Search Documents

By Christian M. Bauer

Modern surface mines are among the world's largest single consumers of diesel fuel. A typical mine site can consume in excess of 200 million liters of diesel fuel per year. Delivered diesel fuel is not necessarily clean. Depending on the mode of transportation, handling practices and local climate, incoming bulk fuel can contain up to 20 mg/L suspended solid contaminants and also significant quantities of free water, which can amount to substantial quantities ? for a typical mine site 200 to 400 kg of dirt per year. Standard on-board fuel filters are not designed to handle high levels of contamination, and most engine manufacturers have specific fuel cleanliness requirements to ensure reliable engine operation. New developments in fuel injector technology, such as high pressure, common rail injectors require even cleaner fuel. In order to ensure reliable operation, it is therefore recommended to control particulate contamination throughout the entire Diesel supply chain - from the bulk storage on mine sites to the injection systems on-board through the use of particulate filtration and liquid coalescence technologies. In this work, the author introduces a comprehensive approach to contamination control for the entire fuel supply chain, and discusses the benefits of using advanced filtration and separation technologies, with a particular focus on the requirements of modern high pressure, common rail (HPCR) fuel injection systems.

Nov 1, 2011

By B. E. Shaw

This paper describes the use of the Free Piston Valve, and a simple hoist brake control system, which has been developed over the last two years, greatly improving the performance of low-pressure brake engines. The basic control system is outlined, with sections devoted to emergency trips and differential braking, and the application of the system to deep shaft hoisting is discussed.

Jan 1, 1966

By Juliana Parreira

The past decade shows record increases in global demand for minerals and metals with an accompanying significant decline in skilled personnel. Mining companies today are examining new technologies to maximize production, reduce costs, and create safer work conditions to deal with this shortfall. Automation of an open-pit mine haulage system is receiving attention as a beneficial option since it provides more consistent and efficient operation of mining equipment, it removes workers from potential danger, it reduces fuel consumption significantly reducing greenhouse gas (GHG) emissions, and it can help optimize vehicle repairs and equipment replacement because of more-predictable and better-controlled maintenance. This paper describes a simulation model under development using the EXTENDSIM software package to examine scale-up issues and constraints of autonomous vehicles in comparison to a manual system. The software can predict and manage Key Performance Indicators (KPIs), such as productivity, safety, cost, equipment failures, fuel consumption, and tire wear under different road and load conditions. By breaking-down the various systems of an autonomous haulage truck and simulating the overall haulage system using a Monte Carlo approach, the model becomes a flexible and powerful tool to use within a mining organization. Direct comparison to a manuallyrun system can be done to show the cost and operational benefits of automation. Project managers can use this tool to guide decision-making about possible application of autonomous haulage trucks at a specific mine site.

May 1, 2010

By C. Robinson

The Diavik Diamond Mine is located in one of the most remote and forbidding places in the world, 220 kilometres south of the Arctic Circle and on the bed of a vast northern lake, Lac de Gras. A single road, built out of ice and crossing frozen lakes, connects the mine with other operations and Yellowknife, the capital of the Canada's Northwest Territories. Diamonds were first discovered in the Lac de Gras region in the early 1990s, and construction of the Diavik Diamond Mine was completed in 2003. Diavik currently mines three kimberlite pipes. Open pit mining has now concluded and all three pipes are mined using underground mining methods. In early 2010, Diavik began mining and processing initial ore from its new underground mine; underground mining operations are expected to continue beyond 2020. The initial mine ventilation system was an exhausting (pull) system with fresh air supplied by a fresh air raise and a main ramp. Return air was exhausted via two raises and a secondary ramp. The system had a total flow capacity approximating 401-411 m3/s. With planned increased production and with changes in mining method, it has been proposed to change the mine ventilation system to a positive (forcing) ventilation system in order to meet projected increases in flow requirements of 566-708 m3/s. Extensive engineering work was developed in order to successfully achieve the changes in system configuration. In the proposed configuration, the main ramp is in an exhaust configuration and exhaust raises are converted to fresh air raise. A number of system implementation options were investigated and phased plans for system execution have been developed. The proposed changes to the ventilation system are substantial and involve extensive construction work. Work was commenced in 2011, each planned phase has been successfully completed to date, and system changes continue today in order to achieve complete system flow reversal and increased flow distribution. This paper details the design of the modified ventilation system and commissioning work which will allow the mine to meet its future production targets.

