Search Documents

By J. H. Archibald

"In mines employing cut-and-fill stoping (sand fill), ore passes are built as mining progresses upward. These ore pass raises are generally made from timber and form a vertical ""chimney"", like a very tall log cabin. Traditionally the chimney, or raise, is square in shape and is constructed from square timbers with stepped ends as shown in Figure I. The timbered raise is thus surrounded by sandfill on its outside, leaving the centre open for passing ore down through it. Each layer consists of four timbers and rests flush on the layer below. The corners are frequently pinned or spiked.Under certain conditions in sandfilled stopes large horizontal loads may be transmined to the raise cribbing timbers, or the ""chimney's"" walls. In deep mines, where rock bursts are a problem, it can be shown that one of the conditions for rockbursts to occur is that the burst zone be stiffer and weaker than the surrounding rock(l). This allows a strain energy build-Up in the rock surrounding the burst zone, and the rate of release of this strain energy is known to be related directly to the over-all strength and stiffness of the rock in the burst zone. In stopes that are sandfilled, attempts are, therefore, usually made to increase the strength of the sandfill by the addition of large-sized waste rock and Portland cement. These measures usually achieve the desired strength of the sandfill and, consequently, the severity and frequency of rockbursts can be reduced.Problems may arise when the now chunky sandfill transmits high loads to the raise cribbing along with relatively large move- merits. This leads to heavily stressed and strained cribbing timbers the Coeur d'Alene district in Idaho, raise cribbing failures are common. A typical mode of cribbing failure is shown in Figure 2. One learns in statics that a structure shaped like the crib in Figure I is inherently unstable , at least from a structural standpoint. The crib has pivoted, in Figure 2, into a rhombi c shape and supports very little load. Soon the four-foot square raise cribbing made from 5 in. by 5 in. timbers will no longer pass ore."

Jan 1, 1991

By F. C. Robles Hernandez

This paper presents the results of the electromagnetic semi-solid treatment of the 319 aluminum foundry alloy, Various levels of structure modification were achieved controlling the AC current used to create the Electromagnetic Field, thus manipulating the intensity of the field, The level of grain refinement, partial modification of the Al-Si eutectic, as well as cellular dendrites were observed, A quantitative analysis of the structure was performed using Image Analysis (IA) techniques. In addition a novel Thermal Analysis methodology was developed for the on-line determination of the microstructure modification level.

Jan 1, 2004

By Q. Li, X. -L. Lei

Accompanying global energy shortage and high energy prices, shale gas has been the focus of exploration and it has attracted great attention from both academia and industry. The combination of horizontal drilling and hydraulic fracturing enables the extraction of huge quantities of shale gas from impermeable shale formations. During the process of hydraulic fracturing, great amounts of water, sand and chemicals must be injected into the shale formation at a high pressure, which may trigger seismicity. Such events could occur due to the presence of faults or the reactivation of these potential faults. Shale is the main component of source rock in the Sichuan Basin, China, and has the greatest contribution to the natural gas of the basin. In order to investigate the fracturing mechanism of shale in the Sichuan Basin, China, a series of rock fracture tests under triaxial compression were carried out in the laboratory in order to investigate the hydraulic fracturing behavior in relation to the seismicity. Based on the high multichannel waveform recording system, the detailed spatio-temporal distribution of acoustic emission due to micro-cracking was used to examine the deformation and fracture behavior of shale. In addition, the effects of confining pressure on the deformation and fracture in shale under triaxial compression by acoustic emission monitoring and X-ray computed tomography were discussed in the paper. The experimental results indicate that the shale samples demonstrate brittle fracture behavior. The confining pressure has a great effect on the complexity of the fracture planes and the spatial distribution of acoustic emissions, but few contributions to the location of the major hydraulic fracturing plane. The foliation of shale plays a dominant role in the rupture process and the geometry of the major hydraulic fracturing plane. The high confining pressure increases the strength and restrains the deformation of shale during compression process. These results shed some light on the understanding of onset of hydraulic fracture initiation not only for shale gas exploration and production, but also for CO2 geological storage and underground energy storage.

