Search Documents

By J. Don Scott

Analytical predictions of the rate and magnitude of settlement of deposited oil sands tailings slurries generally overestimate how fast pore pressures will dissipate. Field deposits of nonsegregating tailings to mature fine tailings show continued high pore pressures near the surface which impede surface reclamation. In geotechnical analyses which predict the consolidation behavior of soft soils a finite strain theory is used. Effective stress-void ratio and void ratio-hydraulic conductivity relationships determined from laboratory large strain consolidation tests, are used in the finite strain predictions. This theory, however, cannot predict the full range of sedimentation, consolidation and pore pressure dissipation which occurs in large scale deposits of thixotropic tailings slurries. A new large strain consolidation model which assumes that the creep rate of the slurry exceeds the pore pressure dissipation rate is being investigated. This model is relevant for rapidly deposited, low permeability thixotropic slurries where the upwards drainage path increases by several meters a year, such as, in oil sand fine tailings ponds and nonsegregating tailings deposits. The model will be verified by analyzing the 10m high column of fine tailings at the University of Alberta which has been monitored for over 20 years and in which the excess pore pressures are still very high.

May 1, 2004

By P. Quinn

"The Venturi-aerated flotation column (VAC) is based on a reactor and separator design for a new generation of flotation machines. The reactor is a Venturi tube, where the air/slurry contact takes place with intensive aeration for efficient particle collection. The separator is a column of 1-3 m length that provides quiescent hydrodynamic conditions for effective separation of bubble-particle aggregates from the remaining slurry.Aeration in the Venturi tube occurs via two mechanisms: air dispersion and nucleation (cavitation). By forcing air through a restricted passage with a fast flowing slurry stream, air is dispersed into fine bubbles. Bubble formation due to cavitation occurs on the surface of particles in the low-pressure section of the Venturi, from dissolved air contained in the liquid.Size-by-size recovery and flotation rate constants were determined for a small-scale laboratory Venturi-aerated flotation column. The results were compared to those obtained in a laboratory 2.2 L Denver cell. It is shown that the Venturi-aerated flotation column has slightly slower flotation kinetics to the Denver cell, but with much higher flotation selectivity. A portable Venturi-aerated flotation column can effectively be used to investigate process or equipment problems in operating plants.INTRODUCTIONFlotation processes can generally be divided into two sub-processes: 1) selective collection of hydrophobic particles by air bubbles and 2) separation of bubble-particle aggregates from hydrophilic particles that remain in the pulp. The methods of aeration, or bubble generation, control the mechanism of particle collection by either collision with, and subsequent attachment to bubbles, or by in situ bubble formation on the surfaces of hydrophobic particles. A flotation device should provide optimal aeration conditions for efficient particle collection and a suitable hydrodynamic environment for effective removal of bubble-particle aggregates from the remaining pulp."