Aug 1, 2013

By D. B. Dreisinger, A. A. Gunaratnam

A pressure oxidation (POX)-hot cure (HC)-lime boil (LB) process is used in industry to recover silver from refractory gold sulfide ores containing minerals such as pyrite and arsenopyrite. Pressure oxidation is used to oxidize minerals and liberate occluded gold particles. As such, iron goes into solution and under acidic and high temperature conditions often precipitates as basic iron sulfate (BFS). BFS consumes excess lime during neutralization prior to cyanidation. Therefore, a hot cure stage is required to re-dissolve BFS back into solution. BFS re-dissolution consumes acid and produces ferric sulfate. In the presence of silver, these conditions favor the slow formation of silver jarosite. Silver jarosite is refractory to cyanidation, and must be broken down prior to cyanidation. This is done in the lime boil to produce a cyanide-soluble silver hydroxide. A study was conducted to investigate parameters that affect the precipitates that form in each stage of the POX-HC-LB process.

Jan 1, 2017

The hydrometallurgical treatment of copper ores and concentrates continues to be an active field of innovation. The direct extraction of copper from ores containing chalcopyrite is an important development to provide an alternative to flotation-smelting and refining. Jetti Resources (with the University of British Columbia) and the JX Nippon Group have developed process options for chalcopyrite heap leaching. Biological heap leaching developments for chalcopyrite are also continuing in parallel. These direct leaching technologies are also very attractive for arsenical ores. The atmospheric leaching of copper concentrates is an attractive option along with autoclave processing. The Galvanox™ Process is the focus of commercialization by InCoR Galvanox Holdings under exclusive license by the University of British Columbia. The Galvanox™ Process can be used to treat chalcopyrite or enargite containing concentrates to high copper extraction with simultaneous precipitation of arsenic as atmospheric scorodite. FLSmidth has continued development of the Rapid Oxidative Leach (ROL) and associated technologies for chalcopyrite leaching. The Glencore Albion Copper Process using ultra fine grinding of copper concentrates and atmospheric leaching has found application in central Africa. The pressure leaching of copper concentrates continues to be attractive for rapid, complete oxidation of sulfide minerals with high copper extraction and arsenic stabilization of iron-arsenate minerals and precipitates. The Ecometales PLCC project is designed to use high temperature total pressure oxidation for treatment of an arsenical copper concentrate with use of existing copper SX-EW facilities for copper cathode production. The excess acid from the autoclave process will be used to make up the acid demand for associated copper ore heap and dump leaching operations. INTRODUCTION The recovery of copper from ores is dominated by the flotation of copper concentrates followed by smelting—converting and electrorefining. This process has been enabled by the development of froth flotation and progressively made more efficient by advances in smelting and converting technologies.

Jan 1, 2019

By K. Kim

"All milling operations would like to achieve the best possible recovery in combination with the highest achievable throughput. Unfortunately, many operations have problems with low recovery, low throughput or both. In the majority of these cases investigated by the author, the solutions to improve recovery and throughput were simple. The solutions did not include implementation of new technology or major capital, but rather a return to fundamentals. In most cases, problems occurred because the operation was not following their own operating procedures, because the design of the circuit was changed without adequate change management or understanding of the implications of changes, or because basic metallurgical measurements and control were not taken or ignored. In this paper, examples of these problems and their solutions derived from long and varied experience will be discussed. The objective of this presentation is to provide the milling operator with practical and readily implementable solutions to common milling issues to improve throughput and recovery.INTRODUCTION Mill operations can be evaluated by many operating parameters, but the two best indicators are recovery and throughput. These two parameters summarize the wellbeing of an operation. The grade to the mill is also a good indicator, but this is usually controlled by the mine. The best recovery and throughput are achieved through a team work involving operators, maintenance workers and metallurgical staff. The milling operations include many unit operations, such as crushing, grinding, flotation, leaching, carbon in leach, Merrill Crowe, roaster, autoclave and refinery. The tools available to the operations are plant design, process measurements, assays, metallurgical balance, and operating strategy. Twelve real life examples of improvements of recovery and throughput are presented in this paper. EXAMPLE 1: CRUSHING CIRCUIT WITHOUT FINE ORE BIN At this operation plant throughput could not be maintained at a high rate because feed to the mill became coarse during the day. The cone crusher was feeding the ball mill directly. As the day wore on, the gap on the cone crusher would slowly increase, which would cause the product size to increase. This would increase the re-circulating load on the ball mill. The throughput would decrease accordingly. Furthermore, the throughput would decrease more with high frequency of maintenance on the cone crusher."

