Search Documents

By K. A. Clark

SEPARATION of the oil from the bituminons sands of the Athabaska area of Alberta has been a subject of study by the Research Council of Alberta. The results of the study have been published in the Annual Reports of the Council. However, the last Annual Report in which there is mention of bituminons sand separation is that for 1934. The attention that is being directed toward the bituminons sands at the present time calls for an up-to-date summary of the work of the Research Council of Alberta on the hot-water separation process. STATEMENT OF FUNDAMENTALS OF HOT-WATER PROCESS Studies of the hot-water separation process have been largely empirical in nature. The objective sought has been a complete recovery of oil from the sand in the form of a separated oil which, itself, is free from mineral matter. Various procedures have been tried in the hope of attaining this objective and a very considerable mass of observations and background of experience have been acquired. lt is rime that a theory for hot-water separation should commence to emerge. As a start toward the formulation of such a theory, the statements which follow regarding the constitution of bituminons sand and its reactions with water and air are presented. It is not pretended that they are entirely correct, but it is believed that they lie not far from the truth. (1) Bituminons sand is an aggregate of sand, clay, oil, and water. The sand consists mainly of quartz particles of 100 ta 200 mesh size and smaller, but also of particles of other minerais including mica, rutile, ilmenite, tour-maline, zircon, spinel, garnet, pyrite, and lignite. Clay occurs interbedded with the bituminons sand, of which, also, it is a constituent. lronstone nodules of all sizes up to eight inches in diameter are likely to be present in the bituminons sand beds. The oil is viscous, naphthenic, and of a specific gravity slightly greater than that of water. The oil content ranges up to, and sometimes even exceeds, 17 per cent by weight. Rich bituminons sand from beds not invaded by water has a water content of 3 to 5 per cent by weight. The water is probably present as a film around the sand particles. The oil surrounds the moist sand grains as an envelope. (2) Water wets quartz and other siliceous minerals more readily than does mineral oil. Consequently, water tends to displace the oil film surrounding the quartz and other siliceous particles when the bituminons sand is mixed with water. Whether the oil is completely displaced depends on the properties of the water. That is to say, the materials dissolved or suspended in the water modify its wetting properties.

Jan 1, 1944

"Conveyed coal flows have been diverted on the basis of real time ash analysis since the 1980s. Many coarse particle separation methods are available through screens, jigs, heavy media separation, particle sorters, to name a few, however bulk diversion requires a representative, continuous analysis to ensure diversion decisions can be made with confidence. Sensors also need to be able to provide measurements at useful time increments so that small tonnages can be diverted for maximum selectivity. Particle separation typically requires high capital costs and there are limitations either in throughput tonnage or particle size or both. Few techniques are able to provide robust and representative analysis of conveyed flows in a useful time basis. Prompt Gamma Neutron Activation Analysis provides multi-elemental analysis of conveyed bulk materials and has been proven in the minerals industry since 2003. This paper outlines the success of this technology in minerals applications in iron ore, phosphate rock and most recently in copper-gold ores, including its use in bulk diversion.INTRODUCTION Naturally occurring quality variability, or heterogeneity, in mineral deposits enables separation and recovery of the valuable components through mining and processing operations. There are distinct advantages in processing the minimum quantity of material to achieve the highest possible yield. Unfortunately, declining ore grades has resulted in larger scale operations and a subsequent loss in selectivity for mining operations. As limits are approached on the practical size of equipment, there is more motivation to investigate alternative solutions. Mining companies are subject to increasing social resistance to growing waste disposal requirements in addition to higher energy and transport costs. Major savings are available by reducing the quantities of material processed where pre-concentration can be effectively applied at early stages in the process. One of the simplest ways to pre-concentrate is to measure the bulk material and reject waste soon after mining so that minimal expense is incurred and that only higher quality material is sent to processing operations. This bulk sorting can occur within the mining operations and has major benefits through energy and other consumables savings. This paper discusses the application of real time analysis technologies suitable for bulk sorting within the minerals industry. Technology that has proven representative for conveyed material bulk analysis and its successful applications to date is explained. Analysis using a sensing technique is only one component of a successful bulk sorting process; the importance of effective diversion systems and a bulk sorting strategy are also discussed. The bulk sorting stage may be one component of a system that could include additional downstream technologies such as particle based sorting systems on a diverted stream."