Jan 1, 2002

By T. Hidayat, D. Shishin, S. Sineva, M. Shevchenko

The effects of the slagging components Al2O3, CaO and MgO on the thermodynamics and phase equilibria of the gas/slag/matte system with major elements “Cu2O”-“FeO”-SiO2-S are characterised using an integrated experimental and thermodynamic modelling approach. The experimental technique included high-temperature equilibration experiments using a spinel substrate in controlled gas atmosphere (CO/CO2/SO2/Ar), quenching of the sample and subsequent measurement of the compositions of equilibrium phases with Electron Probe X-ray Microanalysis (EPMA). Thermodynamic modelling is undertaken using the computer system FactSage. In previous experimental studies on this system, the separate effects of Al2O3, CaO and MgO were determined. In the present investigation, the combined effects of these additional components are investigated at 1200oC and P(SO2) = 0.25 atm and a range of P(O2)’s. Special attention is paid to ensuring chemical equilibrium is achieved in each case, for this reason possible kinetic factors are systematically analysed. The results obtained are presented in the form of graphs showing the compositions of matte and slag phases as functions of copper concentration (matte grade). The new experimental data are used for the improvement of the thermodynamic database for multicomponent copper-containing systems. The effects of the slagging elements on this multicomponent system will be presented in the paper. INTRODUCTION Whilst Fe-O-Si form the principal components of copper smelting and refining slags, additional impurities are present in industrial practice typically at 2–5 wt.% Al2O3, 1–4 wt.% CaO and 1–2 wt.% MgO levels (Davenport, King, Schlesinger, & Biswas, 2002). These elements are introduced into the slag as impurities in concentrates and other feedstocks, in fluxes added to the process and in refractory materials. Understanding, and accurate description, of the changes that take place in the smelting process in the presence of these additional elements is of major importance to the optimization of industrial operations. Although experimental data are available on slag/copper matte equilibria, further work is needed to accurately characterise the influence of Al2O3, CaO and MgO on phase equilibria and elemental distributions of elements in gas/slag/matte systems. The individual effects of the Al2O3, CaO and MgO slagging components on equilibrium phase assemblages under selected conditions have been quantified in a recent series of studies on the Cu–Fe–O–S–Si-(Al, Ca, Mg) gas-slag-matte-metal system (Fallah- Mehrjardi, Hayes, & Jak, 2018; Fallah-Mehrjardi, Hidayat, Hayes, & Jak, 2017a, 2017b; Hidayat, Fallah-Mehrjardi, Hayes, & Jak, 2018a, 2018b; Jak et al., 2016; D. Shishin, Decterov, & Jak, 2018; Denis Shishin, Hayes, & Jak, 2018). Since, thermodynamically, the condensed phases do not behave ideally, it is to be expected that the effects of individual elements may not be additive, and the additional interactions between the Al2O3, CaO and MgO slagging components will also have to be taken into account. These additional effects are expected to be smaller than those of the individual components, so higher accuracy is needed. The present paper describes analysis of the precision and accuracy of the experimental technique on multi-component, multi-phase equilibria in these systems to enable the combined effects of Al2O3 + CaO + MgO on slag/matte/spinel equilibria, i.e. for high Fe/SiO2, to be accurately measured. The effects of Al2O3, CaO and MgO on the gas - slag - matte are analysed using a thermodynamic modelling approach with the computer package FactSage.

Jan 1, 2019

By P. Wells

"In the past decade, there have been many developments in processing of nickel/copper sulfide ores. Improved pentlandite/pyrrhotite flotation selectivity with the use of new reagents, fine regrinding and Redox measurement (control) has led to increased pyrrhotite rejection and thus higher concentrate grades. Flash flotation has increased overall nickel and associated precious group metal recoveries. Recovery of both fine and coarse particles has been improved through an understanding of flotation cell hydrodynamics. The separation of copper from nickel in such ores has seen a similar level of development. From the late 80s to very recently, the use of flotation columns, the use of pyrrhotite depressing reagents and the improved understanding of the complex mineralogy of chalcopyrite, pentlandite and pyrrhotite have considerably increased copper / nickel separation efficiency. Copper concentrate with more than 30% copper and less than 0.5% nickel grade is now obtainable at 80-85% copper recovery from mill feed compared to 70-75% copper recovery with 30% copper and 1% nickel grade only a few years ago. Improved copper / nickel separation in milling operations has the potential to substantially improve the processing of the resulting concentrates and thus the overall return from the extraction of nickel and copper from sulfide ores.INTRODUCTIONNickel metal by itself or in alloys with other metals and materials makes a significant contribution to modern society. The relatively high price that nickel commands compared to other base metals is a reflection of the fact that, although abundant in the universe, nickel is sparingly distributed in the earth’s crust. There are two types of nickel deposits that are currently being exploited: complex sulfide ores and lateritic oxide ores. Lateritic contain no copper but in sulfide deposits, nickel– bearing minerals, principally pentlandite (Pn, [Ni,Fe]8S9), some millerite (NiS) and violarite ([Ni,Fe]S) are often found in association with copper-bearing minerals, mainly chalcopyrite (Cp, CuFeS2) and cubanite (CuFe2S3). The copper content of such ores can vary considerably from as high as 5-8% (in some Sudbury basin ores) to as low as 0.1% (in ores mined by Western Mining at Mount Keith, Western Australia and by Inco in Thompson, Manitoba). The valuable minerals Pn and Cp are almost invariably found associated with pyrrhotite (Po, Fe7S8) which along with nonsulphide rock has to be rejected to tails in the primary milling stage. The bulk concentrate from the primary stage is then treated to depress Pn and float Cp. A complete Cu/Ni separation at the mill would be highly desirable but this is not possible because of locking between a small fraction of the valuable minerals. As a result, Cu/Ni separation has to be carried out both during milling and during refining of the matte following smelting. At Inco, Jinchuan and in Norilsk, a chalcocite / heazlewoodite separation is made by flotation following slow cooling of the matte. In the present Sudbury Inco operations, Cu/Ni separation has not been conducted at the mill since 1991 and all Cu/Ni separation takes place at the matte processing plant. Because of the rising ratio of Cu to Ni in the ore, this strategy is under review and this paper describes some recent studies of circuits in preparation for possible installation of a copper / nickel separation circuit at Inco’s Clarabelle Mill in the Sudbury area."