Jan 1, 2019

By N. D. MacFarlane, D. J. Mossman

"The Nemeiben Lake ultramafic complex, in the Churchill Province of the Canadian Shield in north-central Saskatchewan, is a small I. 6-km circular plug largely composed of high-alumina pyroxene cumulates forming a series of grossly concentric layers of clinopyroxenite, websterite and wehrlite. Minor dunite and gabbro are present in the northwestern part of the pluton.Disseminated primary magmatic pyrrhotite, pentlandite, chalcopyrite, magnetite and chromite occur throughout the intrusion. Sulphides occur in proportions of economic interest in the northern outcrops. A secondary assemblage of fine-grained oxides, sulphides and native metals occurs in serpentinized and uralitized peridotites and pyroxenites. Primary opaque minerals are largely altered to marcasite, violarite and hematite. The ores represent a primary magmatic assemblage extensively modified by metamorphism and, to a lesser extent, by supergene alteration.The complex intruded an Early Aphebian supracrustral succession during the waning stages of the Hudsonian orogeny. The metamorphic peak during Hudsonian time reached middle to upper amphibolite facies, granitized the country rocks and contributed to the partial amphibolitization of the ultramafic pluton.The Nemeiben complex has a number of features in common with the zoned intrusions of southeastern Alaska, including: the diopsidic composition of clinopyroxene, highly magnesian olivines, ubiquitous primary magnetite, relatively high alumina content of clinopyroxenes and the unlikelihood that associated gabbroic rocks are derived from a magma common to the ultramafic rocks. However, at Nemeiben, orthopyroxene occurs as a widespread postcumulus phase and, to a lesser extent, as a cumulus mineral. This fact, together with geochemical data on whole-rock and mineral compositions, indicates a tholeiitic parentage.The nickel-copper deposits of the Nemeiben Lake ultramafic complex are not currently economic, although standard technology for recovery of sulphide minerals in the clinopyroxenite (and websterite) would probably be adequate. Most ore minerals in the altered peridotites belong to the fine-grained secondary assemblage of opaques due to the formation of retrograde hydrous silicates and are probably too fine grained for standard recovery methods."

Jan 1, 1982

By Wenbin Zhang, George W. Poling

"Prior or simultaneous addition of ammonium sulphate can, not only enhance the activating effect of hydrosulphide ions on xanthate flotation of malachite but it can also eliminate possible detrimental or depressing effects of excess residual hydrosulphide . Use of relatively inexpensive ammonium sulphate appears to reduce the consumption of the much more expensive sulphidizing agent for optimal flotation recovery INTRODUCTIONOxidized copper minerals float poorly with conventional thiol-type collectors. This is believed to be due to the nonadherent character of the collector coating, which is readily re- moved by particle abrasion. Rosas and Polingr reported emulsion flotation seemed capable of resisting abrasion during the flotation of non-sulphide copper ores. It appears that the most common flotation technique for oxidized copper minerals comprises sulphidization with Na .S and subsequent treatment by sulphydryl collector. The principles of this method are available . Malghan recently reviewed the studies on the role of sodium sulphide in the flotation of oxidized copper, lead and zinc minerals.It is well known that in the sulphidized flotation of malachite, the activation process depends strongly on the concentration of the sulphidizing agent, i.e., insufficient sulphide gives poor recoveries because of inadequate sulphidization; excessive sulphide also causes poor recoveries due to the depressive effect of the residual hydro-sulphide ions in solution. A major difficulty in sulphidization, especially with a varying feed nature, is to establish and maintain the optimum sulphide concentration in solution. In plant practice, vigorous control of sodium sulphide is required and stepwise addition of the reagent is recommended to improve the efficiency of the process. Soto and Laskowskim have found that malachite, depressed by an excess of sulphide ions, can restore its floatability if air or oxygen is introduced to the pulp. They attributed this to the oxidation of the HS - ions on the surface of the mineral. Jones and Woodcockuvi showed that a sulphide ion selective electrode could be used to optimize the conditions (e.g . amount of hydrosulphide, sulphidization time, flotation time) more readily and precisely than existing methods in the flotation of oxidized copper ores."

