Search Documents

By D. Izerdem, S. L. Ergun

"Beneficiation of the finely disseminated valuable minerals has been an important issue in the mineral processing field for decades. Treatment of the fine materials becomes difficult with using traditional gravity concentration equipment. To investigate particles behavior in a commonly used conventional gravity concentration equipment, a comprehensive study was undertaken in a plant, which only consists spiral concentrators as concentration units. Spiral concentrators require relatively coarse material to effectively concentrate valuables as well as offering greater simplicity for especially higher grade feeds. In the current work, chromite ore (d80 = 290 µm) was treated using spiral concentrators and the performance of spiral concentrators was examined. The design of the separation circuit comprised of rougher, cleaner and scavenger stages. The resultant fractions produced by each separation unit and feed samples were analyzed to identify the particle sizes, mineral liberations and chromite content. Grade and recovery comparisons were presented in size-by-size manner and the separation tendency of the particles were determined in varying feed rate conditions. The overall results indicated valuable mineral loss of the plant and alternative suggestions were pointed to reach the target values.INTRODUCTION Spiral concentrators are simple low energy consuming devices, which are generally used for pre-concentration of the minerals. They are cost efficient equipment separating minerals mainly based on density differences of the minerals. The adjustable splitters remove the concentrate as the remaining stream continues to move down the spiral. Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational force, centrifugal force, hydrodynamic drag and Bagnold force (Atasoy and Spottiswood, 1995; Burt, 1984). Since the classification in a spiral concentrator depends on particle specific gravity and size, the operation of spirals can be analyzed using size recovery or partition curves (Bazin et al., 2014). Spiral concentrators possess multiple design parameters for a variety of applications. The design parameters that govern the performance of the spiral can be identified as the diameter, number of turns, slope, pitch and the profile of the trough. For an efficient separation on a spiral concentrator, the properties of the slurry flowing on a spiral, ore texture, percent solids and flow rate play important roles."

Jan 1, 2018

By A. F. Usov

A potential of electric pulse disintegration in benification used for primary deposits ores containing precious metals is shown. Of special significance is that PGM and gold grains, being highly plastic, are easily liberated and are not smeared on the disintegrated rock fragments surface. It al-lows gravity separation, which is less expensive and more efficient, to be used instead of chemical processing, which is expensive and environmentally faulty.

Jan 1, 2014

By L. X. Zhang

It is very important to improve the A/S of the bauxite to keep sustaining development of Chinese alumina industry. This article summarized the issues of several desilication technologies, which are named as normal flotation, reverse flotation and bi-flotation. Normal flotation has been got industrialization because of technologic advantages. The campaign experiment of reverse flotation which has principle advantage was carried out in 2004, and bi-flotation which is combined the advantages of both the normal flotation & reverse flotation has the most attractive future. The development of bauxite flotation will be focused on multi-utilization of bauxite by mineral process technology and corresponding equipment which satisfied with the flotation technology and reagent.

Jan 1, 2014

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisinger

"INTRODUCTIONThe objective of this work was to deport silver into a residue suitable for subsequent extraction without compromising the high base metal extraction during the pressure oxidation.RESULTS AND DISCUSSIONThe complex sulphide from the tailing pond of Cannington mine, Australia, was re-grounded and a bulk concentrate was recovered by flotation. The major economic sulphides are galena and sphalerite. The chemical analyses revealed 17.22% Fe; 4.88% Zn; 8.22% Pb; 9.49% S2- and 422 g/t Ag. The baseline cyanidation yielded 36.60% of silver at high cyanide consumption (24.17 kg/t NaCN). Pressure oxidation at 150°C (in the absence of iodide), followed by cyanidation of the residue yielded 8% silver extraction. Pressure oxidation was carried out at 110-150°C in sulphate media with additions of potassium iodide and the resulting residue was subjected to cyanidation. High recovery of silver was achieved because its incorporation into lead-hydronium jarosite during the pressure oxidation was minimised, while its deportment into the cyanide-soluble silver iodide was favoured (Figure 1). Silver recovery decreased slightly at high temperatures (140° and 150°C) because of the enhanced stability and kinetics of leadhydronium jarosite, but this could be overcome by increasing acidity and iodide concentration of the slurry."