Jan 1, 2015

By E. You

The concentrator at Kennecott Utah Copper currently has 4 lines with a configuration of one SAG mill feeding two ball mills. The slurry that reports to each ball mill will vary resulting in an unequal load of material. This configuration contains two separate sumps that receive material from a distribution box relying solely on natural slurry flow to feed each sump. The unequal split to each mill results in one mill receiving a greater amount of material. This will result in the equipment on one mill reaching limitations that may affect product quality and the operation of the equipment near maximum. The parallel mill in this condition will often have additional capacity that can be used but cannot be utilized due to the unequal split. The major consequences of this issue result in reduced throughputs and metal recovery. To resolve this condition an advanced control strategy was implemented to control the split in April of 2002 using equipment that was in place.

Jan 1, 2007

By Champoux. G., E. Ghali, W. Zhang, G. Monteith, A. -M. Lafront, G. Houlachi

The efficiency of the electrowinning process of zinc depends on the performance of oxygen evolution reaction, anode quality and corrosion resistance of lead anodes. Original surfaces of rolled commercial lead-silver anodes were examined using conventional polarisation methods in acid zinc sulfate electrolyte with manganese sulphate at 38 °C. The self-discharge method (potential decay) following 5 h polarisation at 50 mA cm-2 was considered to evaluate electrochemical activity, oxygen overpotential and anode stability. The influence of silver content is compared to that of the microstructure, the fabrication process and the composition of the corrosion products. Polished anode samples have also been examined for microstructural and corrosion performance studies. The experiments show that the duration of the plateau at 1600 mV versus SHE, the potential level (active corrosion state/stationary state) and the rate AEco/At during the decay could be a good indicator to compare the corrosion rates of the anodes in industrial zinc electrolytes.

Jan 1, 2008

By C. Stapel, I. C. Tânczos, R. J. De Meijer

"Abstract -In recent years the Environmental Research Group of the KVI has been developing a number of radiometric techniques that may be employed in mineral sand exploration. These techniques involve: radiometric fingerprinting for assessing sand provenances and mineralogical composition; thermoluminescence for dating and provenance determination of sediments; a towed seabed detector to map seafloors for radiogenic heavy minerals and assessing heavy mineral volumes; and simplified transport mechanism models to explain and predict heavy mineral concentrations.All techniques exploit the property that heavy minerals as a group contain concentrations of naturally occurring uranium and thorium that are a hundred to a thousand times higher than in light minerals. In this paper the physics of a number of methods will be described together with a number of results. Based on these results potential applications to mineral exploration and mining are discussed."

Jan 1, 1994

By John Clancy, Andrew J. Freyman

"Trends in world coal markets indicate that the next twenty years could be a period of intensive development for British Columbia's coal resource. This paper examines demand projections for metallurgical, thermal and chemical feedstock coals, with particular reference to domestic and Pacific Rim markets. Supply possibilities, from the point of view of British Columbia's competitive position, are explored, with emphasis on the interaction of such factors as capital, labour, port and transportation requirements.The paper concludes with an examination of British Columbia's strategies in light of the foregoing, and comments on the government's role in ensuring that development of the coal resource be attained in a manner consistent with over-all provincial goals and objectives.IntroductionFor the purposes of this paper the Pacific Rim is defined as including, in addition to Canada, the following: Japan, Korea, the People 's Republic of China, Hong Kong, Taiwan, the countries of the Indonesian Archipelago, Australia, New Zealand and the Pacific-bordering countries of South America and Mexico. The United States has been excluded in this definition in order to better illustrate the economic growth potential for British Columbia coal in the Pacific Rim economies.In the past decade, the Pacific Rim economies have grown faster than most other economies in the rest of the world; economic growth rates of 10 per cent were common in the region prior to the 1974 slowdown and the average rate of economic expansion in the mid-1970s has exceeded 6 per cent. Rapid expansion of international trade in the region has been a major stimulus in this process. By 1979, Pacific Rim two-way trade has reached an estimated $550 billion-about 20 per cent of world trade."

