Search Documents

By Richard Dawson

Increasing global demand for coking coal has initiated several new coal mine developments in northeast BC. These developments are able to take advantage of the currently under utilized infrastructure that was put in place during the 1970?s and 1980?s for the Quintette and Bullmoose coal mines; which includes the Town of Tumbler Ridge, a 1,000km rail line to the coal terminal at Prince Rupert and a road system providing highway access to the town site. Coal within the two foothills regions of BC (north-east and south-east) is mined by open pit truck/shovel methods. Optimized mine plans require a thorough understanding of Rocky Mountain structural geology, attention for access in steep terrain, and a related understanding of the geotechnical conditions that control the stability of pit slopes and waste dumps. Thus there is a requirement to properly integrate mine planning with geotechnical engineering considerations. Many of the technical issues are well understood from experience during the past 30 years of Western Canadian coal mining. The challenge is to ensure that the mine plans are able to take full advantage of these lessons learned. The paper will focus on mine planning and geotechnical design issues to do with high angle-of-repose waste dumps and steeply bedded footwall slopes to illustrate the advantage of properly recognizing the important stability control issues during the early stages of engineering evaluations. Case histories from the existing and planned coal mining operations will be presented.

May 1, 2006

By J. W. Senn

A magnesium alloy modeled after commercial alloy WE54 was thermomechanically processed and characterized to understand the mechanisms by which its texture can be randomized, as reported by Ball and Prangnell [1]. Samples were deformed in plane strain compression to prescribed strain levels at temperatures high enough to prevent cracking and then recrystallized. The deformation texture is very similar to that observed after plane strain compression (e.g., rolling) of other Mg alloys, such as common AZ31. However, the texture can radically evolve during recrystallization. Annealing above the precipitate solvus temperature results in a nearly random recrystallization texture where the initially strong basal texture is completely eliminated. Annealing below the solvus temperature produces a recrystallized texture similar to conventional Mg alloys, i.e., a weakened basal texture. If this same material is then annealed above the solvus to promote grain growth, a randomized texture evolves, which is similar that of samples simply recrystallized above the solvus. It is hypothesized that a sort of preferred growth mechanism, whereby grains with random orientation grow faster than those with the original basal texture, contributes significantly to the texture randomization observed in wrought magnesium alloys containing rare earth elements.

Jan 1, 2006

By J. A. Finch

Solvent-coated air bubbles in the Air-Assisted Solvent Extraction (AASX) process achieve the dual role of high solvent specific surface area and ease of phase separation. The thickness of the solvent film is of fundamental interest but difficult to measure directly in the process itself. As an approach interferometry (in the UV-vis region) was used to measure the time dependent thickness of a film formed by blowing an air bubble in kerosene-based solvents. The film was stabilized by the presence of 1.5 ppm silicone oil, as employed in AASX. The film appears to comprise two layers; an outer "free" layer of almost constant thickness and an inner "bound" layer which decreased in thickness with time. The bound layer is considered relevant to AASX. For a 20 mm diameter bubble blown in LIX/kerosene solvent the initial thickness was ~ 3 um which decreased over 10 minutes to a final rupture thickness of 500 nm. The bound layer thickness and time to rupture decreased with decreasing bubble size. Correspondence to prior indirect estimates of solvent layer thickness is examined.

Jan 1, 2006

By Asanga S. Nanayakkara

The surface deformations induced by reservoir dilations can be measured using tiltmeters and these measurements can be used to infer reservoir level volume changes by solving an inverse problem. Preferred approach to solve such an inverse problem is to consider more tiltmeter measurements than the number of unknown variables considered in the inverse problem. However, sufficient number of measurement points is not always available due to economical and practical issues. This paper proposes a new approach to circumvent this problem. The new approach entails generation of pseudo surface deformation data by curve fitting tiltmeter measurements using a mathematical function, which delineates three-dimensional characteristics of surface deformation profiles. Then a three-dimensional inverse problem is solved using pseudo surface deformation data. This method is useful in inferring reservoir volume changes with high areal resolution when the number of available measurements is not sufficient to acquire the desired areal resolution.