Jan 1, 2018

By P. Bakke

Following extensive R&D efforts, Hydro Magnesium has launched a new alloy series with remarkable combinations of properties. The AE alloy family is based on additions of aluminium and rare earth elements to control mechanical properties, including elevated temperature creep strength. By combining these alloying elements with manganese additions, high purity alloys with outstanding corrosion performance are defined. A basic philosophy behind the developments has been to simultaneously approach all the critical issues related to developing a commercial material. Apart from the obvious requirements for material properties, the critical issues relate to die casting performance, as well as alloy production, recycling and environmental compatibility. Some of the important elements related to alloy production and recycling are addressed in the present paper.

Jan 1, 2006

By D. K. Fountain

"High metal prices and advanced technology in open-pit mining methods have resulted in considerable interest in the development of large, low-grade mineral deposits. Brenda Mines Limited is presently testing such a deposit of copper-molybdenum mineralization near Penticton, British Columbia.The mineralization of economic interest at Brenda has a total metallic sulphide content of between 1 and 1.5 per cent. This sulphide content approaches the limits of detectability of standard geophysical methods. How-ever, due to a favourable geological environment, it has been possible to utilize the Induced Polarization Method to outline the mineralization at the Brenda property."

Jan 1, 1968

By G. B. Hudson

Previous papers (1, 2) pertaining to the treatment of uranium-bearing ores were concerned with the flotation of the radioactive minerals. In this investigation, the application of flotation to the removal of acid-consuming minerals from uranium ores was considered. Two pitchblende-bearing ores, which, because of the presence if dolomite were abnormally high acid consumers, were studied. In both in-stances commercial reagents of widely varying fatty acid composition proved satisfactory as flotation col-lectors, particularly at a pH of 10.5, for the carbonate minerals. From an economic viewpoint, however, Neo-Fat 42-12 was favoured. A mixture of sodium tripolyphosphate and citric acid was an effective depressant for the pitchblende in the ores. The tailings remaining after the removal of the dolomite by flotation contained, in one case, 88.5 per cent of the uranium in the original sample, and, in the other, 93.8 per cent. Analyses conducted on these tailings and on the original ores showed that

Jan 1, 1963

By J. E. Udd, L. P. Geldart, B. B. Dhar

"Solutions for the stress distributions around simulated underground openings have been limited to calculations of boundary stresses for simple openings in which the boundaries may be expressed in mathematical terms. Studies involving circles, ellipses and ovaloids are re-ported in the literature.The stresses on the boundary of an opening and those at a distance from it in the medium are of concern to the engineer. The former may be related to the greatest concentrations of stresses encountered; the latter have a bearing on the identification of the ""zone of influence"" of the opening.Recent advances, in the form of a derivation for the stresses at a distance from an opening of elliptical shape, together with a solution derived previously for stresses in depth around ovaloidal openings, have been combined with computer programming techniques to provide complete solutions for a wide range of cases and variables. Some typical results which, it is hoped, may have some application to the design of underground openings are given herein."