Jan 1, 1989

By T. L. Carpenter

"The presence of excessive water in the Gibraltar East Stage 1 pit initiated studies into the ground-water conditions that might be expected in mining the Granite Lake and Pollyanna pits. Hydrologic information obtained from a pump test program in 1974 indicated that deep-well dewatering could be successfully achieved. In 1976, a deep-well dewatering system consisting of eight wells was installed on the periphery of the Pollyanna pit . it has been responsible for a significant decrease in mining costs.This paper presents a brief summary of the engineering principles involved in the design of the Gibraltar dewatering system and the problems encountered in the installation and operation of deep-well pumps. IntroductionGibraltar Mines is an open-pit copper-molybdenite mine located approximately 230 air miles north of Vancouver in the central interior of British Columbia (Fig. I). The property consists of three separate major orebodies; Gibraltar East, Granite Lake and Pollyanna (Fig. 2). Mining commenced during the summer of 1971, in the Gibraltar East Stage 1 pit. The Granite Lake Stage 1 pit was mined from mid 1974 to mid 1976. The Pollyanna Stage 1 pit is currently being mined and the Gibraltar East Stage 2 is being developed for production. This report is intended as an outline of the studies and tests leading up to and including the installation of the Pollyanna pit dewatering system, the problems encountered and the results obtained.GeneralIn the summer of 1973, mining in the Gibraltar East pit progressed below ""daylight"" on the down-hill side and ground water very quickly became a costly nuisance in the day-to-day mining operations. Mining, maintenance and blasting costs reflected these problems. Concern was also voiced about adverse effects of ground water on pit wall stability. This concern later became a reality in the Gibraltar East and Granite Lake pits. A study was initiated to investigate various methods and costs of dewatering the pit areas. The study included in-pit sumps, deep peripheral wells and a drainage gallery system located below the pits."

Jan 1, 1980

By B. R. Casement

"Managing safety on the basis of after-the-fact reaction to accidents, can never be more than partially successful. Injuries will occur as long as the underlying potential for them still exists. Unless unsafe actions and conditions are systematically decreased, no program can have more than a short-term success.The pro-active Bullmoose loss control process, instead, focusses on heightening awareness of work habits, to prevent incidents by reducing their potential.Any safety program will be doomed to failure if the development of safe work habits depends on the safety supervisor or a safety committee. At Bullmoose the focus is on the critical actions out of which losses emerge. The successful application of performance-related feedback is achieved by taking safety, health, and environmental concerns into consideration on every level, and, by doing the right thing in every job done.What is an Exceptional Loss Control Program?If an accident in an organization creates a flurry of interest, resulting in ""cracking down"" on violations for a short period of time then an ""exceptional"" loss control program exists. Unfortunately, exceptional here does not refer to the effectiveness of quality of the program but to the fact that the organization is managing loss control by exception. The degree of management attention in an ""exceptional"" safety program varies over a period of time, remaining low as long as the rate of losses stays within management's acceptable control limit (Fig. I). When the losses rise above this, management becomes motivated to begin ""exceptional"" efforts to manage losses. When the rate falls again to within the accepted limit, efforts to control losses take a back seat.Such a strategy guarantees that losses will be tolerated or ignored as long as the actual rate is below the acceptable limit. Simply to lower the limit would not reduce losses, but would result in an increased number of flurries of management attention to loss control. This ""on-again, off-again"" style of management teaches supervisors and others that basic loss control is not as important as are statistics."