Jun 1, 2012

By M. J. Nicol

The leaching of gold with thiosulfate solutions in the absence of ammonia and copper ions was investigated using electrochemical and kinetic methods. In sodium thiosulfate solutions, the electrochemical oxidation of gold was hindered and the leaching rate using pure oxygen as the oxidant was very slow. It was found that the addition of a small amount of thiourea or formamidine disulfide to the thiosulfate solution greatly enhanced the oxidation of gold. However, the enhancement to the overall dissolution of gold using dissolved oxygen as the oxidant was limited. This was attributed to the fact that the oxygen reduction process was unaffected by the additives and remained slow, which limited further improvement to the overall kinetics. An alternative oxidant, the ferric EDTA complex having a reduction potential of approximately 0.12 V, was found to be promising. The cathodic reduction of ferric EDTA was fast and reversible at neutral pH. While the ferric EDTA complex was effective in oxidizing gold, it did not appear to significantly oxidize thiosulfate. A thiosulfate solution containing thiourea and ferric EDTA has been shown to quickly dissolve gold in the form of a powder as well as from gold ores. In the leaching with the ores high gold recoveries of above 90% was achieved with the best performance obtained in neutral solutions (pH 6-7).

Jan 1, 2005

By J. P. Grieco, F. W. Grieco

"Manufacturing of Jaw CrushersOriginIn 1858 Eli Whitney Blake invented the first successful mechanical rock breaker-the Blake-type jaw crusher. Blake adapted a mechanical principal, the powerful toggle linkage system used to transform rotating motion and energy into oscillating mot ion and tremendous compressive forces. Today these same principals apply and the basic Blake-type jaw crusher is one of the leading machines of its class for heavy duty primary crushing service.In 1881 Philetus W. Gates patented a design for a crusher, the forerunner of the modern gyratory crusher which dominated the field from the late 1800s to the early 1900s. In 1910 the largest gyratory crushers built had 48-inch openings. However, about this time the jaw crusher came to life when the Power and Mining Machinery Co. built an even larger sized opening crusher-a giant 84-inch by 60-inch jaw crusher for a trap rock quarry in Pennsylvania. A 24-inch gyratory crusher became the ideal sized secondary machine for this size jaw. From that time on jaw crushers were looked on favourably as primary breakers and lines were brought up to date to parallel the already developed gyratory lines.FunctionMost heavy duty Blake-type jaw crushers work basically the same way. They are ruggedly designed and capable of crushing material in some cases in excess of 80, 000 p.s.i. compressive strength. They are very simple machines with few moving part s and, with the exception of replacement of renewable parts, are relatively maintenance free. It is quite common to have these machines in product ion for 20 to 30 years. The following will de scribe how these machines work. Large-diameter high-inertia flywheels which are connected to the main eccentric shaft, rotate inside a connecting rod type mechanism called a Pitman. It transforms rotating motion into vertical oscillating motion. This vertical motion is in turn transformed into reciprocating mot ion by means of a system of 2 toggles, each connected to the Pitman. The rear toggle is connected to the fixed rear head, and the front toggle is connected to the swing jaw which is hinged at the top of the crusher. With each rotation of the eccentric shaft the swing jaw opens and closes on rock which is fed into the crusher chamber, crushing the rock in a series of bites. These bites, or strokes as the y are called, usually vary between 1/2 inch to 1 1/2 inch at speeds of 120 to 200 strokes per minute. The reduction ratio of feed input to discharge is usually about 8 to I. Output capacities can vary from 100 tons/hour to 1200 tons/hour depending on the size of machine and its discharge opening. Horsepower requirements can vary from 75 hp to 400 hp.The entire crusher chamber is lined with replaceable 14070 manganese steel liner plates. This material is ideally suited for the job since it hardens as it wears during crusher operation. Manganese is also used in the high wear areas at each end of the toggle plates."