Jan 1, 1970

By T. N. MacAuley

"The Ingerbelle and Copper Mountain deposits are located near Princeton in southern British Columbia. They are owned by Newmont Mining Corporation's wholly owned subsidiary, Similkameen Mining Company Ltd. The property includes the Copper Mountain mine, a former producer. Ore reserves recoverable by open-pit mining are estimated to be 76 million tons containing 0.53% copper. Production commenced during 1972 at a rate in excess of designed capacity (15,000 tpd). All of the known major copper deposits in this area lie in a 14,000- by 3,500-foot belt of Triassic volcanics (Nicola Group) that is situated between a well-defined syenitemonzonite- diorite stock on the south and a variable intrusive complex on the north. The Nicola rocks consist of andesitic tuffs and agglomerates with lesser amounts of flows and some lensy siltstone layers. The orebodies are essentially disseminated sulphide deposits, although fracture-fillings are also important in many areas. Total sulphide content is usually less than 5%. At lngerbelle, and at Pit 2 and most of Pit 1 at Copper Mountain, the sulphides are chalcopyrite-pyrite. In part of Pit 1 and most of the former underground mine they are chalcopyrite-bornite. At lngerbelle the predominant alteration associated with mineralization is a pale greenish-gray bleaching of the dark andesitic rocks. This has been identified as albitization, with lesser amounts of epidote, chlorite, biotite, scapolite and calcite. This bleaching is plentiful at Pit 2, but K-feldspathization is also evident here. These orebodies can better be classified with pyrometasomatic deposits than with typical porphyry coppers. Their relationship to intrusives, the probably extensive metasomatic replacements, the evidence of pneumatolytic activity, the formation and redistribution of magnetite, and the irregular distribution of mineralization are all characteristic of this class. Deep-seated faults probably acted as channelways for mineralization; fracturing, faulting and rock contacts influenced ore localization in detail."

Jan 1, 1973

By Leonard L. Fischman

It is important to define "adequacy," and the most useful definition is a continuing availability of mineral materials under cost and other conditions which imply no significant burden on the achievement of otherwise attainable levels of consumption and well-being. For current decision making, it is sufficient to consider adequacy just to the end of the century, with some regard being given to then remaining mineral inventory. A comparison of cumulative demand projections to the year 2000 with already identified reserves ( economically recoverable amounts in known deposits) suggests little reason for concern with world adequacy of iron ore, aluminum, manganese, chromium or potash. Conservative estimates of "prospective" reserves (amounts producible at today's prices, but yet to be discovered) suggests that there are ample quantities of virtually all other mineral resources as well. A probable exception is oil and gas, of which there may be scant amounts remaining after the turn of the century. However, there is an evident sufficiency of substitute forms of energy, though it is difficult to see just where developing technology will take us. The critical questions have to do with the increasing dependence of the industrialized countries on external sources of supply , coupled with a new international politic s which complicates the problem of insuring timely development of, and access to, remaining deposits. In this context, Canada, a still mineral-rich nation, is in one of the more favorable positions.

Jan 1, 1977

By X. L. Song, G. W. Zhang, F. Y. He, X. Xiao, L. L. Huang

This paper presents the design of a model and process simulation of a vertical mill based on a population balance model. The simulator, Simulink, which is a systematic modeling tool within MATLAB, was used for the simulation. The model will simulate the real time variation trend of each size fraction in the feed material to the vertical mill, as well as, the size distribution of the batch grinding products. Breakage distribution and selection functions are calculated based on batch grinding laboratory experiments using Back-calculation method. The simulated size distributions correspond with those in the actual mill operation having a relative error of less than 0.50%. This work lays the foundation for future research on modelling and simulation of a closed circuit grinding operation consisting of a vertical mill with hydrocyclone classifier.

Jan 1, 2016

By Anthony J. Deevy

"Abstract -The Magino gold mine is located 45 km northeast of Wawa, Ontario. There was limit­ ed gold production in the Iate thirties. The present operation was officially opened in October 1988 and produced gold until September 1992. It was a 635 tonnes per day, decline-accessed mine, with ore coming from several small blast hole and shrinkage stopes.The host for the gold is the Webb Lake granodiorite stock which was intruded into the Goudreau Lake Deformation Zone. This east-northeast-striking deformation zone overprints the generally east­ west-striking isoclinally folded metavolcanic and metasedimentary rocks, which make up the east end of the Michipicoten greenstone belt. The ore-shoots are controlled by dextral delatancy associated with the Goudreau Lake Deformation Zone. Shearing, bleaching and silicification accompanied the gold emplacement."

Jan 1, 1994

By E. H. Dudgeon

In order to make increased use of automation in copper smelting, it is evident that a useful first step .world be the accurate determination of the copper end point in the converter operation. After laboratory tests, the copper end points in a copper converter at Gaspe Copper Mmes Ltd. were determined without reference to melt samples or other observations. The results indicated that the rapid measurement of the S02 level in the gas released from the converter has potential as a new and independent method of determining the copper end point in converter operation.