Jan 1, 1993

By J. A. H. Church

MR. J. A. H. CHURCH: The salient feature would seem to be that the thickness of the seam, in our coals at any rate, is the main factor in predisposition to spontaneous ignition. The evidence, incomplete it must be admitted, in the Saskatchewan and British Columbia fields, and complete in the Alberta field to my mind, shows this up very strongly. The German report on the upper Silesian coal fields definitely fixes the critical thickness at 13 feet, the British report goes far beyond this figure by stating that liability to ignition increases with the thickness of the seam over four feet. Before discussing the Alberta fires it would be well to note an error on page 12 -the probable cause of the fire in the Frank Mine should read "Spontaneous near fault. Heating first discovered 1909". Of the six fires attributed to spontaneous ignition all the seams were identical or in excess of the critical thickness mentioned in the German report. If there be any reason in the foregoing it is high time some forethought were taken to adopt some definite system of laying out the workings of such seams not so much on the outcrop districts as with a view to the future operation to the dip. Seams approaching 13 feet in thickness which to date have shown no disposition towards heating during the extraction of the outcrop areas may well cause infinite trouble or indeed total loss when the ventilating pressures increase as increase they must to the dip. This state of affairs can be combatted only by the adoption of a correct system of working and the provision of numerous airways of as large an area as may be compatible with the physical characteristics of the particular seam.

Jan 1, 1923

By Darrell McClarty, Roger Payne, Matt Haggis, Michael Courtin, Deborah Berthelot

"Over forty years of uranium mining in the Elliot Lake region of Ontario (I 956-1996) has resulted in the production of over 300 million pounds of uranium. With the completion of mining activity, Rio Algom Limited and Denison Mines Limited are utilizing progressive environmental technologies and management systems to reduce and manage the environmental risks associated with the 150 million tonnes of potentially acid-generating tailings in nine regional waste management areas. Water covers designed to reduce oxygen entry and thereby significantly inhibit acid generation have been applied at six of the sites with the Quirke site serving as a demonstration site for the Mine Environmental Neutral Drainage program. All five of Rio Algom Limited' s effluent treatment plants are monitored and controlled from a central control station utilizing a Supervisory Control and Data Acquisition (SCADA) system based on ""Fix Dmacs"" technology. Scheduling, auditing and reporting of plant operating and environmental monitoring programs for the entire watershed are controlled utilizing the Regional Environmental Information Management System (REIMS). Proper application of these technologies and management systems facilitates delivery of cost-effective environmental monitoring, care and maintenance programs at these sites and provides tools to demonstrate compliance with all environmental performance criteria.IntroductionCost-effective management of multiple tailings management areas distributed throughout a 35 km watershed requires the application of leading-edge environmental technologies. Long-term monitoring, care and maintenance costs must first be minimized through the application of decommissioning technologies that inhibit acid generation and minimize the release of contaminants from the sites. On-going operating costs must then be controlled through the application of environmental management strategies that optimize the allocation of resources while ensuring compliance with regulatory and Company environmental requirements.Using sites in the Serpent River Watershed as an example, this paper demonstrates the effectiveness of water covers as a decommissioning strategy to inhibit acid generation. In addition, the Telemetered Environmental Operating Control System and Regional Environmental Information Management System are reviewed as examples of the application of environmental technologies to the management of environmental programs."