Jan 1, 2004

By C. V. Umipig, G. G. Hutalle, E. E. Israel

TVI Resource Development (Phils) Inc. Canatuan mine is a polymetallic ore deposit located in the Province of Zamboanga del Norte on the island of Mindanao in the Philippines. The deposit consisted of an oxidized capping of gossan overlying a Besshi type volcanogenic massive sulphide lens which is near surface and flat lying. Construction and development of a sulphide processing plant began in early 2007 and commissioned in November 2008. During the initial stages of sulphide operation, high copper (Cu)-low zinc (Zn) ore was fed to the plant. Marketable copper concentrate at 91-95% recovery was produced utilizing a high-pH bulk sulphide rougher flotation and 2 cleaning stages. Because of increased levels of Zn of the ore body, a Cu/Zn separation circuit was initiated in early 2010 following an intensive laboratory test work program. This Cu/Zn separation circuit was necessitated because of the copper ion pre-activation of the sphalerite that lead to the zinc being readily recovered to the copper rougher concentrate. In-situ activation of zinc (in the pit and stockpiles) was caused by the leaching of secondary copper minerals in the ore (particularly from the dominant copper species, chalcocite and covellite). This problem required the development of metallurgically complex and intensive reagent regime to effectively depress the activated sphalerite. As well, the immediate reactivation of zinc after it has been depressed, at the onset of Cu/Zn separation flotation, added additional metallurgical complexity to the process. Subsequent to the Cu/Zn separation circuit, an unconventional, yet proven effective, simultaneous cyanide detoxification-zinc flotation circuit was set-up to recover the zinc. Laboratory test work results realized Cu-Zn recovery differential from a Cu/Zn separation circuit of over 40-45%. This performance has been achieved in the plant, at 72% Cu overall recovery. With the gradual improvements on-going with zinc circuit capacity and effective zinc separation being achieved, zinc recovery has currently reached 40%.

Jan 1, 2012

By J. Andrew Cornier, Mike Cooper

"Upon successful completion of the AG/SAG Mill project (Cooper et al., 2001) the Brunswick Mine concentrator was configured with single line processing through the AG/SAG mill, followed by two parallel ball mill and flotation circuits. The Stage Grinding project was undertaken to utilize a pre-flotation stage on the AG/SAG mill primary cyclone overflow and simplify the flowsheet by consolidating the two ball mill and flotation circuits, resulting in single line processing fi-om AG/SAG mill to final concentrate. Concurrently, the reclaim water supply capacity was increased to enable flotation cleaning at lower percent solids.Benefits from the Stage Grinding project include revenue enhancement from increased zinc grade and recovery combined with additional lead recovery. Further benefits included a reduction in the number of process pumps, reduction in loss associated with spillage to sumps and process simplification through efficient use of equipment layout.The Stage Grinding project was implemented in six phases over a period of seven months in 2000. Each phase was commissioned during scheduled concentrator shopdays with minimal additional downtime required. One year after project approval the Stage Grinding project was completed at a total cost of $1 1.8 million.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is one of the world’s largest leadzinc mines. Milling of ore began in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore fkom the No. 6 open pit located several kilometers away. In 1980 the pit was exhausted and the concentrator rationalized to accept a design feed rate of 10,500 tomes per day from the No. 12 mine. In excess of 100 million tomes have been milled to date, representing over three-quarters of the known reserve. The concentrator employs differential froth flotation to produce lead, zinc, copper and leauzinc bulk concentrates. The ore is massive sulphide, with approximately 20% valuable minerals, 60% pyrite and 20% silicates."