Jan 1, 1966

By William Winsor, Harold L. Snyder

"AbstractShould oil and gas be proven in commercial quantities on the Labrador Shelf, current technology is not adequate for production operations in this severe environment, which includes yearly invasion of pack ice and icebergs. The fishery of this section of the North Atlantic is a vital resource to which a major oil spill or blow-out would impose an intolerable burden, This means that production systems must be designed and built to be fail-safe.The experiences of mining in Bell Island and Cape Breton have shown that it is possible to operate beneath the ocean floor, and this technology may hold the key for safe, reliable and economic production, This paper attempts to define particular problems and outline possible solutions.IntroductionOUR DISCUSSION is subject to the assumption that large hydrocarbon reservoirs will be discovered in the sedimentary basin of the Labrador continental margin. The petroleum industry has not attempted to operate in a harsher area. The Labrador coastline is exposed to North Atlantic storms and icebergs year’round, Arctic pack ice occurs up to six months of each year. However, there is no doubt that, if sufficient hydrocarbon potential is outlined, development will proceed."

Jan 1, 1977

By M. B. Mansur, A. S. Guimarães, A. J. M. Santanilla, D. C. R. Espinosa, J. A. S. Tenório, R. A. Pini

The separation of Ni and Co from sulphate medium containing Mn, Mg, Cu and Ca was carried out by solvent extraction. The object of this study was to investigate the synergistic effect using phosphinic acid (Cyanex 272) and carboxylic acid (Versatic 10) and their mixtures in kerosene. The extraction percent of each metal ion was found to increase with increasing pH and extractant concentration. Co was preferentially extracted over Ni under the same extraction conditions. The separation factors of Ni/Co increased with the use of the synergistic systems investigated.

Jan 1, 2014

By I. Cotman

Dimensional stone processing has become an important part of the world extractive industry, and today?s total stone block yearly production is estimated to be around 134.000.000 tons and is still growing by an average yearly rate of approximately 20%. In future, the same production will become an important part of the mining industry and presently, in some countries it represents even the main mining output. New environmental regulations, together with landscape and nature conservation requirements, create a number of difficulties in setting up new open pit dimensional stone quarries. As a result, many dimensional stone producers have recently started to apply underground techniques in order to produce the ornamental stone blocks intended for further processing. Underground production of stone blocks requires special mining methods and so far it has not been a cost-effective excavation method for all types of rocks. Presently, this type of stone excavation is generally applied in sedimentary and marble deposits because the rock has small to no mineral quartz content. When starting a new underground dimensional stone mine, it is necessary to analyse the impact of all primary factors which are crucial to set up a technically and cost effective advanced underground dimensional stone mine. The role of physical and mechanical properties of the rock, geological conditions, mineralogical composition, micro-tectonic state of the site, rock mechanic conditions on the site, durability and saw ability of the stone are decisive factors in foreseeing the future methods of extraction. The laboratory research work as well as the field work, is very important in decision-making aimed to choose the future excavation method. Also of equal importance is the serious market research, because it renders the indication of selling price potential. Having obtained the results from both types of research, mining engineers can design the mining methods which optimize financial return to the mine. The practice approved by 15 years of testing in the underground limestone quarry of Kanfanar gives future producers very useful advice and general data to facilitate the process of exploration intended to establish new similar underground quarries.

Aug 1, 2013

By A. Paulin, J. Roth, S. Spaic

This experiment was carried out to see whether copper-iron ingots from Late Bronze Age hoards could have been produced by smelting ferruginous copper ores. Since ferruginous copper-ores are chalcopyritic, chalcopyritic concentrate from a present day copper mine was dead roasted in our experiment in lieu of a rich chalcopyritic ore. Charcoal was used as a reducing agent in the reduction of calcine (i.e., a product of dead-roasting), and quartz sand was used as a flux. Two separate metallic solutions, a copper-base and an iron-base alloy, were obtained as a result of two factors: the presence of carbon and the miscibility gap in the Cu-Fe-C system. The metallic melts appeared in a form of bigger or smaller droplets, enclosed by a molten slag which, during the cooling, solidified into metallic beads. The presence of both metals was noticed in the majority of the examined beads. It was therefore concluded that calcine consisted of an intimate mixture of oxides of both metals which were simultaneously reduced during the reduction process. Due to the miscibility gap in the Cu-Fe-C system, separate iron and copper regions were formed in the beads. In both regions, sulphide inclusions were found. The formed molten copper and molten iron solution were found to be saturated solutions. The metallographic analysis revealed the precipitation of iron out of copper and that of copper out of iron during the cooling and solidification of melts. The formed slag contained little iron and no copper oxide.