Jan 1, 1982

By William Hawker, James Vaughan, Jeff Chen, Antony van der Ent

"Nickel agromining utilizes hyperaccumulator plants (“metal crops”) to extract nickel from low-grade soils, a process that yields high-grade nickel bio-ore. This feedstock is further processed into a range of nickel products. The bio-ore is relatively free of impurities that complicate the traditional processing of laterite nickel ores. In this paper, current primary nickel processing routes and proposed nickel bio-ore processing options are summarised. A novel pyro-hydrometallurgical route demonstrated at the laboratory scale is described. This process produces a precipitated nickel hydroxide product and takes advantage of the water-soluble basic compounds in the ash to minimise reagent requirements, thereby making it suitable for small-scale implementation in close proximity to the nickel farm. In this process, nickel is precipitated from the leach solution using the basic ash wash liquor. Leaching nickel from ash generated from open air burning requires strong acid and long residence times to obtain high recoveries due to its complex nature and distribution of nickel in multiple phases. This process can be improved by optimising the ashing process with respect to nickel leachability.INTRODUCTIONHyperaccumulator plants have the unique capacity to ‘biopurify’ and concentrate certain trace elements (e.g. nickel) from the soil into their biomass (Reeves 2003; van der Ent et al., 2015). Cultivating these plants as ‘metal crops’ by periodically harvesting and incinerating their biomass generates a high-grade bio-ore (Chaney et al. 1998; Li et al. 2003). This process is called phytomining or ‘agromining’ which is an emerging technology for extracting nickel from sub-economic resources (van der Ent et al., 2015). Potential near-term applications of the technology include implementation on land ahead of processing of the underlying ore-body (Willis 2015), as a mine-site rehabilitation strategy or as an alternative crop for farmers on land that is not suitable for normal food crops. In the longer term, nickel agromining could provide a significant supplement to the nickel supply chain. Critical to the success of agromining is effective bio-ore processing. Due to the unique chemical composition of this feedstock material, existing processes are not very efficient. Our current research efforts aim to develop new process options that overcome limitations of previously trialled routes. In this paper we summarise conventional nickel process routes and proposed new options for producing agromined nickel."

Jan 1, 2016

By Scott Hean

"Environment and the economy are interwoven irrevocably. They need to be publicly discussed, and discussed often so that new approaches can be understood and developed - approaches which are complimentary, not confrontational.Discussion on the environment is timely, from the perspective of mining engineers and developers, from that of bankers and from their shared perspective as people concerned with enhancing the quality of life, the environment and the economy.This paper will touch on how what is called the ""environmental economy "" that has evolved has become entangled with regulatory and financial issues in a way that is dangerous for all of us. It will also look at some of the promising possibilities that a world-wide and continuing concern for the environment holds out for us.For many decades, British Columbia has provided some of the key examples of the intertwining of environmental and economic issues, and, very importantly, providing the people prepared to do something about them.Canada's first environment minister, the late Jack Davis, came from British Columbia. He led this country's delegation to the Stockholm Environment Conference in 1972, a conference that laid the groundwork of principles necessary to establish some international certainty as to the legal liability for causing trans-national environmental damage.Another British Columbian who was also a national environment minister, John Fraser - now the Speaker of the House of Commons - was one of the first to dramatize the importance of acid rain and force it into the international public arena.Some 20 years ago, British Columbians made Vancouver and their province one of the major centres of opposition to the Alaska Pipeline and Tanker System - with some justification, it now seems.That a British Columbian , then MP David Anderson, was given legal recognition to sue in a United States' court against a system that was either in U.S. territory or international waters was an important precedent in, and of, itself in terms of environmental law. That old controversy is now a very current case study - in terms of dealing with the question of liability.-"

Jan 1, 1991

By O. G. Olvera, L. S. Quiroz-Castillo, P. J. Valenzuela-Guerrero, D. G. Dixon

The effect of sulfuric acid concentration on the extractions of arsenic and copper in the catalyzed batch leaching of an enargite concentrate was studied. The acid concentrations studied were 60, 45, 30 and 15 g/L. The experimental series yields maximum copper extractions of 96 to 98% in an interval of 81 - 185 h leaching time for 60 - 15 g/L initial sulfuric acid concentration; all the copper extractions plateaued after these values; the rates and plateaus of copper extraction are increased with higher acid concentrations. Arsenic extractions reached maximum values of 89% in 57 hours, 57% in 49 hours, 33% in 25 hours, and 25% in 112 hours respectively; these maximum values were followed by a steep decrease in arsenic concentration, which indicates a precipitation event occurs in the process. According to the literature and process conditions, the arsenic precipitates obtained are iron arsenates similar to scorodite. The stability of the residues was tested using the Toxicity Characteristic Leaching Procedure (TCLP) from EPA; the residues for the four concentration levels passed the TCLP test, reporting arsenic leaching values below 1 mg/L.

