Search Documents

By Jeffrey S. Walker

The purpose of this U.S. Bureau of Mines effort was to determine if ground movement caused by mining-induced subsidence is directly transferred to a structure and, if so, how that transfer takes place. Four concrete block walls with foundations were constructed and monitored over an active longwall panel. Three of the walls were located perpendicular to the direction of mining in zones where maximum inclination, maximum tension, and maximum curvature were predicted to occur. The fourth wall was constructed along the centerline of the panel, parallel to the direction of mining. All of the walls and the surrounding ground surface were instrumented with conventional survey monitoring points and extensometer stations to observe the vertical and horizontal movements. The fourth wall instrumentation also included continuously recording tiltmeters. The results of this investigation indicate that these simple structures respond to subsidence in a similar manner as the ground surface. This suggests that once the transfer mechanism is more fully defined, prediction models can be developed to accurately estimate the effect of mining on surface structures.

Jan 1, 1989

By Ren G. Dong, Richard McCormick, Dan E. Welcome

Vibration exposure at workplaces is generally multi-axial. The health effects of vibration exposure also likely depend on the vibration direction. Therefore, there is a wide interest in the simulation of multi-axial vibration in laboratory experiments. Advances in technology have led to the development of a new 3-D test system for studying hand-transmitted vibration exposure and health effects. The purposes of this paper are to introduce the system and to present the results of its preliminary evaluations. Test System As shown in Figure 1, the system is basically composed of three vibration generators, a multi-axis vibration control system, instrumented handle, handle fixture, and shaker-fixture linkages (stingers). [ ] Figure 2 shows the array of three vibration generators (MB Dynamics, Energizer BLACK-500 lbs) and their associated support bases and foundation developed by MB Dynamics (Cleveland, USA), which create the 3-axis simultaneous motion. These electrodynamic exciters are powered by power amplifiers which provide current proportional to the analog drive signal from a controller. The controller (JAGUAR Multi-Input/Multi-Output closed-loop vibration controller) was provided by Spectral Dynamics, San Jose, California, USA). NIOSH-designed instrumented handle was equipped on the system.

Jan 6, 2006

By D. Harry Chambers

The Bureau of Mines, through a memorandum of agreement with the Department of Defense, conducted research to recover silver from aircraft scrap. Silver was recovered by an electrolytic method from stainless steel honeycomb sections separated from the aircraft. These sections had been constructed by sandwiching a stainless steel honeycomb core between stainless steel sheets and then brazing the assembly with a silver alloy. Over 300 pounds of silver was used in the B-58 bomber, concentrated in certain honeycomb sections of the aircraft. Following shredding of the aircraft parts, an average of 95 percent (ranging 67 to 100 percent) of the silver was recovered in a single electro-refining step. After the electrorefined product was magnetically cleaned, purity of the recovered silver was greater than 99.3 percent.

Jan 1, 1980

By T. A. Sullivan

The work described in this report was undertaken to evaluate and develop techniques for determining the oxygen content of titanium and titanium alloys. Early investigations of volatilization techniques involving halogenation were unsuccessful. Later efforts were concentrated on evaluating vacuum fusion and inert-gas fusion techniques. Two vacuum fusion methods and an inert-gas fusion method were found to be satisfactory in the 0.02 to 1.00 pct., oxygen range. These methods are described in detail. The coefficient of variation by any of the three methods is approximately 5 pct, While the main portion of this paper is devoted to the vacuum and inert-gas fusion methods, a resume of other suggested methods for analyzing titanium for oxygen also is given. INTRODUCTION The Federal Bureau of Nines has conducted research on titanium metal since 1938. This research included development of the Kroll process for the production of titanium (2)4, various sodium reduction processes for making titanium metal and lower valent titanium chloride-sodium chloride mixtures (17), and a fused salt electrolytic process for Me production of high-purity titanium metal and the recovery of titanium by electrorefining from off-grade materials (20).

Jan 1, 1961

By J. McCoy

Charged sprays and fog have been evaluated for reducing respirable dust concen¬trations. Charged spray technology was reviewed for effectiveness, equipment and theoretical considerations. A mathematical model was developed for predicting dust reduction effects. Laboratory tests were made showing charged spray is considerably more effective at reducing dust on a unit water basis than hydraulic spray. Positive and negative sprays are equally effective. Combined polarity sprays are considerably less effective than either polarity alone. Little difference in effectiveness by dust type was observed. The charged cloud can present a spark hazard in explosive atmospheres. Due to this spark hazard from the charged droplet cloud this technique must not be used in gassy mines. Predictions were made for field test conditions but confirmation was impossible due to particles resulting from dissolved solides in the spray water. Dissolved or suspended solids in atomizing sprays can result in an increase of the respirable dust burden. Charged sprays are an available dust control technique best suited to applications where water usage must be limited and long contact time between spray and dust is possible.

