Search Documents

By E. Herrera, L. Mariscal

"Ilo Copper Smelter operates since 2007 with an ISASMELTTM furnace as a single smelting unit (1,200,000 tpy) associated with two Rotary Holding Furnaces for separation of matte and slag, and which directly produces a discard slag. Southern Peru continually has been improving the slag chemistry of its ISASMELTTM furnace in order to reduce copper losses, given its big economic impact due to large slag mass generation. The present paper describes the influence of the CaO, Al2O3 and magnetite content in the slag of the ISASMELTTM furnace correlated with the SiO2/Fe ratio and its liquidus slag. Also it defines the best slag chemistry and operating practice in order to reduce the copper losses without compromise the bricks life of the furnace.INTRODUCTIONIlo Copper Smelter of Southern Peru (Grupo Mexico) is located on the southern coast of Peru, and treats mainly copper concentrates produced in its own mines (Toquepala and Cuajone).The modernized smelter was commissioned in 2007 and operates with an ISASMELT™ furnace as a single smelting unit (1,200,000 tpy), which is associated with two Rotary Holding Furnaces (RHF) for separation of matte and slag. This slag is directly sent to the dump. Figure 1 shows the smelter flow diagram.The ISASMELT™ process is a bath-smelting process using a single lance. The lance tip is immersed into a molten slag bath contained within the stationary, vertical, refractory-lined ISASMELT™ furnace. The injection of oxygen-enriched air, through the lance into the slag results in a highly turbulent molten bath. Feed material falling into the turbulent bath from above reacts rapidly, resulting in extremely high productivity for a relatively small bath volume."

Jan 1, 2012

By J. L. Wilson

"Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. To assist the new operators, the SAG Mill at B2Gold’s Fekola Mine in Mali needed a robust control that could handle load changes and unmeasured disturbances with minimal operator intervention. With modern Distributed Control Systems (DCS) powerful enough to run advanced control, they often have Model Predictive Control (MPC) blocks built in or available as an “add-on” license, and thus MPC can be readily implemented within the modern concentrator with a relatively low added capital cost. This paper discusses an implementation of two single output MPC controllers to control the SAG Mill at Fekola. This was implemented using the existing signals and advanced control blocks available to the installed DCS.INTRODUCTION Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is that by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. The next step the operator may take may be to cut back the feed rate, or production until the SAG is once again stable. With this sudden reaction comes an abrupt change in SAG rotational speed and power consumption that sends a surge of material down the circuit as the mill suddenly ejects more pulp. Furthermore, choosing a higher rotational speed can lead to higher than normal liner wear as the cataract overshoots the toe of the charge and impacts the liners. After start-up at B2Gold’s Fekola Gold Mine in 2017, the SAG mill was being controlled manually. The SAG rotational speed was adjusted manually by the operator in step changes depending on whether the SAG bearing pressure was increasing, decreasing or stable. During this time of manual control, the SAG fresh feed rate was also adjusted to a tonnage setpoint with a PID controller. Generally, the SAG fresh feed rate setpoint was kept at a target value, but then the feed rate was throttled back if the SAG mill or grinding circuit showed signs of overloading. The extra challenges were that the operators had limited experience and were concurrently learning how the plant operated. Also, they were also occupied with managing situations in the rest of the plant. Often their attention was drawn away from the SAG mill and during that time, the SAG Mill would load up before they could react."

Jan 1, 2019

Iron deposits of every major type except laterite occur in Quebec, and form one of the major iron ore resources of the world. The five principal types of ore described are: (1) hematite-goethite masses derived from iron formation through the oxidation and enrichment of iron by natural processes; (2) taconites consisting of fine-grained iron formation; (3) metataconites composed of coarse-grained iron formation; (4) iron and titanium oxide minerals in massive or disseminateed deposits within gabbro and anorthositic rocks; and (5) replacement or contact? metasomatic magnetite deposits associated with complex silicate and skarn mineral assemblages. Most of the ore, although relatively low grade, is easy to concentrate. The physical properties of the ores that affect the choice and efficiency of beneficiation methods are described. The extent to which iron ore from this area can be utilized in the future will depend on the continued use and improvement of highly efficient methods of beneficiation.