Jan 1, 2014

By Sylvie Poirier

This paper focuses on new developments regarding thermal rock fragmentation applications. The technology consists in a strong burner powered by diesel fuel and air. The thermal reaction, which is created, allows for the enlargement of 125-mm to 450-mm holes by breaking the rock in a spalling effect. It has been used for over 30 years in Russian open pit mining. Following an agreement between Dynamitage T.C.G. Inc. and the owner of the technology, major improvements have been brought to this technology, allowing for the fabrication of a prototype suitable for the Canadian industry. In Russia and Ukraine, thermal rock fragmentation is actually used to drill large diameter holes in surface mining. Upon having acquired a better knowledge of this technology, it seems that it presents a great potential for selective mining in narrow-vein operations, for either surface or underground mining. Rocmec International Inc., a subsidiary of Dynamitage T.C.G. Inc., and Natural Resources Canada are technical partners in the evaluation of the operational parameters and environmental aspects, such as gas, heat, dust and fog emissions. Furthermore, Canada Economic Development is a financial partner in this project. This paper presents the technology and its history. It also reports on the changes brought to the equipment to adapt it to North American environments. A summary of the tests realized since 1995 is provided, along with the main conclusions obtained. The anticipated applications for the use of this technology in both surface and underground environments are described, such as open pit mining, bulk sampling and narrow-vein ore extraction. An estimate showing a comparison between the thermal fragmentation mining concept and the long-hole mining method is presented and, finally, the future developments planned are listed.

May 1, 2002

By K. Cybulski

Coal dust explosions still remain the main hazard in the coal mining sector, notwithstanding their relatively wide recognition compared to other hazards and the development of effective methods of prevention. Coal dust explosions are still the cause of numerous catastrophes, often leading to fatalities. Fortunately, they rarely occur, and it is for this reason that their hazardous impact is often underestimated. This problem in Poland is being exclusively solved by the Central Mining Institute, Experimental Mine Barbara. Here, basic research on the phenomenon of coal dust explosions and prevention methods is carried out, as well as investigations into the causes and circumstances of past accidents. After 15 years of no coal dust explosion accidents in Poland (1987?2002), a few coal dust explosions have recently occurred, with tragic consequences. These events have taken place not only in hard coal mines, where the presence of dangerous coal dust is the result of common production cycle, and safety measures against coal dust explosions are subject to specific regulations, but also in coal-fired power plants. This is of special concern because prior to 1987, such accidents had been been reported only for coal mines and not for coal-fired power plants. In recent years, two dust explosions occurred in Polish power facilities: the Dolna Odra and Turow power plants. In both cases, coal dust explosions occurred in the fuel supply system, but biomass dust was also involved. The explosions caused significant damage to the systems and buildings. This paper gives description and schematics of the regions of catastrophic coal dust explosions that have occurred in recent years in Poland, as well as the results of post-accident investigations, presenting the coal dust explosion hazard at the accident scene The results specify in detail the state of safety measures against coal dust explosions in light of the relevant regulations in force, including amount of deposited coal dust, content of incombustible matter in coal dust, free moisture content in coal dust, state of coal dust explosion safety zones, and state of explosion barriers. The conclusions from the site inspection and post-accident investigations presented enable us to determine locations of explosion initiation, probable ignition sources, range of explosion flames, and explosion barrier performance. A complete elimination of coal dust explosion hazard at the site of dust deposition is practically impossible to achieve. Similarly, a total elimination of ignition source, which may be related to the occurrence of other natural hazards, equipment malfunction or human errors, is impossible. The examples of tragic events that took place in Polish coal mines and coal-fired power plants highlight shortcomings and mistakes made in terms of assessment and prevention measures taken against the coal dust explosion hazard.