Jan 1, 1983

By Thomas M. Barczak

Secondary roof support systems play a vital role in preserving the safety of underground mine workers by preventing the unintentional collapse of the mine roof. Hundreds of thousands of standing roof supports are constructed each year in underground coal mines. Historically, wood and concrete cribs and timber posts have been used for secondary roof support. These support constructions require the handling of heavy and bulky materials, causing numerous injuries to the mine workers and resulting in more than 40,000 lost workdays in the past 9 years. Since 1993, various alternative support technologies have been developed. These new support technologies not only provide superior roof support, but many also have significant material handling advantages by using smaller and lighter weight materials, fewer components, mechanically installed support systems, and pumpable support systems. The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive material handling research and has developed recommended lifting thresholds to reduce material handling injuries. An analysis of roof support construction reveals that conventional support materials used in wood and concrete cribbing exceed the recommended lifting thresholds, while the engineered support systems are closer to the recommended weight thresholds. Finally, recommendations are made relative to proper lifting techniques and material handling practices to prevent injury to mine workers when constructing roof supports in underground coal mines.

Jan 10, 2000

By H. G. Wolfhard

The propagation of explosions through short cylindrical channels has been investigated by the Bureau of Mines. In the experimental apparatus set up by the Bureau, a single such channel formed a connection between a small explosion vessel in which a gaseous explosion was initiated and a larger, partly enclosing, explosion vessel filled with suitable gaseous mixtures; the larger vessel permitted observation to determine if an explosion was induced therein by mass, energy, and species transfer through the channel, as a result of tie initial explosion, It has been found that transmission of flame through to channel is not an essential to induce the second explosion, for hot gases from an extinguished explosion are able to ignite cold combustible mixtures in the larger vessel. The schlieren patterns of flames or hot burned gases emerging from a channel into the explosion chamber were photographed. These show, in most instances, that vortexes of hot gas ejected from the jet into the cold explosive mixture are responsible for ignition. The study has practical significance in problems of rendering electrical equipment safe for use in potentially flammable atmospheres, INTRODUCTION The propagation of flames through cylindrical or annular channels has practical importance in flameproofing electrical equipment and for flame traps. Much practical work has been done to determine the minimum safe breadth of flanges and the maximum safe gap between the flanges that will permit venting an electric motor without allowing flames to pass.

Jan 1, 1959

By J. T. McLendon

As part of its research project in developing improved refractory materials for metallurgical applications, the Federal Bureau of Mines obtained hot modulus of rupture data at 1,500°,1,550°, and 1,600° C on samples of 13 refractory periclase materials produced from seawater, lake brines, and natural magnesite. The periclase samples also were characterized to establish chemical and mineralogical composition and microstructure. The results indicated that a high MgO content does not necessarily assure good hot strength and that an optimum and varying CaO-Si02 ratio exists for each individual periclase sample.

Jan 1, 1979

By Liming Yuan, John C. Edwards, Gene F. Friel, Robert A. Franks

Diesel fuel fire experiments were conducted in NIOSH’s Pittsburgh Research Laboratory’s (PRL) Safety Research Coal Mine (SRCM) to determine the critical air velocity for preventing smoke rollback. Such information is necessary for the preplanning and implementation of ventilation changes during mine fire fighting and rescue operations. The fire intensity varied from 50 kW to 300 kW depending upon the fuel tray area. Airflow in the 2 m high and 2.9 m wide coal mine entry was regulated during the course of each experiment; measured upwind from the fire as an average over the entry cross-section with an ultrasonic airflow sensor; and recorded dynamically with a mine monitoring system. The extent of smoke reversal was monitored with light obscuration monitors, ionization smoke sensors, and visual observations. Experimental results for the critical air velocity for smoke reversal as a function of fire intensity compared very well with model predictions based upon a computational fluid dynamics (CFD) fire dynamics simulator.