Jan 1, 1964

By J. W. Bingay

The expansion of the mining industry, with other industries, of course, is dependent upon a supply of fresh capital from year to year. Mining is a speculative form of investment, though there is a wide range of risk as between indiudual undertakings. All of the leading financial writers, nowadays, agree that expansion is being seriously interfered with by the unprecedented load of taxation Canadians are carrying. Individuals have less for investment and corporations are obliged to defer necessary expenditures in order that the demands of the taxing authorities may be met. Naturally, speculative investments such as mining exploration suffer first. Undoubtedly, a great deal of cash raised by taxes, if left in the hands of individuals and corporations for investment and expansion, would have been far more beneficially used and would have developed the country more than any use made of it by the government, in the way of bonusing new industries, or the undertaking of large schemes of development. Government undertakings of this nature are often entered into without a proper knowledge of cost and probable return. Expert expenditure of the same sums by business men or corporations undoubtedly would generally produce more prosperity for the country as a whole. The absolute necessity for lower taxation is being increasingly known to the public at large, and eventually it is hoped that our governments will see the economic impossibility of continuing the present rate of expenditure. The successful Finance Minister of the near future will not be the one who can borrow the most money.

Jan 1, 1924

By Marsh A. Cooper

THE THEME of my remarks provides a great deal of latitude. I shall therefore take advantage of the scope it offers to look at our industry across a broad spectrum. My observations reflect a Canadian mining man's varied career as a geologist, mine operator, geological consult ant and company executive in Canada and overseas ... under differing cultures, business environments and political jurisdictions. I was fortunate to come into this industry in the mid-1930's when it was characterized by great enthusiasm, drive and resourcefulness. It was the beginning of a burgeoning era of some 30 years' duration in which the individualist, the entrepreneur and the builder found ample room for expression. As I contemplate the environment in which we now have to operate and try to perceive what lies ahead, I find myself deeply disturbed. Something serious has happened to this industry along the way. It appears that our very success has been the source of our undoing. I believe it is useful to summarize our industry's basic strength at home as a take-off point f or assessing its position in world terms. I hope that I can focus on some of the things that, in my view, must be done for this industry and by this industry to restore Canada's historic role in the world mining community. The Canadian mineral industry provides 140,000 jobs. It pays the second -highest average weekly wages and salaries among the country's major industries. The output per employee in the mining industry is estimated at about three times that for the economy as a whole.

Jan 1, 1977

By T. R. Ellis

The valuation of mineral properties in the U.S. is only partially regulated. The regulations which have jurisdiction or impact appear to have such mainly as a consequence of unintended fallout, since the regulations were designed for other purposes. Court case history can also be important. The combined results are a mixture of bad and good, with important lessons to be learned. Since 1981, the Securities and Exchange Commission has prohibited U.S. listed companies from reporting quantitative estimates of mineralization and the value of mineralization, other than proven and probable reserves. This results in the minerals appraiser (valuator) working with a shortage of data in his everyday work, both on the subject property and in sales analysis. Between 1989 and 1995, all 50 states and essentially all federal agencies adopted the Uniform Standards of Professional Appraisal Practice (USPAP) for real property appraisals (valuations). The major national appraisal societies also require their members to abide by USPAP. A significant portion of minerals appraisals must now follow these standards. This paper will discuss the content of USPAP. It provides a very good framework for the valuation of a minerals property or a mine, both as real property and as a business. However, the credentialing standards for real property appraisers are now prohibitive for minerals appraisers.

Mar 1, 2002

By T. R. Ellis

"The valuation of mineral properties in the U.S. is only partially regulated. The regulations which have jurisdiction or impact appear to have such mainly as a consequence of unintended fallout, since the regulations were designed for other purposes. Court case history can also be important. The combined results are a mixture of bad and good, with important lessons to be learned.Since 1981, the Securities and ExchangeCommission has prohibited U.S. listed companies from reporting quantitative estimates of mineralization and the value of mineralization, other than proven and probable reserves. This results in the minerals appraiser (valuator) working with a shortage of data in his everyday work, both on the subject property and in sales analysis.Between 1989 and 1995, all 50 states and essentially all federal agencies adopted the Uniform Standards of Professional Appraisal Practice (USPAP) for real property appraisals (valuations). The major national appraisal societies also require their members to abide by USPAP. A significant portion of minerals appraisals must now follow these standards. This paper will discuss the content of USPAP. It provides a very good framework for the valuation of a minerals property or a mine, both as real property and as a business. However, the credentialing standards for real property appraisers are now prohibitive for minerals appraisers."

