Search Documents

By George J. Thompson

This pa per deals with the internal characteristics of steel and its response under cold northern temperatures. General maintenance procedures and specific repair techniques are covered.

Jan 1, 1973

By M. Abdollahi, M. R. Khalesi, Y. Kianinia, A. Khodadadi Darban

High cyanide consumption during the processing of gold ores with high sulphide minerals can make the typical cyanidation uneconomic. Also cyanide is a toxic material and environmental concerns of cyanide compounds are serious. Optimization of cyanide consumption requires a methodology to estimate the amount of exposed cyanicides, the kinetic of their dissolution and estimation of formation of cyanide complexes which consume the free cyanide. In this paper, a methodology to estimate cyanide consumption by modeling the minerals and gold leaching kinetic based on a liberation model and speciation of all possible cyanide related species in the solution is presented. The results showed that this methodology could successfully estimate the cyanide consumption based on mineralogical data with very lower number of parameters compared to empirical models present in the literature, while it offers the prediction of formation of all cyanide complexes which could be used for optimization purposes.

Jan 1, 2017

By K. S. Coley, M. A. Rhamdhani, G. A. Brooks

Interfacial phenomena in high temperature reactions such as between iron alloy and slag is well documented but not fully understood. It is believed that a gradient of oxygen concentration plays an important role to the occurrence of such phenomena. This article describes the results from the continuation of the study of interfacial phenomena between Fe-Al alloy droplets and CaO-SiO2-Al2O3 slag. Materials characterization techniques involving microscopic observations, depth profiling, bulk, point analysis and were carried out. The roles of oxygen as well as other factors that contribute to the interfacial phenomena were evaluated. The results and their implications to steelmaking will be discussed.

Jan 1, 2004

By E. Burdukova

Long-chain primary amines are utilized as collectors in potash ore flotation. Krafft temperature of long-chain amines in brine is about 100 °C, and this makes such amines practically insoluble in brine at room temperature. When dodecylamine, melted at 70 °C and dispersed in hydrochloric acid (or acetic acid) aqueous solution, is added to a KCl-NaCl saturated brine at room temperature, the amine precipitates. The experimental results demonstrate that the precipitating amine hydrochloride particles are selectively abstracted by KCl particles, but not by NaCl particles.

Jan 1, 2009

By K. Ohto, B. B. Acihikari, H. Kawakita, M. Gurung, S. Alam

Two kinds of adsorbents were prepared from persimmon tannin extract to investigate their adsorption behavior of metal ions from hydrochloric acid solution; one was prepared by treating with concentrated sulfuric acid while another was prepared by immobilizing functional groups of quaternary amine. The former adsorbed only gold(III) and its maximum adsorption capacities was evaluated as high as 1510 g/kg while the latter adsorbed not only gold(III) but also palladium(II) and platinum(IV), the maximum adsorption capacities of which were evaluated as 820, 89 and 101 g/kg, respectively. For both adsorbents, practical adsorption of base metals was not observed.

Jan 1, 2011

By T. A. Apelt, B. J. Elliot

"In September 1993, the flash furnace at Kalgoorlie Nickel Smelter, KNS, was brought off line after almost 12 years of operation. This is a record campaign life for a flash furnace. The furnace was' totally rebuilt and the capacity of the plant increased from 540 000 tpo to 750 000 tpa of concentrate throughput. The throughput increase was' achieved through the construction of a 525 t/day oxygen plant and upgrading of various plant ancillaries. A number of significant design modifications were also built into the flash furnace and oxygen enrichment was implemented in the operation of the Peirce-Smith converters.This paper discusses the rebuilding of the flash furnace and design modifications made to furnace equipment and ancillary plant. Some preliminary post-startup operating data are presented.IntroductionIn September 1993, Campaign 6 of the flash furnace was concluded and the furnace brought off line for rebuilding. The campaign length was almost 12 years and set a new record for campaign length. Planning for the rebuild took place over the last five years of the campaign. A number of modifications to the design of the furnace and the ancillary plant were planned to coincide with the furnace rebuild. The furnace was rebuilt and recommissioned in 70 days. The increased plant capacity of 750000 tpa has been achieved by the construction of a 525 t/day oxygen plant and modifications made to ancillary plant which centred around increased p~ control, efficiency and hygiene. This paper examines the development and implementation of the modifications made to the furnace and ancillary plant. Preliminary post-shutdown performance data are presented."

Jan 1, 1995

By J. A. Finch, M. Mimezami, M. S. Hashemi A.