Jan 1, 1985

By J. P. Grieco, F. W. Grieco

"Manufacturing of Jaw CrushersOriginIn 1858 Eli Whitney Blake invented the first successful mechanical rock breaker-the Blake-type jaw crusher. Blake adapted a mechanical principal, the powerful toggle linkage system used to transform rotating motion and energy into oscillating mot ion and tremendous compressive forces. Today these same principals apply and the basic Blake-type jaw crusher is one of the leading machines of its class for heavy duty primary crushing service.In 1881 Philetus W. Gates patented a design for a crusher, the forerunner of the modern gyratory crusher which dominated the field from the late 1800s to the early 1900s. In 1910 the largest gyratory crushers built had 48-inch openings. However, about this time the jaw crusher came to life when the Power and Mining Machinery Co. built an even larger sized opening crusher-a giant 84-inch by 60-inch jaw crusher for a trap rock quarry in Pennsylvania. A 24-inch gyratory crusher became the ideal sized secondary machine for this size jaw. From that time on jaw crushers were looked on favourably as primary breakers and lines were brought up to date to parallel the already developed gyratory lines.FunctionMost heavy duty Blake-type jaw crushers work basically the same way. They are ruggedly designed and capable of crushing material in some cases in excess of 80, 000 p.s.i. compressive strength. They are very simple machines with few moving part s and, with the exception of replacement of renewable parts, are relatively maintenance free. It is quite common to have these machines in product ion for 20 to 30 years. The following will de scribe how these machines work. Large-diameter high-inertia flywheels which are connected to the main eccentric shaft, rotate inside a connecting rod type mechanism called a Pitman. It transforms rotating motion into vertical oscillating motion. This vertical motion is in turn transformed into reciprocating mot ion by means of a system of 2 toggles, each connected to the Pitman. The rear toggle is connected to the fixed rear head, and the front toggle is connected to the swing jaw which is hinged at the top of the crusher. With each rotation of the eccentric shaft the swing jaw opens and closes on rock which is fed into the crusher chamber, crushing the rock in a series of bites. These bites, or strokes as the y are called, usually vary between 1/2 inch to 1 1/2 inch at speeds of 120 to 200 strokes per minute. The reduction ratio of feed input to discharge is usually about 8 to I. Output capacities can vary from 100 tons/hour to 1200 tons/hour depending on the size of machine and its discharge opening. Horsepower requirements can vary from 75 hp to 400 hp.The entire crusher chamber is lined with replaceable 14070 manganese steel liner plates. This material is ideally suited for the job since it hardens as it wears during crusher operation. Manganese is also used in the high wear areas at each end of the toggle plates."

Jan 1, 1985

By K. Thuro, H. Käsling, F. Menschik

"With increasing data volume, due to enhancing requirements for ground investigation programs for large construction projects, the demand for more efficient filing systems is more and more growing. Depending on the project we also have to use flexible systems to cope with varying data out of different lab and field tests.The chair for Engineering Geology at TUM is developing a web-based database solution to handle all project relevant data in a more appropriate way. We aim to optimize our data management to achieve a fast and easy way of collecting, documenting and analyzing our gained data. The second objective is to provide an easy access to our data for project partners across broadly distributed locations.This Database system consists of a PHP web interface and a MySQL database core. The current setup allows an online access via Internet (www). We are able to grant and constrain access to all data or only arrays of data with our user management system to guarantee the safety of project data and respect all rights and proprietorship. The database system is of modular design and consists of the following three base modules: module of general project data, module of laboratory data and user management module. At the current stage we are able to save and work with all usually generated specific values from unconfined compressive strength tests, brazilian tensile strength tests, point load tests, CERCHAR and LCPC abrasivity tests and ultrasonic tests. The user is able to perform a simple statistical analysis within our database (e.g. average calculation of one sample) and export data as csv or xls files for further analysis.For specific questions within projects we are able to deploy and integrate further modules in our database system. At this moment, we are developing an add on to use this database for different drill test analyses. One of the tools correlates drilling performance and drill head wear measured in the field with rock mechanical properties, and extrapolates the data to estimate the performance and wear in new projects. Today we are managing 90 projects with 550 samples and almost 1350 lab tests with the base module.In our contribution we aim to demonstrate an efficient way of data structuring using a relational database for laboratory and field testing data."