Jan 1, 2002

By N. Tassé

Les substrats organiques sont à la base des biofiltres utilisant la réduction des sulfates pour générer de l&apos;alcalinité et diminuer la concentration des métaux dans des effluents contaminés. Afin de tester l&apos;efficacité de résidus forestiers utilisés dans de tels contextes, cinq types d&apos;écorce de nature et d&apos;âge variables ont été placés dans des contenants hermétiques et mis en présence d&apos;une solution synthétique de drainage minier acide. Le pH, l&apos;alcalinité et les concentrations de Fe2+ et SO4 2- ont été mesurés à intervalles réguliers pendant 70 jours. L&apos;importance d&apos;un éventuel neutralisant minéral et du type de souches de bactéries sulfato-réductrices pour l&apos;initiation et l&apos;évolution des réactions d&apos;oxydo-réduction ont été évalués en utilisant de la dolomite ainsi que des inocula de sédiments portuaires réducteurs et de boues d&apos;usine d&apos;épuration. Une augmentation de pH et des diminutions de Fe2+ et SO4 2- ont été notées dans tous les réacteurs. En l&apos;absence de dolomite, le pH augmentait de 1.6 à 5-6, Fe2+ diminuait de 400 à moins de 5-100 mg/L, et SO4 2- diminuait de 2500 à 750-1250 mg/L. Les échantillons inoculés avec des sédiments s&apos;avéraient légèrement plus performants que ceux avec boues. En présence de dolomite, le pH atteignait 6.5-7.0, et Fe2+ et SO4 2- tombaient à <5 et 20-40 mg/L, respectivement. Le degré de réactivité des résidus forestiers n&apos;était pas une simple fonction inverse de leur âge. Les échantillons ayant le mieux réagi, bien que parmi les plus vieux testés (années 1980), étaient ceux contenant une proportion significative d&apos;écorces de feuillus et peu de bran de scie. Les échantillons avec des proportions élevées d&apos;écorce de conifères ou de bran de scie étaient associés à des taux de réduction moindre. Nonobstant l&apos;amélioration rapide des conditions obtenue avec la dolomite, grâce à une neutralisation initiale plus prompte, il s&apos;avère que le type de résidus forestiers éventuellement utilisé dans une barrière réactive est de première importance pour l&apos;efficacité des mécanismes de réduction. Un système basé sur l&apos;utilisation de résidus forestiers devrait utiliser des écorces (plutôt que du bois) provenant de feuillus (plutôt que de conifères).

Nov 1, 2002

By John A. C. Fortescue

Details of the interactions between the environment and the growth of terrestrial plants may be complex and difficult to study. This paper focusses attention on some of these complexities by means of six examples, each of which provides information on an aspect of the interaction between the growth rate of plants and the chemistry of the environment. The relationships which exist between the information obtained from these examples and the concepts of "holism" and "transfer rate problems" are pointed out and the importance of long-term biog•eochemical studies in Canadian environments is stressed.

Jan 1, 1971

By L. E. Collins

"In western Canada, many new wells contain a significant fraction of H2S. As well, many older wells become increasingly sour over their operating lifetime. For these reasons, there has been increased demand for linepipe and casing for sour service applications in recent years. This paper will review the metallurgical factors which must be considered in designing steels for such applications. IPSCO’s development of linepipe and casing, and experience in fabricating products to meet test standards specified for sour service applications will be summarized. IntroductionWestern Canada produces the majority of Canada’s domestic crude oil and natural gas. A complex system of pipelines has been built to gather the oil and gas from the fields for transport to refining and/or cleaning operations. The gas carried in these pipelines can be either sweet or sour (i.e. containing no H2S or containing H2S) depending on the nature of the field from which it came. Many new fields contain a significant fraction of H2S and many older fields become more sour as their time in production increases. This uncertainty regarding product condition influences the user’s choice of materials for both casing and pipeline applications.It is well known (Merrick, 1989) that hydrogen induced cracking (HIC) will occur in steel when three conditions exist simultaneously: (1) the presence of H2S gas, (2) moisture, and (3) a susceptible material. Steelmakers can only address the latter of these factors. Development of steels to meet test requirements of sour service has been a major focus of IPSCO’s development work for several years."