Jan 1, 2003

By Egbert Burchardt

"Some of the challenges faced by the mineral industry in the future are the need to process low grade ores at the lowest operating cost, to deal with elevated energy cost and to address scarce water resources in some regions of the world. These challenges will increase the demand to develop highly energy-efficient and less water-consuming mineral processing systems. Experience from other industries suggests that HPGRs could help to achieve these goals, due to their high energy efficiency and their ability to be used as dry grinding systems. Historically, HPGRs have been used mainly as tertiary crushers in mineral applications for the production of ball mill feed. In the cement industry, however, HPGR systems have been successfully applied for grinding limestone, clinker and slag to a final product fineness (p80) of between 30 and 90 µm without the need of downstream ball milling. The total energy consumption of HPGR finish grinding systems in the cement industry has been found to be 30 to 50 % lower than in ball mill systems. This leads to the question of whether the same methodology can be adopted in the mineral industry. Such a step would require the use of dry rather than wet grinding systems. Traditionally, dry grinding systems have been only an exception in mineral processing, since most post grinding processes are wet. However, there are successful - mainly ball mill based - dry grinding examples in gold, nickel or iron ore. Experience from some of these dry grinding references are summarized in this paper. In addition, this paper explores two future-orientated questions: What opportunities does HPGR finish grinding offer the mineral industry? What are general conditions and challenges for adopting this technology for mineral applications?"

Jan 1, 2014

By M. Amani, A. Akbarinasab, M. Bazmandeh

The fourth iron ore production plant at Golgohar mining and industrial company consists a ball mill and wet medium intensity magnetic separators (3500 Guss). The ball mill product applies directly into MIMS and the MIMS concentrate directly transfers to the low intensity magnet separators (LIMS). The thickener is used for dewatering of MIMS and LIMS tailings. By sampling from streams of ball mill and separators, it was defined that the grade and iron recovery were 60% and 80% respectively while they would be 66% and 90% respectively based on the designing documentation. The average of P80 in the ball mill was 342 micron in a month that is coarser than optimized value. This problem was related to unsuitable operation of grinding. For optimization of grinding efficiency, the amount of charge volume was investigated as a variable. The measurements illustrated 32% charge volume. For increasing grinding efficiency, the charge volume was increased 1% and 1.6% in two stages. The results showed ball mill power draw average reached from 3650 kw to 4120 kw and the average P80 reached to 329 micron. All of parameters calculated about 35 day before and after change. Average of Ball mill feed iron ore grade before and after change was 49.24% and 50.32% respectively. This change caused an increase in efficiency of MIMS, where the enrichment ratio and concentrate grade increased 2% and 1.9% respectively. For increasing the iron grade of the MIMS concentrate; the orifice of the tail flow exit pipe changed from 4 inch to 6 inch and the concentrate grade increased 2%.

Jan 1, 2014

By Manuel Diaz

"In these difficult times for the mining world, mainly due to the global uncertainty about metal prices and the increased activity of opponents to the mining industry, it is essential that mining companies focus on efforts and strategies that will give them the most flexibility to succeed under the fury of these phenomena. The careful management of systems to control costs, and indicators to measure with great precision actual variations in costs and cash flows, are essential to adequately manage the uncertainty. Similarly, clear corporate and regional strategies designed to maximize cash flow and operating margin will allow the company to be better prepared to face any negative situations caused by declining metals prices, stricter government regulations and increasing social pressure. Gold Fields Limited, a corporation of South African origin and with more than 100 years in the gold mining business, has developed the ability to adapt to large changes generated by different global crisis throughout its history. This occasion will be no different. Given the critical situation of the mining industry in the world today, Gold Fields has embarked on a re-structuring plan at global level that will allow much closer control and real efficiency of production costs. This plan includes the creation of regional business units that allow greater independence for each region while still preserving the standards and cultural values of the Corporation. This presentation will explain why we believe that this approach combines the best aspects of the two styles of business, and what are the expected results. In the Americas Region, Gold Fields currently operates Cerro Corona, in Peru. In addition, the company is considering opportunities for growth in Chile, Brazil, Mexico and Canada."