Jan 1, 2002

By L. A. Melis, J. W. Rowson

"Cluff Mining operates the Phase II uranium mine and mill at Cluff Lake, northern Saskatchewan. During the Phase I operation, uranium tailings were generated by acid leaching of a gravity concentrate and high-grade ore for uranium recovery. The pre-treatment gravity process, as well as the high-grade nature of the ore, led to a concentration of gold in the tailings which justified the installation of a small circuit to recover the contained gold. The operating circuit consists of tailings repulping, grinding, cyanidation, carbon-in-pulp, gold recovery, and cyanide destruction by acidification, volatilization and re-neutralization. The process is described and typical operating parameters are provided. 1.0 INTRODUCTIONCluff Mining, a Saskatchewan partnership, is owned 20 percent by Saskatchewan Mining Development Corporation (SMDC) and 80 percent by Amok Ltd./Ltee. (Amok), manager and operator of the partnership.The current operation includes the Phase II uranium mining and milling facilities, located at Cluff Lake 700 km north of Saskatoon, capable of processing 300,000 tonnes of ore to produce about 4,000,000 lbs. U308 (1500 tonnes of uranium) per year.The Phase I operation was initially established to process the very high grade ""D"" uranium orebody from 1980 to 1983. The leach tailings from the operation Phase I mill operation were found to contain elevated levels of gold. These high gold values were partially due to the gravity pre-concentration step included in the uranium recovery circuit, and to the naturally high levels of gold associated with the uranium mineralization in the ""D"" orebody."

Jan 1, 1988

By John Kazakoff, Andrew Mortimore

"Production at the remote Kumtor Gold Mine in Kyrgyzstan commenced on schedule in December 1996.The ore mined during the first few months of 1997 from the upper benches of the pit did not produce the results predicted by the feasibility study. Low metallurgical recoveries experienced at the time were cause for great concern.It soon became clear the recovery difficulties centred around the preg robbing nature of the ore.Procedures were developed to selectively stockpile highly carbonaceous low recovery ore types. Testing methods were developed in the mill to quante the preg robbing activity of the ore. Preg robbing masking agents were added to the process to reduce the preg robbing activity of the ore.The importance of coconut carbon activity relative to the preg robbing activity of the ore was realized. Every aspect of the performance of coconut carbon in circuit was evaluated and optimized to improve carbon activity.Mineralogical analyses were completed defining the deportment of gold in ore and process tailingsBy year end the recovery difficulties had been overcome and plant design production had been achieved. Process improvements continue through 1998."

Jan 1, 1999

By Jason Rrno

The emergence of Impact and Benefit Agreements (IBAs) in the Canadian mining sector has been read by many as a positive governance innovation. Negotiated directly between mineral resource developers and Aboriginal communities with limited government interference, IBAs serve to manage impacts associated with a mining project and deliver tangible benefits to local communities. Notwithstanding their increasing use and significance, limited systematic analysis has been undertaken to determine whether they are, in fact, working. This paper reports on the effectiveness of a number of IBAs negotiated in support of three northern Canadian diamond mines, drawing on evidence from time-series data, key informant interviews, and focus group meetings in Yellowknife and Dettah, NWT, and Kugluktuk, NU. While some deficiencies were apparent and perceptions of effectiveness varied somewhat by Aboriginal community, the IBAs were generally found to be meeting their objectives, especially with respect to the delivery of benefits. For Aboriginal communities affected by mineral development in the Canadian North, this represents a significant change to typical outcomes of the past. Moving forward, research on IBA effectiveness needs to adopt a longer timeframe and begin to gauge the degree to which IBAs are able to address long-standing concerns associated with hinterland resource extraction beyond their agreement-specific objectives.