Jan 1, 1998

By S. Koski, M. Schmalzel, D. A. Jacobson, S. Crosby, P. Cook, M. Mular

"Mining operations, whether new or existing, are constantly looking for ways to maximize production and improve energy efficiency, while keeping the footprint required to a minimum. The Nordberg MP1250 cone crusher was designed with these three goals in mind. A series of side-by-side evaluations comparing an MP1250 to an MP1000 were completed at two Freeport-McMoRan operations. The first evaluation began October 2009 in a tertiary position and the second began March 2010 in a secondary position, where it remains in full production today. Utilizing 25% higher power capacity than the existing MP1000 tertiary crushers, the MP1250 had 29% higher capacity and 17% lower specific energy, adjusted for differences in feed and product size. The MP1250 compared to the existing MP1000 secondary crushers achieved 30% higher capacity at a slightly reduced specific energy, while achieving a finer product.The MP1250’s higher capacity and energy efficiency may have application in many crushing plants. Depending on site specific economic factors, greenfield projects may benefit from a smaller footprint and less ancillary equipment, whereas brownfield projects may benefit from higher capacity or a finer product within the same footprint."

Jan 1, 2012

By George McIsaac

This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development and mining method. Based on practical considerations, maximum rates are set for each zone?s development and production capacity. As for the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum number of development metres per day is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Furthermore, the fixed cost of operating the mine is taken into consideration whenever mining activities take place. Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analysed. What-if scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan.

May 1, 2003

By R. K. Kandasami

"Naturally occurring geomaterials such as sandstone, limestone and other soft rocks, residual soils are composed of a particulates held together through a cohesive matrix, usually composed of argillaceous or siliceous cementing agents. Geo-materials such as these have been reconstituted in the laboratory using ordinary Portland cement in lieu of the naturally occurring cohesive matrix, in addition to using sand particulates. This cohesive frictional granular ensemble is an ideal model material for understanding the mechanical behaviour of transitional geomaterials such as soft rocks. An important consequence of this cohesion that pervades the inter particulate system is the enhanced tensile strength when compared to a purely granular ensemble. The assessment of strength of these soft rocks and cemented sands is often understood in the framework of continuum mechanics, i.e. considering the cemented sand to be a continuum, and performing simple elemental tests such as uniaxial compression or tension tests. A simple model to describe the behaviour of these cemented sands has been to use elements such as springs, sliders, and dashpots in parallel to describe the existence of a cohesive and frictional component of strength (Jiang et al. 2007). In the framework of continuum mechanics, the mechanical response of these cemented sands have been modeled using traditional plasticity theory, for example utilizing variants of the traditional Mohr Coulomb model, Modified cam clay (Sun and Matsuoka 1999) etc. The typical sand models are amended to include the effects of cohesion, as proposed by Lagoia and Nova (1995).The mechanical response of cemented sands is understood to be transitional to the behaviour of a typical particulate assemblage and a quasi-brittle material. However, the effect of length scale in these material systems has not been investigated. This paper presents a series of uniaxial compression experiments conducted on weakly cemented sand specimens of various sizes. The effect of length scale in these weakly cemented sands is investigated through unconfined compression tests."

Jan 1, 2015

By G. L. Palmer

"In 1986, anomalous sampling results for heavy minerals were obtained at various sites in Namaqualand on the west coast of the Cape Province. Drilling in 1987 at Graauwduinen penetrated up to 35 meters of heavy mineral-bearing Tertiary sands which extend several kilometers inland from the coast. The heavy mineral suite includes ilmenite, rutile, leucoxene, zircon and monazite, along with gamet, pyroxene and amphibole. Three deposits are recognized, two of which comprise the resource to be mined by Namakwa Sands Limited, a recently formed Anglo American Corporation subsidiary company.Mineable reserves in excess of 500 million tonnes have been delineated, sufficient to sustain mining for over 35 years at projected production rates. During the feasibility study, on-site investigations included test mining at various sites to assess rnineability and to provide material for metallurgical testing in a pilot plant located at the site. llmenite produced at the mine will be smelted at a new facility to be built at Saldanha Bay. Saleable products comprise titania-rich slag, pig iron, zircon and rutile.During the exploration phase, company environmental guidelines were established and monitored. The feasibility study incorporated a Class 1 Environmental Impact Report, the contents of which were made public following the principles of the Integrated Environmental Management legislation."