Jan 1, 1998

By T. Rigg, J. N. Stone

"The process described has been developed to utilize low-grade scrap -turnings, borings, tin cans and other types of ferrons scrap which currently has been of limited or no use in conventional steelmaking processes. If scrap of this type can be converted into high-purity iron by chemical means then there is a potential saving of several million tons of metal annually in North America.The process is chemically quite simple and consists of dissolving ferrons scrap in hydrochloric acid, followed by evaporation and crystallization of the resultant solution to yield ferrons chloride crystal.s. These crystals are dries, briquetted and converted to non sponge by reduction in hot hydrogen. The HCl produced from the reduction step. is absorbed in water and the hydrochloric acid so produced is returned to the dissolver circuit. The hydrogen produced from the initial dissolution of the scrap is used to reduce the ferrons chloride. Purity is maintained by bleeding off impure chloride solutions from the evaporator-crystallizer circuit, and converting these chlorides to oxides and HCI in a high-temperature spray roaster. The HCl produced in the roaster is absorbed in water and the hydrochloric acid returned to the dissolver."

Jan 1, 1970

By J. R. Kish, J. Dabrowski

"The susceptibility to intergranular corrosion modes is a major technical issue preventing widespread utilization of higher strength welded AA7xxx extruded beam profiles, in the peak-aged T6 condition, in automotive bumper assemblies. A study was undertaken to evaluate the relative exfoliation corrosion resistance (ASTM G85-A2) as a function of joint design parameters, namely the base alloy composition, heat-treated condition and beam orientation after exposure to a cyclic acidified salt spray test. This paper documents the major findings extracted from this study.INTRODUCTIONBumper systems play a predominant role in the passive safety of an automobile, since they are one of the main structures for absorbing the collision energy in the event of an automobile crash. Heattreatable AA6xxx-series (Al-Mg-Si) and AA7xxx-series (Al-Zn-Mg) Al alloys, with relatively high strength, toughness, energy absorption, weldability and formability, make it possible to design costcompetitive bumper systems to crush in a controlled fashion. In this context, Cu-lean AA7xxx extrusions, such as AA7003 and AA7108, which exhibit higher strength than AA6xxx extrusion, such as AA6082, represent an attractive light weight material from which to fabricate bumper assemblies (Clausen et al., 2000; Pedersen et al., 2008; Chen et al., 2009).Arc welding is a key joining process for AA7xxx alloys within the transportation industry. A major technological issue preventing widespread utilization of arc-welded AA7xxx joints is the susceptibility to severe localized corrosion (Kent, 1970, Reboul et al., 1985; Holroyd et al., 1987). It generally occurs as exfoliation corrosion within a heat affected zone (HAZ) a few millimeters from the weld bead, or a type of stress corrosion cracking (weld-toe cracking), which initiates at the weld toe and propagates into the interfacial region between the weld bead and the HAZ (so called “white zone”). In addition to the micro-galvanic cell activity induced by the intermetallic compound constituent and strengthening particles present, there is strong evidence that macro-galvanic cell activity between the weld bead and base AA7xxx alloy may be playing a controlling role. Electrochemical profiles taken across fusion welded joints, in cross-section, during exposure to saline solutions suggest that a significant potential difference exists across the AA7xxx arc-welded joint (Shumaker et al., 1967; Grauer and Wiedmer, 1980; Tuck, 1985, Onoro and Ranninger, 1993). These studies consistently show that the HAZ and base alloy are more electronegative with respect to the weld bead (arc-welded with AA5xxx filler wire). Despite this initial important work, the majority of the recent corrosion research effort on welded AA7xxx alloys has focused on the performance of friction stir welds (Lumsden et al., 1999; Wadeson et al., 2006; Hatamleh et al., 2009)."