May 1, 2010

By Rocky (Yaokun) Wu

This paper introduces the development and application of a new cable anchor - Cable-Lok for pre-stressed cable bolting in mines. Cable-Lok is a spring-loaded cable anchor suitable for the drill hole diameter of 50 and 65 mm (2" and 2.5") in medium soft rock to hard rocks. The cable anchor is automatically set on installation and the cable can be tensioned immediately to provide active and primary support throughout its length. Post-grouting can be conducted independently. In comparison with the conventional cable bolting, Cable-Lok anchor will greatly speed-up the cable bolting circle and decreases the cost of cable bolting. Cable bolting anchored with Cable-Lok anchor has wide application in mines, e.g. pre-stressed cable bolting in large span drifts and intersections for permanent rock support, or in hanging walls or stopes for temporary support, or cable lace anchoring etc. This paper introduces the principle of pre-stressed cable bolting and the specifications of the Cable-Lok anchor, presented the testing results in laboratory and the application cases in mines.

Oct 1, 2010

By Sunil Koppalkar, Guillaume Noel, Ahmed Bouajila, Makni Sami, Claude Gagnon

"Gold gravity recovery circuits utilizing enhanced gravity separators have become an integral part of many of the modern gold processing plants. Thus, efforts to improve the operating efficiency have been a topic of interest for metallurgists for many years. As part of this endeavour, a methodology to estimate the portion of gold in the ore that could be recovered by gravity separation (gravity recoverable gold or GRG) was developed at McGill University. It has been reported in the literature that the gold content estimated with this methodology is the theoretical maximum that is available for gravity recovery that could only be approached but never achieved. A comparison of GRG recovery obtained in the laboratory with the actual recovery in the plant shows that plants recover between one-third to two-thirds of the value predicted by the laboratory test.Research conducted at COREM shows that particle shape transformation during grinding is a major cause of the discrepancy (even though the bleed percent processed, the quality of cyclone classification and the operating conditions of the gravity separator also contribute to the difference). To analyze the gold particle shapes and their deportment, samples were collected from different streams of a grinding-gravity circuit in a gold plant and compared to a concentrate sample from the standard GRG test. A particle characterization methodology based on gold morphology was developed. GRG mapping in a conventional grinding-gravity circuit and the transformation of GRG into non-GRG, as mainly explained by gold particle reshaping, will be discussed. The knowledge gained from the shape analysis will be used to develop shape distributions and partition curves for the classification of shapes.INTRODUCTIONGravity concentration using centrifugal concentrators has gained increasing popularity since the invention of the enhanced gravity concentrators in the nineteen eighties. Among these, the semicontinuous centrifugal gravity concentrators are most commonly used for recovering gold and platinum group minerals (PGM) from grinding circuit streams. The benefits of gold gravity recovery are now well understood and the acceptance by the mining industry is overwhelming. The occurrence of reasonable amounts of gravity recoverable gold (GRG) in an ore prompts gold mills to install gravity circuits. Thus, the increased use of gravity concentration has necessitated a better understanding of the behavior of gold in grinding circuits and of the factors affecting the performance of the gravity concentrator (Laplante et al., 1995). Due to its high density (19.3 g/cm3 when pure) and malleability properties, gold tends to accumulate in circulating streams making it attractive for gravity recovery. The gravity recovery units are typically installed on a bleed stream of the cyclone underflow, mill discharge or cyclone feed."