Aug 1, 2013

By John C. Loretto

"The paper identifies two of the main problems encountered in recent hydrometallurgical plants for the recovery of gold and silver: firstly, the plant recovery is lower than anticipated from the testwork; secondly, the metallurgical accounting figures cannot be reconciled.The principal reasons for the plant recovery being lower than the testwork are discussed, together with solutions that can minimize these problems both during the design stage and during the plant operation after the problems have manifest themselves.The reasons for the difficulties in metallurgical accounting are analyzed by reviewing the various components of the plant figures. Recommended solutions are given for minimizing this problem and the realities of obtaining accurate figures are discussed.IntroductionThe start-up over the last few years of new hydrometallurgical plants for the recovery of gold and silver has brought to the surface again a number of problems. Most of the problems have existed for some time and they manifest themselves mainly in two ways. Firstly, the plant results do not agree with the metallurgical testwork figures; secondly, the metallurgical accounting figures do not balance.Metallurgical TestworkThe plant results not agreeing with testwork figures are mainly due to:a) testwork samples not representative of the eventual plant feed;b) misinterpretation or misunderstanding of testwork ;c) plant losses;d) plant design not allowing testwork results to be achieved;e) operating deficiencies."

Jan 1, 1982

By B. B. Meadows

"The Minto-Chipman Strip Mining Reclamation Project was initiated to re-vegetate the spoil piles remaining from strip mining operations.All available information was studied by the team responsible, and areas being reclaimed in the U. S. were visited, Methods applicable to the N. B. Project were noted for future use.We have both surface and underground mining operations in New Brunswick, Both deface the natural landscape and reclamation varies in difficulty, Surface operation disturbances are the most difficult to correct.Some of the surface mining is carried out next to two main highways and the results are definite eyesores, With this in mind, it was decided to landscape the spoil ground next to the highways and plant “as is"" the ground remote from the public view.The landscaping entailed various degrees of bulldozing from complete levelling to contouring, smoothing and topping, Bulldozing is, of course, the most expensive part of any reclamation project.There are two phases to the planting program; experimental and operational--experimental both prior and, later, in conjunction with the operational planting.Initially in the experimental project, the pH and composition of the spoil was determined using a grid sampling system. Soil samples were tested in a laboratory at the University of New Brunswick."

Jan 1, 1970

By CIM Mineral Resource

On January 9, 2018, the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Council formed the CIM Mineral Resources and Mineral Reserves Committee (CIM MRMR Committee), which is a combination of the previous Standing Committee on Reserve Definitions and the Best Practices Committee. As part of its mandate, the CIM MRMR Committee updates guidelines for use by Industry, which include the Uranium Practice Guidelines. The 2024 CIM Uranium Leading Practice Guidelines were adopted by CIM Council on November 22, 2024, and supersedes the 2003 version. The main principles and guidelines relating to preparation of Mineral Resource and Mineral Reserve (MRMR) estimates are provided in the CIM Estimation of Mineral Resources and Mineral Reserves Best Practices Guidelines (MRMR BP Guidelines, as updated from time to time). The MRMR BP Guidelines provide information pertaining to metalliferous and other deposits and many sections are readily applicable to the preparation of MRMR estimates for uranium deposits. However, additional guidance is appropriate for uranium deposits due to the radioactive nature of uranium, and its amenability, in some cases, to in situ recovery (ISR) mining methods.

Nov 1, 2024

By Eugene Barsky

"At present, theoretical concepts of gravitational separation processes are mainly limited by the study of the interaction between a flow and a solitary particle. Then the main conclusions of this analysis are applied to a mass process. However, this analysis is absolutely insufficient, because some elementary phenomena such as the ingress of coarse particles into the fine product output and vice versa cannot be interpreted from its standpoint. It is also impossible to predict the results of the classification of a material with a specific granulometric composition on a specific apparatus on its basis.In the present paper, an extended model of the process is suggested. The model is based on the behavior of all the particles of a specific narrow size class, and not on that of an individual particle. Similarity criteria of the process, which were empirically derived previously, are obtained from the analysis of this model.INTRODUCTIONIn case of gravitational separation, a part of solid phase moves, as a rule, vertically upwards with the flow, while another part settles against the flow. This flow is extremely complicated and chaotic due to various random factors. Among these factors are mass interactions of particles with each other and with the apparatus walls, non-uniform character of concentration and velocity fields, turbulent vortices and local fluctuations, real particles shape difference from spherical one, etc.Particles rotation results in a transverse force (Magnus' effect). At the motion of a non-rotating particle in a non-uniform velocity field, a transverse force also arises (Saffman's effect).A great number of publications have been devoted to the account for all these factors in two-phase flows in recent decades. Very complicated models have been developed, but the problem has not been completely solved as yet [1, 3].At the same time, simplified models of the behavior of a solitary particle in a flow are being developed. Despite their schematic nature, such models often prove to be useful for establishing general laws of the process and its similarity criteria [1]."