Jan 1, 2015

By Denni Nikols, Farrukh Z. Khan

"Highvale Mine, located at Wabamun, Alberta, produces thermal coal for TransAIta's Keephills and Sundance generating plants. Overburden stripping in the mine is conducted by draglines which normally operate on top of the overburden bench. In certain areas oj the mine, however, these overburden benches are susceptible to slope failure. In these areas, due to safety considerations, the draglines are utilized in the less productive chop-cutting mode, supplemented by mobile equipment where the bench height exceeds the dragline chop-cutting limit. This paper proposes maintaining the draglines in their normal digging mode through areas of unstable or jailed overburden, by utilizing a dragline carried toe buttress 10 ensure adequate bench stability. The data requirements and methods of slope analysis to design a toe buttress across an unstable highwall area are examined in rigorous detail. INTRODUCTIONLocationHighvale Mine is owned by TransAlta Utilities Corporation and operated under contract. It is Canada's largest coal mine with an annual coal production in excess of II million tonnes. The mine is located approximately 80 km west of Edmonton on the south shore of Wabamum Lake (Fig. I) and production is currently provided by three pits 02. 03 and 04 (Fig. 2). The entire coal production is consumed at the nearby Sundance and Keephills power generating plants.ScopeThe mining operation at Highvale Mine has had occasional slope stability failures of its high wall overburden bench. This paper examines one such failure which occurred in the summer of 1983 at Pit 03. In addition to an investigation of the failure, Terracon was asked to recommend mine operation procedures which would minimize the impact of these slide zones on dragline productivity. A method of removing the failed material by utilizing the dragline in its normal digging mode is designed. The method's advantages and disadvantages as well as the required support procedures are reviewed."

Jan 1, 1989

By P. M. Pearson

This paper describes the principles ()f systems engineering and their application to the various transport problems confronting the mining industry. The organization of mining operations into sub-system design problems is explained.

Jan 1, 1970

By A. Roy MacLean

This paper outlines the changes in modern-day coal mining that have been brought about by the increased cost of labour and the use of new and highly efficient equipment. In the latter category are mentioned the ramp-plate, the Bretby cable carrier, armoured face conveyors and the shearer-loader. Greater productivity and increased safety are emphasized.

Jan 1, 1969

By F. Q. Su

Underground Coal Gasification (UCG) is a promising environmentally acceptable clean-coal technology. A typical UCG system has two wells drilled from the surface into a coal seam with some separation of injection from production. The wells are connected underground by various linking techniques. After creating a combustion reactor in an underground coal seam, air and oxygen flow through the injection well. Heat energy and gases are collected from the production well. As gasification progresses, the combustion reactor is moved along the linking hole. Using this process, the fracturing activity inside the coal seam serves an important role for enlargement of the gasification zone because the surface area oxidization increases continuously by coal cracking. For effective coal gasification, fracturing activity must be controlled. Moreover, excess fractures inside the coal seam and surrounding rock can induce gas leakage, underground water contamination, subsidence, etc. Therefore, monitoring and control of fracturing activity in underground areas constitute key technologies for efficient and safe UCG. To monitor fracturing activity, we conducted laboratory and small-scale field experiments of UCG using acoustic emission (AE) measurements. UCG model tests were conducted for linking and coaxial types UCG models. Coaxial UCG systems are compact and are anticipated for application in underground coal seams having a complex geological structure. The UCG model consists of a coal block molded in a steel canister (20 liter capacity) with heat-resistant mortar, with a linking hole or a coaxial-hole passing through the coal block. During coal combustion, coal temperatures, production gas contents, and AE activity were monitored under the control of injection-air and oxygen flow rates. Results show that the combustion propagated inside the specimen along the linking hole. Many AE events were generated during coal combustion. The AE activity was related closely to temperature changes inside the coal block. This AE generation apparently results from crack initiation and extension around the coal combustion area under the influence of thermal stress. However, comparing the results from UCG models of linking and coaxial types, the gasification of the linking type model showed an average calorific value as high as 11.3 MJ/m3. The coaxial type yielded an average calorific value of produced gas as only 5.79 MJ/m3. In the coaxial type of UCG model, the combustion region was limited to the area around the coaxial hole. The AE activity was lower than in the linking type model. For small-scale UCG field experiments, linking and coaxial types were tested at an open pit coal mine in Hokkaido, Japan. Using a linking type UCG, 58.2 kg coal was processed in 39 h, with the calorific value estimated as 11 MJ/m3. However, the coaxial type UCG processed 7.0 kg coal in 9 h, yielding an estimated calorific value of 6.0 MJ/m3. These tendencies resemble those of results of laboratory UCG experiments. Results of these experiments demonstrate that AE monitoring is a useful tool to evaluate combustion reactors for efficient and safe UCG systems. To develop a coaxial UCG system, results show that fracture control around combustion reactors is indispensable.