Jan 1, 2014

By Häkkinen Antti, Salmimies Riina, Matveinen Maria

"Tailings generated during the upgrading of ore present a major challenge for the mineral processing industry. On one hand, the processing of tailings requires added capital input. On the other hand, increased difficulties in obtaining permits for dams and landfilling and increased costs associated with storage and tailings management also result in increased costs. To promote sustainability and make tailings management economical, added value must be generated from the waste material. This might be possible through the recovery of the metal values in the waste. This work discusses the possibilities of recovering metals from multimetal tailings through leaching in a stirred tank. The characteristics of the tailings are crucial and the distribution of the metals within the different size fractions is used to identify the most attractive route for the hydrometallurgical step. Leaching of nickel and copper is further investigated using acids at different concentrations. The leaching of base metals is possible at acidic conditions. Increased temperature and concentration of the leaching agent promote the dissolution of the metals, as could be expected. With simultaneous dissolution of several metals the dissolution mechanisms are difficult to identify. Furthermore, as several metals, not all of them being target elements, are leached another challenge arises from the selective recovery of those metals from the liquid phase."

Jan 1, 2014

By A. Boulton

Low molecular weight synthetic polymers substituted with hydroxyl, carboxyl or sulfonate functional groups were used to improve the flotation separation of zinc or copper sulfide minerals from iron sulfide gangue minerals in three massive sulfide ores of different mineral composition. These polymers produced significant improvements in zinc or copper grades as a result of a selective depression of iron sulfide minerals. These results are significant considering the differences in ore type, proportion and type of iron sulfide minerals present, and grinding medium used in this study.

Jan 1, 2003

By Cesar Gomez, Jaime Álvarez, Lisette Wen

Laboratory mechanical flotation cells are extensively used in mineral processing for running batch flotation tests with a variety of purposes, for example assessing feed characteristics, determining flotation kinetics, or testing of new reagents and procedures. It is known that the results obtained depend on the operation mode, self-aerated or forced-air, and on the operating conditions selected for the test, in particular impeller speed and gas flow rate. These different results are a consequence of changes in size distribution of the generated bubble population and its remarkable evolution when frother is added; variations in bubble size affect the bubble surface area flux (BSAF), a variable which correlates with particle collection. Results of a two-phase (air-water) test program designed to measure bubble size for a variety of combinations of impeller type and speed, gas flow rate, frother type and concentration, and cell volume, demonstrated the wide range of BSAF with which the cell can be operated. The results obtained in this work demonstrated that gas dispersion in a forced-air lab flotation machine is significantly affected by the characteristics of the impeller/cell geometry combination in use, and the operating conditions selected. Operating conditions must be carefully selected and maintained during the test to ensure consistent results, in particular when frother concentrations below 20 ppm are used, because frother concentration in the cell will decrease as flotation progresses as a consequence of frother partitioning to the concentrate.

Jan 1, 2014

By G. Weingrill, H. Flachberger, J. Neubacher

The so called Bublon®-process is an innovative process for the controlled expansion of volcanic glasses such as Perlite and for thermal treatment of other minerals. In this manner, functional light fillers with astonishingly altered physical properties can be manufactured. In contrast to conventional Perlite expanding processes no fossil fuels are burned in order to achieve the expansion. Instead, the feed material is heated electrically mainly by radiation based on heat transfer from heating elements. The main advantage is the better controllability of the production process. Therefore, the heating elements are segmented along the flow of the particles, hence in direction of the ongoing expansion. Overheating of the particles, which ultimately leads to the destruction of the particle surfaces and consequently decreasing the quality of the expansion product, can be reduced significantly. Due to flow characteristics and settling behaviors of fines the lower particle size limit of the feed in this process is restricted to not less than 100 µm. Otherwise process instabilities are to be expected. Manufacturing industry demands light and fine hollow microspheres. Therefore, a proven cooperation between Montanuniversität Leoben and Bublon GmbH was formed to develop a new process called ‘Bublite’. This issue was addressed by changing the conveying principle into a pneumatically conveying system transporting particles from the bottom to the top of the kiln by the means of a drag flow. This approach makes it possible to handle the difficult flow patterns in the kiln and to control the retention time of the particles in the heat transfer zone. As a result, it is now possible to expand very fine Perlite particles into a high quality functional lightweight filler with a glazed-closed surface. The dependence of the polymer industry on importing this kind of fillers from overseas can be reduced by producing it close to sites of demand. Also the Perlite mining and processing companies benefit from this technology because the mine lifespan and the output of the processing plant can be increased.