Jan 1, 2012

By A D. Turnbull

In Canada, although some research on extraction metallurgy is carried out by the universities and by government, the primary responsibility for the research necessary to the mining industry rests on the industry it-self. Automation is coming more slowly to the mining industry than to others, partly because of the problems of instrumentation. Operations research methods are, however, coming into use. Some new developments in the extraction of aluminum, in iron and steel, in pyrometallurgy and in pressure leaching of nickel, copper, zinc and lead are briefly outlined. Mention is made of uranium and the reactive metals. The importance of the by-product metals, notably antimony, bismuth, gallium, germanium, indium and tellurium, in the development of the electronics industry is also mentioned. The trend toward co-operative research by groups of producers, to develop markets for their products, is noted. In conclusion, there are a greater number of trained scientists, as well as larger amounts of scientific knowledge, available to the mineral industry than ever before, and, if properly used, this will result in great benefits to the industry and to Canada.

Jan 1, 1963

By A. E. Lehmberg

"IT IS KNOWN that some ores of sulphide type, such as pyrite, chalcopyrite, and bornite have an electrical conductivity comparable to that of metals, and accordingly much higher than the conductivity of any unmineralized rock. This physical property has long been used for the detection of orebodies of this kind by means of electrical measurements made at the surface of the ground.The present paper will deal with a new electromagnetic instrument for the investigation of subsurface conductors, which has been recently introduced into field practice and has already led to successful results in Canada.The principle of the instrument will be described. How it operates, and how the observations made can be interpreted will be explained. Field examples will •be shown to illustrate its application.Description of Instrument and of Operating TechniqueThe equipment (1) includes a low-frequency alternating current generator. The a.c. is supplied to a transmitter coil and generates a primary field which induces eddy currents in the ground, the intensity of which is proportional to the ground conductivity."

Jan 1, 1952

By O. D. Maurice

"This paper will essentially update the information that is already known and published on the limestones of the Province of Quebec. The excellent report by M. F. Goudge (1935)m is difficult to improve upon and the areas of limestone quarrying are generally the same as they were at the time of Goudge's report. Our knowledge of the limestones of Quebec has been improved considerably in recent years by the publications of T. H. Clark, 2 who, since 1938, has been mapping and reporting on these lime-stones and has discussed their stratigraphy, their structural features, their history and their economic value. One economic aspect is the presence of natural gas in these formations and the possible occurrence of oil. A total of 150 test holes had been drilled to a depth of more than 500 feet by the end of 1967 and, in addition, at least 256 more shallow holes had been put down in the St. Lawrence Lowlands. The information from these test holes has greatly improved our knowledge of the thickness and extent. of the various formations of Paleozoic limestone and shale in Quebec.This paper will then review briefly the limestone occurrences in Quebec, using the old as well as the more recent reports as principal references"

Jan 1, 1970

By K. Duckworth

"AbstractA new electromagnetic depth sounding technique was applied to the measurement of salt thickness above the workings in the Central Canada Potash Mine at Colonsay, Saskatchewan. The initial tests indicate that this new technique can measure salt thickness and that the technique possesses operational feature s which make it possible to monitor trends in salt thickness throughout the mine. The technique can be applied using existing equipment, but the tests do indicate the desirability of developing equipment with features specially suited to the mine environment.IntroductionTESTS were conducted in the Central Canada Potash Mine at Colonsay, Saskatchewan during 1974 and 1975 to determine if a new technique in electromagnetic depth sounding could provide a convenient means of measuring salt thickness above the workings. This new technique, which was described by Duckworth (1975), offers operational features which appear to be advantageous in this particular situation.The problem requires that soundings be made upward from the mine workings to the base of the second red shale. This shale forms an impermeable seal on top of the Prairie Evaporite. A knowledge of this salt thickness is of interest due to the need to avoid any possibility of the workings rising to cut the red shale. Another desirable objective is the detection of any disruptions of the red shale. Ideally, this should be done ahead of the workings in order that such areas of disruption may be avoided."