Aug 1, 2013

By S. Amira

In the last two decades, many new creep-resistant magnesium alloys have been developed for high temperatures applications. Their mechanical performance and corrosion behaviour were reported for various experimental conditions. However, these conditions often led to uneven comparison basis. In the present study the microstructure, mechanical properties and corrosion performance of four of these newly developed creep-resistant magnesium alloys were systematically compared. Specimens were obtained from experimental box-like components that were die-cast and thixocast in comparable conditions. Their mechanical and corrosion properties were compared using similar testing conditions. Results show that the creep resistance, strength and impact resistance of specimens are comparable but systematically lower compared to specimens cast under optimized conditions. The reduced concentration of elements such as Al, Ca, Sr and Ce lead to a decrease of the corrosion resistance of the magnesium alloys in 3.5% NaCI solution.

Jan 1, 2007

By P. C. Garg

"IntroductionThe Central Mine Planning and Design Institute (CMPDI) of India, started planning the extraction of thick seams highly susceptible to heating in 1977by the French method of sub-level caving and/or multi-slicing. Nitrogen flushing was proposed for inhibition of heating by the author in one such project - the Kotadih colliery.Inhibition of heating was unheard of in the Indian coal industry before 1977-78. The usual practice was to seal off a district or a part of the mine or the entire mine when spontaneous heating occurred. With very little equipment in a normal bord and pillar district and a low production rate, the financial loss in capital assets and in production did not warrant any serious thought for inhibition of spontaneous combustion. With the planned advent of longwall mining, particularly sub-level caving, with heavy capital investment as well as high production potential, the sealing of a longwall face due to spontaneous heating could not be considered an appropriate solution.Principle of Inhibition of SpontaneousCombustionFrench engineers have established that a fire will not break out when oxygen is 15% or lower in the general body of the air. However, once a fire starts, the percentage of oxygen has to be reduced to 2% - 4% to extinguish it. It is this principle which has been used at Blanzy Coalfield in France to inhibit heating and it is claimed that this has retrieved the integral sub level method of mining. Nitrogen infusion has been used in Frence since 1978 to keep the oxygen content below 14% in the goaf."

Jan 1, 1987

By Richard W. Herzer

Introduction Thermal methods have been predominant in the metallurgy of the base-metals ever since the foundation of the industry thousands of years ago. Development in hydrometallurgy has been confined largely to the past six or seven decades. It was at first necessarily slow, then for a number of years rapid progress was made. At present, the uncertain state of the metal industry has curtailed research on the subject; however, in the next few years one may assuredly look forward to an ever increasing use of wet processes. Leaching methods have attained the dominant position in the case of certain metals, notably zinc. For others, they have made no headway at all. Copper presents a situation all its own. Due to the varied nature of its ores and to the large number of localities in which it is mined, a great number of processes have been developed, each suitable in its own particular field. In the case of this metal, therefore, it is more difficult to arrive at definite conclusions. It is the purpose of this paper, first, to review the outstanding developments of base-metal hydrometallurgy, and, secondly, to consider possible Canadian applications of some of the processes in use. The discussion will be confined to the three metals, zinc, lead, and copper, with particular reference to the last mentioned. Zinc General Note At present, zinc is produced by two principal processes, the older retort process and the electrolytic process. The latter is a development of the last twenty years and, judging by its present progress, bids fair eventually to supplant older methods in a large proportion of cases. It is certain, at least, that in the erection of a new plant, a hydrometallurgical process would be given the most serious consideration

Jan 1, 1934

By E. G. Joe

"Recent trends in Canadian mineral processing were reported in seven areas of interest covered by seventeen technical papers at the 1976 Annual Meeting of the Canadian Mineral Processors, held at Energy, Mines and Resources' Camsell Hall, Ottawa. New milling equipment included the Enviro-Clear thickener, large-volume Outokumpu flotation machines and abrasion-resistant polyurethane screens. Grinding experiences from a variety of milling operations were reported. Opportunities for increased sizing and grinding efficiency were presented. Flotation control by digital computer and by chemical additions were described in two mill operations. Slurry pumping and sampling techniques were described for various operations. Environmental control in milling was reported concerning dust suppression, arsenic removal and tailings disposal. Several aspects of gold milling were described by the most recently commissioned gold mine and by CANMET. Potash operations were reported showing the similarity of processing and process control to that of metallic minerals."