The adsorption of magnesium and calcium ions on sphalerite and pyrite is discussed. These ions are common in process water and often considered be detrimental in sulphide flotation. The study attempts to characterize the adsorption mechanism, which has been less studied than the oxide system. Generally for oxides metal ion uptake occurs when cations are hydrolyzed. Our findings reveal that magnesium and calcium adsorb on sulphides at pH below hydrolysis, but adsorption is not chemical. At higher pH, charge reversal occurs that does correspond to presence of hydrolysis products. Advances

Jan 1, 2009

By C. Pichler, J. Antrekowitsch

During the production process of steel and other metals a lot of different by products are generated in high amounts. Some of these residues are recycled to recover valuable metals like zinc, lead, copper and others. Especially the treatment of steel mill dust presents a great challenge. The need for new technologies can be seen in the wide range of available recycling concepts for steel mill dust treatment, however most of them have significant disadvantages. An example is the waelz process, which generates about 650 to 700 kg slag during the treatment of 1000 kg steel mill dust. This so called "waelz slag" must be dumped in the most cases. To avoid a landfilling all generated products must be able to get reused in another application. A so called "Zero Waste Process" can be reached with the "2SDR Process" (Two Step Dust Recycling Process), in which the dust is treated on an liquid iron bath generating cast iron, inert slag and zinc oxide. These products have a further usage and can also be sold. The paper focuses on the process development through trials in lab and technical scale up to planned pilot scales, with an accompanying characterisation of the generated products were done.

Jan 1, 2014

By Liguang Wang

The froth phase in flotation has received much less attention than the pulp phase despite the fact that froth stability plays an important role in determining flotation performance. Froth stability is largely determined by the stability of thin foam films, which in turn has a strong correlation with the critical rupture thickness (Hcr) of the films. In the present work, a new approach to predicting the Hcr values of thin foam films in flotation froth phase was proposed and examined. The Hcr values were calculated using an advanced capillary wave model with input parameters being surface tension, film radius, capillary suction pressure, and intersurface force. The intersurface force was estimated by using the Stefan-Reynolds lubrication approximation to fit the measured thinning rates of single foam films formed in a Scheludko ring cell, where the film radii were less than 50 microns and were kept constant during the film-thinning process. A comparison between the predicted and experimental Hcr values was made for the films with the use of sodium chloride as background electrolyte and in the presence of various frothing reagents such as methyl isobutyl carbinol (MIBC), polypropylene glycol with an average molecular weight of 400 (PPG400), and sodium dodecyl sulphate (SDS), at different concentrations and film radii. It was found that the model correctly predicted the trends of Hcr-versus-concentration and Hcr-versus-film radius curves. Moreover, the predicted Hcr values matched well with the experimental ones of the foam films containing either SDS or PPG400. For the foam films containing MIBC, however, the model overpredicted the Hcr values. The reason for this discrepancy was discussed.

Jan 1, 2016

By Deng Yang-wu, Zhang Yan, Chen Chun-fei, Luo Xian-ping, Luo Cai-gui

This paper summarizes the ecological imbalance status of abandoned rare-earth element (REE) mines in southern China. These include large areas of vegetation damage, serious water and soil erosion, landslides, mudslides, heavy metal pollution, water pollution, soil contamination, and fluorine pollution. The causes which lead to the ecological imbalances at abandoned rare-earth mines are analyzed, such as: the inadequacies of using vat leaching, heap leaching, and in-situ leaching processes to extract REE resources; low mineral thickness and low grade of REE ore; and low utilization rates of the resource. Southern ionic REE resources are not fully integrated, with limited access and ineffective supervision of REE mining by relevant departments. The ecological recovery research for ionic-type REE mines is lagging behind, and there is no deployable ecological restoration method for REE wasteland. In the end, the following suggestions are made to improve the ecological imbalance status of rare-earth mine in southern China: develop new rare-earth extraction processes, accelerate the integration pace of REE resources, increase investment in ecological restoration research in rare-earth wasteland, and so on.

Jan 1, 2014

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By K. C. Corin, M. S. Manono, J. G. Wiese

Depressants play a crucial role in the flotation of PGM bearing ores as they prevent naturally floatable gangue (NFG) from reporting to the concentrate. This action is regarded as critically important because less dilution of the concentrate means lower costs for downstream processes. However, abnormal water conditions (such as high concentrations of ions) in the flotation system can modify the selectivity of these depressants. It is well known that the existence of selected electrolytes in water can alter the behaviour of some polysaccharide depressants by enhancing their adsorption onto gangue minerals and thereby prevent naturally floatable gangue from moving into the froth phase. Concurrently these same electrolytes may enhance frothability, owing to their stabilising effect on the bubbles within the system. Plant water at various ionic strengths was investigated against depressant type and dosage in order to understand electrolyte-depressant interactive effects during the flotation of a Merensky ore, using entrainment, rate of NFG recovery, and total gangue recovery as proxies. The study showed that the rate of NFG recovery per unit mass of water decreased with increasing ionic strength at all dosages, however the total amount of gangue reporting to the concentrate increased with increasing ionic strength at all depressant dosages. Thus, this paper attempts to consider the effects of both ionic strength and depressant dosage as individual factors within flotation. It further looks to investigate whether any interactive effects exists between these two factors when considered simultaneously.