Jan 1, 2001

By E. Quaquero

This article reports on the current state of an ongoing research project which is aimed at implementing intelligent models for hardly predictable hazard scenarios identification in construction sites. As past evidences showed that no programmatic action can deal with the unpredictable nature of many risk dynamics, we tried to survey on how the current approach for safety management in the construction industry could be improved. In our previous research the use of Bayesian networks elicited from subjective knowledge were preliminarily tested. Those networks might be meant as a reliable knowledge map about accident dynamics and they showed that a relevant ratio of occurrences fall in ?hardly predictable hazards? class, which cannot be warded off by programmatic safety measures. This paper reports the second outcome of our research project, which focused on the development of first elementary fragments, regarding the occurrence of a possible ?hardly predictable scenario?. Instead of experts? contributions (who, over their carrier, seldom incurred in accidents), we used ?legal cases? as an accurate source of information. They suggested which categories of ?hidden hazard scenarios? are more likely to happen. We found that the most frequent hidden hazard scenarios are linked to operator?s negligence and abnormal behavior, e.g. irregular removal of scaffolding?s components, unprotected openings, improper use of PPE, etc. Every pattern determined by legal cases has been formalized by a fragment (i.e. elementary network) of the overall Bayesian network. Finally, all the elementary networks were integrated into a comprehensive intelligent tool for realtime hardly predictable hazards prevention. The final setup, asked for interfacing these intelligent models to a low-level sensor network and used to feed them with inputs about the current state of the context, is discussed too.

Aug 1, 2013

By F. Vahdatikhaki

Simulation techniques have offered significant boosts toward a cost-and-time-optimized planning of construction projects by enabling project managers to effectively comprehend the behavior of projects. Using historic data from projects of like nature, simulation considers uncertainties involved in a project through accommodating the stochastic modeling parameters. However, the heavy reliance on the statistical data and not taking into account the context-specific features of the project cause the degradation in the realism and accuracy of the simulation models. Similarly, the extent to which a historic pattern could be retrofitted to new projects will decrease in line with the growing uniqueness of the projects and the novelty of construction methods. Furthermore, the existing real-time simulation frameworks are not capable of distinguishing the transient environmental changes, with minimal long-term impacts on the productivity, from the influential changes that will greatly impact an operation. In addition, existing simulation tools are devoid of location awareness, resulting in the inability to consider safety threats in their representation of the project. To address these issues, this research proposes a framework based on the integration of new tracking technologies used in Automated Machine Guidance (AMG) with simulation-driven 4D modeling methods. The proposed framework automates the adjustment of the simulation model based on the updated data from the site, and thus transforms simulation from a predictive tool used at the planning phase to a proactive monitoring platform usable throughout the planning and construction phases. A prototype is developed to test and demonstrate the effectiveness of the proposed approach.

Aug 1, 2013

By S. Y. Ezz, K. El•Guindi

A vertical tube, 8 m long and 2.5 cm in diameter, electrically heated to 650°C throughout the majority of its height, was used to study the-effect of ore feed rate and hydrogen flow rate on the reduction of fine iron ore particles. A correlation could be obtained between the combined effect of the amount of reducing gas and reduction time and the per-cent reduction. The results suggest that a method based on the reduction of fine iron ores while falling through up-streaming hydrogen cannot be recommended for industrial application.