Jan 1, 2016

By John Hansen

This paper has been written for presentation at the 103rd Annual General Meeting of the Canadian Institute of Mining, Metallurgy, and Petroleum, April 29 to May 02, 2000. The paper addresses blast pattern fragmentation and diggability versus the blasting technique used. RESUME The author is the Vice President for Thunderbird Mining Systems. In this capacity he manages the mine site installation of surface mining mobile equipment monitoring and navigation systems. These systems are onboard instrumentation and software systems designed to: ??measure and log mobile equipments? production and health; and ??direct the equipment operators via onboard displays that show comprehensive maps and engineering instructions. The author is a mining engineering graduate from the Royal School of Mines. His work experience includes front line supervisor and mining engineer for Hudson Bay Mining & Smelting, mining engineer for Teck Corporation, and mining consultant for PriceWaterhouseCoopers.

May 1, 2001

The Red Lake greenstone belt is an irregular mass of lavas sedimentary rocks and intrusives which is approxiately 35 miles long 18 miles wide and 7 miles deep. Basaltic volcamcs are the oldest rocks w1thm the belt. They are believed to have been laid down on an ancient crust which is at least 3 billion (3 x 109) years old and was composed partly of sediments. The basaltic rocks are overlain by acid volcanics and sedimentary rocks which have been complexly folded and are preserved as a down-folded remnant of younger rocks within the older crust. The volcanics and sedimentary rocks of the greenstone belt have been cut by intrusives with a wide range of composition. The emplacement of the intrusives and the accompanying regional metamorph-ism which terminated the orogenic activity in this area are believed to have occurred approximately 2.4 billion years ago. The basalts and many of the basic and ultrabasic intrusives undoubtedly had their source in the sub-crust or mantle. At least some of the granitic intrusives are believed to have had

Jan 1, 1965

By J. J. Jonas, G. R. Stewart, A. M. Elwazri

Two important parameters for dynamic recrystallization can be derived from the changes in the strain hardening rate: the critical strain for initiation of dynamic recrystallization and the point of maximum softening. In this work, these values are determined from the flow stress-strain data obtained in continuous compression testing in the range 900-1100°C. The resulting strains are used to calculate a kinetic model of dynamic recrystallization for two materials: 304 austenitic stainless steel and a hypereutectoid plain carbon steel. The mechanical parameters used to define the proposed model are confirmed with quantitative metallographic analysis of the recrystallized microstructure.

Jan 1, 2004

By W. Petruk

A study was undertaken to determine whether interrelations between mineral grains affect ore breakage during grinding, and to establish a correlation between ore breakage and mineral liberation. A base metal ore from the Brunswick No. 12 deposit in New Brunswick was ground for different periods of time in a laboratory ball mill, and both the unbroken ore and the ground products were analysed by image analysis. The results show that the mode of breakage is strongly influenced by the behaviour of pyrite. Similar size distributions were obtained for material from the 15 minute grind in a laboratory ball mill, for the grinding circuit discharge from a commercial mill, and for pyrite grains in the unbroken ore. This similarity indicates that a 15 minute grind breaks poorly bonded pyrite grains along grain boundaries, and represents the limit of easy breakage for the ore. Such a grind liberates both large separate grains of ore minerals and poorly bonded mineral grains that occur in interstices among pyrite. On the other hand the 15 minute grind does not separate moderately bonded mineral grains nor release moderately bonded interstitial minerals from pyrite; a 45 minute grind in a laboratory ball mill is required. It is assumed that, for Brunswick No. 12 ore, a 45 minute grind in a laboratory ball mill is equivalent to regrinding in a commercial mill. Grinding beyond 45 minutes in a laboratory ball mill breaks the ore by fracturing pyrite across grain boundaries and by chipping grain edges. Such intense grinding does not markedly increase sphalerite liberation from Brunswick No. 12 ore, because most of the sphalerite that can be released was liberated at the 45 minute grind. In contrast the intense grinding increases galena liberation because a significant proportion of the galena occurs as minute inclusions in pyrite. These findings show that ore breakage and coincident liberation depend upon size distributions, intergrowths, and mode of occurrence of the minerals in an ore.

Jan 1, 1988