By John P. Borovsky

A 3-year study was conducted to evaluate the problems and benefits of using vegetation to stabilize tailing from a potential Minnesota copper-nickel milling operation. The project consisted of three separate investigations: a waste characterization study, a greenhouse study and a field study. With few exceptions, the physical and chemical characteristics of the tai ling were found to lie within the range of properties of Minnesota soils. The tailing lacks organic matter; is deficient in nitrogen, phosphorus and potassium; and may contain elevated levels of soluble salts and heavy metals, particularly copper and nickel. Numerous grasses, forbs and woody plants will tolerate the tailing as a rooting medium. Peat incorporation and topsoil dressing provided few benefits to the revegetation process which were not provided by a fertilizer application. With fertilization, grass/legume production in the tailing was comparable to local agricultural yields. Concentration of heavy metals in grasses grown in the tailing were generally below suggested tolerance limits for plants and animal forage. Legumes tended to accumulate higher concentrations of copper and nickel, and metal uptake of most plants was positively correlated with rate of fertilization. Tailing drainage water contained elevated levels of heavy metals, and establishment of vegetation had little effect on the quantity and quality of tailing drainage water. However, topsoil dressing significantly increased drainage water volume when compared to unvegetated control plots. Copper-nickel tailing revegetation recommendations were developed.

Jan 1, 1983

By K. K. Kelley

Thermodynamics data for silicates have applications in the fields of extractive metallurgy, ceramics, and geochemistry. To facilitate these applications, up-to-date tables of heats and free energies of formation are needed. It is the purpose of this report to supply such tables for anhydrous silicates. During the last 15 years the heats of formation of a substantial number of anhydrous silicates have been reliably determined at or near room temperature. This resulted from the development (first by the Bureau of Mines and later by the Geophysical Laboratory of the Carnegie Institution of Washington, by the Institute of Geology of the University of Helsinki, Finland, and by the Department of Geology of the University of Chicago) of accurate solution calorimeters, employing hydrofluoric acid as the reaction medium. Specific references to work of these laboratories will be made in the next section of this report. Also, entropy data at 298.150 K. and high-temperature heat-content values are available for many of these silicates, mainly owing to work of the Bureau of Mines. Most of these entropy and heat-content data have been compiled in Bureau of Mines Bulletins (13, 15).3

Jan 1, 1962

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations wi.thin a multiple-seam configuration. At two mine sites where such ground interactions were present, the Bureau performed a complete geological analysis and installed and monitored instrumentation to gather pertinent data on rock mechanics. Overburden depth varied dramatically in the vicinity of the study area and reached a maximum at the study site; innerburden thick-ness was less than a pillar width (40 to 4S ft); heaving was experienced in both mines where sandstone and/or shale floor units were observed; overlays of the mine layouts show pillars were not totally superpositioned; a maximum of S in of roof to floor convergence was measured; and pressure readings indicated pillar core loading only and increased to a maximum of 7,000 psig over instrument setting pressure.

Jan 1, 1987

By W. P. Diamond

The direct method test was developed for general mine safety applications by the U.S. Bureau of Mines in the early 1970's to measure the gas content of coal samples obtained from the relatively shallow depths of eastern U.S. coal mines. Over time, applications for gas content data evolved which required increasingly accurate desorption values. It became evident that some of the inherent weaknesses in the original direct method test could best be addressed by abandoning the water displacement based desorbed gas volume measurements. The ideal gas law based modified direct method (MDM) and associated desorbed gas volume measurement apparatus was developed to provide the most accurate desorption values possible for rock samples obtained from any gas-bearing strata. The MDM has a number of significant advantages, including: (1) increased accuracy, especially for low gas content samples, (2) a test apparatus with an integral sampling port to facilitate the collection of uncontaminated gas samples, (3) an inherent head space effect correction in the periodic MDM desorbed gas volume calculations, (4) measurement of positive and negative desorbed gas volumes, (5) elimination of differential gas solubility effects as a source of error inherent in the water displacement methods, and (6) a compact and rugged test apparatus that along with the elimination of the ?glassware? required for the water displacement methods, facilitates its use in the field.

Jan 1, 2008

By Marcel Vanpee

Eight extinguishing powders KCI, were tested on five types of diffusion flames. The effect of flame temperature on the inhibition efficiency was investigated by varying the oxygen index of the flame supporting atmosphere. Inn addition a spectrographic investigation of powder flame dissociation products was carried out on the methane/air/ABC (NH4H2PO4) flame. Dissociation products for this flame included P0, PH, NH, and Na. It is concluded that the main factor to be considered in the efficiency of tie powder is the flame temperature Purple K (KHC03) was typically inefficient in low temperature flames and very efficient in high temperature flames. On the other hand, ABC (NH4H2PO4) was found to lose its efficiency at high temperature but to be quite efficient in the low temperature flames. The effect of temperature is offered as an explanation of the poor efficiency of Purple K (KHC03), against coal dust explosions as contrasted to the high efficiency of phosphate salts against coal dust explosions.