Jan 1, 1969

By J. L. Feng, F. Zhang, S. K. Hu

"Cracking is one of the most serious damages in tunnel linings, which is often observed by in-situ inspection to tunnel engineering. It is difficult to better characterise for the deformations from continua to discontinua by the traditional continuum mechanics due to emerging of crack initiation, crack propagation, and coalescence, at several scales. In this paper, the process of failure that was from micro damage to macro crack in concrete tunnel linings under experimental load conditions, was quantitatively simulated by the combined finite-discrete element method (FDEM). Comparison of the simulating results with that obtained by the full-scale test of concrete lining under different loading conditions in the literature was respectively good agreed and shows that such FDEM technique is appropriate to model the continuousdiscontinuous problems. The present study indicates that the FDEM technique could be benefit to quantitatively evaluate the stability and damage level of tunnel lining system. INTRODUCTIONMost damage to tunnel linings is caused during the construction phase, which can emerge in a form of single macro cracks or even large-scale spalling. The cause of such damage is mostly the occurrence of, either impermissibly large contact stresses resulting from high thrust loads combined with production and installation tolerances in the segments resulting in a geometrical lack of fit (Maidl et al., 2012; Transportation Research Board, Basic Research and Emerging Technologies Related to Concrete Committee, 2006), or unallowable tensile/shear stresses appearing in the tunnel linings under complicated loading conditions (Ansell, 2010). Such a macro failure phenomenon may also be regarded to as a result of growth, coalescence, initiation of microcracks in tunnel linings due to the complicated loading action, and even potentially lead to an instability or collapse of the local or entire tunnel system. Much work has been devoted to investigate for the characters of micro and macro cracks, the influence factors of damage patterns, the settlement of a tunnel, the width, length and density of lining cracks, especially from classifiedly and qualitatively (Wang, 2010; Huang et al., 2013). However, the safety evaluation of tunnel is definitely required to not only inspect in situ, but further also quantify computing and analyzing for tunnel lining systems, so as to provide a global viewpoint of process of the tunnel deformation, which aims to help for subsequent decisions, e.g. controlling traffic flow or immediately repairing task. Additionally, the design of lining thickness and its structural analysis that is mostly determined by previous experience and similar construction examples is also needed to be improved."

Jan 1, 2015

By Jean-Christophe Ehrström, Fanny Mas

"A specific test set-up has been developed to study at the lab-scale the high-temperature behavior of aluminium alloys in conditions close to those experienced by thick plates during hot-rolling. A particular attention is paid to reproducing both the stress triaxiality and strain fields that exist in plate during rolling. In addition to standard ductility measurements by means of secondary tensile tests (STT), multi-step plane strain compression (PSC) tests have been performed to mimic hot-rolling pass schedules. Tool and sample geometries were adapted to allow low h/a ratios (h= average specimen thickness, a= tool width) and thus guarantee depressive stress conditions at the center of the specimen during most of the test. Such conditions resulting in porosity opening can then be used to investigate the impact of rolling conditions on damage evolution. The mechanical testing was combined with post-mortem high-resolution ultrasonic scans allowing to detect small amounts of damage and quantify its evolution as a function of processing parameters such as strain and temperature. The test set-up was validated on two 2050-type AlCuLi alloys with different susceptibilities to high temperature embrittlement.INTRODUCTION Aluminium thick plates are widely used in the aerospace industry, mainly as semi-products to be machined for internal structure parts of wings (spars, ribs) and fuselage (frame). The conversion route of such products always involves a hot-rolling step, the conditions of which (temperature, speed, pass schedule) have to be optimized to maximize both mechanical properties and final plate quality. This goal cannot always be efficiently achieved by full-scale industrial trials as (a) cost limits the number of possible test conditions and (b) it is often difficult to change one parameter alone. That is why there is a need for laboratory-scale tests able to mimic the rolling process in terms of temperature, strain rate, stress triaxiality and deformation. Most laboratory hot-rolling mills do not adequately simulate industrial processing routes, especially in terms of heat loss, deformation speed and rolling geometry (maximum roll gap vs. work roll diameter). Concerning thick plate, it is of interest to achieve both similar deformation and L/h ratio (L=arc of contact, h=mean gauge) per pass as the industrial schedule because they are simultaneously involved in damage evolution and void closure during hot forming processes (Saby, 2014)."

Jan 1, 2018