to determine just what and how much is being done.

Jan 1, 1962

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

By R. Newman

An inexpensive slow-speed data acquisition system has been adapted to digitally record multiple parameters simultaneously at intervals of 15 seconds. The system was built for use with standard soils testing equipment to automatically record load and displacement parameters at predetermined instants in time. Simultaneous readout is achieved by the use of special signal conditioner and sample-and-hold circuits which read the multiple signals simultaneously and hold them until the slow acting system can print out. Three channels of a 10-channel system have been converted and found to operate successfully during a series of direct shear tests. A unique feature of the system, which significantly reduced its cost, is the power supply units. Dummy circuits are used to maintain a constant power demand during sampling) thus eliminating the need for a costly power supply with rapid response characteristics. The entire system, having an overall accuracy of 0.25 percent, was put in operation for a cost under $2,500.

Jan 1, 1970

To predict the spontaneous combustion potential of bituminous coals using a simple expression based on an easily acquired coal property. Background Approximately 20% of underground coal mine fires in the United States since 1978 have been attributed to spontaneous combustion. Spontaneous combustion fires in underground mines are most likely to occur in gob area; and are difficult to detect and to extinguish by direct fire fighting methods. Often, sections of the mine or the entire mine must be sealed for long periods, at a great economic loss to the mine operator, mine employees, and the surrounding community. It is conservatively estimated that the cost of scaling a large mine is about $50 million.

Jan 1, 1989

By R. L. Gall

This report describes Bureau of Mines experiments in gasifying coal in a helium-heated tube-coil reactor. The purpose of this work was to investigate helium as a medium for transferring heat from a nuclear reactor to gasify coal or for use as high-temperature process heat. A laboratory-scale system was designed and constructed to demonstrate feasibility. In preliminary tests with this system, in which the coal was fed as a water slurry, the helium-heating and recycling equipment operated well. Considerable difficulty was experienced, however, in preheating coal slurry to the desired range of 400° - 1,000° F. without plugging the preheaters. Five different preheaters plugged with coke or with salts leached from the coal. The longest operating period wan 12 hours. These difficulties were partly due to the relatively small equipment and flow rates. The gasifier processed l pound per hour of low-rank coal at 300 p.s.i.g. and 1,800° F., with the carbon conversion limited to 20 to 30 percent by the short residence time and slow heat-transfer rate.

Jan 1, 1962

The above referenced contract between Badger Manufacturing Corporation and the U. S Bureau of Mines was executed June 30, 1975, as a result of the request for proposals for innovative machine concepts. We selected the cutting machine category because of the obvious lack of technical progress in this field for many years: Phase I of the contract required blasting fragmentation tests to determine proper blasting patterns for use with the auger-type kerf cutting machine. Phase II required design concept development for a machine capable of cutting a circular void as an aid to blasting.

Jan 1, 1975