Jan 1, 2018

By David Newton, Christian O’Keefe, Robert Maron, Jerin Russell, Paul Rothman, Dylan Cirulis

"The presence of unwanted coarse material in flotation feed streams negatively impacts both recovery and throughput of concentrator plants. The detection of this coarse material is a long-standing problem in mineral processing that has been poorly addressed by existing instrumentation systems. This problem has been overcome by the development of two new systems that detect in real-time the presence of coarse material in the overflow stream of individual hydrocyclones. They both use sensors mounted to the overflow pipe of the hydrocyclone and provide a robust and maintenance-free system measurement that enables corrective actions through operator intervention or automatic control strategies. One system is non-invasive and detects very coarse material 6mm or greater in size. The other system uses a wetted sensor and detects coarse material down to a lower size limit of approximately 100 um. Both systems have been commercially deployed. The systems will be described in detail. Validation data and typical plant data will be shown"

Jan 1, 2014

By Wenying Liu, Marek Pawlik

Long-chain ionic surfactants, with fatty acids and amines as the most important representatives, are widely used as collectors in froth flotation. These surfactants, generally referred to as weak electrolyte collectors, frequently form solid insoluble precipitates within a certain pH range. However, the action and behavior of these colloidal precipitates in froth flotation systems are not well understood and has not been well decoupled from those of dissolved forms. The objective of this study was to understand and compare the role of colloidal precipitates with that of the dissolved forms at gas-liquid and gas-liquid-solid interfaces. Using primary amine as the model surfactant, experiments were carried out to measure: the maximum volume of bubbles generated in the presence of dissolved and precipitated forms of the surfactant; surface tension for both forms of the surfactant using the drop shape and maximum bubble pressure methods; and contact angle using the sessile drop method. The experimental results showed that: in the presence of the precipitate, bubble volume was smaller, which was correlated with the lower surface tension and higher contact angle measured; the surface tension of solutions containing surfactant precipitate was affected by the surface age of liquid droplets. This study enhances understanding of the interfacial behavior of long-chain ionic surfactants under different conditions, which would help improve the efficiency of reagent utilization in froth flotation.

Jan 1, 2014

By R. Chowdhury

Axis House manufactures and supplies alkylhydroxamate reagent of various carbon chain lengths for application in flotation of oxide copper and other minerals. As part of reagent performance improvement the structural factors of hydroxamate are examined by various analytical tools in particular with X-ray diffraction of single crystals. In a recent publication, the structure of n-octylhydroxamic acid and its corresponding potassium salt are presented with findings of hydroxamic functional group geometric preference, H-bonding, keto-enol tautomerisation, acid-salt aggregation and alignment of carbon chain. In this paper an example of branched alkylhydroxamate 3, 5, 5-trimethylhexylhydroxamate will be presented and compared with the result of linear alkylhydroxamate.

Sep 1, 2012

By Andrey Kozlov

The results of mineralogical?technological studies of PGM mineralization in zoned mafic?ultramafic complexes of the Ural?Alaskan type are given. The most important technological specificity of PGM mineralization hosted in dunites is its occurrence only in the form of free mineral species with predominance of Fe?Pt alloys (ferrous platinum, isoferroplatinum, and tetraferroplatinum). Technological properties, grain size, and good opening of PGM ore in grain size class +80 µm make it possible to concentrate ore using gravity methods with stadial comminution and between cycle separation of relatively large grains and nuggets into high-grade concentrates at the early stage of disintegration. Keywords: platiniferous dunites, PGM mineralization, mineralogical?technological studies and processibility research, recovery technology, gravity methods