Jan 1, 2011

By B. M. Coombes

The McCracken and Stacey (1989) method of assessing geotechnical risk for largediameter raisebored shafts has been the basis for most Australian pre-construction raisebore investigations for the past 20 years. At the time of its publication, the McCracken and Stacey (M&S) Method did not include a database of raisebore diameter and rock mass conditions versus actual performance. It did, however, provide a chart that quantified geotechnical risk in terms of proposed shaft diameter and the raisebore rock quality index, QR. Two parameters, RQD/Jn and Jr/Ja were identified as being critical to raisebore stability, but the contribution of these to overall raisebore stability was not quantified. Peck and Lee (2008) published a database of raisebore performance from Australian case histories. Raisebore diameter and ground conditions, in terms of a Lower Bound QR value, were presented for 50 cases versus raisebore performance. This paper updates the database with further case histories and corrected SRF values. This paper further evaluates the reasons for the variable raisebore performance for similar RSR values. For all case histories, three parameters, RQD/Jn, Jr/Ja and Jw/SRF are investigated to assess their influence on raisebore performance.

May 1, 2011

By P. Botane, A. Cailleau

"Compagnie Miniere Esperance operates a gold primary ore body. The ore is processed through crushing, grinding and gravity concentration generating tailings with remaining fine gold. Analyses of the tailings proved a residual gold grade sufficient for a chemical treatment.As lab tests proved the technical feasibility of a pre-concentration using flotation, an on-site pilot operation has been carried out to assess the continuous circuit performances, define the best configuration and obtain enough data for the industrial circuit sizing.Data collected during the pilot campaign have been used for calibrating a process simulator built with the USIM™ PAC software. The simulator validated the feasibility of upgrading the existing plant, including the reprocessing of tailings to obtain a good fine gold recovery in a small amount of concentrate. A preliminary capital cost has been achieved to assess the flotation workshop profitability.INTRODUCTIONCompagnie Miniere Esperance (CME), a mining company based in French Guyana, operates a gold primary ore body in open pit. The ore is processed through crushing, grinding and gravity separation in two stages: a top plant and a bottom plant. A “coarse” pond contains tailings of the top plant; this product feeds the bottom plant. Tailings of the bottom plant are stored in the “fine” pond.Analyses of the fine ponds proved a residual gold grade sufficient for a chemical treatment. However, direct cyanidation would require a too large installation, regarding the local conditions (accessibility, supplying and meteorological conditions).It has been then decided to test the feasibility of a pre-concentration using flotation. Lab tests have been carried out by SGS Lakefield (Canada) in March 2007, which proves the technical feasibility."

Jan 1, 2009

By S. Dessureault, J. Porter, M. Woodhall

Information and communication technology (ICT) is seen as a key source of future productivity improvements in mines. The information technology infrastructure (ITI) necessary to achieve these productivity improvements will come in the form of data integrated from multiple source systems throughout the mining value chain. Two pure approaches are available: supplier-controlled or operations controlled data structures; each strategy has its own advantages and disadvantages. Case studies involving the South African mining industry are used to demonstrate the advantages of using hybrid-controlled data structures. Depending on the level of operational control, new skills are also necessary to be learnt by mining professionals including: information engineering; creating consistent and quality data; and process improvement techniques that use the integrated data for improving the operation.