Jan 1, 1976

By Ian S. Leslie

Seismic monitoring systems for mining operations are being utilized more than ever before in the characterization of rock mass response to underground and open pit mining. This paper provides a review of the use of microseismic monitoring for rock mechanics applications at mines throughout the world. Some practical considerations for the installation of these systems are presented along with techniques for optimizing seismic array coverage. Case studies and installation examples are also provided. Recent applications of advanced seismic analysis techniques are discussed including the determination of event mechanisms, mapping of maximum peak particle velocity (PPV) and seismic hazard fields, and the use of source parameter data for large event re-entry protocol.

Jun 1, 2012

By Theophile Yameogo

Much has been said about the methodology of geomechanical design in underground excavations. However, the geological, hydrogeological and geotechnical complexities encountered at the production horizons in the Athabasca Basin commanded for a novel approach in the geomechanical assessment and design of underground openings. Rock mechanics engineers at Cameco McArthur River have been able to establish a practical methodology that goes beyond known conceptual approaches. In this paper, the author describes the original challenges and unique approach in the geomechanical assessment for drifts and chambers development. The example of the successful development of the 510-8225N Chamber will also be presented.

Aug 1, 2010

By D. Mraz

"In certain instances, rocks around underground excavations behave as a plastic mass. This paper offers several solutions to predicting the mode of plastic flow around cavities and designing mining pillars where plastic conditions exist.IntroductionWhen stresses around underground cavities exceed yield limits of the host rock, the material often behaves as a plastic mass. The best example of this phenomenon is the behaviour of salt rocks in deep salt and potash deposits (more than 500 m deep).However, many other soft rocks exhibit similar properties. For example, Jeremic(1) described certain types of coal yielding plastically under high pressure. Alder suggested that granulated rock behaves plastically.The object of this paper is to propose a de sign procedure for mining pillars exhibiting plastic flow due to the combination of rock properties and in-situ stresses.Prandtl(3) mathematically defined a concept of a generalized, perfectly plastic substance, not possessing the property of strain hardening (Fig. I). He had in mind, a solid with a quasi quasi-isotropic , polycrystalline structure having a well defined yield point, and he postulated that its material elements start and continue to deform plastically when the maximum shearing stress ""'MAX"" reaches a sharp limit, dependent on the mean value of the sum of the major and minor principal stresses:"

Jan 1, 1984

By B. Schulz, T. Leißner, R. G. Merker

"Ores enriched in critical rare earth elements (CREE) keep on being of particular interest. The CREE are Nd, Eu, Tb, Dy, including Y. In conjunction with beneficiation tests on Y-mineral bearing flotation tailings of complicated mineralogy, the Mineral Liberation Analyses (MLA) was used to work out processing characteristics fraction-wise in terms of modal mineralogy, mineral recovery, locking and liberation, and particle size.Size fractions from mechanical sieving (“real fractions”) as well as fractions created virtually by using filters on the MLA-data of the unsieved head material (“virtual fractions”) were investigated comparatively thereby. The ""virtual-sizing-approach"" features a much simpler sample preparation procedure and considerably lower cost if a fraction-wise investigation of a head sample is needed. It can be conveniently applied to intimately locked ores needing a fine grinding to a particle size distribution (PSD) range below 25 microns for instance. However, its practical use is sometimes disputed in terms of the reliability of the results. Results are shown for the main Y-bearing mineral xenotime and selected main gangue minerals of a low grade REE-ore.The influence of sample representativeness, sample preparation and particle counting statistics turned out to be of crucial importance. Given that all preconditions for reliable results are met, locking characteristics, modal mineralogy, and even PSD trends can be read from virtual fractions.The authors encourage processing engineers to use the virtual approach. They propose practical measures to improve the reliability of the MLA results, identify and tackle conflicting results, and mitigate evaluation problems that may arise."

Jan 1, 2016