Sep 1, 2012

By Reza M. Rahman, Seher Ata, Graeme J. Jameson

"This paper presents the results of a through investigation into the froth recovery measurements in a controlled plant environment using a device that allows direct collection of dropback particles from the froth phase. Test work was performed at the Northparkes concentrator (NSW, Australia), using a feed taken from the head of the cleaner scavenger bank. The feed slurry had a relatively higher copper grade varying from 5.2% to 6.8%. Experiments were performed to investigate the effect of important flotation parameters such as air flowrate on the froth recovery. The size of the particles in the relevant streams was also analysed to acquire in-depth knowledge about the froth dropback mechanism. The results suggested that the froth recovery could be as low as 70%, although it was relatively easy to achieve the values in the range 75% to 85% by the correct choice of operating variables. It was found that the air flowrate has a positive impact on both collection (pulp) and froth zone recoveries. However, the effect was more prominent in the froth zone. It appeared that the froth recovery is a strong function of particle size."

Jan 1, 2014

By R. C. Miranda

The purpose of this work is to present ?state of the art? mass balances closing strategies in ore treatment plants. It presents a brief history of difficulties and challenges ahead. The current methodology is based on usage of an expert system, which seizes and filters the plant data, analyzes situations of equipment stops and mostly instruments failures. It is still possible to internally create a strategy to check the data of an instrument failure. The system is coupled to software with a Lagrangian model of mass balance closure that receives the pre-treated data. Thus, the data goes through filtering and reconciling processes to generate a reliable mass balance of the ore treatment plant. This made possible to obtain a system that is able to tell the real productivity of a ore plant through reliable mass balances. Residence times on equipments are critical to the balance, thus, they require good logic to eliminate errors due to the characteristics of non-steady state. Among the next challenges is the inclusion of a ?soft sensor? as a replacement of an instrument required for mass balance closure.

Sep 1, 2012

By A. T. Sutaone

"In the Dongri Buzurg Manganese Mine of M/s Manganese Ore (India) Ltd., high grade lumpy manganese ore required for iron and steel industries is produced through multi-stage crushing and screening. This has resulted in accumulation of 50,000 tonnes of low grade fines over the years. This production of such fines is still going on. The fines create environmental problems, like air and water pollution and siltation in adjoining fields. Besides containing lot of manganese values, they occupy large space which is very scare in mining area.The Indian Bureau of Mines under one of its statutory functions has suggested the company to explore the possibility of recovery of additional values under conservation and environmental aspects. Hence the company has sponsored a bulk sample for beneficiation studies in the Modern Mineral Processing Laboratory and Pilot Plant of Indian Bureau of Mines at Nagpur, India. The main manganese minerals present in these mine rejects have been identified as pyrolusite and psilomelane. The purpose of this study was to explore the possibility of evolving a suitable beneficiation flowsheet to obtain manganese concentrates assaying over 72% MnO2 to be used as raw material for the manufacture of dry cell batteries.The sample/material was subjected to characterisation studies in terms of chemical analysis, granulometry and mineralogical compositions. Based on these characterisation studies, the beneficiation process developed comprised of desliming, jigging and low intensity magnetic separation mainly to reject quartz, silicates and jacobsite. The manganese concentrate thus produced assayed 70.2% MnO2 with MnO2 recovery of 78% and weight per cent yield of 63.5. This natural concentrate could be mixed with the electrolytic manganese dioxide produced by the company and this blend can thus be used as a raw material for the manufacture of dry cell batteries by the end users. The paper deals with the details of test work carried out in evolving the process flowsheet."