Jan 1, 1977

By Linlin Zhang

Rare earth elements (REEs) are a group of lanthanides elements which have been widely used in the electronic, petrochemistry, metallurgy, and defense industries. Their demand has increased sharply in the past decade with the boom in electronic device production. Some countries now consider them strategic metals for the future and it has been forecasted that REEs may become a dominant contributor to global economy. In the wake of REE exploration, mining and processing, concern has grown over occupational and community health issues and risks. A portion of available literature on this topic however is written in the Chinese language, and thus research information related to health and REE mining is not readily accessible to mineral development planners in countries such as Canada, where REE mining is now evolving. As REEs also represent an important commodity, primarily stemming from Chinese production, it is important to begin to understand the potential health costs related to this mining sector. There are two main objectives of this paper. The first is to present an overview of REE mining with a focus on geological characteristics, global production and uses with particular attention to the main producer: China. The second is to present the results of a literature review (using both Chinese and English sources) on REE mining and health and identifies key occupational and community health issues that require consideration. This paper concludes by identifying some critical issues this sector needs to address to ensure the sustainable development of this mining activity.

Aug 1, 2013

By J. D. Campbell

"Coal is one of Alberta's major fuel resources, but its distribution, especially in the flat plains region, has been somewhat obscured by surficial deposits. After a period of neglect, easily strippable plains coal is presently approaching a position of dominance in electrical power production, a position it is likely to retain for a number of decades in the face of strong competition from hydro and nuclear power. Accordingly, the Research Council of Alberta has undertaken an inventory survey of the province's supplies of this resource.In the southern part of the province and in the north-central forest-fringe area, some strippable coal is found in the Belly River Formation and its equivalents, but major strippable coal reserves in large areas of central Alberta occur within the Edmonton Formation. The survey is planned on a reconnaissance scale, drilling test holes at 2-mile intervals in selected large areas. It appears to show that, in well-settled regions, large reserves of strippable coal are only to be expected where they have long been known; major presently unknown bodies of coal must be sought in unsettled regions or at depths too great for strip mining. However, such bodies might still be economically competitive with hydro and nuclear power in the production of electric power for some time to come."

Jan 1, 1967

By Wm. T. Bray

SYNOPSIS Canadian Refractories, Limited, produce a wide range of basic refractories. The chief raw material use in their manufacture is the magnesite which is mined, and beneficiated in a heavy media separation plant, at Kilmar, Que. This paper describes the underground operation and the plant and explains how the gravity separation of light, siliceous gangue from the ore has changed the mining practice, increased the ore reserves, and improved the chemical uniformity of the crushed ore. HISTORY REFRACTORIES are essential in the production of steel and base metals and in other high-temperature processes. Basic refractories, chiefly composed of magnesia which is obtained by burning magnesite, are used to line and repair basic furnaces. When World War I cut? off the importation of Austrian magnesite, upon which North American industry had depended, domestic sources bad to be found. In Quebec, work was begun on deposits of magnesite at Kilmar, half way between Ottawa and Montreal and about ten miles north of the Ottawa river. By the end of the war substantial tonnages were being quarried and calcined, but, when Austrian magnesite again became available, the industry declined rapidly. In 1925, the National Research Council, in co-operation with the Federal Department of Mines, began an investigation of the industry&apos;s technical problems. The result of this research work, which was taken over fully by the Company in 1943 and is actively continued, is that the single product of the early 1920&apos;s has been supplemented by more than forty specialized products serving the metallurgical and chemical industries across Canada and in more than thirty other countries.

Jan 1, 1951

By F. K. McKean

THE task of establishing a new corrosion testing laboratory is more difficult than it need be because there is very little information on the subject available in the literature. Many articles describing tests and results may be found, but a wide search will unearth only passing remarks on the different types of equipment that may be selected for accelerated corrosion tests. An article describing some of the apparatus needed in a corrosion laboratory should be of help to those interested in building a new unit or in making additions to an old one. In May of this year, the writer was given the assignment of equipping a laboratory for general corrosion testing, to form a part of the new Physical Metallurgy Research Laboratories of the Department of Mines and Resource~ at Ottawa. With the help of senior members of the staff, along with what could be gathered from other sources, a list of necessary equipment was compiled and a plan for arranging it in the rooms was decided upon. Where possible, the apparatus was constructed in the excellent machine shops at the disposal of this Department, while the rest was placed on order with the manufacturers.

Jan 1, 1945