Jan 1, 1982

By M. A. Trevits

During the time period from 1990-2007, 1601 reportable fires occurred in the U.S. mining industry (an average of 89 fires per year). The leading causes of U.S. mine fires were flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion. The fact that mine fires continue to occur with an alarming regularity reinforces the importance of recognizing and eliminating the potential hazards and the overall need for improved fire control and suppression technology to ensure the best possible outcome during a mine fire. The National Institute for Occupational Safety and Health (NIOSH) is conducting an evolving comprehensive program of research that is addressing mine fire prevention, detection, management and suppression. This paper presents a summary of recent research accomplishments and provides an overview of the next phase of the NIOSH mine fire research program.

Jan 1, 2008

By Louis Schaffer

The objectives of the research were to determine whether a model health and safety program could be defined in terms which would enable its application to mines of all types, and, if such a model program could be defined, to determine through evaluations in two mining companies whether it would achieve measurable improvements. Volume 1 describes the model, how it was applied in the field and how it was evaluated. This, Volume 2, describes the literature and field research that preceded the model definition.

Jan 1, 1983

By Bernard Baum

Combined preservative/fire retardant systems were pressure impregnated into Douglas fir and Ponderosa pine samples and evaluated for decay, flammability, and mechanical properties. The objective of the evaluation was to identify cost-effective systems for use with mine timber, and to provide an information and data base from which Federal code regulations could be established. Thirty systems, based on combinations of commercially available preservatives and fire retardant impregnants and coatings, were applied to Douglas fir samples and evaluated for decay and flammability. The ten most promising systems were ap¬plied to both fir and pine and reevaluated for decay and flammability before and after water leaching. The five best systems were given a thorough laboratory evaluation using both pine and fir. Evaluations included flame spread, smoke density, toxic gases, decay, compressive strength, flammability after artificial weathering, and cost. All systems had acceptable toxic gas levels and smoke densities, but flame spread was only borderline acceptable for most of the samples tested. A trade-off analysis showed Acid Copper Chromate/Fyrprufe with Albi-107A/144 intumescent paint and Koppers NCX to be the-best systems. Recommendations are made for further large-scale testing using the two best Systems.

Jan 1, 1978

By Stephen C. Tadolini, Yunqing Zhang, Thomas M. Barczak

Standing crib supports have been applied in underground mining programs to resist large roof movements and sustain high-loads. The strength and deformation capability of these systems has been documented under both laboratory and field conditions. The parameter that has not been examined and is not well understood is the effect that a crib or other types of standing support has on the primary and secondary bolting systems. A crib support system with low system stiffness may allow large amounts of closure and deformation and cause the bolting systems to yield or even fail. Conversely, cribs or standing support that are too stiff may experience brittle or buckling failures, negating the advantage of the intrinsic supports previously installed. Utilizing a combination of field measurements and 3-dimensional finite element modeling techniques, the relationship between system stiffness and the subsequent performance of the installed bolting system is evaluated. Additionally, a simple method for calculating the combined system stiffness for standing supports, when using materials with different strengths such as steel, concrete, wood, etc., is presented.

By Thomas E. Finch

This report is a continuation and expansion of a previous USBM grant (No. G0254004) which examined alternative methods of handling the parting between two coal seams in a surface mining operation. The alternative methods consist of equipment implementation in either a stowing or haulback technique. Following a typical strip mine conformation, the parting is directly stowed or hauled back and placed in the pit bottom after second seam removal. The objectives are to produce an environmentally sound material placement technique and to increase prime stripping machine utilization. This report contains the engineering philosophy behind two computer programs created to evaluate parting handling methods over d wide range of coal and parting thickness ratios. The nature of the computer approach allows cost sensitivity analysis and quick updating of costs. The two programs are clearly presented with documentation and examples such that consumers may apply then to their own operations.

Jan 1, 1977

By B. J. Moore

The Bureau of Mines has estimated helium resources of the United States at 727 billion cubic feet as of January 1, 1979. These resources are divided into four categories in decreasing degrees of assurance of their existence: (1) Helium in storage and in measured natural gas reserves, 185 billion cubic feet; (2) helium in indicated natural gas resources, 150 billion cubic feet; (3) helium In hypothetical natural gas resources, 186 billion cubic feet; and (4) helium in speculative natural gas resources that makes up the remaining 206 billion cubic feet. The identified helium reserves, which are made up of that in measured and indicated natural gas categories, are further divided into depleting, non- depleting, and stored classifications. The depleting resources are those that are associated with natural gasfields that are, or will be, produced for the natural gas they contain. All of the helium in undiscovered natural gas resources are included in this classification. These depleting resources comprise 600 billion cubic feet of the total resource base. The nondepleting helium resources are estimted tototal 88 billion cubic feet. There is 39 billion cubic feet of helium in storage in Cliffside gasfield near Amarillo, Tex.

Jan 1, 1980