Jan 1, 2003

By S. Gomez, P. A. Bebswa, A. N. Mwale

"The research aimed at improving the way screen performance analysis is conducted using a model that accounts for most feed and design parameters in its formulation. Thus, the aim was to validate the fine screen model that was developed at the Centre for Minerals Research (CMR) unit at the University of Cape Town. Fine wet screening is increasingly becoming an important application in fine grinding operations. Minera Saucito, a lead-zinc Mexican mine has replaced hydrocyclones with eight stacks of five decker derrick screens to close the ball mill in their concentrator plant. The five decker stacks have improved the overall plant throughput by 20% and have had the ball mill circulating load reduced considerably. As a continuous plant optimization process, a number of surveys were carried out to assess the performance of the 75 µm panel aperture installed screens. The surveys were conducted at seven different feed rates to the entire nest of screens to collect performance data. Using the fine screen model to analyze the results, it is found that as the feed rate increase, the sharpness of separation reduces. The CMR fine screen model was fitted to these results. The model fits the plant data with good accuracy. Simulated results based on this model are also presented.INTRODUCTION The potential of high frequency vibrating screens has long been identified as an alternative to hydrocyclones in grinding applications (Rogers and Brame, 1985). However, high frequency vibrating screens have had two main disadvantages, low capacity and high wear rates (Kelley and Mckeon, 2005; Teknikk, 2009). Current vibrating screen technology overcomes these challenges by multiple deck screen design and use of wear resistant urethane materials for panel construction (Kelley, 2007; Valine and Wennen, 2002). For a example, the Derrick screen’s material of construction is a tensionable urethane that provide high open area ranging between 35 to 45% with considerably reduced blinding (Valine and Wennen, 2002). Thus, there has been an increased uptake by the mining industry in the use of wet fine vibrating screens closing the ball mill as the final classification stage in the comminution circuit (Barkhuysen et al., 2010; Frausto, Ballantyne et al. 2017; Pelevin and Lazebnaya, 2009; Teknikk, 2009). Even though there is a number of models in existence, none of these models adequately predict the performance of high frequency vibrating screens (Karra, 1979; Rogers, 1982; Subasinghe et al., 1990; Trumic and Magdalinovic, 2011). Recently Mwale et al., (2016) developed a model for predicting the performance of high frequency vibrating screens using the partition curve properties. The input parameters of the model include screen open area (??) in m2, tonnage feed rate (????) (tph) and the weight fraction of solids (??) in the feed for a given panel aperture size. The model was developed based on data collected from a single deck industrial size derrick screen, in a pilot setup. The work presented in this paper is an attempt to test this model using data collected from Minera Saucito concentrator, an industrial plant whose comminution circuit is shown in Figure."

Jan 1, 2018

By I. H. Mukhametshin, E. N. Baranova, I. B. Fadina, E. A. Ashirbaeva

The purpose of the research is the development of a complex of solutions for the maximum extraction of non-ferrous and precious metals from persistent mineral raw materials by heap bioleaching from spent heap leaching (HL) stacks. Methodical recommendations for assessing the suitability of primary and technogenic refractory mineral raw materials for heap bioleaching are developed. Active associations of microorganisms have been created for the conversion from various types of ores to the solution of S, Fe, As, Sb, Cu, Zn, Mn, Ni, Mg, P and other elements, as well as methodologies for their storage, immobilization and preparation of bioreagents in industrial conditions. On a pilot scale, tests were carried out on samples weighing 15-17 thousand tons of refractory gold-sulphide ores (more than 50% of gold is associated with sphalerite), gold-quartz ores with colloidal gold (74% associated with quartz and pyrite) and gold-silver ores with elevated copper and zinc content (1.5 and 3,5%, respectively), as well as man-caused material lying for 4-5 years of spent quarry material of oxidized gold-silver ores. In the pilot-industrial tests of heap bioleaching of gold-sulfide ores, gold recovery of 84-85% and silver was achieved to 89-90%, the possibility of obtaining high-yield solutions of copper and zinc, suitable for hydrometallurgical processing, from gold-silver ores, and the possibility of obtaining waste with a dump content of valuable components, suitable for deep disposal in the construction industry. When comparing two technologies for processing refractory ores after biooxidation under HL conditions, when 1000 tons of ore processed by the bioreagent were re-milled from a size of 40 mm to 0.1 mm and cyanated under the conditions of the factory process, the same results were obtained for gold recovery (85%) and silver (90%), as with the heap version. The copyrights of the development are protected by a patent.

Jan 1, 2018