Jan 1, 2016

By H. Clare Horwood

"In the Little Long Lac-Sturgeon River area of Thunder Bay district, Ontario, most of the known ore deposits occur in fractures, shear zones, and zones of brecciation, in folded sedimentary rocks . In two or three instances, however, deposits occur in Keewatin greenstones and in later granitic rocks of probable Algoman age.The principal regional features in the area are the long narrow bands of Keewatin volcanic rocks and Timiskaming sedimentary formations that extend east from lake Nipigon to Long Lac, a distance of about 65 miles. The belts continue to the east for many miles beyond Long Lac and probably for some distance to the west under the waters of lake Nipigon. They are intruded in places, particularly in the north, by large masses of diorite, granodiorite, and granite. Small intrusive masses of diorite and porphyry also occur in many localities throughout the area.The Little Long Lac-Sturgeon River mining area is the youngest camp in Ontario and has been in production only since 1934.The district is readily accessible from the branch line of the Canadian National railway between Longlac station on the main line and Port Arthur, and from the Trans-Canada highway No. 17. Both these means of communication traverse the area in a general east-west direction parallel with the principal structural trend of the rocks of the region.In the Little Long Lac section discoveries were made by W. W. Smith in 1931 (Hard Rock property) , by T. A. Johnson in 1932 ( Bankfield property) , by T. A. Johnson and T. Oklend in 1932 (Little Long Lac property) , by F. MacLeod and A. Cockshutt in 1933 (MacLeod-Cockshutt property) , and by George and Frank Papineau in 1935 (Hutchison Lake property).In the Sturgeon River section discoveries were made by Powers and Silam in 1925 (Northern Empire property), T. A. Johnson in 1931 (Dik-Dik property) , and by Russell and James Cryderman in 1935 and 1936 (Sand River and Leitch properties)."

Jan 1, 1954

By Diego L. Romero, Joy P. Romero

"IntroductionMinerals may be classed broadly as ferromagnetic (magnetite for example), as paramagnetic (attracts to regions of magnetic field convergence) and as diamagnetic (attracts to regions of magnetic field divergence). High-intensity separators are not necessary to separate ferromagnetic minerals from other classes. Rather, low-intensity units that generate fields below 5000 gauss are adequate for this purpose. However, paramagnetic minerals, such as ilmenite, with high magnetic ""attractability"" require fields of up to 10 000 gauss; those with low attractability may require even higher fields. Table 1 shows approximate ranges of field intensities necessary to separate ferromagnetic and paramagnetic minerals from minerals of lower attractability, along with the force with which they are attracted relative to iron in a standardized magnetic field.Uniform magnetic fields, not useful for separators, are generated between flat parallel surfaces; non-uniform fields, useful for separators, arise when at least one of the surfaces is of irregular shape. The diagrams below show how magnetic lines of force align relative to north and south poles.If a particle is placed in a uniform field, it feels no displacing force unless the particle distorts the applied field assymmetrically. This is not the case in non-uniform fields which are required for magnetic separators.Magnetic fields can be generated by permanent magnets (low intensity), by electromagnets (medium and high intensity) and even by superconducting coils (100 000 gauss fields and higher), although the latter are not as yet useful in production environments .The magnetic force of attraction per unit of mass, that acts on a paramagnetic mineral such as hematite, increases in proportion to the strength of the field . Unfortunately, the highest fields attainable with electromagnets is of the order of 20 000 gauss. Fortunately, the gradient of the fie ld (that is, the degree of convergence of magnetic lines of force) is important, because the attractive force per unit mass is proportional to it also . This can be stated:"