Jan 1, 2004

By Brian Hart, Hong Zhong, Liuyin Xia, Kyle Douglas

"The application of hydroxamic acid as flotation collectors is fast becoming of significant interest for the selective flotation of oxide minerals along with upgrading oxidised based metal ores and minerals. In the hydroxamate molecule, both O and N atoms in the -CONHOH group are identified as coordination atoms in many complexes and their characteristic structure determines the strength of the chelation complex between the hydroxamate and metal ion. The chelating performance of hydroxamates with transition metals including Cu, Ni, Zn, Fe, Cr, Mn and Co, the alkaline-earth metals (Be, Ca) and heavy metal (Pb) has been studied. Cytec has developed and patented a range of alkyl hydroxamates as flotation collectors for oxidised base metal sulphides, metal oxide minerals and precious metals. This paper introduces two new structures of hydroxamate collectors (Cyclohexyl and 4-tert-butylbenzoyl hydroxamates) and evaluates their characteristics relative to alkyl and benzoyl hydroxamates. Laboratory small-scale flotation tests were conducted with ilmenite and wolframite. The use of 4-tert-butyl benzoyl hydroxamate resulted in a best flotation performance for ilmenite. A relatively low cyclohexyl hydroxamate dosage was required in the flotation of wolframite to obtain comparable results to the alkyl and benzoyl hydroxamates. It is also shown a significantly improved flotation performance with 4-tertbutyl benzoyl hydroxamate in the flotation of ilmenite plant ore in comparison to the oleic acid or fatty acid collectors typically used for ilmenite flotation.INTRODUCTIONHydroxamic acid has been reported as an effective collector in small-scale flotation tests for a wide variety of oxide minerals and ores including copper (Lee et al., 1998, Lee et al., 2009), iron (Quast, 2000), tin (Sreenivas and Padmanabhan, 2002; Wu and Zhu, 2006), tungsten (Marinakis and Kelsall, 1987; Xia et al.,2004), and rare earth metal minerals (Ren et al., 1997; Pradip and Fuerstenau, 1991; Assis et al., 1996; Pavez et al., 1996; Zheng et al., 1996; Chen et al.,2005).As part of our previous research project, a selected suite of hydroxamic acid collectors including fatty, aromatic and modified hydroxamates (naphthoyl, cyclohexyl, benzoyl, octyl, 4-tert-butyl benzoyl, salicylic hydroxamates) were tested in order to examine their potential for recovery and selectivity of rare earth minerals. In these tests it was shown that the flotation performance with the hydroxamate collectors was significantly better than the phosphoric acid collectors on no slimes removed samples (Brian, et al., 2014; Liuyin, et al., 2014 and unpublished internal technical reports). Furthermore the tests revealed that for most of the hydroxamate reagents tested, their dosage requirements to achieve recoveries at the same levels was less than that for the phosphoric acid collectors. Recovery of both La and Ce was significantly better for the salicylic hydroxamate and that Nb, Y and Zr recovery were favoured by the octyl and benzoyl hydroxamates (Brian, et al., 2014; Liuyin, et al., 2014). Comparison among the hydroxamate collectors showed that the flotation and recovery performance of cyclohexyl (CHH) and 4-tert-butyl benzoyl (TBH) was not as good as the other hydroxamates for rare earth recovery."

Jan 1, 2015

By Ben Murphy, Tomi Maksimainen, Antti Rinne, Ishmael Muzinda, Toni Mattsson

"A 500m3 flotation cell was commissioned during 2014 at the Kevitsa Mine in northern Finland working as the first rougher in the copper flotation circuit. Treating around 850tph with an average grade of 0.3% Cu, the TankCell® e500 has run with an average copper recovery of 71% and an average enrichment ratio of 50 during early optimization test work. In addition the cell has proved to be very energy efficient, being operating with a specific energy of around 0.4kW/m3 under production conditions.A review of the installation and operation of the TankCell® e500 at Kevitsa will be presented. Metallurgical performance of the cell during the operating period will be discussed on the basis of on-line analysis and the metallurgical samples collected during early optimization campaigns.IntroductionThe past three decades have seen a rapid increase in the size of mechanical flotation cells. This has been largely driven by demand from the copper industry to process larger volumes of material due to combination of declining head grades and the desire to benefit from the economies of scale (Lynch, Harbort and Nelson 2010). During this period Outotec has been at the forefront of development of large flotation technology with an enviable scale-up track record; 100m3 (1995), 160m3 (1997), 200m3 (2002), 300m3 (2007), 500m3 (2012) to the largest commercially available cell at 630m3 in 2013. This scale-up methodology has been developed, tested and validated (Elgueta et al., 2009; Coleman & Dixon, 2010) by the large installation base of cells in the 300m3 size class operating (over 400). The learning from large cell operation are then reviewed and incorporated back into new designs and scale-up practices (Murphy, Miettinen, and Yanez, 2014)."