Jan 1, 1994

By M. N. Pons, F. Ferrari, V. Houzelot, B. Laubie, A. Bani, Université de Lorraine-CNRS LRGP

"More than 400 plants in the world are able to accumulate nickel in their aerial parts at concentrations higher than 10 g per kg of dry biomass. Then, nickel (Ni) can be recovered from the biomass of these hyperaccumulator plants. Agromining is a chain consisting in growing such plants and recovering metal and has been developed thanks to the combined know-how of agronomy and hydrometallurgy. Plants can be grown on serpentine soils, containing rather high concentrations of Ni, on sterile heaps or on contaminated soils. This crop enables us to extract Ni from secondary resources, and to improve soil quality by lowering its metal content. For example, Alyssum murale can be grown at the field scale in the Balkans, at yields corresponding to 110 kg Ni per hectare.Hydrometallurgical processes have been designed from the lab scale to the pilot scale to produce nickel salts: ANSH (ammonium and nickel sulphate hexahydrate), nickel sulphate, acetate, etc. and so on. These salts are used for surface treatment and in the paint and chemical industry. Ni salts are prepared from ashes, after plant calcination. Processes are based on the conventional methods of hydrometallurgy: acid leaching followed by different precipitation steps. These processes will be presented, as well as the pilot scale design. A life cycle assessment has been performed and clearly shows the environmental interest of this approach as a potential part of an anti-erosion strategy. An economic assessment has proved process feasibility and the final step is the launching of a start-up. At the moment, the approach is widened to other metals (cadmium, cobalt) and rare earth elements (REEs)."

Jan 1, 2016

By Abani R. Samal

The Fe assay values from the diamond drill-holes within a magnetite deposit of magmatic origin are utilized in this study. Only assay data from the unoxidized magnetite mineralization was utilized. The data from the overlying hematite mineralization zone was not used. A threedimensional block model estimated using ordinary kriging (OK) is used for analysis purposes. To estimate the non-linear standard deviations (s) and the confidence intervals (CI) of block estimates a discrete Gaussian variogram model is used in this project. The change-of support coefficient (rv) and the block-support correction are used in the ?block-anamorphosis?. A new calculated value of rv is 0.7283, implies that its influence in the block-anamorphosis is not significant. The CIs are calculated from the block-gaussian variables; then back transformed to the raw values. At 95% probability, the CI for the kriged block estimates of Fe values are calculated using Gaussian kriged estimates of the Fe and the corresponding standard deviations (Gaussian). The results indicate that the block estimates with a high influence from relatively small amount of samples can be identified as high-risk estimates.

Oct 1, 2009

By D. Monder

Fuel cells are promising sources of electrical energy because of their exceptionally high efficiencies and low environmental emissions. Solid oxide fuel cells (SOFC) are high temperature, ceramic electrolyte cells, which unlike most other fuel cells, can work with a variety of fuels besides pure hydrogen, including hydrocarbons and hydrogen sulfide. In this presentation I present the models we have built for a single H2S fuelled SOFC. The goal is to model the electrochemical reaction coupled with mass transfer, fluid flow and current/voltage distribution in an yttria stabilized zirconia electrolyte fuel cell assembly operated between 750 and 850 °C. Two models of the above SOFC are discussed in this work, 1) an algebraic model derived by integrating a one-dimensional model along the thickness of the cell, and 2) a two-dimensional finite element axi-symmetric model. Important physical and kinetic parameters in the 1-D model are fitted using experimental data sets at three different temperatures and reasonable fits are obtained for the data sets at 800 °C and 850 °C. However, the third data set at 750 °C does not give a good fit using this model. We need to apply the curve-fitting to more data sets to investigate it further. The main conclusion that can be drawn from the present study is that the ohmic resistance of the cell is very high. Contact resistances are believed to be the reason behind this although there could be contributions from resistive interphases. The 2-D model also gives reasonable fits to data sets. One of the publications by the laboratory group doing the experimental work in our department presented very interesting data that shows the cell performance being a strong function of fuel flow-rate. We want to model this behaviour and will have to depend on the 2-D model as the 1-D model does not have flow-rates as parameters.

Jan 1, 2005