Jan 1, 1989

By Craig Haase

A. Introduction

Jan 1, 2003

By R. Tessier, R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. The paper presents findings in the on-going testing of various sizes and shapes of grinding media. Breakage rates are used as an aid to assess the effect of grinding media. Results of empirical and phenomenological analyses demonstrate the importance of adequate selection of media sizes on the milling operation.INTRODUCTIONBrunswick Mining and Smelting operates one of the world's largest lead and zinc mine near Bathurst, New-Brunswick. The No. 12 ore body is an extremely fine grained volcanogenic massive lead, zinc, copper, silver, iron sulphide body between two metamorphosed sedimentary and felsic volcanic rock units. Pyrite content is about 60% with 20% non-sulphide minerals, mainly silica and chlorite. The operation is currently processing 10,500 tonnes of ore per day in conventional crushing, grinding, differential flotation and dewatering circuits. Details on the circuit can be found elsewhere (e.g. Hendriks and Ounpuu, 1985; Grant et al., 1991).The mill has operated for more than 25 years and despite the past milling experience, there has been much disagreement as to the required grind size. Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37µm) and averaged slightly over 71%in1992. Results from mineralogical analysis (Petruk and Schnarr,1981; Coleman, 1988), Brunswick metallurgical laboratory (Grant et al., 1991; Shannon et al., 1992) and Lakefield pilot plant tests (Hendriks, 1984; Hendriks and Ounpuu, 1985) clearly indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15-25µm range."

Jan 1, 1993

By J. W. Coetzee, H. E. Deist

Carbon-in-pulp (CIP) and Carbon-in-leach (CIL) processes are used extensively in the gold mining sector to recover aurocyanide from solution. This paper discusses the modelling of these operations, using various simplifying assumptions, in order to simulate the effect of changing operating conditions on the dynamics of the system. It is assumed that the adsorption and leaching rates are a function of concentration difference between the source phase and recipient phase. The simulation was set up using Matlab's Simulink interface. Plant variables are solved using a medium scale Newtonian search algorithm in Matlab, where the differences between the actual and predicted plant outputs are minimized on a continuous time-line.

Jan 1, 2005

By D. Neely

As Saskatchewan potash mines grow in age and size, mining reaches greater depths.  The stress-relief design principals which were empirically derived at shallower depths are beginning to show fault.  Nutrien Vanscoy Potash has began to encounter new ground support and panel design challenges which were previously had negligible effect.  While the initial reaction was to reduce extraction and implement distance buffers between operating machines, it eventually became clear that these would only provide short term relief and that in order to continue safely and efficiently mining broad areas, a fundamental change in the mine design would provide the long-term protection required.  Presented is a case study with an overview of the challenges encountered at Vanscoy Potash in areas of greater depth along with an account of the design changes considered, implemented and recommended for future success. 

May 4, 2025

By W. L. Stuewe

The Dominion Steel and Coal Corporation requires enormous quantities of bricks each year for its Sydney steel plant operations. Clay brick of all types are purchased, while silica brick is made in the Company's plant at Sydney. A description of this plant was given in a paper presented by H. B. Gillis and F. C. Morrison at the 1938 Annual General Meeting of the Institute. The rock used to make silica brick was for years obtained from a quarry at Leitches Creek, about eighteen miles from Sydney. Due to the gradual deterioration of this deposit, the Corporation was forced to look for other sources of supply. In 1945, the problem was presented to the Nova Scotia Department of Mines and, through the efforts of Dr. A. E. Cameron and Mr. J. P. Messervey, an examination was made of a silica-rock deposit some six miles northwest of Yarmouth, N.S. Preliminary samples proved satisfactory, and arrangements were made with the Department of Mines to ship to the steel plant at Sydney a fifty-ton car load for the purpose of further testing. Brick made from this sample shipment stood up very well in the furnaces. At the same time, two hundred and fifty tons of silica rock from a deposit at Lac Bouchette, Que., were purchased from the Industrial Silica Corporation, and brick made from this rock also was found suitable for our requirements. Comparative transportation costs, however, led to a decision to open the Yarmouth deposit. The silica rock, or quartzite, of this deposit outcrops at Chegoggin point along what is known as the 'Pembroke shore', a northerly trending section of the coast-line at the extreme southwest of the Province, in Yarmouth county. The country here is fairly flat, with elevation averaging about twenty feet above high tide, and is for the most part mantled by a growth of brush and some scrub trees, chiefly small fir. Bed-rock is generally concealed beneath three to four feet of clayey soil, but scattered outcrops of the quartzite indicated that a band of this rock, some 260 feet wide, extended inland in a northeasterly direction from Chegoggin point at least to Utleys lake, a distance of about three miles.

Jan 1, 1947

By Frank Ebbutt

In this paper it is proposed to point out certain structural factors that; have an important bearing on gold deposition. The subject will be treated; more or less generally. Although the writer has had access to a great many; of Canada's gold mines he does not wish to take the liberty of discussing; details of any particular mine or mines; the aim will be to discuss controls; that are evident in many places.

Jan 1, 1954