Jan 1, 2016

By Turgut Yalcin

"Recent years have seen a resurgence of interest in flotation cell design, and one of the areas where attention is being focused is flotation in centrifugal fields which aims at increasing the flotation rates by forced bubble-particle contact.A new cycloflotation device was developed at Laurentian University and tested on the nickel ore of Falconbridge Limited in Sudbury. In comparison with conventional flotation, cycloflotation yielded at least seven times faster flotation rates in terms of the mass of solids floated per unit time per unit flotation volume, while producing concentrate grades similar to those of conventional flotation. These results, which were obtained with a bench-scale ""cyclofloat cell,"" suggest that cycloflotation has the potential of setting a new direction in flotation technology.IntroductionFroth flotation is no doubt the dominant separation technique in the mineral processing industry. Since its inception early in this century, much research effort has been and is still being expended on this process. Until recent years, emphasis seems to have been placed on the chemical aspects of flotation, but there is now an increased awareness for the need to improve flotation machine performance and more and more attention is being directed towards this area. In a 1982 article on ""Flotation Machines"" (Young 1982) it is stated that "" ... by now the design of the machines used would have reached a high level of perfection, ... In fact, this is not the case ... "".The process of flotation in a flotation device may be considered to take place in several distinct stages as follows:"

Jan 1, 1994

Cobalt mostly occurs as a minor, but valuable, constituent in most nickel and a few copper ores, however it is not generally found alone in commercially viable deposits. Its concentration and extraction are therefore intimately linked to the recovery of the primary metals and the major task for the metallurgist is to extract cobalt of commercial grade from a much larger mass of either nickel or copper and sometimes both. With a particular focus on Vale Inco?s operations, this paper provides a brief overview of the mineralogy of the main deposits being currently exploited that contain cobalt as a co or by-product. The concentration and then extraction to metal are reviewed and some advances released into the public domain are discussed.

May 1, 2009

By K. Leung, J. E. Udd, L. B. Geller, F. Kitzinger

"Sixteen miners died tragically at the Paymaster gold mine in Timmins, Ontario, in February 1945 when a badly corroded hoist rope broke. The investigation of the Royal Commission that followed arrived at a number of recommendations (The Legislative Assembly of Ontario, 1947) aimed at avoiding future disasters of this kind. One consequence was the development and legislated use in Canada, several decades ago, of powerful electromagnetic (EM) instruments for the non-destructive testing of mine shaft wire ropes. The authors have been involved for many years in the design, production, and testing of EM instruments (Geller and Udd, 1990, 1992; Geller and Kitzinger, 1991; Geller et al., 1992). Since the mid-1990s, particular attention was paid to the design and operational results obtained from the computer controlled portable MagnographTM II wire rope tester (Geller et al., 1995, 1998).In the present paper, the authors summarize further hardware- and software-related developments of this instrument. Further, an account is given of the results obtained from the most recent design known as the Perma- ScanTM testing system. This is also a computerized dual-function system. In it, however, the sensor head is designed primarily, if not solely, for permanent installation and for remotely controlled operation. This represents a basic departure from traditional designs, which were intended for ad hoc temporary installations. The remote-controlled instrument described in this paper has now been in operational use for more than four years."

Jan 1, 2003

By G. K. Mann

Fragmentation analysis of blast or crushed rock material is a time-consuming and costly process. During the last two decades, the mining industry has been investigating image-based analysis systems as an alternative to generate fragmentation results. Many image-based techniques and commercial products have emerged during the last few years, and the mining industry has recently begun using these tools for real-time estimation of size distributions. Some existing systems require manual image editing to add or delete edges (or net) before executing the fragmentation analysis routine. This manual procedure may take hours of time for each image analyzed. Reliable and robust image segmentation should be able to handle a wide range of rock textures and sizes under a variety of lighting conditions. This paper describes a novel software application, which has the capability to autonomously capture images and analyze them to generate the particle size distribution. The system can also process a batch of images captured during a fixed duration of time and produce the overall particle size distribution. The new method has different layers of segmentation modules, which allows the system to operate under a wide range of rock textures and lighting conditions. A new grey-level slicing technique is developed which can perform under a range of illuminating conditions. The Canny-based edge detection technique is used to segment rocks appearing in dark regions.

Jan 1, 2006